RESUMEN
Axial suspension plasma spraying (ASPS) is an alternative technique to atmospheric plasma spraying (APS), which uses a suspension of much finer powders (<5-micron particle size) as the feedstock. It can produce more refined microstructures than APS for biomedical implants. This paper highlights the influence of incorporated graphene nanoplatelets (GNPs) on the behavior of ASPS hydroxyapatite (HAp) coatings. The characterization of the ASPS coatings (HAp + varying GNP contents) was carried out using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), confocal Raman microscopy (CRM), white light interferometry (WLI), and contact angle measurements. The evaluation of the mechanical properties such as the hardness, roughness, adhesion strength, and porosity was carried out, along with a fretting wear performance. Additionally, the biocompatibility of the Hap + GNP coatings was evaluated using cytotoxicity testing which revealed a decrease in the cell viability from 92.7% to 85.4%, with an increase in the GNP wt.%. The visualization of the cell's components was carried out using SEM and Laser Scanning Microscopy. Furthermore, the changes in the genetic expression of the various cellular markers were assessed to analyze the epigenetic changes in human mesenchymal stem cells. The gene expression changes suggested that GNPs upregulated the proliferation marker and downregulated the pluripotent markers by a minimum of three folds.
RESUMEN
Higher durability in thermal barrier coatings (TBCs) is constantly sought to enhance the service life of gas turbine engine components such as blades and vanes. In this study, three double layered gadolinium zirconate (GZ)-on-yttria stabilized zirconia (YSZ) TBC variants with varying individual layer thickness but identical total thickness produced by suspension plasma spray (SPS) process were evaluated. The objective was to investigate the role of YSZ layer thickness on the durability of GZ/YSZ double-layered TBCs under different thermal cyclic test conditions i.e., thermal cyclic fatigue (TCF) at 1100 °C and a burner rig test (BRT) at a surface temperature of 1400 °C, respectively. Microstructural characterization was performed using SEM (Scanning Electron Microscopy) and porosity content was measured using image analysis technique. Results reveal that the durability of double-layered TBCs decreased with YSZ thickness under both TCF and BRT test conditions. The TBCs were analyzed by SEM to investigate microstructural evolution as well as failure modes during TCF and BRT test conditions. It was observed that the failure modes varied with test conditions, with all the three double-layered TBC variants showing failure in the TGO (thermally grown oxide) during the TCF test and in the ceramic GZ top coat close to the GZ/YSZ interface during BRT. Furthermore, porosity analysis of the as-sprayed and TCF failed TBCs revealed differences in sintering behavior for GZ and YSZ. The findings from this work provide new insights into the mechanisms responsible for failure of SPS processed double-layered TBCs under different thermal cyclic test conditions.
RESUMEN
Dissolution of atmospheric plasma sprayed (APS) hydroxyapatite (HAp) coatings on Ti-6Al-4 V medical implants have always been a challenge to overcome in the field of biomedical industry. In the present work, an attempt has been made to develop a HAp coating using a novel thermal spray process called axial suspension plasma spraying (SPS), which leads to thin adherent coatings. Two HAp coatings fabricated by APS (P1 and P2) and four SPS HAp coatings (S1, S2, S3 and S4) produced with varying spraying parameters were characterized in terms of (1) microstructure, porosity, hardness, adhesion strength, contact angle and phase purity; (2) corrosion resistance in 10% Fetal bovine serum (FBS); (3) in-vitro cell adherence and cell viability using human umbilical cord blood-derived mesenchymal stem cells (hMSCs). Amongst different APS and SPS coatings, P1 and S3 exhibited superior properties. S3 coating developed using SPS exhibited 1.3 times higher adhesion strength when compared to APS coating (P1) and 9.5 times higher corrosion resistance than P1. In addition, both S3 and P1 exhibited comparatively higher biocompatibility as evidenced by the presence of more than 92% viable hMSCs.