Sub-surface Imaging of Porous GaN Distributed Bragg Reflectors via Backscattered Electrons.

In this article, porous GaN distributed Bragg reflectors (DBRs) were fabricated by epitaxy of undoped/doped multilayers followed by electrochemical etching. We present backscattered electron scanning electron microscopy (BSE-SEM) for sub-surface plan-view imaging, enabling efficient, non-destructive pore morphology characterization. In mesoporous GaN DBRs, BSE-SEM images the same branching pores and Voronoi-like domains as scanning transmission electron microscopy. In microporous GaN DBRs, micrographs were dominated by first porous layer features (45 nm to 108 nm sub-surface) with diffuse second layer (153 nm to 216 nm sub-surface) contributions. The optimum primary electron landing energy (LE) for image contrast and spatial resolution in a Zeiss GeminiSEM 300 was approximately 20 keV. BSE-SEM detects porosity ca. 295 nm sub-surface in an overgrown porous GaN DBR, yielding low contrast that is still first porous layer dominated. Imaging through a ca. 190 nm GaN cap improves contrast. We derived image contrast, spatial resolution, and information depth expectations from semi-empirical expressions. These theoretical studies echo our experiments as image contrast and spatial resolution can improve with higher LE, plateauing towards 30 keV. BSE-SEM is predicted to be dominated by the uppermost porous layer's uppermost region, congruent with experimental analysis. Most pertinently, information depth increases with LE, as observed.

Carrier dynamics at trench defects in InGaN/GaN quantum wells revealed by time-resolved cathodoluminescence.

Time-resolved cathodoluminescence offers new possibilities for the study of semiconductor nanostructures - including defects. The versatile combination of time, spatial, and spectral resolution of the technique can provide new insights into the physics of carrier recombination at the nanoscale. Here, we used power-dependent cathodoluminescence and temperature-dependent time-resolved cathodoluminescence to study the carrier dynamics at trench defects in InGaN quantum wells - a defect commonly found in III-nitride structures. The measurements show that the emission properties of trench defects closely relate to the depth of the related basal plane stacking fault within the quantum well stack. The study of the variation of carrier decay time with detection energy across the emission spectrum provides strong evidence supporting the hypothesis that strain relaxation of the quantum wells enclosed within the trench promotes efficient radiative recombination even in the presence of an increased indium content. This result shines light on previously reported peculiar emission properties of the defect, and illustrates the use of cathodoluminescence as a powerful adaptable tool for the study of defects in semiconductors.

Crystalline Interlayers for Reducing the Effective Thermal Boundary Resistance in GaN-on-Diamond.

Integrating diamond with GaN high electron mobility transistors (HEMTs) improves thermal management, ultimately increasing the reliability and performance of high-power high-frequency radio frequency amplifiers. Conventionally, an amorphous interlayer is used before growing polycrystalline diamond onto GaN in these devices. This layer contributes significantly to the effective thermal boundary resistance (TBReff) between the GaN HEMT and the diamond, reducing the benefit of the diamond heat spreader. Replacing the amorphous interlayer with a higher thermal conductivity crystalline material would reduce TBReff and help to enable the full potential of GaN-on-diamond devices. In this work, a crystalline Al0.32Ga0.68N interlayer has been integrated into a GaN/AlGaN HEMT device epitaxy. Two samples were studied, one with diamond grown directly on the AlGaN interlayer and another incorporating a thin crystalline SiC layer between AlGaN and diamond. The TBReff, measured using transient thermoreflectance, was improved for the sample with SiC (30 ± 5 m2 K GW-1) compared to the sample without (107 ± 44 m2 K GW-1). The reduced TBReff is thought to arise from improved adhesion between SiC and the diamond compared to the diamond directly on AlGaN because of an increased propensity for carbide bond formation between SiC and the diamond. The stronger carbide bonds aid transmission of phonons across the interface, improving heat transport.

Integrated Wafer Scale Growth of Single Crystal Metal Films and High Quality Graphene.

We report on an approach to bring together single crystal metal catalyst preparation and graphene growth in a combined process flow using a standard cold-wall chemical vapor deposition (CVD) reactor. We employ a sandwich arrangement between a commercial polycrystalline Cu foil and c-plane sapphire wafer and show that close-spaced vacuum sublimation across the confined gap can result in an epitaxial, single-crystal Cu(111) film at high growth rate. The arrangement is scalable (we demonstrate 2″ wafer scale) and suppresses reactor contamination with Cu. While starting with an impure Cu foil, the freshly prepared Cu film is of high purity as measured by time-of-flight secondary ion mass spectrometry. We seamlessly connect the initial metallization with subsequent graphene growth via the introduction of hydrogen and gaseous carbon precursors, thereby eliminating contamination due to substrate transfer and common lengthy catalyst pretreatments. We show that the sandwich approach also enables for a Cu surface with nanometer scale roughness during graphene growth and thus results in high quality graphene similar to previously demonstrated Cu enclosure approaches. We systematically explore the parameter space and discuss the opportunities, including subsequent dry transfer, generality, and versatility of our approach particularly regarding the cost-efficient preparation of different single crystal film orientations and expansion to other material systems.

A Peeling Approach for Integrated Manufacturing of Large Monolayer h-BN Crystals.

Hexagonal boron nitride (h-BN) is the only known material aside from graphite with a structure composed of simple, stable, noncorrugated atomically thin layers. While historically used as a lubricant in powder form, h-BN layers have become particularly attractive as an ultimately thin insulator, barrier, or encapsulant. Practically all emerging electronic and photonic device concepts currently rely on h-BN exfoliated from small bulk crystallites, which limits device dimensions and process scalability. We here focus on a systematic understanding of Pt-catalyzed h-BN crystal formation, in order to address this integration challenge for monolayer h-BN via an integrated chemical vapor deposition (CVD) process that enables h-BN crystal domain sizes exceeding 0.5 mm and a merged, continuous layer in a growth time of less than 45 min. The process makes use of commercial, reusable Pt foils and allows a delamination process for easy and clean h-BN layer transfer. We demonstrate sequential pick-up for the assembly of graphene/h-BN heterostructures with atomic layer precision, while minimizing interfacial contamination. The approach can be readily combined with other layered materials and enables the integration of CVD h-BN into high-quality, reliable 2D material device layer stacks.

Characterisation of InGaN by Photoconductive Atomic Force Microscopy.

Nanoscale structure has a large effect on the optoelectronic properties of InGaN, a material vital for energy saving technologies such as light emitting diodes. Photoconductive atomic force microscopy (PC-AFM) provides a new way to investigate this effect. In this study, PC-AFM was used to characterise four thick (∼130 nm) In x Ga 1 - x N films with x = 5%, 9%, 12%, and 15%. Lower photocurrent was observed on elevated ridges around defects (such as V-pits) in the films with x ≤ 12 %. Current-voltage curve analysis using the PC-AFM setup showed that this was due to a higher turn-on voltage on these ridges compared to surrounding material. To further understand this phenomenon, V-pit cross sections from the 9% and 15% films were characterised using transmission electron microscopy in combination with energy dispersive X-ray spectroscopy. This identified a subsurface indium-deficient region surrounding the V-pit in the lower indium content film, which was not present in the 15% sample. Although this cannot directly explain the impact of ridges on turn-on voltage, it is likely to be related. Overall, the data presented here demonstrate the potential of PC-AFM in the field of III-nitride semiconductors.

Dislocations in AlGaN: Core Structure, Atom Segregation, and Optical Properties.

We conducted a comprehensive investigation of dislocations in Al0.46Ga0.54N. Using aberration-corrected scanning transmission electron microscopy and energy dispersive X-ray spectroscopy, the atomic structure and atom distribution at the dislocation core have been examined. We report that the core configuration of dislocations in AlGaN is consistent with that of other materials in the III-Nitride system. However, we observed that the dissociation of mixed-type dislocations is impeded by alloying GaN with AlN, which is confirmed by our experimental observation of Ga and Al atom segregation in the tensile and compressive parts of the dislocations, respectively. Investigation of the optical properties of the dislocations shows that the atom segregation at dislocations has no significant effect on the intensity recorded by cathodoluminescence in the vicinity of the dislocations. These results are in contrast with the case of dislocations in In0.09Ga0.91N where segregation of In and Ga atoms also occurs but results in carrier localization limiting non-radiative recombination at the dislocation. This study therefore sheds light on why InGaN-based devices are generally more resilient to dislocations than their AlGaN-based counterparts.