RESUMEN
Extensively-used rechargeable lithium-ion batteries (LIBs) face challenges in achieving high safety and long cycle life. To address such challenges, ultrathin solid polymer electrolyte (SPE) is fabricated with reduced phonon scattering by depositing the composites of ionic-liquid (1-ethyl-3-methylimidazolium dicyamide, EMIM:DCA), polyurethane (PU) and lithium salt on the polyethylene separator. The robust and flexible separator matrix not only reduces the electrolyte thickness and improves the mobility of Li+, but more importantly provides a relatively regular thermal diffusion channel for SPE and reduces the external phonon scattering. Moreover, the introduction of EMIM:DCA successfully breaks the random intermolecular attraction of the PU polymer chain and significantly decreases phonon scattering to enhance the internal thermal conductivity of the polymer. Thus, the thermal conductivity of the as-obtained SPE increases by approximately six times, and the thermal runaway (TR) of the battery is effectively inhibited. This work demonstrates that optimizing thermal safety of the battery by phonon engineering sheds a new light on the design principle for high-safety Li-ion batteries.
RESUMEN
Co magnetic films are widely used in high-frequency magnetic recording and vertical magnetic recording due to their high saturation magnetization and magnetocrystalline anisotropy. In this work, ferromagnetic Co magnetic films were prepared on copper substrate by vacuum evaporation combined with heat treatment (H2 atmosphere), to investigate the impact of film thickness and annealing temperature on microstructure and magnetic properties. The results show that with the increase in annealing temperature, the Co thin film physical phase does not change significantly, the crystallinity increases, and the grain size increases, which is consistent with the results obtained from the SEM morphology map of the sample surface, leading to an increase in coercivity. By annealing experiments (atmospheric atmosphere) on Co magnetic films with and without an Al protective layer, as shown by scanning electron microscopy microscopic characterization results, it was verified that the Al layer can protect the inner Co layer from oxidation. As the film thickness increases from 10 to 300 nm, the magnetic properties of Co films change significantly. The saturation magnetization gradually increases from 0.89 to 5.21 emu/g, and the coercivity increases from 124.3 to 363.8 Oe. The remanence ratio of the 10 nm magnetic film is 0.82, which is much higher than the film remanence ratio of 0.46 at 50 nm. This is because when the thickness of the film is between 10 and 50 nm, the magnetic moments partially deviate from the in-plane direction, and the out-of-plane component reduces the film remanence ratio. This study shows that optimizing annealing temperature and film thickness can effectively control the structure and magnetic properties of Co magnetic films, which is of great significance for the development of the magnetic recording field.
RESUMEN
Lithium metal is an ideal anode for next-generation high-energy-density batteries. However, lithium dendrite growth has impeded its commercial application. Herein, fabricating Li-based ultrathin alloys with electronic localization and high surface work function via depositing Bi, Al, or Au metals on the surface of copper foil for in situ alloying with lithium is proposed. It is discovered that the electronic localization can induce self-smoothing effect of Li ions, as a result, significantly suppressing the growth of dendritic lithium. Meanwhile, the high surface work function can effectively alleviate side reactions between the electrolyte and lithium. With the as-obtained ultrathin alloys as anodes, excellent cycling performance is achieved. The half cells run stably after more than 120 cycles under high capacity of 4 mAh cm-2 . The S||Bi/Cu-Li full cell delivers a specific capacity of 736 mAh g-1 after 200 cycles. This work provides a new strategy for fabricating long-life and high-capacity lithium batteries.
RESUMEN
This corrects the article DOI: 10.1038/nature23667.
RESUMEN
The ability to control chemical and physical structuring at the nanometre scale is important for developing high-performance thermoelectric materials. Progress in this area has been achieved mainly by enhancing phonon scattering and consequently decreasing the thermal conductivity of the lattice through the design of either interface structures at nanometre or mesoscopic length scales or multiscale hierarchical architectures. A nanostructuring approach that enables electron transport as well as phonon transport to be manipulated could potentially lead to further enhancements in thermoelectric performance. Here we show that by embedding nanoparticles of a soft magnetic material in a thermoelectric matrix we achieve dual control of phonon- and electron-transport properties. The properties of the nanoparticles-in particular, their superparamagnetic behaviour (in which the nanoparticles can be magnetized similarly to a paramagnet under an external magnetic field)-lead to three kinds of thermoelectromagnetic effect: charge transfer from the magnetic inclusions to the matrix; multiple scattering of electrons by superparamagnetic fluctuations; and enhanced phonon scattering as a result of both the magnetic fluctuations and the nanostructures themselves. We show that together these effects can effectively manipulate electron and phonon transport at nanometre and mesoscopic length scales and thereby improve the thermoelectric performance of the resulting nanocomposites.
RESUMEN
Simultaneously optimizing electrical and thermal transport properties of bulk thermoelectric materials remains a key challenge due to the conflicting combination of material traits. Here, we have explored the electrical and thermal transport features of In-filled CoSb3 through X-ray absorption fine structure, X-ray photoemission spectra, transport measurement and theoretical calculation. The results provide evidence of three types of coexisting multi-localization transport behaviours in the material; these are heat-carrying phonon-localized resonant scattering, accelerated electron movement and increase in density of states near the Fermi level. The 5p-orbital hybridization between In and Sb is discovered in the In-filled CoSb3 compound, which results in a charge transfer from Sb to In and the enhancement of p-d orbital hybridization between Co and Sb. Our work demonstrates that the electrical and thermal properties of filled skutterudite bulk thermoelectric materials can be simultaneously optimized through the three types of coexisting multi-localization transport behaviours in an independent way.