Pharmaceutical and personal care products (PPCPs) degradation and microbial characteristics of low-temperature operation combined with constructed wetlands.

Emerging contaminants (ECs), which are present in water bodies, could cause global environmental and human health problems. These contaminants originate from various sources such as hospitals, clinics, households, and industries. Additionally, they can also indirectly enter the water supply through runoff from agriculture and leachate from landfills. ECs, specifically Pharmaceutical and personal care products (PPCPs), are causing widespread concern due to their contribution to persistent water pollution. Traditional approaches often involve expensive chemicals and energy or result in the creation of by-products. This study developed a practical and environmentally-friendly method for removing PPCPs, which involved combining and integrating various techniques. To implement this method, it was necessary to establish and used a field simulator based on the real-life scenario. Based on the data analysis, the average removal rates of COD, TP, TN, and NH4+-N were 57%, 59%, 63%, and 73%, respectively. the removal rate of PPCPs by CCWs was found to be 82.7% after comparing samples that were not treated by constructed wetlands and those that were treated. Combined constructed wetlands (CCWs) were found to effectively remove PPCPs from water. This is due to the combined action of plant absorption, absorption, and biodegradation by microorganisms living in the wetlands. Interestingly, the wetland plant reed had been shown to play an important role in removing these pollutants. Microbial degradation was the most important pathway for PPCPs removal in CCWs. Carbamazepine was selected as a typical PPCP for analysis. In addition, the microbial community structure of the composite filler was also investigated. High-throughput sequencing confirmed that the dominant bacteria had good adaptability to PPCPs. This technique not only reduced the potential environmental impact but also served as a foundation for further research on the use of constructed wetlands for the treatment of PPCPs contaminated water bodies and its large-scale implementation.

Impact of separate concentrations of polyethylene microplastics on the ability of pollutants removal during the operation of constructed wetland-microbial fuel cell.

Microplastics (MPs) in water pose a great threat to the ecological environment, but the impact of MPs on constructed wetland microbial fuel cells (CW-MFCs) has not been studied, so in order to fill the research gap and enrich the research in the field of microplastics, a 360-day experiment was designed to determine the operating status of CW-MFCs at different concentrations (0, 10, 100 and 1000 µg/L) polyethylene microplastics (PE-MPs) at different times, focusing on the changes of the CW-MFCs' ability to handle pollutants, power production performance and microbial composition. The results showed that with the accumulation of PE-MPs, the removal effect of COD and TP did not change significantly, and that the removal rate was maintained at around 90% and 77.9% respectively, within 120 d of operation. What's more, the denitrification efficiency increased (from 4.1% to 19.6%), but with the passage of time, it decreased significantly (from 7.16% to 31.9%) at the end of the experiment, while oxygen mass transfer rate was significantly increased. Further analysis showed that the accumulation of PE-MPs did not affect the current power density significantly with the changes of time and concentration, but the accumulation of PE-MPs would inhibit the exogenous electrical biofilm and increase the internal resistance, thereby affecting the electrochemical performance of the system. In addition, the results of microbial PCA showed that the composition and the activity of the microorganisms were changed under the action of PE-MPs, that the microbial community in CW-MFC showed a dose effect on the input of PE-MPs, and that the relative abundance of nitrifying bacteria with time was significantly affected by PE-MPs concentration. The relative abundance of denitrifying bacteria decreased over time, but PE-MPs promoted the reproduction of denitrifying bacteria, which was consistent with the changes in nitrification and denitrification rates. The removal modes of EP-MPs by CW-MFC include the adsorption and the electrochemical degradation, with two isothermal adsorption models of Langmuir and Freundlich being constructed in the experiment, and the electrochemical degradation process of EP-MPs being simulated. In summary, the results show that the accumulation of PE-MPs can induce a series of changes in substrate, microbial species and activity of CW-MFCs, which in turn affects the pollutant removal efficiency and power generation performance during its operation.

Decomposition of Phosphorus Pollution and Microorganism Analysis Using Novel CW-MFCs under Different Influence Factors.

A constructed wetland (CW)-coupled microbial fuel cell (MFC) system was constructed to treat wastewater and generate electricity. The total phosphorus in the simulated domestic sewage was used as the treatment target, and the optimal phosphorus removal effect and electricity generation were determined by comparing the changes in substrates, hydraulic retention times, and microorganisms. The mechanism underlying phosphorus removal was also analyzed. By using magnesia and garnet as substrates, the best removal efficiencies of two CW-MFC systems reached 80.3% and 92.4%. Phosphorus removal by the garnet matrix mainly depends on a complex adsorption process, whereas the magnesia system relies on ion exchange reactions. The maximum output voltage and stabilization voltage of the garnet system were higher than those of the magnesia system. Microorganisms in the wetland sediments and electrode also changed considerably. It indicates that the mechanism of phosphorus removal by the substrate in the CW-MFC system is adsorption and chemical reaction between ions to generate precipitation. The population structure of proteobacteria and other microorganisms has an impact on both power generation and phosphorus removal. Combining the advantages of constructed wetlands and microbial fuel cells also improved phosphorus removal in coupled system. Therefore, when studying a CW-MFC system, the selection of electrode materials, matrix, and system structure should be taken into account to find a method that will improve the power generation capacity of the system and remove phosphorus.