Iridium-Based Selective Emitters for Thermophotovoltaic Applications.

The long-term operation of refractory-metal-based metamaterials is crucial for applications such as thermophotovoltaics. The metamaterials based on refractory metals like W, Mo, Ta, Nb, and Re fail primarily by oxidation. Here, the use of the noble metal Ir is proposed, which is stable to oxidation and has optical properties comparable to gold. The thermal endurance of Ir in a 3-layer-system, consisting of HfO2 /Ir/HfO2 , by performing annealing experiments up to 1240 °C in a pressure range from 2 × 10-6  mbar to 1 bar, is demonstrated. The Ir layer shows no oxidation in a vacuum and inert gas atmosphere. At temperatures above 1100 °C, the Ir layer starts to agglomerate due to the degradation of the confining HfO2 layers. An in situ X-ray diffraction experimental comparison between 1D multilayered Ir/HfO2 and W/HfO2 selective emitters annealed at 1000 °C, 2 × 10-6  mbar, over 100 h, confirms oxidation stability of Ir while W multilayers gradually disappear. The results of this work show that W-based metamaterials are not long-term stable even at 1000 °C. However, the oxidation resistance of Ir can be leveraged for refractory plasmonic metamaterials, such as selective emitters in thermophotovoltaic systems with strong suppression of long wavelength radiation.

Transformation Kinetics of LiBH4-MgH2 for Hydrogen Storage.

The reactive hydride composite (RHC) LiBH4-MgH2 is regarded as one of the most promising materials for hydrogen storage. Its extensive application is so far limited by its poor dehydrogenation kinetics, due to the hampered nucleation and growth process of MgB2. Nevertheless, the poor kinetics can be improved by additives. This work studied the growth process of MgB2 with varying contents of 3TiCl3·AlCl3 as an additive, and combined kinetic measurements, X-ray diffraction (XRD), and advanced transmission electron microscopy (TEM) to develop a structural understanding. It was found that the formation of MgB2 preferentially occurs on TiB2 nanoparticles. The major reason for this is that the elastic strain energy density can be reduced to ~4.7 × 107 J/m3 by creating an interface between MgB2 and TiB2, as opposed to ~2.9 × 108 J/m3 at the original interface between MgB2 and Mg. The kinetics of the MgB2 growth was modeled by the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation, describing the kinetics better than other kinetic models. It is suggested that the MgB2 growth rate-controlling step is changed from interface- to diffusion-controlled when the nucleation center changes from Mg to TiB2. This transition is also reflected in the change of the MgB2 morphology from bar- to platelet-like. Based on our observations, we suggest that an additive content between 2.5 and 5 mol% 3TiCl3·AlCl3 results in the best enhancement of the dehydrogenation kinetics.

Transient Surface Photovoltage Spectroscopy of (NH4)2Mo3S13/WSe2 Thin-Film Photocathodes for Photoelectrochemical Hydrogen Evolution.

Hydrogen produced from solar energy has the potential to replace petroleum in the future. To this respect, there is a need in the abandoned and efficient materials that can continuously split water molecules using solar energy. In this report, an ammonium thiomolybdate (ATM: (NH4)2Mo3S13) is evaluated as a p-type semiconductor film photocathode for hydrogen evolution reaction. The ATM thin films are prepared by spin-coating on fluorine-doped tin oxide substrates, and their structural, morphological, optical, photoelectrical, and photoelectrochemical (PEC) properties are studied. Transient surface photovoltage (TSPV) spectroscopy and spectroscopic ellipsometry indicate the band gap Eg = 1.9 eV for the ATM thin films. Furthermore, the photovoltage of the ATM thin films measured by TSPV is correlated to the photocurrents measured by the PEC characterization that can be used to evaluate the material potential for hydrogen generation. The films exhibit a low photocurrent density of 46 µA cm-2 at 0 VRHE. However, its combination with WSe2 thin-film photocathodes results in a significant increase in photocurrent density up to 4.6 mA cm-2 at 0 VRHE (100 times). The reason for such a strong charge carrier transfer effect for ATM/WSe2 heterojunction photocathodes is studied by TSPV spectroscopy that allows a comprehensive evaluation of potential photovoltaic materials toward PEC hydrogen production. Furthermore, the photovoltage generated by a WSe2 thin film is 30 times lower than that of its single crystal, which indicates that the quality of WSe2 thin films should be improved for faster PEC hydrogen evolution.

A comprehensive study on lithium-based reactive hydride composite (Li-RHC) as a reversible solid-state hydrogen storage system toward potential mobile applications.

Reversible solid-state hydrogen storage is one of the key technologies toward pollutant-free and sustainable energy conversion. The composite system LiBH4-MgH2 can reversibly store hydrogen with a gravimetric capacity of 13 wt%. However, its dehydrogenation/hydrogenation kinetics is extremely sluggish (∼40 h) which hinders its usage for commercial applications. In this work, the kinetics of this composite system is significantly enhanced (∼96%) by adding a small amount of NbF5. The catalytic effect of NbF5 on the dehydrogenation/hydrogenation process of LiBH4-MgH2 is systematically investigated using a broad range of experimental techniques such as in situ synchrotron radiation X-ray powder diffraction (in situ SR-XPD), X-ray absorption spectroscopy (XAS), anomalous small angle X-ray scattering (ASAXS), and ultra/small-angle neutron scattering (USANS/SANS). The obtained results are utilized to develop a model that explains the catalytic function of NbF5 in hydrogen release and uptake in the LiBH4-MgH2 composite system.

Using the Emission of Muonic X-rays as a Spectroscopic Tool for the Investigation of the Local Chemistry of Elements.

There are several techniques providing quantitative elemental analysis, but very few capable of identifying both the concentration and chemical state of elements. This study presents a systematic investigation of the properties of the X-rays emitted after the atomic capture of negatively charged muons. The probability rates of the muonic transitions possess sensitivity to the electronic structure of materials, thus making the muonic X-ray Emission Spectroscopy complementary to the X-ray Absorption and Emission techniques for the study of the chemistry of elements, and able of unparalleled analysis in case of elements bearing low atomic numbers. This qualitative method is applied to the characterization of light elements-based, energy-relevant materials involved in the reaction of hydrogen desorption from the reactive hydride composite Ca(BH4)2-Mg2NiH4. The origin of the influence of the band-structure on the muonic atom is discussed and the observed effects are attributed to the contribution of the electronic structure to the screening and to the momentum distribution in the muon cascade.

Enhanced Stability of Li-RHC Embedded in an Adaptive TPX™ Polymer Scaffold.

In this work, the possibility of creating a polymer-based adaptive scaffold for improving the hydrogen storage properties of the system 2LiH+MgB2+7.5(3TiCl3·AlCl3) was studied. Because of its chemical stability toward the hydrogen storage material, poly(4-methyl-1-pentene) or in-short TPXTM was chosen as the candidate for the scaffolding structure. The composite system was obtained after ball milling of 2LiH+MgB2+7.5(3TiCl3·AlCl3) and a solution of TPXTM in cyclohexane. The investigations carried out over the span of ten hydrogenation/de-hydrogenation cycles indicate that the material containing TPXTM possesses a higher degree of hydrogen storage stability.

Improved kinetic behaviour of Mg(NH2)2-2LiH doped with nanostructured K-modified-LixTiyOz for hydrogen storage.

The system Mg(NH2)2 + 2LiH is considered as an interesting solid-state hydrogen storage material owing to its low thermodynamic stability of ca. 40 kJ/mol H2 and high gravimetric hydrogen capacity of 5.6 wt.%. However, high kinetic barriers lead to slow absorption/desorption rates even at relatively high temperatures (>180 °C). In this work, we investigate the effects of the addition of K-modified LixTiyOz on the absorption/desorption behaviour of the Mg(NH2)2 + 2LiH system. In comparison with the pristine Mg(NH2)2 + 2LiH, the system containing a tiny amount of nanostructured K-modified LixTiyOz shows enhanced absorption/desorption behaviour. The doped material presents a sensibly reduced (∼30 °C) desorption onset temperature, notably shorter hydrogen absorption/desorption times and reversible hydrogen capacity of about 3 wt.% H2 upon cycling. Studies on the absorption/desorption processes and micro/nanostructural characterizations of the Mg(NH2)2 + 2LiH + K-modified LixTiyOz system hint to the fact that the presence of in situ formed nanostructure K2TiO3 is the main responsible for the observed improved kinetic behaviour.

Charge Transfer in c-Si(n++)/TiO2(ALD) at the Amorphous/Anatase Transition: A Transient Surface Photovoltage Spectroscopy Study.

Electronic properties and charge transfer processes were studied in an n-Si(n++)/TiO2(ALD) system at an amorphous TiO2/anatase transition by transient surface photovoltage spectroscopy at constant photon flux. The TiO2 layers were deposited by atomic layer deposition (ALD) onto highly doped silicon (c-Si(n++)), and the phase composition of the TiO2 layers changed with increasing thickness from amorphous to the anatase polymorph as anatase crystallites started to grow at the surface. Depending on phase composition, the band gap of TiO2 correlated with the characteristic energy of exponential tails. In most cases, photogenerated electrons were separated toward the back contact. For photogeneration in c-Si(n++), electron back transfer was limited by Auger recombination with holes in the surface space charge region of c-Si(n++), and by electron transfer across the interface, either via exponentially distributed states near the conduction band edge of amorphous TiO2 or via distance-dependent recombination with holes trapped in anatase. For photogeneration in TiO2, electron back transfer was limited by trapping in TiO2. Under strong light absorption in amorphous TiO2 with anatase crystallites on top, electrons were preferentially separated toward the TiO2 surface.

Insights into the Rb-Mg-N-H System: an Ordered Mixed Amide/Imide Phase and a Disordered Amide/Hydride Solid Solution.

The crystal structure of a mixed amide-imide phase, RbMgND2ND, has been solved in the orthorhombic space group Pnma ( a = 9.55256(31), b = 3.70772(11) and c = 10.08308(32) Å). A new metal amide-hydride solid solution, Rb(NH2) xH(1- x), has been isolated and characterized in the entire compositional range. The profound analogies, as well as the subtle differences, with the crystal chemistry of KMgND2ND and K(NH2) xH1- x are thoroughly discussed. This approach suggests that the comparable performances obtained using K- and Rb-based additives for the Mg(NH2)2- 2LiH and 2LiN H2-MgH2 hydrogen storage systems are likely to depend on the structural similarities of possible reaction products and intermediates.

Li2 NH-LiBH4 : a Complex Hydride with Near Ambient Hydrogen Adsorption and Fast Lithium Ion Conduction.

Complex hydrides have played important roles in energy storage area. Here a complex hydride made of Li2 NH and LiBH4 was synthesized, which has a structure tentatively indexed using an orthorhombic cell with a space group of Pna21 and lattice parameters of a=10.121, b=6.997, and c=11.457 Å. The Li2 NH-LiBH4 sample (in a molar ratio of 1:1) shows excellent hydrogenation kinetics, starting to absorb H2 at 310 K, which is more than 100 K lower than that of pristine Li2 NH. Furthermore, the Li+ ion conductivity of the Li2 NH-LiBH4 sample is about 1.0×10-5  S cm-1 at room temperature, and is higher than that of either Li2 NH or LiBH4 at 373 K. Those unique properties of the Li2 NH-LiBH4 complex render it a promising candidate for hydrogen storage and Li ion conduction.

Kinetic alteration of the 6Mg(NH2)2-9LiH-LiBH4 system by co-adding YCl3 and Li3N.

The 6Mg(NH2)2-9LiH-LiBH4 composite system has a maximum reversible hydrogen content of 4.2 wt% and a predicted dehydrogenation temperature of about 64 °C at 1 bar of H2. However, the existence of severe kinetic barriers precludes the occurrence of de/re-hydrogenation processes at such a low temperature (H. Cao, G. Wu, Y. Zhang, Z. Xiong, J. Qiu and P. Chen, J. Mater. Chem. A, 2014, 2, 15816-15822). In this work, Li3N and YCl3 have been chosen as co-additives for this system. These additives increase the hydrogen storage capacity and hasten the de/re-hydrogenation kinetics: a hydrogen uptake of 4.2 wt% of H2 was achieved in only 8 min under isothermal conditions at 180 °C and 85 bar of H2 pressure. The re-hydrogenation temperature, necessary for a complete absorption process, can be lowered below 90 °C by increasing the H2 pressure above 185 bar. Moreover, the results indicate that the hydrogenation capacity and absorption kinetics can be maintained roughly constant over several cycles. Low operating temperatures, together with fast absorption kinetics and good reversibility, make this system a promising on-board hydrogen storage material. The reasons for the improved de/re-hydrogenation properties are thoroughly investigated and discussed.

Cold sprayed WO3 and TiO2 electrodes for photoelectrochemical water and methanol oxidation in renewable energy applications.

Films prepared by cold spray have potential applications as photoanodes in electrochemical water splitting and waste water purification. In the present study cold sprayed photoelectrodes produced with WO3 (active under visible light illumination) and TiO2 (active under UV illumination) on titanium metal substrates were investigated as photoanodes for the oxidation of water and methanol, respectively. Methanol was chosen as organic model pollutant in acidic electrolytes. Main advantages of the cold sprayed photoelectrodes are the improved metal-semiconductor junctions and the superior mechanical stability. Additionally, the cold spray method can be utilized as a large-scale electrode fabrication technique for photoelectrochemical applications. Incident photon to current efficiencies reveal that cold sprayed TiO2/WO3 photoanodes exhibit the best photoelectrochemical properties with regard to the water and methanol oxidation reactions in comparison with the benchmark photocatalyst Aeroxide TiO2 P25 due to more efficient harvesting of the total solar light irradiation related to their smaller band gap energies.

Transition and Alkali Metal Complex Ternary Amides for Ammonia Synthesis and Decomposition.

A new complex ternary amide, Rb2 [Mn(NH2 )4 ], which simultaneously contains both transition and alkali metal catalytic sites, is developed. This is in line with the recently reported TM-LiH composite catalysts, which have been shown to effectively break the scaling relations and achieve ammonia synthesis under mild conditions. Rb2 [Mn(NH2 )4 ] can be facilely synthesized by mechanochemical reaction at room temperature. It exhibits two temperature-dependent polymorphs, that is, a low-temperature orthorhombic and a high-temperature monoclinic structure. Rb2 [Mn(NH2 )4 ] decomposes to N2 , H2 , NH3 , Mn3 N2 , and RbNH2 under inert atmosphere; whereas it releases NH3 at a temperature as low as 80 °C under H2 atmosphere. Those unique behaviors enable Rb2 [Mn(NH2 )4 ], and its analogue K2 [Mn(NH2 )4 ], to be excellent catalytic materials for ammonia decomposition and synthesis. Experimental results show both ammonia decomposition onset temperatures and conversion rates over Rb2 [Mn(NH2 )4 ] and K2 [Mn(NH2 )4 ] are similar to those of noble metal Ru-based catalysts. More importantly, these ternary amides exhibit superior capabilities in catalyzing NH3 synthesis, which are more than 3 orders of magnitude higher than that of Mn nitride and twice of that of Ru/MgO. The in situ SR-PXD measurement shows that manganese nitride, synergistic with Rb/KH or Rb/K(NH2 )x H1-x , are likely the active sites. The chemistry of Rb2 /K2 [Mn(NH2 )x ] and Rb/K(NH2 )x H1-x with H2 /N2 and NH3 correlates closely with the catalytic performance.

Synthesis, structures and thermal decomposition of ammine MxB12H12 complexes (M = Li, Na, Ca).

A series of ammine metal-dodecahydro-closo-dodecaboranes, MxB12H12·nNH3 (M = Li, Na, Ca) were synthesized and their structural and thermal properties studied with in situ time-resolved synchrotron radiation powder X-ray diffraction, thermal analysis, Fourier transformed infrared spectroscopy, and temperature-programmed photographic analysis. The synthesized compounds, Li2B12H12·7NH3, Na2B12H12·4NH3 and CaB12H12·6NH3, contain high amounts of NH3, 43.3, 26.6 and 35.9 wt% NH3, respectively, which can be released and absorbed reversibly at moderate conditions without decomposition, thereby making the closo-boranes favorable 'host' materials for ammonia or indirect hydrogen storage in the solid state. In this work, fifteen new ammine metal dodecahydro-closo-dodecaborane compounds are observed by powder X-ray diffraction, of which six are structurally characterized, Li2B12H12·4NH3, Li2B12H12·2NH3, Na2B12H12·4NH3, Na2B12H12·2NH3, CaB12H12·4NH3 and CaB12H12·3NH3. Li2B12H12·4NH3 and Na2B12H12·4NH3 are isostructural and monoclinic (P21/n) whereas Na2B12H12·2NH3 and CaB12H12·3NH3 are both trigonal with space groups P3[combining macron]m1 and R3[combining macron]c, respectively. Generally, coordination between the metal and the icosahedral closo-borane anion is diverse and includes point sharing, edge sharing, or face sharing, while coordination of ammonia always occurs via the lone pair on nitrogen to the metal. Furthermore, a liquid intermediate is observed during heating of Li2B12H12·7NH3. This work provides deeper insight into the structural, physical, and chemical properties related to thermal decomposition and possible ammonia and hydrogen storage.

Effects of Stoichiometry on the H2 -Storage Properties of Mg(NH2 )2 -LiH-LiBH4 Tri-Component Systems.

The hydrogen desorption pathways and storage properties of 2 Mg(NH2 )2 -3 LiH-xLiBH4 samples (x=0, 1, 2, and 4) were investigated systematically by a combination of pressure composition isotherm (PCI), differential scanning calorimetric (DSC), and volumetric release methods. Experimental results showed that the desorption peak temperatures of 2 Mg(NH2 )2 -3 LiH-xLiBH4 samples were approximately 10-15 °C lower than that of 2 Mg(NH2 )2 -3 LiH. The 2 Mg(NH2 )2 -3 LiH-4 LiBH4 composite in particular began to release hydrogen at 90 °C, thereby exhibiting superior dehydrogenation performance. All of the LiBH4 -doped samples could be fully dehydrogenated and re-hydrogenated at a temperature of 143 °C. The high hydrogen pressure region (above 50 bar) of PCI curves for the LiBH4 -doped samples rose as the amount of LiBH4 increased. LiBH4 changed the desorption pathway of the 2 Mg(NH2 )2 -3 LiH sample under a hydrogen pressure of 50 bar, thereby resulting in the formation of MgNH and molten [LiNH2 -2 LiBH4 ]. That is different from the dehydrogenation pathway of 2 Mg(NH2 )2 -3 LiH sample without LiBH4 , which formed Li2 Mg2 N3 H3 and LiNH2 , as reported previously. In addition, the results of DSC analyses showed that the doped samples exhibited two independent endothermic events, which might be related to two different desorption pathways.

The effect of Sr(OH)2 on the hydrogen storage properties of the Mg(NH2)2-2LiH system.

The doping effect of Sr(OH)2 on the Mg(NH2)2-2LiH system is investigated considering different amounts of added Sr(OH)2 in the range of 0.05 to 0.2 mol. Experimental results show that both the thermodynamic and the kinetic properties of Mg(NH2)2-2LiH are influenced by the presence of Sr(OH)2. The addition of 0.1 mol Sr(OH)2 leads to a decrease in both the dehydrogenation onset and peak temperatures of ca. 70 and 13 °C, respectively, and an acceleration in the de/re-hydrogenation rates of one time at 150 °C compared to Mg(NH2)2-2LiH alone. Based on differential scanning calorimetry (DSC) analysis, the overall reaction enthalpy of the 0.1 Sr(OH)2-doped sample is calculated to be 44 kJ per mol-H2 and there are two absorption events occurring in the doped sample instead of one in the pristine sample. For the applied experimental conditions, according to the in situ synchrotron radiation powder X-ray diffraction (SR-PXD) and Fourier Transform Infrared spectroscopy (FT-IR) analysis, the reaction mechanism has been finally defined: Sr(OH)2, Mg(NH2)2 and LiH react with each other to form SrO, MgO and LiNH2 during ball milling. After heating, SrO interacts with Mg(NH2)2 producing MgO and Sr(NH2)2. Then Mg(NH2)2, LiNH2 and Sr(NH2)2 react with LiH to produce Li2NH, SrNH, Li2Mg(NH)2 and Li2Mg2(NH)3 in traces. After re-hydrogenation, LiSrH3, LiH and LiNH2 are formed along with amorphous Mg(NH2)2. The reasons for the improved kinetics are: (a) during dehydrogenation, the in situ formation of SrNH appears to increase the interfacial contacts between Mg(NH2)2 and LiH and also weakens the N-H bond of Mg(NH2)2; (b) during absorption, the formation of LiSrH3 at around 150 °C could be the key factor for improving the hydrogenation properties.

Reforms of Retirement Policies: Three Common Paths in Aging in Japan and Korea.

Faced with an unparalleled rate of population aging, Japan and Korea have been reforming their retirement policies. To date, however, while the age of mandatory retirement has increased, employees continue to face significant decreases in compensation and other working conditions, typically at age 60 in Japan and age 55 in Korea. Three factors have contributed to shaping the path of the policy reforms in both the countries, including (1) the productivist welfare regimes, (2) the structure of the labor market for young workers, and (3) seniority-based wage and compensation systems.

KNH2-KH: a metal amide-hydride solid solution.

We report for the first time the formation of a metal amide-hydride solid solution. The dissolution of KH into KNH2 leads to an anionic substitution, which decreases the interaction among NH2- ions. The rotational properties of the high temperature polymorphs of KNH2 are thereby retained down to room temperature.

New synthesis route for ternary transition metal amides as well as ultrafast amide-hydride hydrogen storage materials.

K2[Mn(NH2)4] and K2[Zn(NH2)4] were successfully synthesized via a mechanochemical method. The mixture of K2[Mn(NH2)4] and LiH showed excellent rehydrogenation properties. In fact, after dehydrogenation K2[Mn(NH2)4]-8LiH fully rehydrogenates within 60 seconds at ca. 230 °C and 5 MPa of H2. This is one of the fastest rehydrogenation rates in amide-hydride systems known to date. This work also shows a strategy for the synthesis of transition metal nitrides by decomposition of the mixtures of M[M'(NH2)n] (where M is an alkali or alkaline earth metal and M' is a transition metal) and metal hydrides.

Ternary Amides Containing Transition Metals for Hydrogen Storage: A Case Study with Alkali Metal Amidozincates.

The alkali metal amidozincates Li4 [Zn(NH2)4](NH2)2 and K2[Zn(NH2)4] were, to the best of our knowledge, studied for the first time as hydrogen storage media. Compared with the LiNH2-2 LiH system, both Li4 [Zn(NH2)4](NH2)2-12 LiH and K2[Zn(NH2)4]-8 LiH systems showed improved rehydrogenation performance, especially K2[Zn(NH2)4]-8 LiH, which can be fully hydrogenated within 30 s at approximately 230 °C. The absorption properties are stable upon cycling. This work shows that ternary amides containing transition metals have great potential as hydrogen storage materials.