Tethering Three Radical Cascades for Controlled Termination of Radical Alkyne peri-Annulations: Making Phenalenyl Ketones without Oxidants.

Although Bu3Sn-mediated radical alkyne peri-annulations allow access to phenalenyl ring systems, the oxidative termination of these cascades provides only a limited selection of the possible isomeric phenalenone products with product selectivity controlled by the intrinsic properties of the new cyclic systems. In this work, we report an oxidant-free termination strategy that can overcome this limitation and enable selective access to the full set of isomerically functionalized phenalenones. The key to preferential termination is the preinstallation of a "weak link" that undergoes C-O fragmentation in the final cascade step. Breaking a C-O bond is assisted by entropy, gain of conjugation in the product, and release of stabilized radical fragments. This strategy is expanded to radical exo-dig cyclization cascades of oligoalkynes, which provide access to isomeric π-extended phenalenones. Conveniently, these cascades introduce functionalities (i.e., Bu3Sn and iodide moieties) amenable to further cross-coupling reactions. Consequently, a variety of polyaromatic diones, which could serve as phenalenyl-based open-shell precursors, can be synthesized.

Influence of Al2O3 Overlayers on Intermolecular Interactions between Metal Oxide Bound Molecules.

Intermolecular interactions on inorganic substrates can have a critical impact on the electrochemical and photophysical properties of the materials and subsequent performance in hybrid electronics. Critical to the intentional formation or inhibition of these processes is controlling interactions between molecules on a surface. In this report, we investigated the impact of surface loading and atomic-layer-deposited Al2O3 overlayers on the intermolecular interactions of a ZrO2-bound anthracene derivative as probed by the photophysical properties of the interface. While surface loading density had no impact on the absorption spectra of the films, there was an increase in excimer features with surface loading as observed by both emission and transient absorption. The addition of ALD overlayers of Al2O3 resulted in a decrease in excimer formation, but the emission and transient absorption spectra were still dominated by excimer features. These results suggest that ALD may provide a post-surface loading means of influencing such intermolecular interactions.

A fluorescent turn-on sensor for mercury (II) ions in near neutral poly(metharylic acid) solution.

The conformational change of poly (methacrylic acid) (PMAA) at various pH values is well studied; however, the application of PMAA in the field of analytical chemistry has been very limited. This investigation takes advantage of the conformational change of PMAA at various pH levels and the conformational change induced by metal ions. By adjusting the pH, thiophene-phenylanilide-acridinium molecules can serve as turn-on sensors for Hg2+ ions. In pH 7.4 buffer with PMAA molecules, the sensor is selectively turned on by Hg2+ ions to display strong charge shift state (CSH) emission at 560 nm. The intensity shows linear response to the concentration of Hg2+ ions between 0.020 mM and 0.151 mM with a detection limit in nanomolar range. The photophysical properties of sensor molecules in PMAA/mercury (II) mixture at near neutral pH are comparable to those in PMAA solution in acidic condition without mercury (II) ions. The effect of pH, temperature, polymer size, and polymer concentration on emission intensity were investigated. The sensor showed excellent percent recovery (98.4 % to 103 %) of spiked mercury (II) ions in real water samples. The sensing mechanism is likely through intrachain and interchain coordination of mercury (II) ions with the carboxyl groups on the side chain of PMAA to induce an extended coil conformation of PMAA. Calculations support the conclusion that the size and geometry of the binding sites formed inside PMAA are suitable to incorporate sensor molecules and enhance the charge shift state emission of sensor molecules.

Examining the influence of bilayer structure on energy transfer and molecular photon upconversion in metal ion linked multilayers.

Metal ion linked multilayers is a unique motif to spatially control and geometrically restrict molecules on a metal oxide surface and is of interest in a number of promising applications. Here we use a bilayer composed of a metal oxide surface, an anthracene annihilator molecule, Zn(II) linking ion, and porphyrin sensitizers to probe the influence of the position of the metal ion binding site on energy transfer, photon upconversion, and photocurrent generation. Despite being energetically similar, varying the position of the carboxy metal ion binding group (i.e. ortho, meta, para) of the Pt(II) tetraphenyl porphyrin sensitizer had a large impact on energy transfer rates and upconverted photocurrent that can be attributed to differences in their geometries. From polarized attenuated total reflectance measurements of the bilayers on ITO, we found that the orientation of the first layer (anthracene) was largely unperturbed by subsequent layers. However, the tilt angle of the porphyrin plane varies dramatically from 41° to 64° to 57° for the para-, meta-, and ortho-COOH substituted porphyrin molecules, which is likely responsible for the variation in energy transfer rates. We go on to show using molecular dynamics simulations that there is considerable flexibility in porphyrin orientation, indicating that an average structure is insufficient to predict the ensemble behavior. Instead, even a small subset of the population with highly favorable energy transfer rates can be the primary driver in increasing the likelihood of energy transfer. Gaining control of the orientation and its distribution will be a critical step in maximizing the potential of the metal ion linked structures.