Enhancing Permeability: Unraveling the Potential of Microporous Organic Polymers in Mixed Matrix Membranes.

Mixed matrix membranes (MMMs) were formed by using seven polymeric matrices with a wide range of permeabilities. All of the polymeric matrices have been polyimides, namely: P84, Pi-DAPOH, Pi-DAROH, Matrimid, Pi-HABAc, PI-DAM, and PIM-1 in the order of increasing O2 permeability. A fixed (10%) concentration of a microporous organic polymer (TFAP-Trp), formed by the combination of trifluoroacetophenone and triptycene, was added as a porous filler. The material properties as well as their separation performances for multiple pure gases, specifically the permeabilities of He, N2, O2, CH4, and CO2, were measured. The correlation between the relative increase in permeability in MMMs and that of the matrix polymeric membrane has been quantitatively analyzed. This study proves that the increased permeability of MMMs is largely linked to the contribution of the high permeability of the filler. The addition of the TFAP-Trp porous filler proves to be especially beneficial for matrices with low to moderate permeabilities, significantly enhancing the matrix permeability overall. The fitted relationship is approximately linear in accordance with the existing models to predict permeability in dual-phase systems for low proportions of the dispersed phase. An extrapolation allows the evaluation of the permeability of the pure microporous organic polymer, which agrees with the previous values described by the group for different filler contents and in other polymeric matrices. In all cases, the selectivity remains approximately constant while the permeability increases. The addition of TFAP-Trp to all the polymeric matrices led to a moderate improvement of the MMM separation performances, mainly centered on their permeabilities.

Morphological Study before and after Thermal Treatment of Polymer-Polymer Mixed-Matrix Membranes for Gas Separations.

A good integration of the polymer materials that form a mixed-matrix membrane (MMM) for gas separation is essential to reaching interesting permselective properties. In this work, a porous polymer network (PPN), obtained by combining triptycene and trifluoroacetophenone, has been used as a filler, which was blended with two o-hydroxypolyamides (HPAs) that act as polymer matrices. These polymer matrices have been thermally treated to induce a thermal rearrangement (TR) of the HPAs to polybenzoxazoles (ß-TR-PBOs) through a solid-state reaction. For its structural study, various techniques have been proposed that allow us to undertake a morphological investigation into the integration of these materials. To access the internal structure of the MMMs, three different methods were used: a polishing process for the material surface, the partial dissolution of the polymer matrix, or argon plasma etching. The argon plasma technique has not only revealed its potential to visualize the internal structure of these materials; it has also been proven to allow for the transformation of their permselective properties. Force modulation and phase contrast in lift-mode techniques, along with the topographic images obtained via the tapping mode using a scanning probe microscope (SPM), have allowed us to study the distribution of the filler particles and the interaction of the polymer and the filler. The morphological information obtained via SPM, along with that of other more commonly used techniques (SEM, TGA, DSC, FTIR, WASX, gas adsorption, and permeability measurements), has allowed us to postulate the most probable structural configuration in this type of system.

New benzimidazole derivative compounds with in vitro fasciolicidal properties.

BACKGROUND: Control of the zoonotic food-borne parasite Fasciola hepatica remains a major challenge in humans and livestock. It is estimated that annual economic losses due to fasciolosis can reach US$3.2 billion in agriculture and livestock. Moreover, the wide distribution of drug-resistant parasite populations and the absence of a vaccine threaten sustainable control, reinforcing the need for novel flukicides. METHODS: The present work analyses the flukicidal activity of a total of 70 benzimidazole derivatives on different stages of F. hepatica. With the aim to select the most potent ones, and screenings were first performed on eggs at decreasing concentrations ranging from 50 to 5 µM and then on adult worms at 10 µM. Only the most effective compounds were also evaluated using a resistant isolate of the parasite. RESULTS: After the first screenings at 50 and 10 µM, four hit compounds (BZD31, BZD46, BZD56, and BZD59) were selected and progressed to the next assays. At 5 µM, all hit compounds showed ovicidal activities higher than 71% on the susceptible isolate, but only BZD31 remained considerably active (53%) when they were tested on an albendazol-resistant isolate, even with values superior to the reference drug, albendazole sulfoxide. On the other hand, BZD59 displayed a high motility inhibition when tested on adult worms from an albendazole-resistant isolate after 72 h of incubation. CONCLUSIONS: BZD31 and BZD59 compounds could be promising candidates for the development of fasciolicidal compounds or as starting point for the new synthesis of structure-related compounds.

Analysis of Healthcare-associated Infections before and during the COVID-19 pandemic in a Colombian hospital

Introduction: Healthcare-associated infections pose a significant challenge, contributing to hospital morbidity and mortality. Objective: To describe the behavior of Healthcare Associated Infections before and during the pandemic reported to a high-complexity health institution in Colombia. Material and Methods: In our retrospective observational study on Healthcare-Associated Infections (HAIs), we analyzed data from all in-patients diagnosed with HAIs between 2018 and 2020. This included clinical, demographic, microbiological, and microbial susceptibility information collected from the Committee on Nosocomial Infections' prospective database. Data from 391 isolates were obtained using Whonet software for antimicrobial resistance surveillance. Results: We found 504 cases of HAIs (2018-2020) with an overall in-hospital infection rate of 2.55/1000 patient-days. The median age for pediatric patients was 5 years, and for adults, 56 years, with 57% male. The leading admission diagnoses were oncologic disease complications (31%). Bacteremia had a 30-day mortality rate of 13%, predominantly catheter-associated (37%). Gram-negative bacilli, notably Klebsiella pneumoniae, Escherichia coli, and Pseudomonas aeruginosa, represented 58% cases of HAI. Discussion: The critical need for specific interventions and antimicrobial management to control HAIs, especially given the challenges posed by the COVID-19 pandemic, is highlighted. Conclusions: This is the first report on HAIs incidence at a tertiary hospital in Bucaramanga, Santander (Colombia). Bacteremia was predominant; 75% of HAIs patients had comorbidities. Gram-negative bacilli prevailed; a notable rise in ICU respiratory infections occurred during the 2020 COVID-19 pandemic. Resistance to cephalosporins and carbapenems was prevalent.

Behavior and Use of Quaternary Ammonium-Based Disinfectants in Biosafety Protocols Against Fusarium oxysporum f. sp. cubense Race 1 and Tropical Race 4.

The banana is one of Colombia's main export products. However, production is seriously affected by Fusarium wilt of banana, which is the most destructive disease caused by the fungus Fusarium oxysporum f. sp. cubense tropical race 4 (Foc TR4). Currently, management strategies focus on containment and biosecurity protocols to prevent its spread to territories that are free of this disease. This study aimed to evaluate nine quaternary ammonium-based disinfectants (i.e., quaternary ammonium compounds [QACs]) in vitro in Colombia on reproductive (microconidia and macroconidia) and resistance structures (chlamydospores) of Foc race 1 (R1) and tropical race 4 (TR4), with and without soil, to determine the influence of organic matter and soil texture on the action of QACs. A method for inhibiting the action of QACs was standardized and evaluated at 1,200 ppm with a contact time of ≤30 s while evaluating the soil-inoculum and soil-disinfectant interactions. In the soil-inoculum interaction, the efficacy of QACs was 100% in the reproductive and resistance structures of Foc R1 and TR4 without soil. However, in the soil-disinfectant interaction, only QAC4 controlled the pathogen at 100%. The presence of organic matter influenced the biocidal action of the QACs, and fine textures had a greater reducing effect on the concentration. The soil decreased the efficacy of the QACs and, therefore, must be removed from contaminated boots before treatments are applied.

Air Pollution and Cardiac Diseases: A Review of Experimental Studies.

Air pollution is associated with around 6.5 million premature deaths annually, which are directly related to cardiovascular diseases, and the most dangerous atmospheric pollutants to health are as follows: NO2, SO2, CO, and PM. The mechanisms underlying the observed effects have not yet been clearly defined. This work aims to conduct a narrative review of experimental studies to provide a more comprehensive and multiperspective assessment of how the effect of atmospheric pollutants on cardiac activity can result in the development of cardiac diseases. For this purpose, a review was carried out in databases of experimental studies, excluding clinical trials, and epidemiological and simulation studies. After analyzing the available information, the existence of pathophysiological effects of the different pollutants on cardiac activity from exposure during both short-term and long-term is evident. This narrative review based on experimental studies is a basis for the development of recommendations for public health.

Characterization of airborne particulate matter and its toxic and proarrhythmic effects: A case study in Aburrá Valley, Colombia.

Particle matter (PM) is a complex mixture of particles suspended in the air, mainly caused by fuel combustion from vehicles and industry, and has been related to pulmonary and cardiovascular diseases. The Metropolitan Area of Aburrá Valley in Colombia is the second most populous urban agglomeration in the country and the third densest in the world, composed of ten municipalities. Examining the physicochemical properties of PM is crucial in comprehending its composition and its effects on human health, as it varies based on the socioeconomic dynamics specific to each city. This study characterized the PM collected from the north, south, and central zones to evaluate its chemical composition and morphology. Different elements such as silicon, carbon, aluminum, potassium, calcium, sodium, iron, magnesium, and copper and the presence of unburned fuel, motor oil, and silicon fibers were identified. In vitro and in silico studies were conducted to evaluate the toxicity of the PM, and it was found that the PM collected from the central zone had the greatest impact on cell viability and caused DNA damage. The in silico study demonstrated that PM has concentration-dependent proarrhythmic effects, reflected in an action potential duration shortening and an increased number of reentries, which may contribute to the development of cardiac arrhythmias. Overall, the results suggest that the size and chemical composition of ambient PM can induce toxicity and play an important role in the generation of arrhythmias.

Secretory IgA as Biomarker for Gastrointestinal Nematodes Natural Infection in Different Breed Sheep.

Specific IgA antibody has been shown to play an important role in resistance to gastrointestinal nematode (GIN) infections in sheep, particularly in Teladorsagia circumcincta parasitosis. In some breeds, negative associations have been shown between IgA levels and worm burden in experimentally infected sheep. In the present study, we have studied the relationship between IgA levels in naturally infected sheep (582 ewes in total; 193 younger than one year old and 389 older than one year old) and fecal egg count (FEC) in the Assaf, Castellana, and Churra breeds. ELISA assays were performed to measure IgA levels against the somatic antigen of T. circumcincta third larval stage (L3) and a 203-amino-acid fragment of the protein disulfide isomerase from the same GIN species. A multilevel random intercept model was developed to predict the infection risk according to age or breed. Spearman's correlation rank was used for statistical analysis. The prediction model showed that breed was not an influential factor in this study, although the Assaf breed could be considered slightly more susceptible than the others. In addition, age affected the infection risk, with the young ewes more susceptible to infection than the adult groups, except for the Castellana breed, whose risk of infection was similar at all ages. The most significant positive association was found between FEC and IgA measured in the nasal secretions of young ewes using both antigens (Rho = 0.5; p = 0.00); the correlation of FEC with IgA in serum was moderately significant (Rho = 0.306; p = 0.00). Comparing both antigens, the protein disulfide isomerase antigen was less reactive than the somatic antigen from L3. In conclusion, under natural conditions, specific IgA against GIN was positively associated with FEC in sheep, with nasal secretions from young animals being the sample where this association is stronger, which, therefore, could be used as a marker of infection in further studies.

Forward Osmosis Application for the Removal of Emerging Contaminants from Municipal Wastewater: A Review.

Forward osmosis (FO) has attracted special attention in water and wastewater treatment due to its role in addressing the challenges of water scarcity and contamination. The presence of emerging contaminants in water sources raises concerns regarding their environmental and public health impacts. Conventional wastewater treatment methods cannot effectively remove these contaminants; thus, innovative approaches are required. FO membranes offer a promising solution for wastewater treatment and removal of the contaminants in wastewater. Several factors influence the performance of FO processes, including concentration polarization, membrane fouling, draw solute selection, and reverse salt flux. Therefore, understanding and optimizing these factors are crucial aspects for improving the efficiency and sustainability of the FO process. This review stresses the need for research to explore the potential and challenges of FO membranes to meet municipal wastewater treatment requirements, to optimize the process, to reduce energy consumption, and to promote scalability for potential industrial applications. In conclusion, FO shows promising performance for wastewater treatment, dealing with emerging pollutants and contributing to sustainable practices. By improving the FO process and addressing its challenges, we could contribute to improve the availability of water resources amid the global water scarcity concerns, as well as contribute to the circular economy.

Saline Retention and Permeability of Nanofiltration Membranes Versus Resistance and Capacitance as Obtained from Impedance Spectroscopy under a Concentration Gradient.

Impedance spectroscopy has been widely used for the study of the electrical properties of membranes for their characterization. The most common use of this technique is the measure of the conductivity of different electrolyte solutions to study the behavior and movement of electrically charged particles inside the pores of membranes. The objective of this investigation was to observe if there is a relation present between the retention that a nanofiltration membrane possesses to certain electrolytic solutions (NaCl, KCl, MgCl2, CaCl2, and Na2SO4) and the parameters that are obtained through IS measurements of the active layer of the membrane. To achieve our objective, different characterization techniques were performed to obtain the permeability, retention, and zeta potential values of a Desal-HL nanofiltration membrane. Impedance spectroscopy measurements were performed when a gradient concentration was present between both sides of the membrane to study the variation that the electrical parameters had with the time evolution.

Evaluation of Forward Osmosis and Low-Pressure Reverse Osmosis with a Tubular Membrane for the Concentration of Municipal Wastewater and the Production of Biogas.

Currently, freshwater scarcity is one of the main issues that the world population has to face. To address this issue, new wastewater treatment technologies have been developed such as membrane processes. Among them, due to the energy disadvantages of pressure-driven membrane processes, Forward Osmosis (FO) and Low-Pressure Reverse Osmosis (LPRO) have been introduced as promising alternatives. In this study, the behavior of a 2.3 m2 tubular membrane TFO-D90 when working with municipal wastewater has been studied. Its performances have been evaluated and compared in two operating modes such as FO and LPRO. Parameters such as fouling, flow rates, water flux, draw solution concentration, organic matter concentration, as well as its recovery have been studied. In addition, the biogas production capacity has been evaluated with the concentrated municipal wastewater obtained from each process. The results of this study indicate that the membrane can work in both processes (FO and LPRO) but, from the energy and productivity point of view, FO is considered more appropriate mainly due to its lower fouling level. This research may offer a new point of view on low-energy and energy recovery wastewater treatment and the applicability of FO and LPRO for wastewater concentration.

Isomeric Aromatic Polyimides Containing Biphenyl Moieties for Gas Separation Applications.

An optimized synthesis of the monomer 2,2'3,3'-biphenyltetracarboxylic dianhydride, iBPDA, was performed to obtain high molecular weight polymers. This monomer has a contorted structure that produces a non-linear shape, hindering the packing of the polymer chain. Aromatic polyimides of high molecular weight were obtained by reaction with the commercial diamine 2,2-bis(4-aminophenyl) hexafluoropropane, 6FpDA, which is a very common monomer in gas separation applications. This diamine has hexafluoroisopropylidine groups which introduce rigidity in the chains, hindering efficient packing. The thermal treatment of the polymers processed as dense membranes had two targets: on the one hand, to achieve the complete elimination of the solvent used, which could remain occluded in the polymeric matrix, and on the other hand to ensure the complete cycloimidization of the polymer. A thermal treatment exceeding the glass transition temperature was performed to ensure the maximum degree of imidization at 350 °C. The good mechanical properties of these materials allow for their use in high-pressure gas purification applications. Moreover, models of the polymers exhibited an Arrhenius-like behavior characteristic of secondary relaxations, normally associated with local motions of the molecular chain. The gas productivity of these membranes was high.

Gas Permeability through Polyimides: Unraveling the Influence of Free Volume, Intersegmental Distance and Glass Transition Temperature.

The relationships between gas permeability and free volume fraction, intersegmental distance, and glass transition temperature, are investigated. They are analyzed for He, CO2, O2, CH4, and N2 gases and for five similar polyimides with a wide range of permeabilities, from very low to extremely high ones. It has been established here that there is an exponential relationship between permeability and the free volume fraction, and between permeability and the most probable intersegmental distance as measured by WAXS; in both cases, with an exponential coefficient that depends on the kinetic gas diameter as a quadratic polynomial and with a preexponential positive constant. Moreover, it has been proven that the intersegmental distance increases linearly with the free volume fraction. Finally, it has been established that the free volume fraction increases with the glass transition temperature for the polymers tested, and that they depend on each other in an approximate linear way.

Thermally Rearranged Mixed Matrix Membranes from Copoly(o-hydroxyamide)s and Copoly(o-hydroxyamide-amide)s with a Porous Polymer Network as a Filler-A Comparison of Their Gas Separation Performances.

Copoly(o-hydroxyamide)s (HPA) and copoly(o-hydroxyamide-amide)s (PAA) have been synthesized to be used as continuous phases in mixed matrix membranes (MMMs). These polymeric matrices were blended with different loads (15 and 30 wt.%) of a relatively highly microporous porous polymer network (PPN). SEM images of the manufactured MMMs exhibited good compatibility between the two phases for all the membranes studied, and their mechanical properties have been shown to be good enough even after thermal treatment. The WAX results show that the addition of PPN as a filler up to 30% does not substantially change the intersegmental distance and the polymer packing. It seems that, for all the membranes studied, the free volume that determines gas transport is in the high end of the possible range. This means that gas flow occurs mainly between the microvoids in the polymer matrix around the filler. In general, both HPA- and PAA-based MMMs exhibited a notable improvement in gas permeability, due to the presence of PPN, for all gases tested, with an almost constant selectivity. In summary, although the thermal stability of the PAA is limited by the thermal stability of the polyamide side chain, their mechanical properties were better. The permeability was higher for the PAA membranes before their thermal rearrangement, and these values increased after the addition of moderate amounts of PPN.

Free Volume and Permeability of Mixed Matrix Membranes Made from a Terbutil-M-terphenyl Polyamide and a Porous Polymer Network.

A set of thermally rearranged mixed matrix membranes (TR-MMMs) was manufactured and tested for gas separation. These membranes were obtained through the thermal treatment of a precursor MMM with a microporous polymer network and an o-hydroxypolyamide,(HPA) created through a reaction of 2,2-bis(3-amino-4-hydroxyphenyl)-hexafluoropropane (APAF) and 5'-terbutil-m-terfenilo-3,3″-dicarboxylic acid dichloride (tBTmCl). This HPA was blended with different percentages of a porous polymer network (PPN) filler, which produced gas separation MMMs with enhanced gas permeability but with decreased selectivity. The thermal treatment of these MMMs gave membranes with excellent gas separation properties that did not show the selectivity decreasing trend. It was observed that the use of the PPN load brought about a small decrease in the initial mass losses, which were lower for increasing PPN loads. Regarding the glass transition temperature, it was observed that the use of the filler translated to a slightly lower Tg value. When these MMMs and TR-MMMs were compared with the analogous materials created from the isomeric 5'-terbutil-m-terfenilo-4,4″-dicarboxylic acid dichloride (tBTpCl), the permeability was lower for that of tBTmCl, compared with the one from tBTpCl, although selectivity was quite similar. This fact could be attributed to a lower rigidity as roughly confirmed by the segmental length of the polymer chain as studied by WAXS. A model for FFV calculation was proposed and its predictions compared with those evaluated from density measurements assuming a matrix-filler interaction or ideal independence. It turns out that permeability as a function of FFV for TR-MMMs follows an interaction trend, while those not thermally treated follow the non-interaction trend until relatively high PPN loads were reached.

Enhancement of swine manure anaerobic digestion using membrane-based NH3 extraction.

The influence of suspended solids and pH in anaerobically digested piggery wastewater on membrane-based NH3 extraction was evaluated in batch tests. The increase in pH in the anaerobic broth from 8 to 9 resulted in an increase in NH3 removal efficiencies from 15.8 % ± 0.1 % to 20.9 % ± 0.4 % regardless of the suspended solids. The influence of membrane based NH3 extraction on piggery wastewater treatment was also assessed in a CSTR interconnected with PTFE membrane modules. The decrease in TKN concentrations mediated by membrane operation induced an increase in CH4 yield from 380.4 ± 84.9 up to 566.1 ± 7.8 NmLCH4 g VS fed-1. Likewise, COD and VS removal efficiencies significantly increased from 33.0 % ± 2.0 % and 25.7 % ± 2.3 % up to 61.8 % ± 1.3 % and 37.9 % ± 1.8 %, respectively. Interestingly, the decrease in NH3 concentration entailed a complete assimilation of VFA.

Novel compound shows in vivo anthelmintic activity in gerbils and sheep infected by Haemonchus contortus.

The control of gastrointestinal nematodes in livestock is becoming increasingly difficult due to the limited number of available drugs and the rapid development of anthelmintic resistance. Therefore, it is imperative to develop new anthelmintics that are effective against nematodes. Under this context, we tested the potential toxicity of three compounds in mice and their potential anthelmintic efficacy in Mongolian gerbils infected with Haemonchus contortus. The compounds were selected from previous in vitro experiments: two diamine (AAD-1 and AAD-2) and one benzimidazole (2aBZ) derivatives. 2aBZ was also selected to test its efficacy in sheep. In Mongolian gerbils, the benzimidazole reduced the percentage of pre-adults present in the stomach of gerbils by 95% at a dose of 200 mg/kg. In sheep, there was a 99% reduction in the number of eggs shed in faeces after 7 days at a dose of 120 mg/kg and a 95% reduction in the number of worm adults present in the abomasum. In conclusion, 2aBZ could be considered a promising candidate for the treatment of helminth infections in small ruminants.

Membrane Dialysis for Partial Dealcoholization of White Wines.

Membrane dialysis is studied as a promising technique for partial dealcoholization of white wines. The performance of three membrane processes applied for the partial dealcoholization of white wines of the Verdejo variety has been studied in the present work. Combination of Nanofiltration with Pervaporation, single step Pervaporation and, finally, Dialysis, have been applied to white wines from same variety and different vintages. The resulting wines have been chemically and sensorially analyzed and results have been compared with initial characteristics of the wines. From the results obtained, we can conclude that all procedures lead to significant alcohol content reduction (2%, 0.9% and 1.23% v/v respectively). Nevertheless, the best procedure consists in the application of Dialysis to the wines which resulted in a reasonable alcohol content reduction while maintaining organoleptic properties (only 14 consumers were able to distinguish the filtered and original wines, with 17 consumers needed to be this differences significant) and consumer acceptability of the original wine. Therefore, membrane dialysis, as a method of partial dealcoholization of white wines, has undoubted advantages over other techniques based on membranes, which must be confirmed in subsequent studies under more industrial conditions. This work represents the first application of Dialysis for the reduction of alcohol content in wines.

Ecological Risk Evaluation and Removal of Emerging Pollutants in Urban Wastewater by a Hollow Fiber Forward Osmosis Membrane.

Forward osmosis (FO) is a promising technology for the treatment of urban wastewater. FO can produce high-quality effluents and preconcentrate urban wastewater for subsequent anaerobic treatment. This membrane technology makes it possible to eliminate the pollutants present in urban wastewater, which can cause adverse effects in the ecosystem even at low concentrations. In this study, a 0.6 m2 hollow fiber aquaporin forward osmosis membrane was used for the treatment of urban wastewater from the Valladolid wastewater treatment plant (WWTP). A total of 51 Contaminants of Emerging Concern (CECs) were investigated, of which 18 were found in the target urban wastewater. They were quantified, and their ecotoxicological risk impact was evaluated. Different salts with different concentrations were tested as draw solutions to evaluate the membrane performances when working with pretreated urban wastewater. NaCl was found to be the most appropriate salt since it leads to higher permeate fluxes and lower reverse saline fluxes. The membrane can eliminate or significantly reduce the pollutants present in the studied urban wastewater, producing water without ecotoxicological risk or essentially free of pollutants. In all cases, good recovery was achieved, which increased with molecular weight, although chemical and electrostatic interactions also played a role.

Gas Permeability, Fractional Free Volume and Molecular Kinetic Diameters: The Effect of Thermal Rearrangement on ortho-hydroxy Polyamide Membranes Loaded with a Porous Polymer Network.

Mixed-matrix membranes (MMMs) consisting of an ortho-hydroxy polyamide (HPA) matrix, and variable loads of a porous polymer network (PPN) were thermally treated to induce the transformation of HPA to polybenzoxazole (ß-TR-PBO). Two different HPAs were synthesized to be used as a matrix, 6FCl-APAF and tBTpCl-APAF, while the PPN used as a filler was prepared by reacting triptycene and trifluoroacetophenone. The permeability of He, H2, N2, O2, CH4 and CO2 gases through these MMMs are analyzed as a function of the fraction of free volume (FFV) of the membrane and the kinetic diameter of the gas, allowing for the evaluation of the free volume. Thermal rearrangement entails an increase in the FFV. Both before and after thermal rearrangement, the free volume increases with the PPN content very similarly for both polymeric matrices. It is shown that there is a portion of free volume that is inaccessible to permeation (occluded volume), probably due to it being trapped within the filler. In fact, permeability and selectivity change below what could be expected according to densities, when the fraction of occluded volume increases. A higher filler load increases the percentage of inaccessible or trapped free volume, probably due to the increasing agglomeration of the filler. On the other hand, the phenomenon is slightly affected by thermal rearrangement. The fraction of trapped free volume seems to be lower for membranes in which the tBTpCl-APAF is used as a matrix than for those with a 6FCl-APAF matrix, possibly because tBTpCl-APAF could approach the PPN better. The application of an effective medium theory for permeability allowed us to extrapolate for a 100% filler, giving the same value for both thermally rearranged and non-rearranged MMMs. The pure filler could also be extrapolated by assuming the same tendency as in the Robeson's plots for MMMs with low filler content.