RESUMEN
A triple-band microstrip patch antenna designed for the IEEE 802.16e WiMAX, IEEE 802.11a WLAN, C-band downlink communications, and Ku-band radar recent applications is suggested in this article. The planned antenna operates at 2.45, 6, and 14 GHz resonant frequencies. The antenna fulfilled triple-band physical characteristics covering industrial, scientific, and medical (ISM) bands between (2.1-2.8) GHz; (5.6-6.5) GHz for wireless local area network (WLAN) or ultra-wideband (UWB) services; and 12.7-16 GHz for future two-way 5G:6G either broadcasting or mobile satellite communications. To achieve better return loss performance, parametric studies are carried out using Microwave Studio (CST MWS). The proposed antenna is designed on the FR4 as a hosting medium of total size 46 × 38 × 1.6 mm3, combined with a planar transmission line (T.L.) feed and defected ground structure (DGS). The simulated antenna's input reflection coefficient (S11) results and the far-field measurements show good agreement. The fabricated prototype achieves peak gain values of 2.8, 3.8, and 4.7 dBi, respectively, and bidirectional radiation characteristics. A comparative study with other recent publications is implemented to validate the consistency of the design.
RESUMEN
A pattern reconfigurable antenna, composed of eight elements, is proposed for energy harvesting applications. Pattern reconfigurable antennas are a promising technique for harvesting from different wireless sources. The radiation pattern of the proposed antenna can be steered electronically using an RF switch matrix, covering an angle range from 0 to 360 degrees with a step size of 45 degrees. The proposed antenna primarily consists of an eight-dipole configuration that shares the same excitation. Each dipole is excited using a balun comprising a quarter-wavelength grounded stub and a quarter-wavelength open-circuit stub. The proposed antenna operates in the frequency range of 4.17 to 4.5 GHz, with an impedance bandwidth of 7.6%. By switching between the different switches, the antenna can be steered with a narrower rotational angle. In addition, the antenna can work in an omnidirectional mode when all switches are in the ON state simultaneously. The results demonstrate a good agreement between the numerical and experimental findings for the reflection coefficient and radiation characteristics of the proposed reconfigurable antenna.
RESUMEN
This paper presents a single-substrate microstrip rectenna for dedicated radio frequency energy harvesting applications. The proposed configuration of the rectenna circuit is composed of a clipart moon-shaped cut in order to improve the antenna impedance bandwidth. The curvature of the ground plane is modified with a simple U-shaped slot etched into it to improve the antenna bandwidth by changing the current distribution; therefore, this affects the inductance and capacitance embedded into the ground plane. The linear polarized ultra-wide bandwidth (UWB) antenna is achieved by using 50 Ω microstrip line and build on Roger 3003 substrate with an area of 32 × 31 mm2. The operating bandwidth of the proposed UWB antenna extended from 3 GHz to 25 GHz at -6 dB reflection coefficient (VSWR ≤ 3) and extended from both 3.5 to 12 GHz, from 16 up to 22 GHz at -10 dB impedance bandwidth (VSWR ≤ 2). This was used to harvest RF energy from most of the wireless communication bands. In addition, the proposed antenna integrates with the rectifier circuit to create the rectenna system. Moreover, to implement the shunt half-wave rectifier (SHWR) circuit, a planar Ag/ZnO Schottky diode uses a diode area of 1 × 1 mm2. The proposed diode is investigated and designed, and its S-parameter is measured for use in the circuit rectifier design. The proposed rectifier has a total area of 40 × 9 mm2 and operates at different resonant frequencies, namely 3.5 GHz, 6 GHz, 8 GHz, 10 GHz and 18 GHz, with a good agreement between simulation and measurement. The maximum measured output DC voltage of the rectenna circuit is 600 mV with a maximum measured efficiency of 25% at 3.5 GHz, with an input power level of 0 dBm at a rectifier load of 300 Ω.
RESUMEN
This paper proposes a flexible, frequency-reconfigurable monopole antenna design with frequency selective surface (FSS) for Internet of Things (IoT) applications. The proposed antenna operates at three of the IoT frequency bands. This antenna is a coplanar waveguide (CPW)-fed monopole with two balanced arms printed on a thin ROGERS 3003 flexible substrate. The length of the right-hand arm of the antenna is used to achieve frequency reconfiguration by using PIN diodes. Three frequency modes of operation have been obtained; the 2.4 GHz frequency band with the right-hand arm is fully truncated, the 3.5 GHz frequency band with the two arms is completely maintained, and the 4 GHz frequency band with the right-hand arm is partially truncated. To improve the gain of the antenna, a simple FSS surface is designed to be placed under the antenna at a distance of 15 mm. The FSS operates efficiently from 2 to 4.5 GHz and has improved the gain of the antenna. A maximum gain of 6.5 dBi, 7.52 dBi, and 7.91 dBi has been achieved at the three frequency bands respectively. The behavior of the flexible antenna has been evaluated in both the flat and bent states, and stable performance has been observed in both cases.
RESUMEN
In this work, a spectrum-sensing monopole antenna was used to operate in different frequency bands for cognitive radio applications. The proposed antenna consists of a folded monopole antenna with a partial ground plane, and it can be used for various wireless technologies operated at various frequencies from 1.5 to 3.5 GHz. The suggested antenna was printed on a RO4003 substrate with 3.38 permittivity and an overall size of 60 × 60 × 0.813 mm3. To achieve reconfigurability of the antenna, PIN diodes (HPND-4005) were inserted at different lengths along the antenna to obtain the desired performance. The antenna was fabricated and experimentally tested to validate the simulation outcomes, and distinct consistency between the simulation and measurement outcomes was obtained. Computer simulation tool (CST) software was used to design and simulate the suggested antenna and then the model was fabricated to validate the simulation outcomes.
RESUMEN
A reconfigurable wideband monopole antenna is introduced in this paper for cognitive radio and wireless applications. The reconfigurability was achieved by four varactor diodes embedded in the band pass filter (BPF) structure which was integrated with the suggested antenna through its feed line. The simulated impedance characteristics coped with the measured ones after fabricating the suggested model with/without the reconfigurable BPF. Furthermore, the model achieved the desired radiation characteristics in terms of radiation pattern with acceptable gain values at the selected frequencies within the achieved frequency range (1.3-3 GHz).