Immediate implant placement with soft tissue grafting and an ultra-translucent zirconia crown. Replacement of a primary tooth in the esthetic zone

OBJECTIVES: The present case report describes the atraumatic extraction of a primary maxillary right canine followed by immediate implant placement with a customized zirconia abutment and monolithic ultra-translucent zirconia (5Y-PSZ) crown. CLINICAL CONSIDERATIONS: A 31-year-old patient presented to the clinic with the primary concern of mobility and gingival inflammation around the maxillary right canine. After clinical evaluation, the tooth was found to be a primary retained tooth that presented grade 3 mobility and gingival inflammation. Atraumatic tooth extraction was performed, followed by immediate implant placement of a screw-retained provisional restoration with the use of a surgical guide. The soft tissue was contoured until ideal architecture was obtained. The final restoration included a customized zirconia and titanium abutment and a characterized implant-supported monolithic 5Y-PSZ crown. CONCLUSIONS: Well-planned surgical and restorative procedures including atraumatic extraction, 3D implant planning for surgical guide fabrication, implant placement, and a customized zirconia abutment with a monolithic 5Y-PSZ crown can achieve high esthetic results in replacing a primary tooth in the esthetic zone.

Fracture Resistance of Chairside CAD/CAM Molar Crowns Fabricated with Different Lithium Disilicate Ceramic Materials

PURPOSE: To compare the fracture resistance of five different groups of chairside CAD/CAM molar crowns fabricated from various lithium disilicate ceramic materials (LDC): one conventional precrystallized CAD/CAM LDC, two novel precrystallized LDCs, and one fully crystallized LDC tested both with and without optional sintering. MATERIALS AND METHODS: A total of 60 chairside CAD/CAM lithium disilicate molar crowns (n = 12 per group) with 1.5-mm occlusal thickness and a 1.0-mm chamfer finish were designed and fabricated with a chairside CAD/CAM system (CEREC, Dentsply Sirona). The restorations were divided into five groups: (1) IPS e.max CAD; (2) Amber Mill; (3) Straumann n!ce; (4) Straumann n!ce with optional sintering; and (5) Supreme CAD. Restorations were cemented using conventional resin luting cement and primer system to 3D-printed resin dies. Bonded restorations were loaded for 100,000 cycles with 275-N force, and the load at break (LB) and peak load (PL) until fracture were measured. SEM images of fracture surfaces on the printed dies were obtained. RESULTS: Fracture resistance was significantly different depending on the material. Supreme CAD showed the highest fracture resistance (LB: 1,557.2 N; PL: 1,785.8 N), followed by Amber Mill (LB: 1,393.0 N; PL: 1,604.2 N) and IPS e.max CAD (LB: 1,315.7 N; PL: 1,461.9 N). Straumann n!ce without (LB: 862.4 N; PL: 942.9 N) and with the optional sintering (LB: 490.4 N; PL: 541.0 N) showed significantly lower fracture resistance than the others. CONCLUSION: The fracture resistance of chairside CAD/CAM lithium disilicate molar crowns varied depending on the material, and the novel materials did not perform as well as the conventional equivalents. Fully crystallized lithium disilicate ceramic block materials showed lower fracture resistance than precrystallized counterparts and should be used with caution in the clinic, especially with optional sintering.

Fracture resistance of zirconia surveyed crowns with four different occlusal rest seat designs.

PURPOSE: To determine the fracture resistance of chairside computer-aided design and computer-aided manufacturing (CAD-CAM) zirconia surveyed crowns for a mandibular first molar without occlusal rest and with four different rest seat designs. MATERIALS AND METHODS: Seventy CAD-CAM zirconia 4Y-PSZ (IPS e.max ZirCAD MT for CEREC A1, C15, Ivoclar Vivadent) crowns (14 specimens/group) were designed and fabricated with a dental chairside CAD-CAM system (CEREC PrimeScan, and CEREC MCXL Dentsply Sirona). The restorations were divided into groups according to the following rest seat designs: (1) Surveyed crown without rest seat, (2) surveyed crowns with disto-occlusal rest seat, (3) surveyed crowns with disto-occlusal extended rest seat, (4) surveyed crowns with interproximal rest seat, and (5) continuous rest seat. Crowns were treated with a primer system (Monobond Plus, Ivoclar Vivadent) and cemented using resin luting cement (Multilink Automix, Ivoclar Vivadent) to resin-printed dies (Grey Resin V4, FormLabs). Subsequently, the crowns were subjected to 200,000 load cycles at 1 Hz with 20 N force and then loaded with a steel indenter until fracture. The test results were analyzed with one-way Analysis of Variance (ANOVA) and HSD Tukey post-Hoc test. RESULTS: The mean fracture resistance of surveyed crowns without and with different rest seats was significantly different from each other. Surveyed crowns with no rest seat displayed the highest resistance (4238 N) followed by crowns with continuous rest seat (3601 N), crowns with disto-occlusal extended rest seat (3283 N), and crowns with disto-occlusal rest seat (3257 N). Crowns with interproximal rest seat displayed the lowest fracture resistance (2723 N). CONCLUSIONS: Surveyed crowns without rest seats had a higher fracture resistance than crowns with rest seats Surveyed crowns with interproximal rest seats presented the lowest fracture resistance among all rest seat designs. Crowns with disto-occlusal rest seats, disto-occlusal extended rest seats, and continuous rest seats displayed similar fracture resistance.

Soft Tissue Grafting Procedures before Restorations in the Esthetic Zone: A Minimally Invasive Interdisciplinary Case Report.

An esthetically pleasing smile is a valuable aspect of physical appearance and plays a significant role in social interaction. Achieving the perfect balance between extraoral and intraoral tissues is essential for a harmonious and attractive smile. However, certain intraoral deficiencies, such as non-carious cervical lesions and gingival recession, can severely compromise the overall aesthetics, particularly in the anterior zone. Addressing such conditions requires careful planning and meticulous execution of both surgical and restorative procedures. This interdisciplinary clinical report presents a complex case of a patient with esthetic complaints related to asymmetric anterior gingival architecture and severely discolored and eroded maxillary anterior teeth. The patient was treated using a combination of minimally invasive ceramic veneers and plastic mucogingival surgery, resulting in a successful outcome. The report emphasizes the potential of this approach in achieving optimal esthetic results in challenging cases, highlighting the importance of an interdisciplinary team approach in achieving a harmonious balance between dental and soft tissue aesthetics.

Natural Bioactive Epigallocatechin-Gallate Promote Bond Strength and Differentiation of Odontoblast-like Cells.

The (-)-Epigallocatechin-gallate (EGCG) metabolite is a natural polyphenol derived from green tea and is associated with antioxidant, biocompatible, and anti-inflammatory effects. OBJECTIVE: To evaluate the effects of EGCG to promote the odontoblast-like cells differentiated from human dental pulp stem cells (hDPSCs); the antimicrobial effects on Escherichia coli, Streptococcus mutans, and Staphylococcus aureus; and improve the adhesion on enamel and dentin by shear bond strength (SBS) and the adhesive remnant index (ARI). MATERIAL AND METHODS: hDSPCs were isolated from pulp tissue and immunologically characterized. EEGC dose-response viability was calculated by MTT assay. Odontoblast-like cells were differentiated from hDPSCs and tested for mineral deposition activity by alizarin red, Von Kossa, and collagen/vimentin staining. Antimicrobial assays were performed in the microdilution test. Demineralization of enamel and dentin in teeth was performed, and the adhesion was conducted by incorporating EGCG in an adhesive system and testing with SBS-ARI. The data were analyzed with normalized Shapiro-Wilks test and ANOVA post hoc Tukey test. RESULTS: The hDPSCs were positive to CD105, CD90, and vimentin and negative to CD34. EGCG (3.12 µg/mL) accelerated the differentiation of odontoblast-like cells. Streptococcus mutans exhibited the highest susceptibility < Staphylococcus aureus < Escherichia coli. EGCG increased (p < 0.05) the dentin adhesion, and cohesive failure was the most frequent. CONCLUSION: (-)-Epigallocatechin-gallate is nontoxic, promotes differentiation into odontoblast-like cells, possesses an antibacterial effect, and increases dentin adhesion.

Clinical Efficacy of Biomimetic Bioactive Biomaterials for Dental Pulp Capping: A Systematic Review and Meta-Analysis.

Recently, biomimetic bioactive biomaterials have been introduced to the market for dental pulp capping. This systematic review and meta-analysis aimed to determine any variation between the effect of using TheraCal LC and other bioactive biomaterials for pulp capping is different, as measured by dentin increment and clinical success. The risk of bias was assessed using the Risk of Bias 2 and Newcastle−Ottawa tools for randomized clinical trials and observational studies. A search for relevant articles was performed on five databases. Additionally, the quality of the included studies was assessed using the Grading of Recommendations Assessment, Development, and Evaluation (GRADE) criteria. A summary of individual studies and a meta-analysis were performed. The odds ratio of data from clinical success was combined using a random-effects meta-analysis. The meta-analysis results showed homogeneity between the studies (I2 = 0%). They revealed that the clinical success showed no differences between the patients who received TheraCal LC, light-cured calcium silicate-based biomimetic biomaterial, for dental pulp capping or the comparator biomaterials (p > 0.5). However, the certainty of the evidence was low to moderate due to the risk of bias in the included studies.

Fracture Resistance of Chairside CAD/CAM Molar Crowns Fabricated with Different Lithium Disilicate Ceramic Materials.

PURPOSE: To compare the fracture resistance of five different groups of chairside CAD/CAM molar crowns fabricated from various lithium disilicate ceramic materials (LDC): one conventional precrystallized CAD/CAM LDC, two novel precrystallized LDCs, and one fully crystallized LDC tested both with and without optional sintering. MATERIALS AND METHODS: A total of 60 chairside CAD/CAM lithium disilicate molar crowns (n = 12 per group) with 1.5-mm occlusal thickness and a 1.0-mm chamfer finish were designed and fabricated with a chairside CAD/CAM system (CEREC, Dentsply Sirona). The restorations were divided into five groups: (1) IPS e.max CAD; (2) Amber Mill; (3) Straumann n!ce; (4) Straumann n!ce with optional sintering; and (5) Supreme CAD. Restorations were cemented using conventional resin luting cement and primer system to 3D-printed resin dies. Bonded restorations were loaded for 100,000 cycles with 275-N force, and the load at break (LB) and peak load (PL) until fracture were measured. SEM images of fracture surfaces on the printed dies were obtained. RESULTS: Fracture resistance was significantly different depending on the material. Supreme CAD showed the highest fracture resistance (LB: 1,557.2 N; PL: 1,785.8 N), followed by Amber Mill (LB: 1,393.0 N; PL: 1,604.2 N) and IPS e.max CAD (LB: 1,315.7 N; PL: 1,461.9 N). Straumann n!ce without (LB: 862.4 N; PL: 942.9 N) and with the optional sintering (LB: 490.4 N; PL: 541.0 N) showed significantly lower fracture resistance than the others. CONCLUSION: The fracture resistance of chairside CAD/CAM lithium disilicate molar crowns varied depending on the material, and the novel materials did not perform as well as the conventional equivalents. Fully crystallized lithium disilicate ceramic block materials showed lower fracture resistance than precrystallized counterparts and should be used with caution in the clinic, especially with optional sintering.

Effect of Different Solutions on the Colour Stability of Nanoparticles or Fibre Reinforced PMMA.

This study aimed to evaluate the colour stability of polymethyl methacrylate (PMMA) denture base reinforced with ZrO2 nanoparticles, E-glass fibres, and TiO2 nanoparticles at various concentrations over 180-day storage in Steradent™ (STD) denture cleaner or coffee (CF). A total of 130 disc-shaped specimens were fabricated at various filler concentrations and divided into four main groups to measure the colour changes. Groups Z, T, and E consisted of PMMA reinforced with ZrO2 nanoparticles, TiO2 nanoparticles, or E-glass fibre, respectively, while Group C consisted of PMMA specimens without filler served as the control group (n = 10). The three reinforced groups were further subdivided according to the filler content (n = 10) added to the PMMA (1.5%, 3.0%, 5.0%, and 7.0% wt.%). Half of the specimens were stored in STD, while the other half was stored in CF for 180 days. A Minolta Chroma Meter was used to measure the colour changes (ΔE) at 7, 30, 90 and then 180 days. The results were assessed using two-way repeated-measures analysis of variance (RM-ANOVA) along with Bonferroni post hoc tests at a p ≤ 0.05 significance level. Significant different colour changes (ΔΕ) were observed between all tested groups and across different time points. TiO2-reinforced PMMA in STD/CF showed the lowest colour stability, while the E-glass fibre-reinforced PMMA in STD/CF showed the highest colour stability. Furthermore, coffee appeared to have the greatest impact on the colour change in comparison to the SteradentTM. The results indicated that the filler type and concentration, type of solution, and length of storage all affected the colour stability of the tested specimens.

Novel translucent monolithic zirconia fixed restorations in the esthetic zone.

Novel translucent monolithic zirconia has improved optical properties, and it may fulfill patient's esthetic demands and overcome the chipping risk of bilayer metal-ceramic restorations. New zirconia's microstructures allow us to mimic natural teeth.

Color stability of fully- and pre-crystalized chair-side CAD-CAM lithium disilicate restorations after required and additional sintering processes.

PURPOSE: The aim of this study was to investigate shade changes in fully- and pre-crystalized CAD-CAM lithium disilicate crowns after the required and additional firing processes. MATERIALS AND METHODS: One hundred and five crowns of shade A1 with high translucency were milled out of CAD-CAM lithium disilicate blocks and categorized as follows (n = 15): (1) restorations fabricated from Straumann n!ce with no additional sintering process; (2) restorations fabricated from Straumann n!ce with one additional sintering process; (3) restorations fabricated from Straumann n!ce with two additional sintering processes; (4) restorations fabricated from Amber Mill with one sintering process; (5) restorations fabricated from Amber Mill with two sintering processes; (6) restorations fabricated from IPS e.max CAD with one sintering process; (7) restorations fabricated from IPS e.max CAD with two sintering processes. All restorations were evaluated with a color imaging spectrophotometer. RESULTS: All restorations presented some color alteration from the original shade both after a single and after two firing processes. CONCLUSION: The required and additional sintering processes for restorations fabricated with chairside CAD-CAM lithium disilicate blocks cause an alteration of the original shade selected. Shade A1 high translucency restorations tend to change to a more yellowish B1 shade after a sintering process.

Behaviour of PMMA Resin Composites Incorporated with Nanoparticles or Fibre following Prolonged Water Storage.

When PMMA denture base acrylics are exposed to oral environments for prolonged periods, the denture base absorbs water, which has a negative influence on the denture material and the degree to which the denture base will be clinically effective. This study assessed the water sorption, desorption, and hygroscopic expansion processes within PMMA denture-base resins reinforced with nanoparticles or fibre in comparison to the non-reinforced PMMA. The surfaces of the fillers were modified using a silane coupling agent (y-MPS) before mixing with PMMA. Group C consisted of specimens of pure PMMA whereas groups Z, T, and E consisted of PMMA specimens reinforced with ZrO2, TiO2 nanoparticles, or E-glass fibre, respectively. The reinforced groups were subdivided into four subgroups according to the percentage filler added to the PMMA resin by weight (1.5%, 3.0%, 5.0%, or 7.0%). Five specimens in disc shape (25 ± 1 mm × 2.0 ± 0.2 mm) were tested for each group. To assess water sorption and hygroscopic expansion, specimens from each group were individually immersed in water at 37 ± 1 °C for 180 days. The samples were then desorbed for 28 days at 37 ± 1 °C, to measure solubility. Water sorption and solubility were calculated using an electronic balance in accordance with ISO Standard 20795-1, and hygroscopic expansion was measured using a laser micrometre. Statistical analysis was undertaken at a p ≤ 0.05 significance level using a one-way ANOVA followed by Tukey post-hoc tests. The results demonstrated that the values of sorption (Wsp), mass sorption (Ms%), and % expansion within the tested groups reached equilibrium within 180 days. A noticeable difference was observed in groups Z and E for (Wsp)/(Ms%) compared to the Group C, but this was not significant. However, the difference between Group C and Group T for these measurements was significant. Non-significant differences also existed between each respective reinforced group and the control group in terms of hygroscopic expansion % values. During the 28-day desorption period, there were no differences in the values of solubility (Wsl)/mass desorption (Md%) between Group C and each of the reinforced tested groups. The findings indicate that the inclusion of ZrO2 nanoparticles or E-glass fibres does not increase the water solubility/sorption of the PMMA. However, modifying the PMMA with TiO2 did significantly increase the water sorption level.

Esthetic outcome for implant therapy of a maxillary lateral incisor using prefabricated titanium and customized zirconia abutments: 4-year clinical reports.

The reported clinical scenarios presented two patients, one managed with a prefabricated abutment and the other with a customized abutment, and both patients were pleased with the outcome. However, from a professional viewpoint, the esthetic outcome using the custom zirconia abutment was superior to that using the prefabricated titanium abutment.

A customized metal guide for controllable modification of anterior teeth contour prior to minimally invasive preparation.

OBJECTIVE: Optimal tooth reduction is a key requirement for aesthetics, function, and the longevity of fixed restorations. Research has demonstrated that controlled and conservative tooth preparation is crucial for the long-term success of adhesive restorations. Different techniques of fabricating reduction guides have been previously reported in literature. The present technical note describes the fabrication technique and clinical application of a customized metal preparation reduction guide. MATERIAL AND METHOD: Patient presented with tilted maxillary left central incisor. The flared-out part of the tooth was modified prior to veneer restoration preparation. Resin pattern reduction guide was fabricated on the diagnostic cast with a window on the tilted mesial portion of the tooth. After intraoral evaluation, resin pattern guide was casted. Metal reduction guide was place intraorally and reduction was provided on the exposed surface of the tooth. After the removal of the tilted portion, a harmonious arch form allowed the clinician to provide adequate evaluation and preparation for veneer restorations. RESULTS: The device demonstrated good practical value, allowing for selective and controlled reduction of tooth structure, and definitive protection of adjacent tooth surfaces from iatrogenic damage. The clinical outcome successfully addressed the patient's restorative and aesthetic needs, and the veneer was stable 2 years postoperatively. CONCLUSION: Use of a metal guide assists clinicians to provide a more predictable reduction of a desired tooth surface, while decreasing the risk of compromising the other/adjacent tooth surfaces.

Relationships between Flexural and Bonding Properties, Marginal Adaptation, and Polymerization Shrinkage in Flowable Composite Restorations for Dental Application.

To evaluate the flexural and bonding properties, marginal adaptation, and polymerization shrinkage in flowable composite restorations and their relationships, four new generation flowable composites, one conventional, and one bulk-fill flowable composite were used in this study. Flexural properties of the composites and shear bond strength to enamel and dentin for flowable restorations were measured immediately and 24 h after polymerization. Marginal adaptation, polymerization shrinkage, and stress were also investigated immediately after polymerization. The flexural properties, and bond strength of the flowable composites to enamel and dentin were much lower immediately after polymerization than at 24 h, regardless of the type of the composite. Polymerization shrinkage and stress varied depending on the material, and bulk-fill flowable composite showed much lower values than the others. The marginal adaptation and polymerization shrinkage of the composites appeared to have a much stronger correlation with a shear bond strength to dentin than to enamel. The weak mechanical properties and bond strengths of flowable composites in the early stage after polymerization must be taken into account when using them in the clinic. In addition, clinicians should be aware that polymerization shrinkage of flowable composites can still lead to the formation of gaps and failure of adaptation to the cavity regardless of the type of composite.

Clinical decision-making regarding endodontic therapy vs extraction and implant-assisted replacement: a systematic review and meta-analysis.

Clinical decision-making regarding retention and treatment vs extraction and replacement of teeth can be a significant challenge. This systematic review and meta-analysis aimed to assess decision-making in clinical practice related to the retention and endodontic treatment of natural dentition vs extraction and replacement with implant-assisted restorations. The PubMed/MEDLINE, Scopus, Web of Science, and Education Resources Information Center (ERIC) databases were comprehensively searched for studies published through May 31, 2019. All randomized controlled trials and cohort studies that assessed the effect of endodontic treatment/retreatment and implant treatment were included. Primary outcomes included success, survival, and failure rates. Meta-analysis software was used for data analysis. Of 1550 identified articles, 5 were eligible for qualitative and quantitative analyses. All 5 of the included studies reported that both therapies are viable and predictable treatment options. The meta-analysis showed no significant difference between therapies when survival rates were considered to be successes, while a significant difference was found in favor of endodontic therapy when survival rates were considered to be failures. The available evidence suggests that both therapies have approximately similar outcomes, but endodontic therapy provides moderately better outcomes. Endodontic therapy should be considered the first option when possible.

Emotional, behavioral, and social effects of anterior tooth loss: a cross-sectional study / Efeitos emocionais, comportamentais e sociais da perda dentária anterior: um estudo tranversal

Objective: The study aims to evaluate the emotional, behavioural, and social effects of single or multiple anterior tooth loss. It also compares the effectiveness of the removable and fixed prosthesis to address the impact of anterior tooth loss. Material and Methods: The study was carried out on 70 subjects who presented to the Department of Prosthetic Dental Sciences. A questionnaire was distributed and the data were statistically analyzed using SPSS version 18.0 and values less than 0.05 % were considered statistically significant. Results: The participant's difficulty to accept loss of their anterior tooth, embarrassment and confidence were changed significantly after wearing the prosthesis (P< 0.05). Moreover, fixed partial denture had more effect than removal partial denture. It was claimed by 62.9% of the participants that they were not prepared for the effect of tooth loss and 47.1% of them thought that a prior explanation from the dentist would have helped them overcome their fear of losing their teeth. Conclusion: The maximum impact of anterior tooth loss was felt on confidence followed by embarrassment. The participants felt more comfortable after wearing their prosthesis. Fixed partial denture had more effect than removable partial denture.(AU)

Objetivo: O estudo visa avaliar os efeitos emocionais, comportamentais e sociais da perda dentária anterior unitária ou múltipla. Ele também compara a eficácia da protese removível e da fixa para lidar com o impacto da perda dentária anterior. Material e Métodos: O estudo foi realizado em 70 indivíduos que se apresentaram ao Department of Prosthetic Dental Sciences. Foi distribuído um questionário e os dados analisados estatisticamente no SPSS versão 18.0 e valores inferiores a 0,05% foram considerados estatisticamente significativos. Resultados: A dificuldade do participante em aceitar a perda de seu dente anterior, constrangimento e confiança mudaram significativamente após usar a prótese (P <0,05). Além disso, a prótese parcial fixa teve mais efeito do que a prótese parcial removível. Foi alegado por 62,9% dos participantes que não estavam preparados para o efeito da perda dentária e 47,1% deles achavam que uma explicação prévia do cirurgião-dentista os teria ajudado a superar o medo de perder os dentes. Conclusão: O impacto máximo da perda dentária anterior foi sentido na confiança, seguido de constrangimento. Os participantes se sentiram mais confortáveis após o uso de suas próteses. A prótese parcial fixa teve mais efeito do que a prótese parcial removível (AU)

Conservative approach for management of fractured maxillary central incisors in young adults.

Ceramic restorations could be an acceptable treatment choice for fractured central incisors. A successful esthetic and conservative result to restore damaged anterior teeth can be obtained through proper evaluation, diagnostic wax-up, guided minimal preparations, ceramic selection, and bonding protocols. Handcrafted glass-based restorations can mimic contours and shape of natural teeth.

Combining a single implant and a veneer restoration in the esthetic zone.

OBJECTIVE: The combination of partial edentulism and a worn anterior tooth in the esthetic zone can be a challenge for the dentist. This clinical situation requires extensive knowledge of soft and hard tissue management, surgical planning and execution for implant therapy, and conservative tooth preparation with ideal bonding protocols for the tooth-supported prosthesis. Moreover, an optimal selection of the final restorative materials is imperative to manage occlusal forces and fulfill the patient's esthetic demands. MATERIALS AND METHODS: The patient presented with partial edentulism on site 11, a worn incisal edge, and facial defects on tooth 21. Minimally invasive implant therapy for site 11 was performed with a papilla-sparing flap design that only included the edentulous site, and the soft tissue contouring was started for an immediate provisional restoration. A suturing technique was executed that aimed at maintaining an interproximal papilla. Conservative veneer preparation was performed on tooth 21 in order to bond the restoration to the enamel structure. Final restorations included a custom abutment with a lithium disilicate fused to zirconia crown for the implant on site 11 and a lithium disilicate veneer on tooth 21. CONCLUSIONS: A well-planned single implant and a ceramic veneer restoration was able to fulfill the patient's esthetic expectations. The selection of materials for the final restoration was crucial to manage the occlusal forces and to mimic the shade and shape of the adjacent teeth.

Chair-side CAD/CAM fabrication of a single-retainer resin bonded fixed dental prosthesis: a case report.

This clinical report describes designing and fabricating a single-retainer resin-bonded fixed dental prosthesis with a chair-side computer-aided design/computer-aided manufacturing system. The whole procedure, from tooth extraction to final placement of the prosthesis, was completed in one day, and a single clinic visit. No clinical complications were found at the 2-year follow-up after placement of the restoration, and satisfactory functional and esthetic results were achieved.

Digitally Fabricated Immediate Complete Dentures: Case Reports of Milled and Printed Dentures.

Milling complete dentures is becoming a popular option for clinicians because subtractive technology can make the fabrication of high-quality dentures faster and easier. Additive technology is one of the newest techniques for making complete dentures, and its primary advantage is that a printer is more financially accessible than a milling machine. Printing and milling technologies as methods for denture fabrication have similar steps and time frames for their processes. The production of immediate complete dentures also follows similar procedures for both systems. The aim of this article is to compare subtractive and additive technologies for the manufacture of immediate complete dentures and to present two case reports.