RESUMEN
This paper proposes a retinal prosthesis edge detection (RPED) algorithm that can achieve high visual acuity and low power. Retinal prostheses have been used to stimulate retinal tissue by injecting charge via an electrode array, thereby artificially restoring the vision of visually impaired patients. The retinal prosthetic chip, which generates biphasic current pulses, should be located in the foveal area measuring 5 mm × 5 mm. When a high-density stimulation pixel array is realized in a limited area, the distance between the stimulation pixels narrows, resulting in current dispersion and high-power dissipation related to heat generation. Various edge detection methods have been proposed over the past decade to reduce these deleterious effects and achieve high-resolution pixels. However, conventional methods have the disadvantages of high-power consumption and long data processing times because many pixels are activated to detect edges. In this study, we propose a novel RPED algorithm that has a higher visual acuity and less power consumption despite using fewer active pixels than existing techniques. To verify the performance of the devised RPED algorithm, the peak signal-to-noise ratio and structural similarity index map, which evaluates the quantitative numerical value of the image are employed and compared with the Sobel, Canny, and past edge detection algorithms in MATLAB. Finally, we demonstrate the effectiveness of the proposed RPED algorithm using a 1600-pixel retinal stimulation chip fabricated using a 0.35 µm complementary metal-oxide-semiconductor process.
Asunto(s)
Algoritmos , Agudeza Visual , Prótesis Visuales , Humanos , Agudeza Visual/fisiología , Retina/fisiología , Retina/diagnóstico por imagen , Relación Señal-RuidoRESUMEN
In this study, a pulse frequency modulation (PFM)-based stimulator is proposed for use in biomedical implantable devices. Conventionally, functional electrical stimulation (FES) techniques have been used to reinforce damaged nerves, such as retina tissue and brain tissue, by injecting a certain amount of charge into tissues. Although several design methods are present for implementing FES devices, an FES stimulator for retinal implants is difficult to realize because of the chip area, which needs to be inserted in a fovea, sized 5 mm x 5 mm, and power limitations to prevent the heat generation that causes tissue damage. In this work, we propose a novel stimulation structure to reduce the compliance voltage during stimulation, which can result in high-speed and low-voltage operation. A new stimulator that is composed of a modified high-speed PFM, a 4-bit counter, a serializer, a digital controller, and a current driver is designed and verified using a DB HiTek standard 0.18 µm process. This proposed stimulator can generate a charge up to 130 nC, consumes an average power of 375 µW during a stimulation period, and occupies a total area of 700 µm × 68 µm.
Asunto(s)
Terapia por Estimulación Eléctrica , Prótesis Visuales , Electrodos Implantados , Retina , Fóvea Central , Estimulación Eléctrica , Diseño de EquipoRESUMEN
Smartphone-based navigation apps allow blind and visually impaired (BVI) people to take images or videos to complete various tasks such as determining a user 's location, recognizing objects, and detecting obstacles. The quality of the images and videos significantly affects the performance of these systems, but manipulating a camera to capture clear images with proper framing is a challenging task for BVI users. This research explores the interactions between a camera and BVI users in assistive navigation systems through interviews with BVI participants. We identified the form factors, applications, and challenges in using camera-based navigation systems and designed an interactive training app to improve BVI users' skills in using a camera for navigation. In this paper, we describe a novel virtual environment of the training app and report the preliminary results of a user study with BVI participants.
RESUMEN
In this study, we propose a low-area multi-channel controlled dielectric breakdown (CDB) system that simultaneously produces several nanopore sensors. Conventionally, solid-state nanopores are prepared by etching or drilling openings in a silicon nitride (SiNx) substrate, which is expensive and requires a long processing time. To address these challenges, a CDB technique was introduced and used to fabricate nanopore channels in SiNx membranes. However, the nanopore sensors produced by the CDB result in a severe pore-to-pore diameter variation as a result of different fabrication conditions and processing times. Accordingly, it is indispensable to simultaneously fabricate nanopore sensors in the same environment to reduce the deleterious effects of pore-to-pore variation. In this study, we propose a four-channel CDB system that comprises an amplifier that boosts the command voltage, a 1-to-4 multiplexer, a level shifter, a low-noise transimpedance amplifier and a data acquisition device. To prove our design concept, we used the CDB system to fabricate four nanopore sensors with diameters of <10 nm, and its in vitro performance was verified using λ-DNA samples.
Asunto(s)
Nanoporos , Nanotecnología , ADN , Nanotecnología/métodos , Sistemas de Atención de PuntoRESUMEN
Researchers have adopted remote methods, such as online surveys and video conferencing, to overcome challenges in conducting in-person usability testing, such as participation, user representation, and safety. However, remote user evaluation on hardware testbeds is limited, especially for blind participants, as such methods restrict access to observations of user interactions. We employ smart glasses in usability testing with blind people and share our lessons from a case study conducted in blind participants' homes (N = 12), where the experimenter can access participants' activities via dual video conferencing: a third-person view via a laptop camera and a first-person view via smart glasses worn by the participant. We show that smart glasses hold potential for observing participants' interactions with smartphone testbeds remotely; on average 58.7% of the interactions were fully captured via the first-person view compared to 3.7% via the third-person. However, this gain is not uniform across participants as it is susceptible to head movements orienting the ear towards a sound source, which highlights the need for a more inclusive camera form factor. We also share our lessons learned when it comes to dealing with lack of screen reader support in smart glasses, a rapidly draining battery, and Internet connectivity in remote studies with blind participants.
RESUMEN
Teachable object recognizers provide a solution for a very practical need for blind people - instance level object recognition. They assume one can visually inspect the photos they provide for training, a critical and inaccessible step for those who are blind. In this work, we engineer data descriptors that address this challenge. They indicate in real time whether the object in the photo is cropped or too small, a hand is included, the photos is blurred, and how much photos vary from each other. Our descriptors are built into open source testbed iOS app, called MYCam. In a remote user study in (N = 12) blind participants' homes, we show how descriptors, even when error-prone, support experimentation and have a positive impact in the quality of training set that can translate to model performance though this gain is not uniform. Participants found the app simple to use indicating that they could effectively train it and that the descriptors were useful. However, many found the training being tedious, opening discussions around the need for balance between information, time, and cognitive load.
RESUMEN
Negative attitudes shape experiences with stigmatized conditions such as dementia, from affecting social relationships to influencing willingness to adopt technology. Consequently, attitudinal change has been identified as one lever to improve life for people with stigmatized conditions. Though recognized as a scaleable approach, social media has not been studied in terms of how it should best be designed or deployed to target attitudes and understanding of dementia. Through a mixed methods design with 123 undergraduate college students, we study the effect of being exposed to dementia-related media, including content produced by people with dementia. We selected undergraduate college students as the target of our intervention, as they represent the next generation that will work and interact with individuals with dementia. Our analysis describes changes over the period of two weeks in attitudes and understanding of the condition. The shifts in understanding of dementia that we found in our qualitative analysis were not captured by the instrument we selected to assess understanding of dementia. While small improvements in positive and overall attitudes were seen across all interventions and the control, we observe a different pattern with negative attitudes, where transcriptions of content produced by people with dementia significantly reduced negative attitudes. The discussion presents implications for supporting people with dementia as content producers, doing so in ways that best affect attitudes and understanding by drawing on research on cues and interactive media, and supporting students in changing their perspectives towards people with dementia.
RESUMEN
For people with visual impairments, photography is essential in identifying objects through remote sighted help and image recognition apps. This is especially the case for teachable object recognizers, where recognition models are trained on user's photos. Here, we propose real-time feedback for communicating the location of an object of interest in the camera frame. Our audio-haptic feedback is powered by a deep learning model that estimates the object center location based on its proximity to the user's hand. To evaluate our approach, we conducted a user study in the lab, where participants with visual impairments (N = 9) used our feedback to train and test their object recognizer in vanilla and cluttered environments. We found that very few photos did not include the object (2% in the vanilla and 8% in the cluttered) and the recognition performance was promising even for participants with no prior camera experience. Participants tended to trust the feedback even though they know it can be wrong. Our cluster analysis indicates that better feedback is associated with photos that include the entire object. Our results provide insights into factors that can degrade feedback and recognition performance in teachable interfaces.
RESUMEN
The installation of the 28 GHz electron cyclotron resonance ion source (ECRIS) ion implantation beamline was recently completed at the Korea Basic Science Institute. The apparatus contains a beam monitoring system and a sample holder for the ion implantation process. The new implantation system can function as a multipurpose tool since it can implant a variety of ions, ranging hydrogen to uranium, into different materials with precise control and with implantation areas as large as 1-10 mm(2). The implantation chamber was designed to measure the beam properties with a diagnostic system as well as to perform ion implantation with an in situ system including a mass spectrometer. This advanced implantation system can be employed in novel applications, including the production of a variety of new materials such as metals, polymers, and ceramics and the irradiation testing and fabrication of structural and functional materials to be used in future nuclear fusion reactors. In this investigation, the first nitrogen ion implantation experiments were conducted using the new system. The 28 GHz ECRIS implanted low-energy, multi-charged nitrogen ions into copper, zinc, and cobalt substrates, and the ion implantation depth profiles were obtained. SRIM 2013 code was used to calculate the profiles under identical conditions, and the experimental and simulation results are presented and compared in this report. The depths and ranges of the ion distributions in the experimental and simulation results agree closely and demonstrate that the new system will enable the treatment of various substrates for advanced materials research.
RESUMEN
The 28 GHz superconducting electron cyclotron resonance (ECR) ion source has been developed to produce a high current heavy ion for the linear accelerator at KBSI (Korea Basic Science Institute). The objective of this study is to generate fast neutrons with a proton target via a p(Li,n)Be reaction. The design and fabrication of the essential components of the ECR ion source, which include a superconducting magnet with a liquid helium re-condensed cryostat and a 10 kW high-power microwave, were completed. The waveguide components were connected with a plasma chamber including a gas supply system. The plasma chamber was inserted into the warm bore of the superconducting magnet. A high voltage system was also installed for the ion beam extraction. After the installation of the ECR ion source, we reported the results for ECR plasma ignition at ECRIS 2014 in Russia. Following plasma ignition, we successfully extracted multi-charged ions and obtained the first results in terms of ion beam spectra from various species. This was verified by a beam diagnostic system for a low energy beam transport system. In this article, we present the first results and report on the current status of the KBSI accelerator project.
RESUMEN
The gas cluster ion beam (GCIB) and liquid metal ion beam have been studied in the context of ion beam usage for analytical equipment in applications such as X-ray photoelectron spectroscopy and secondary ion mass spectroscopy (SIMS). In particular, small ion sources are used for the secondary ion generation and ion etching. To set the context to this study, the SIMS project has been launched to develop ion-gun based analytical equipment for the Korea Basic Science Institute. The objective of the first stage of the project is the generation of argon beams with a GCIB system [A. Kirkpatrick, Nucl. Instrum. Methods Phys. Res., Sect. B 206, 830-837 (2003)] that consists of a nozzle, skimmer, ionizer, acceleration tube, separation system, transport system, and target. The Wien filter directs the selected cluster beam to the target system by exploiting the velocity difference of the generated particles from GCIB. In this paper, we present the theoretical modeling and three-dimensional electromagnetic analysis of the Wien filter, which can separate Ar(+) 2500 clusters from Ar(+) 2400 to Ar(+) 2600 clusters with a 1-mm collimator.
RESUMEN
The Korea Basic Science Institute (KBSI) has been developing a heavy ion accelerator system to accelerate high current, multi-charge state ions produced by a 28 GHz superconducting electron cyclotron ion source. A beam analyzing system as a part of the low energy beam transport apparatus was developed to select charged particles with desirable charge states from the ion beams. The desired species of ion, which is generated and extracted from the ECR ion source including various ion particles, can be selected by 90° dipole electromagnet. Due to the non-symmetrical structure in the coil as well as the non-linear permeability of the yoke material coil, a three dimensional analysis was carried out to confirm the design parameters. In this paper, we present the experimental results obtained as result of an analysis of KBSI accelerator. The effectiveness of beam selection was confirmed during the test of the analyzing system by injecting an ion beam from an ECR ion source.