Zebrafish irritant responses to wildland fire-related biomass smoke are influenced by fuel type, combustion phase, and byproduct chemistry.

Human exposure to wildfire-derived particulate matter (PM) is linked to adverse health outcomes; however, little is known regarding the influence of biomass fuel type and burn conditions on toxicity. The aim of this study was to assess the irritant potential of extractable organic material (EOM) of biomass smoke condensates from five fuels (eucalyptus, pine, pine needle, peat, or red oak), representing various fire-prone regions of the USA, burned at two temperatures each [flaming (approximately 640°C) or (smoldering approximately 500°C)] using a locomotor assay in zebrafish (Danio rerio) larvae. It was postulated that locomotor responses, as measures of irritant effects, might be dependent upon fuel type and burn conditions and that these differences relate to combustion byproduct chemistry. To test this, locomotor activity was tracked for 60 min in 6-day-old zebrafish larvae (25-32/group) immediately after exposure to 0.4% dimethyl sulfoxide (DMSO) vehicle or EOM from the biomass smoke condensates (0.3-30 µg EOM/ml; half-log intervals). All EOM samples produced concentration-dependent irritant responses. Linear regression analysis to derive rank-order potency indicated that on a µg PM basis, flaming pine and eucalyptus were the most irritating. In contrast, on an emission-factor basis, which normalizes responses to the amount of PM produced/kg of fuel burned, smoldering smoke condensates induced greater irritant responses (>100-fold) than flaming smoke condensates, with smoldering pine being the most potent. Importantly, irritant responses significantly correlated with polycyclic aromatic hydrocarbon (PAH) content, but not with organic carbon or methoxyphenols. Data indicate that fuel type and burn condition influence the quantity and chemical composition of PM as well as toxicity.

Iron solubility related to particle sulfur content in source emission and ambient fine particles.

The chemical factors influencing iron solubility (soluble iron/total iron) were investigated in source emission (e.g., biomass burning, coal fly ash, mineral dust, and mobile exhaust) and ambient (Atlanta, GA) fine particles (PM2.5). Chemical properties (speciation and mixing state) of iron-containing particles were characterized using X-ray absorption near edge structure (XANES) spectroscopy and micro-X-ray fluorescence measurements. Bulk iron solubility (soluble iron/total iron) of the samples was quantified by leaching experiments. Major differences were observed in iron solubility in source emission samples, ranging from low solubility (<1%, mineral dust and coal fly ash) up to 75% (mobile exhaust and biomass burning emissions). Differences in iron solubility did not correspond to silicon content or Fe(II) content. However, source emission and ambient samples with high iron solubility corresponded to the sulfur content observed in single particles. A similar correspondence between bulk iron solubility and bulk sulfate content in a series of Atlanta PM2.5 fine particle samples (N = 358) further supported this trend. In addition, results of linear combination fitting experiments show the presence of iron sulfates in several high iron solubility source emission and ambient PM2.5 samples. These results suggest that the sulfate content (related to the presence of iron sulfates and/or acid-processing mechanisms by H(2)SO(4)) of iron-containing particles is an important proxy for iron solubility.

Chemical characterization of the fine particle emissions from commercial aircraft engines during the Aircraft Particle Emissions eXperiment (APEX) 1 to 3.

This paper addresses the need for detailed chemical information on the fine particulate matter (PM) generated by commercial aviation engines. The exhaust plumes of seven turbofan engine models were sampled as part of the three test campaigns of the Aircraft Particle Emissions eXperiment (APEX). In these experiments, continuous measurements of black carbon (BC) and particle surface-bound polycyclic aromatic compounds (PAHs) were conducted. In addition, time-integrated sampling was performed for bulk elemental composition, water-soluble ions, organic and elemental carbon (OC and EC), and trace semivolatile organic compounds (SVOCs). The continuous BC and PAH monitoring showed a characteristic U-shaped curve of the emission index (EI or mass of pollutant/mass of fuel burned) vs fuel flow for the turbofan engines tested. The time-integrated EIs for both elemental composition and water-soluble ions were heavily dominated by sulfur and SO(4)(2-), respectively, with a ∼2.4% median conversion of fuel S(IV) to particle S(VI). The corrected OC and EC emission indices obtained in this study ranged from 37 to 83 mg/kg and 21 to 275 mg/kg, respectively, with the EC/OC ratio ranging from ∼0.3 to 7 depending on engine type and test conditions. Finally, the particle SVOC EIs varied by as much as 2 orders of magnitude with distinct variations in chemical composition observed for different engine types and operating conditions.

Anterograde coil closure of patent ductus arteriosus using a modified bioptome delivery technique.

Three consecutive patients are presented who underwent successful anterograde catheter coil occlusion of a patent ductus arteriosus using a modified bioptome-assisted technique. Two of the three patients were infants and the procedures were performed without the need for arterial access.

New forceps delivery technique for coil occlusion of patent ductus arteriosus.

We remain very enthusiastic about transcatheter coil occlusion of the PDA. However, surgical ligation has been performed successfully and with relatively low risk of complications. Therefore, an alternative nonsurgical technique must demonstrate comparable success and safety. We believe that this new forceps delivery technique has significant advantages over previously reported PDA coil occlusion techniques and should warrant further clinical investigation.