Identical clinical outcomes between neutral and classic targeted alignments after high tibial osteotomy in medial meniscus posterior root tear: a prospective randomized study.

PURPOSE: This study aimed to compare the clinical and radiographic outcomes and arthroscopic findings after high tibial osteotomy (HTO) between neutral and classic targeted coronal alignments in patients with medial meniscus posterior root tears (MMPRTs). METHODS: Ninety-eight patients with MMPRT were prospectively enrolled in the final cohort and randomized into two groups. Fifty-two patients with the targeted alignment through the Fujisawa point (60-62.5% of the entire tibial plateau width measured from the medial side) during HTO were included in group A, whereas 46 patients with the targeted alignment through the point at 50-55% of the tibial plateau width were included in group B. The clinical and radiographic outcomes and second-look arthroscopic findings were statistically compared for comprehensive assessments. RESULTS: After a mean follow-up of 37.1 months, we found no significant differences between the two groups regarding the final Lysholm (p = 0.205) and Hospital for Special Surgery scores (p = 0.084). However, we only observed significant differences between the two groups in terms of the final hip-knee-ankle angle, weight-bearing line ratio, and medial proximal tibial angle (p < 0.001). Second-look arthroscopy did not reveal a significant difference in meniscal healing rate (p = 0.786). CONCLUSIONS: Performing HTO with the aim to achieve neutral alignment leads to similar clinical outcomes in patients with MMPRT compared to classic alignment. Although subsequent research is required, the current study provides clinical evidence for the safety and efficacy of the new targeted alignment during HTO, which may avoid long-term complications associated with overcorrection when using the traditional technique.

Preoperative Leg Length Discrepancy >2 cm in the Supine Decubitus Position May Induce Compensatory Pelvic Obliquity in Patients during Total Hip Arthroplasty.

OBJECTIVES: The leg length discrepancy (LLD) in the supine decubitus position may influence the inclination angle of the acetabular component during total hip arthroplasty (THA). The relationship among LLD, pelvic obliquity, and inclination angle of the acetabular component has not been well studied. This study aimed to evaluate the relationship between LLD in supine position and changes in the inclination angle of the acetabular components during THA, and the compensatory ability of the pelvis based on LLD and inclination. METHODS: A total of 135 patients were prospectively classified into three groups according to the preoperative LLD in the supine decubitus position: the cranial type group had a positive LLD value; the fixed type group had LLD = 0; and the caudal type group had a negative LLD value. Patients in the cranial type group and caudal type group were divided into four subgroups based on the LLD value (either positive or negative): LLD >3 cm subgroup; 2 ≤ LLD ≤ 3 cm subgroup; 1 ≤ LLD < 2 cm subgroup; and LLD <1 cm subgroup. The targeted and final inclination of the acetabular component was measured intra- and postoperatively. RESULTS: The results showed a significant difference in the targeted and final inclination angles among the patients in the cranial type and the caudal type groups. In the caudal type group, increased inclination was observed in the patients of LLD >3 cm subgroup (mean 3.13°) and 2 ≤ LLD ≤ 3 cm subgroup (mean 5.17°) after THA, respectively. Decreased inclination (mean, 6.16°) was observed in 2 ≤ LLD ≤ 3 cm subgroup in the cranial type group after THA. CONCLUSIONS: Our findings revealed that in patients with discrepancy greater than 2 cm, postural pelvic obliquity imposed a remarkable influence on the inclination.

Application of 3D-bioprinted nanocellulose and cellulose derivative-based bio-inks in bone and cartilage tissue engineering.

212Three-dimensional (3D) printing is a modern, computer-aided, design-based technology that allows the layer-by-layer deposition of 3D structures. Bioprinting, a 3D printing technology, has attracted increasing attention because of its capacity to produce scaffolds for living cells with extreme precision. Along with the rapid development of 3D bioprinting technology, the innovation of bio-inks, which is recognized as the most challenging aspect of this technology, has demonstrated tremendous promise for tissue engineering and regenerative medicine. Cellulose is the most abundant polymer in nature. Various forms of cellulose, nanocellulose, and cellulose derivatives, including cellulose ethers and cellulose esters, are common bioprintable materials used to develop bio-inks in recent years, owing to their biocompatibility, biodegradability, low cost, and printability. Although various cellulose-based bio-inks have been investigated, the potential applications of nanocellulose and cellulose derivative-based bio-inks have not been fully explored. This review focuses on the physicochemical properties of nanocellulose and cellulose derivatives as well as the recent advances in bio-ink design for 3D bioprinting of bone and cartilage. In addition, the current advantages and disadvantages of these bio-inks and their prospects in 3D printing-based tissue engineering are comprehensively discussed. We hope to offer helpful information for the logical design of innovative cellulose-based materials for use in this sector in the future.

Fully arthroscopic treatment of medial Hoffa fracture associated with anterior cruciate ligament tear: case report and surgical technique.

A Hoffa fracture is a rare intra-articular injury consisting of a coronal plane fracture of one or both of the distal femoral condyles. Because of the rarity of medial Hoffa fractures, only a few reports have described this injury and its arthroscopic management. In this article, we present a rare case involving a 32-year-old man with a displaced medial Hoffa fracture associated with a proximal anterior cruciate ligament tear. He was treated by a single-stage fully all-inside arthroscopic technique. Arthroscopic-assisted internal fixation ensured fragment stability and enabled us to visualize the fracture reduction, monitor the screw insertion, and reconstruct the anterior cruciate ligament tear at the same time. This technique is a novel but demanding treatment method for medial Hoffa fractures and is particularly useful for properly selected patients with associated intra-articular knee injuries.