RESUMEN
Ion-selective electrodes (ISEs) have widespread use in the fields of clinical and environmental analyses. Tetrahydrofuran (THF) is the most used solvent for the preparation of modern ISEs, equipped with ion-selective membranes (ISMs). Until now, the influence of impurities in THF toward potentiometric instability of ion-selective membrane based ISEs was probably associated with the presence of either residual water or peroxide. To address this issue, most literature recommends redistilling THF prior to use in the preparation of the potentiometric membranes. Current study reveals that the actual THF impurity that is responsible for potential instability in the ISM includes products from the oxidation of THF, which contains the hydroxyl group and possibly carbonyl group with a boiling point of above 200 °C. The density functional theory calculation supported pathway of the chemical reaction of THF oxidation, hence, the chemical structure of the uncertain impurities was predicted. The underlying reason for the deteriorating potential stability of the ISEs is proposed as the significant hydrophilicity of these impurities that affect the partitioning of the ion sensing components in the membrane, thus enhancing the leaching of the membrane components from the membrane phase. This finding explains why redistillation of aged THF is advised.
Asunto(s)
Furanos , Furanos/química , Electrodos de Iones Selectos , Oxidación-Reducción , Membranas Artificiales , Potenciometría , Teoría Funcional de la DensidadRESUMEN
In this study, a gravity-driven membrane (GDM) filtration system and hydroponic system (cultivating basil and lettuce) were combined for nutrient recovery from primary municipal wastewater. The GDM system was optimized by increasing the periodic air sparging flow rate from 1 to 2 L/min (â¼15 hr per 3-4 days), resulting in a â¼52% reduction of irreversible fouling. However, the total fouling was not alleviated, and the water productivity remained comparable. The GDM-filtrated water was then delivered to hydroponic systems, and the effects of hydroponic operation conditions on plant growth and heavy metal uptake were evaluated, with fertilizer- and tap water-based hydroponic systems and soil cultivation system (with tap water) for comparison. It was found that (i) the hydroponic system under batch mode facilitated to promote vegetable growth with higher nutrient uptake rates compared to that under flow-through feed mode; (ii) a shift in nutrient levels in the hydroponic system could impact plant growth (such as plant height and leaf length), especially in the early stages. Nevertheless, the plants cultivated with the GDM-treated water had comparable growth profiles to those with commercial fertilizer or in soils. Furthermore, the targeted hazard quotient levels of all heavy metals for the plants in the hydroponic system with the treated water were greatly lower than those with the commercial fertilizer. Especially, compared to the lettuce, the basil had a lower heavy metal uptake capability and displayed a negligible impact on long-term human health risk, when the treated water was employed for the hydroponic system.
Asunto(s)
Filtración , Hidroponía , Nutrientes , Eliminación de Residuos Líquidos , Aguas Residuales , Eliminación de Residuos Líquidos/métodos , Nutrientes/análisis , Nutrientes/metabolismo , Cerámica , Membranas Artificiales , Contaminantes Químicos del Agua/análisis , Gravitación , FertilizantesRESUMEN
Paper-based microfluidics combined with potentiometric measurement has emerged as an attractive approach for detecting various chemical ionic moieties. Detection of heavy metal ions, using paper substrates as solution sampling and delivery systems remains challenging despite efforts to introduce several physico-chemical paper substrate modifications to stop adsorption of ions onto the paper substrates. This study quantitatively investigates the adsorption of heavy metal ions on the paper substrates during paper-based potentiometric measurements and explains the super-Nernstian response of potentiometric sensors through local depletion of heavy metal ions from the solution. Consequently, based on the investigated ion adsorption, a corrective potential protocol was established for the electrodes coupled with paper-based solution sampling by predicting interference free sensor response from paper-based measurement. Furthermore, the ion adsorption was also recorded for mixed metal ion solutions to understand competitive primary/interfering ions adsorption onto the paper substrates and establish corrective measures to predict interference free sensor response. In this method, no modifications of the paper substrates are necessary before actual potentiometric measurements. The proposed corrective protocol allows prediction of sensor response based on the paper-based solution sampling potentiometric measurement, providing a simple methodological approach based on correction of potential readout of the potentiometric sensor, thus completely resigning from the need of modifying paper substrate for measurements of heavy metal ions.
RESUMEN
Prolonged drought conditions are a critical challenge for agricultural advancement, threatening food security and environmental equilibrium. To overcome these issues, enhancing plant resilience to drought is essential for plant growth and sustainable agriculture. In this study, blue-emitting antioxidant carbon dots (B-CDs), synthesized from citric acid and ascorbic acid, emerged as a promising solution to enhance the drought resistance of peas (Pisum sativum L.). B-CDs can efficiently scavenge reactive oxygen species (ROS), which are harmful in excess to plants under stress conditions. Through detailed experimental analyses and density functional theory (DFT) studies, it is found that these B-CDs possess structures featuring eight-membered aromatic rings with abundant oxygen-containing functional groups, providing active sites for reactions with ROS. The practical benefits of the B-CDs are evident in tests with pea plants exposed to drought conditions. These plants show a remarkable reduction in ROS accumulation, an increase in photosynthetic efficiency due to improved electron transfer rates, and significant growth enhancement. Compared to untreated controls under drought stress, the application of B-CDs results in an impressive increase in the fresh and dry weights of both the shoots and roots of pea seedlings by 39.5 and 43.2% for fresh weights and 121.0 and 73.7% for dry weights, respectively. This suggests that B-CDs can significantly mitigate the negative effects of drought on plants. Thus, leveraging B-CDs opens a novel avenue for enhancing plant resilience to abiotic stressors through nanotechnology, thereby offering a sustainable pathway to counter the challenges of drought in agriculture.
Asunto(s)
Antioxidantes , Carbono , Resistencia a la Sequía , Pisum sativum , Puntos Cuánticos , Especies Reactivas de Oxígeno , Antioxidantes/química , Antioxidantes/metabolismo , Ácido Ascórbico/química , Carbono/química , Ácido Cítrico/química , Fotosíntesis/efectos de los fármacos , Pisum sativum/efectos de los fármacos , Pisum sativum/metabolismo , Puntos Cuánticos/química , Especies Reactivas de Oxígeno/metabolismoRESUMEN
The removal of uranyl ions (UO2 2+) from water is challenging due to their chemical stability, low concentrations, complex water matrix, and technical limitations in extraction and separation. Herein, a novel molybdenum disulfide/graphene oxide heterojunction (MoS2/GO-H) is developed, serving as an effective electrode for capacitive deionization (CDI). By combining the inherent advantages of electroadsorption and electrocatalysis, an innovative electroadsorption-electrocatalysis system (EES) strategy is introduced. This system utilizes interface polarization at the MoS2 and GO interface, creating an additional electric field that significantly influences carrier behavior. The MoS2/GO-H electrode, with its extraordinary adsorption capacity of 805.57 mg g-1 under optimal conditions, effectively treated uranium-laden wastewater from a mine, achieving over 90% removal efficiency despite the presence of numerous competing ions at concentrations significantly higher than UO2 2+. Employing density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations, it is found that the MoS2/GO-H total charge density at the Fermi level, enhanced by interfacial polarization, surpasses that of separate MoS2 and GO, markedly boosting conductivity and electrocatalytic effectiveness.
RESUMEN
Leaching of potentially hazardous substances, especially the heavy metals from Incineration Bottom Ash (IBA) is a major problem in its recyclable usage. To address this concern, treatment of IBA is indispensable before it can be reused. IBA subjected to laboratory-scale treatment typically yields clearer conclusions in terms of leaching behaviors, benefiting from the controlled laboratory environment. However, the leaching behaviors of commercially treated IBA appear to be more ambiguous due to the complex and comprehensive nature of industrial-scale treatments, where multiple treatment techniques are involved concurrently. Furthermore, treatment efficiencies vary among different plants. In this study, three types of commercially treated IBA were sampled from leading waste treatment companies in Singapore. Characterization and leaching tests were performed on the treated IBAs in both standardized and modified manners to simulate various scenarios. Besides deionized water, artificial seawater was used as a leachant in leaching tests for simulating seawater intrusion. The results reveal the promoting effect of seawater on the leaching levels of several elements from three types of treated IBA, which may require special attention for IBA application and landfill near the coast. Furthermore, the elements examined in these three types of commercially treated IBA generally comply with the non-hazardous waste acceptance criteria outlined in Council Decision, 2003/33/EC (2003), except Sb. By combining two leaching tests, the elements were categorized into different types of leaching behavior, making it possible to prepare and respond to the concerning leaching scenarios in future engineering applications.
Asunto(s)
Ceniza del Carbón , Metales Pesados , Singapur , Incineración , Metales Pesados/análisis , Conservación de los Recursos Naturales , Residuos Sólidos/análisisRESUMEN
Globally waste incineration is becoming the predominant treatment method of solid waste. The largest fraction of solid residue of this process is incineration bottom ash (IBA) requiring further treatment before applications such as in the construction industry become feasible. In this study, vitrification of IBA was conducted in a demonstration-scale high-temperature slagging gasification plant fueled with MSW and biomass charcoal as a green auxiliary fuel. High IBA co-feeding rates of up to 491 kg/h (equivalent to 107% of MSW feeding rate) were achieved during the trials. A highly leaching-resistant slag immobilizing heavy metals in the glass-like amorphous structure and recyclable iron-rich metal granules were generated in the process. The heavy metal migration into the solid by-product fractions depended on the IBA feeding rates and process conditions such as cold cap temperature, charcoal-to-ash ratio, and gasifier temperature profile. Slaked lime and activated carbon powder were used in a dry flue gas treatment and stack gas emissions were kept well below Singapore's regulatory limits. Steam from the hot flue gas was generated in a boiler to drive a steam turbine. The application of biomass charcoal instead of fossil fuels or electricity lead to a lower carbon footprint compared to alternative vitrification technologies. The overall results reveal promising application of high temperature slagging gasification process for commercial-scale vitrification of IBA.
Asunto(s)
Metales Pesados , Eliminación de Residuos , Ceniza del Carbón/química , Vapor , Huella de Carbono , Carbón Orgánico , Vitrificación , Incineración/métodos , Metales Pesados/química , Residuos SólidosRESUMEN
Acoustic agglomeration is a technique that leverages on sound waves to promote the collision of aerosol particulate matter, thus leading to the formation of larger particle agglomerates. In this study, this acoustics-driven phenomenon is demonstrated for its usefulness as an aerosol pre-conditioning method to significantly enhance the efficiency of filtration systems in particle treatment processes. Specifically, favorable changes in pressure drop across the filters are observed as a result of receiving less particle mass, for which filters are shown to be able to have their operational life extended remarkably by more than 50%. The involved ultrasonic aerosol agglomeration mechanisms are unveiled through numerical simulations, and the effects of residence time, sound pressure level, and initial particle number concentration on agglomeration performances are experimentally investigated. In addition, validations and measurements of filter pressure drop are obtained through a series of experiments. This study provides a comprehensive overview to the design and performance characterization of acoustics-agglomeration-enhanced filtration systems, which could potentially derive energy savings for fan power in ventilation systems and be scaled up for applications in industrial plants for reducing carbon emissions.
RESUMEN
With the proliferation of reverse osmosis technology, seawater reverse osmosis desalination has been heralded as the solution to water scarcity for coastal regions. However, the large volume of desalination brine produced may pose an adverse environmental impact when directly discharged into the sea and result in energy wastage as the seawater pumped out is dumped back into the sea. Recently, zero liquid discharge has been extensively studied as a way to eliminate the aquatic ecotoxicity impact completely, despite being expensive and having a high carbon footprint. In this work, we propose a new strategy towards the treatment of brine to seawater level for disposal, dubbed reclaimed seawater discharge (RSD). This process is coupled with existing resource recovery techniques and waste alkali CO2 capture processes to produce an economically viable waste treatment process with minimal CO2 emissions. In this work, we placed significant focus on the electrolysis of brine, which simultaneously lowers the salinity of the desalination brine (56.0 ± 2.1 g/L) to seawater level (32.0 ± 1.4 g/L), generates alkali brine from seawater (pH 13.6) to remove impurities in brine (Mg2+ and Ca2+ to below ppm level), and recovers magnesium hydroxide, calcium carbonate, chlorine, bromine, and hydrogen gas as valuable resources. The RSD is further chemically dechlorinated and neutralised to pH 7.3 to be safe to discharge into the sea. The excess alkali brine is used to capture additional CO2 in the form of bicarbonates, achieving net abatement in climate change impact (9.90 CO2 e/m3) after product carbon abatements are accounted.
Asunto(s)
Sales (Química) , Purificación del Agua , Purificación del Agua/métodos , Dióxido de Carbono , Ósmosis , Agua de Mar , Salinidad , ÁlcalisRESUMEN
Switching from a linear mode of waste management to a circular loop by transforming plastic waste into carbon nanotubes (CNTs) is a promising approach to current plastic waste treatment. One of the many applications of CNTs is its use for electrocatalytic water splitting for hydrogen evolution. Existing methods of CNTs-based hydrogen evolution reaction (HER) electrode fabrication involve additives like polymeric binders and additional steps to improve CNT dispersion, which are detrimental to the CNT structure and properties. The in-situ fabrication approach can potentially be a one-pot solution to HER electrode synthesis. In this study, polyolefins pyrolysis gas and a Co:Ni:Mg catalyst were used to fabricate binder-free CNTs-based electrodes on different substrates for HER. The study assessed CNT quality on conductive carbon paper, semiconductive silicon, and dielectric glass substrates, evaluating their HER performance in 1 M KOH. A mixture of hollow-core, bamboo-like, and cup-stacked arrangement nanotubes were synthesized on the substrates, with CNTs on glass and carbon paper substrates possessing better graphitization than CNTs grown on silicon. This is in agreement with HER performance, whereby the as-prepared electrodes required overpotentials of 267 mV, 241 mV, and 216 mV for silicon, glass, and carbon paper, respectively, to achieve 10 mA/cm2. Despite being poorly conductive, the glass substrate electrode achieved a lower overpotential than the silicon electrode. Additionally, the as-prepared silicon electrode faced a delamination issue likely attributed to the lower surface energy of the silicon substrate surface, demonstrating the weaker adhesion between the CNTs and silicon surface. The proposed approach thus showed that the in-situ fabricated electrodes performed better than separately synthesized CNTs prepared into electrodes by 27.4% and 14.2% for carbon paper and glass substrates, respectively. The improved performance of the as-prepared, binder-free electrodes can be linked to the lower charge-transfer resistance and reduced contact resistance between the CNTs and substrate.
Asunto(s)
Nanotubos de Carbono , Nanotubos de Carbono/química , Silicio , Hidrógeno , ElectrodosRESUMEN
Numerous efforts have been devoted to understanding the electron transfer process of uranium (UO22+) on adsorbent materials, whereas the potential oxygen vacancies (OVs) in metal oxides have long been overlooked. Once these interactions are taken into account, the emerging molecular orbital effects undoubtedly affect the adsorption process. Here, we synthesized CC/γ-MnO2 by growing MnO2 on carbon cloth (CC), followed by the creation of oxygen vacancies (OVs) through electrochemical methods to form CC/γ-MnO2-OVs. The CC/γ-MnO2-OVs shows significantly enhanced selectivity and durability for UO22+, with the maximum adsorption capacity increasing from 456.8 to 1648.1 mg/g (by a factor of 3.6). Theoretical calculations suggest that the generation of OVs leads to an increase in charge transfer and a decrease in adsorption energy between UO22+ and CC/γ-MnO2, due to the interaction between Mn 3d orbital in CC/γ-MnO2 and O 2p orbital in UO22+. The OVs in CC/γ-MnO2 provide a spatial structure for anchoring the OU=O moiety of UO22+, while the surface van der Waals forces and the formation of chemical bonds between Mn-U contribute to charge interactions. This synergistic effect allows CC/γ-MnO2-OVs to exhibit favorable selectivity, a large adsorption capacity, and rapid adsorption kinetics towards uranyl ions. This work achieves enhanced UO22+ separation by introducing OVs in CC/γ-MnO2 through a facile electrochemical strategy, highlighting the great potential for nuclear waste processing.
RESUMEN
Utilization of renewable raw materials as feedstock defossilizes industrial manufacturing while subsequent carbon capture reduces carbon footprint. We applied this concept to design a new pyrolysis-based process for synthesis of biogenic multi-walled carbon nanotubes (MWCNTs) and H2 from biomass. It was demonstrated that the conversion of hydrocarbon compounds in pyrolysis gas into MWCNTs and H2 is detrimentally influenced by accompanied CO2 released from biomass decomposition. Capturing CO2 with a calcium sorbent upgraded the pyrolysis gas into a suitable gaseous precursor for downstream production of MWCNTs and H2 -rich gas. Furthermore, the results suggest that CO2 capture with the sorbent has a potential to outperform a liquid alkaline scrubber owing to avoided liquid organic waste generation, sorbent regenerability and higher H2 recovery from biomass pyrolysis gas.
Asunto(s)
Dióxido de Carbono , Nanotubos de Carbono , Biomasa , Hidrógeno , PirólisisRESUMEN
A multiphase CFD-DEM model was built to simulate the waste-to-energy gasifying and direct melting furnace in a pilot demonstration facility. The characterizations of feedstocks, waste pyrolysis kinetics, and charcoal combustion kinetics were first obtained in the laboratory and used as model inputs. The density and heat capacity of waste and charcoal particles were then modelled dynamically under different status, composition, and temperature. A simplified ash melting model was developed to track the final fate of waste particles. The simulation results were in good agreement with the site observations in both temperature and slag/fly-ash generations, verifying the CFD-DEM model settings and gas-particle dynamics. More importantly, the 3-D simulations quantified and visualized the individual functioning zones in the direct-melting gasifier as well as the dynamic changes throughout the whole lifetime of waste particles, which is otherwise technically unachievable for direct plant observations. Hence, the study demonstrates that the established CFD-DEM model together with the developed simulation procedures can be used as a tool for the optimisation of operating conditions and scaled-up design for future prototype waste-to-energy gasifying and direct melting furnace.
Asunto(s)
Carbón Orgánico , Residuos Sólidos , Residuos Sólidos/análisis , Ceniza del Carbón , Temperatura , Calor , Incineración/métodosRESUMEN
The replacement of natural gas with plastic-derived pyrolysis gas can defossilize H2 production, while subsequent capture, utilization and storage of carbon in a solid form can decarbonize the process. The objective of this study was to investigate H2 production from three types of plastics using a process comprising pyrolysis (600 °C) and thermolysis stages (1200-1500 °C). Depending on the plastic feedstock and thermolysis temperature, the laboratory-scale setup generated 1000-1350 mL/min product gas with H2 purity of 74.3-94.2 vol%. The recovery of 5-9 wt% molecular H2 per mass of plastics was achieved. Other products included solid residue (0.1-12 wt%) and oil (8-52 wt%) from the pyrolysis reactor, solid carbon (36-53 wt%) and gas impurities (2-16 wt%) from the thermolysis reactor. The purity of H2 gas was detrimentally influenced by polyethylene terephthalate in the feedstock due to the dilution of gas by CO. The decomposition of methane containing in the pyrolysis gas was the limiting reaction step during H2 production and improved at higher thermolysis temperature. Three solid carbon structures were formed during the thermolysis stage regardless of the plastic type: carbon black aggregates, carbon black aggregates coated with a layer of pyrolytic carbon and a carbon film on the inner reactor wall. Among the three types of carbon, the highest valorization potential was identified for carbon black aggregates. Plastic feedstock composition had little if any effect on carbon black properties, while high thermolysis temperature (1500 °C) reduced the particle sizes and increased the surface area of aggregates.
RESUMEN
Polymer foam that provides good support with high energy return (low energy loss) is desirable for sport footwear to improve running performance. Ethylene-vinyl acetate copolymer (EVA) foam is commonly used in the midsole of running shoes. However, EVA foam exhibits low mechanical properties. Conventional mineral fillers are usually employed to improve EVA's mechanical performance, but the energy return is sacrificed. Here, we produced nanocomposite foams from EVA and multi-walled carbon nanotubes (CNT) using a chemical foaming process. Two kinds of CNT derived from the upcycling of commodity plastics were prepared through a catalytic chemical vapor deposition process and used as reinforcing and nucleating agents. Our results show that EVA foam incorporated with oxygenated CNT (O-CNT) demonstrated a more pronounced improvement of physical, mechanical, and dynamic impact response properties than acid-purified CNT (A-CNT). When CNT with weight percentage as low as 0.5 wt% was added to the nanocomposites, the physical properties, abrasion resistance, compressive strength, dynamic stiffness, and rebound performance of the EVA foams were improved significantly. Unlike the conventional EVA formulation filled with talc mineral fillers, the incorporation of CNT does not compromise the energy return of the EVA foam. From the long-cycle dynamic fatigue test, the CNT/EVA foam displays greater properties retention as compared to the talc/EVA foam. This work demonstrates a good balanced of mechanical-energy return properties of EVA nanocomposite foam with very low CNT content, which presents promising opportunities for lightweight-high rebound midsoles for running shoes.
RESUMEN
Seed nano-priming is a promising technology employed in the agronomic field to promote seed germination and plant growth. However, the effects of carbon dots (CDs) on plant development via seed nano-priming remain unclear. In the present study, CDs synthesized from non-biodegradable plastic wastes were adopted as a nano-priming agent for pea (Pisum sativum) seed treatment. The results demonstrated positive effects of seed priming at all CD concentrations (0.25-2 mg/mL), including accelerated seed germination rate, increased shoot and root elongation, biomass accumulation, and root moisture level compared to the control groups. Surface erosion of seed coat was observed after CD priming, which effectively promoted seed imbibition capability. CD penetration, internalization, and translocation were confirmed using transmission electron microscopy. Furthermore, the CD-plant interaction significantly enhanced seed antioxidant enzyme activity, as well as augmented root vigor, chlorophyll content, and carbohydrate content. These findings exhibit great potential of waste-derived CDs as nano-priming agents for seed germination and seedling development in a cost-effective and sustainable manner.
Asunto(s)
Germinación , Plantones , Pisum sativum , Carbono/farmacología , Antioxidantes/farmacología , SemillasRESUMEN
Herein, five N, S-co-doped carbocatalysts were prepared from different carbonaceous precursors, namely sawdust (SD), biochar (BC), carbon-nanotubes (CNTs), graphite (GP), and graphene oxide (GO) and compared. Generally, as the graphitization degree increased, the extent of N and S doping decreased, graphitic N configuration is preferred, and S configuration is unaltered. As peroxymonosulfate (PMS) activator for ciprofloxacin (CIP) removal, the catalytic performance was in order: NS-CNTs (0.037 min-1) > NS-BC (0.032 min-1) > NS-rGO (0.024 min-1) > NS-SD (0.010 min-1) > NS-GP (0.006 min-1), with the carbonaceous properties, rather than the heteroatoms content and textural properties, being the major factor affecting the catalytic performance. NS-CNTs was found to have the supreme catalytic activity due to its remarkable conductivity (3.38 S m-1) and defective sites (ID/IG = 1.28) with high anti-interference effect against organic and inorganic matter and varying water matrixes. The PMS activation pathway was dominated by singlet oxygen (1O2) generation and electron transfer regime between CIP and PMS activated complexes. The CIP degradation intermediates were identified, and a degradation pathway is proposed. Overall, this study provides a better understanding of the importance of selecting a suitable carbonaceous platform for heteroatoms doping to produce superior PMS activator for antibiotics decontamination.
Asunto(s)
Carbono , Nanotubos de Carbono , Nitrógeno/química , Ciprofloxacina , Peróxidos/químicaRESUMEN
Removal of radioactive uranyl ions (UO22+) from water by effective adsorbents is highly desired but remains a challenge. UO22+ are easily combined with H2O, and the polarization of H2O affects the complexation between UO22+ and the adsorbent. Thus, it is necessary to reconstruct the UO22+ active site to improve the adsorption capacity. Herein ï¼an amphiphilic ligand, namely N, N-dimethyl-9-decenamide (NND), is successfully prepared. NND replace H2O in [UO2(H2O)5]2+ by hydrogen bonding, thereby enhancing the adsorption capacity of MoS2 particles in the reconstituted UO22+ active sites. The predicted maximum adsorption capacity increased from 50.7 to 500.7 mg g- 1 (by a factor of 9.87) with the presence of NND, which is higher than other functional group-modified MoS2 adsorbents. Furthermore, NND and MoS2 can retain UO22+ uptake under extreme conditions including high acid-base and gamma irradiation. Theoretical Calculations of NND through H bonding produces an increased amount of charge transfer and a reduced adsorption energy between UO22+ and MoS2, which weakens the polarization effect of H2O. The findings showed that NND appeared to be a promising amphiphilic to improve the adsorption efficiency of UO22+ from water.
RESUMEN
Paper-based microfluidic solution sampling is a viable option for potentiometric sensors to be used for the determination of analytes in samples with high solid-to-liquid ratios. Unfortunately, heavy metal sensitive electrodes cannot be easily integrated with paper-based solution sampling as heavy metals have strong physicochemical adsorption affinity towards paper substrates. In this work, paper substrates were modified with an ion-selective membrane (ISM) cocktail (used for the preparation of Pb2+-ion-selective electrodes (ISEs)) and coupled with model heavy metal Pb2+-ISEs. It was found that the super-Nernstian response of Pb2+-ISEs was eliminated when 10 to 50 mg ml-1 of the ISM cocktail was used for the modification of paper substrates. The modification of the paper substrates by Pb2+-ISM allowed the elimination of adsorption sites. In addition, it resulted in an improvement of sensor performance in terms of their detection limits to be similar to those for conditioned electrodes in standard beaker-based measurements. It is believed that the elimination of super-Nernstian response of the electrodes and improving the potentiometric responses and detection limits of ISEs were attributed to the compatibility improvement of the paper substrates and Pb2+-ISEs to the same type of ISM.
Asunto(s)
Metales Pesados , Microfluídica , Electrodos de Iones Selectos , Plomo , PotenciometríaRESUMEN
As bromate removal and reduction can be also achieved using metals, aluminum (Al) appears as the most promising one for reduction of bromate because Al is abundant element and exhibits a high reduction power. Reactions between bromate and Al shall be even enhanced through ultrasound (US) process because US can facilitate mass transfer on liquid/solid interfaces and clean surfaces via generating microscale turbulence to facilitate reactions. Therefore, the aim of this study is for the first time to investigate the effect of US on bromate removal by Al metal. Specifically, Al particle would be treated by HCl to afford HCl-treated Al (HCTAL), which is capable of removing bromate and even reducing it to bromide. Such a mechanism is also validated by density function theory calculation through determining adsorption energy as -152.8 kJ/mole, and oxygen atoms of bromate would be extracted and reacted with Al atoms, releasing bromide ion. US not only facilitated bromate removal by further increasing removal capacity under the acidic condition but also suppressed the inhibitive effect from basicity at relatively high pH. The spent HCTAL could still remove bromate and convert it to bromide after regeneration. These features indicate that US considerably enhances bromate removal by Al. PRACTITIONER POINTS: Bromate removed by Al is elucidated by DFT calculation with Eabsorption = -152.8 kJ/mole. Oxygen atoms of bromate are extracted and reacted with Al atoms, releasing bromide ion. A higher power of ultrasound would substantially enhance bromate removal efficiency. Ultrasound also suppresses the inhibitive effect from basicity at relatively high pH. With ultrasound, the interference of co-existing anions on bromate removal is lessened.