Probing Basal and Prismatic Planes of Graphitic Materials for Metal Single Atom and Subnanometer Cluster Stabilization.

Supported metal single atom catalysis is a dynamic research area in catalysis science combining the advantages of homogeneous and heterogeneous catalysis. Understanding the interactions between metal single atoms and the support constitutes a challenge facing the development of such catalysts, since these interactions are essential in optimizing the catalytic performance. For conventional carbon supports, two types of surfaces can contribute to single atom stabilization: the basal planes and the prismatic surface; both of which can be decorated by defects and surface oxygen groups. To date, most studies on carbon-supported single atom catalysts focused on nitrogen-doped carbons, which, unlike classic carbon materials, have a fairly well-defined chemical environment. Herein we report the synthesis, characterization and modeling of rhodium single atom catalysts supported on carbon materials presenting distinct concentrations of surface oxygen groups and basal/prismatic surface area. The influence of these parameters on the speciation of the Rh species, their coordination and ultimately on their catalytic performance in hydrogenation and hydroformylation reactions is analyzed. The results obtained show that catalysis itself is an interesting tool for the fine characterization of these materials, for which the detection of small quantities of metal clusters remains a challenge, even when combining several cutting-edge analytical methods.

Radical Polymer-based Positive Electrodes for Dual-Ion Batteries: Enhancing Performance with γ-Butyrolactone-based Electrolytes.

Dual-ion batteries (DIBs) represent a promising alternative for lithium ion batteries (LIBs) for various niche applications. DIBs with polymer-based active materials, here poly(2,2,6,6-tetramethylpiperidinyl-N-oxyl methacrylate) (PTMA), are of particular interest for high power applications, though they require appropriate electrolyte formulations. As the anion mobility plays a crucial role in transport kinetics, Li salts are varied using the well-dissociating solvent γ-butyrolactone (GBL). Lithium difluoro(oxalate)borate (LiDFOB) and lithium bis(oxalate)borate (LiBOB) improve cycle life in PTMA||Li metal cells compared to other Li salts and a LiPF6- and carbonate-based reference electrolyte, even at specific currents of 1.0 A g-1 (≈10C), whereas LiDFOB reveals a superior rate performance, i. e., ≈90 % capacity even at 5.0 A g-1 (≈50C). This is attributed to faster charge-transfer/mass transport, enhanced pseudo-capacitive contributions during the de-/insertion of the anions into the PTMA electrode and to lower overpotentials at the Li metal electrode.

Laser desorption/ionization-mass spectrometry for the analysis of interphases in lithium ion batteries.

Laser desorption/ionization-mass spectrometry (LDI-MS) is introduced as a complementary technique for the analysis of interphases formed at electrode|electrolyte interfaces in lithium ion batteries (LIBs). An understanding of these interphases is crucial for designing interphase-forming electrolyte formulations and increasing battery lifetime. Especially organic species are analyzed more effectively using LDI-MS than with established methodologies. The combination with trapped ion mobility spectrometry and tandem mass spectrometry yields additional structural information of interphase components. Furthermore, LDI-MS imaging reveals the lateral distribution of compounds on the electrode surface. Using the introduced methods, a deeper understanding of the mechanism of action of the established solid electrolyte interphase-forming electrolyte additive 3,4-dimethyloxazolidine-2,5-dione (Ala-N-CA) for silicon/graphite anodes is obtained, and active electrochemical transformation products are unambiguously identified. In the future, LDI-MS will help to provide a deeper understanding of interfacial processes in LIBs by using it in a multimodal approach with other surface analysis methods to obtain complementary information.

Evaluating a Dual-Ion Battery with an Antimony-Carbon Composite Anode.

Dual-ion batteries (DIBs) are attracting attention due to their high operating voltage and promise in stationary energy storage applications. Among various anode materials, elements that alloy and dealloy with lithium are assumed to be prospective in bringing higher capacities and increasing the energy density of DIBs. In this work, antimony in the form of a composite with carbon (Sb-C) is evaluated as an anode material for DIB full cells for the first time. The behaviour of graphite||Sb-C cells is assessed in highly concentrated electrolytes in the absence and presence of an electrolyte additive (1 % vinylene carbonate) and in two cell voltage windows (2-4.5 V and 2-4.8 V). Sb-C full cells possess maximum estimated specific energies of 290 Wh/kg (based on electrode masses) and 154 Wh/kg (based on the combined mass of electrodes and active salt). The work expands the knowledge on the operation of DIBs with non-graphitic anodes.

Molecular-Cling-Effect of Fluoroethylene Carbonate Characterized via Ethoxy(pentafluoro)cyclotriphosphazene on SiOx/C Anode Materials - A New Perspective for Formerly Sub-Sufficient SEI Forming Additive Compounds.

Effective electrolyte compositions are of primary importance in raising the performance of lithium-ion batteries (LIBs). Recently, fluorinated cyclic phosphazenes in combination with fluoroethylene carbonate (FEC) have been introduced as promising electrolyte additives, which can decompose to form an effective dense, uniform, and thin protective layer on the surface of electrodes. Although the basic electrochemical aspects of cyclic fluorinated phosphazenes combined with FEC were introduced, it is still unclear how these two compounds interact constructively during operation. This study investigates the complementary effect of FEC and ethoxy(pentafluoro)cyclotriphosphazene (EtPFPN) in aprotic organic electrolyte in LiNi0.5 Co0.2 Mn0.3 O ∥ SiOx /C full cells. The formation mechanism of lithium ethyl methyl carbonate (LEMC)-EtPFPN interphasial intermediate products and the reaction mechanism of lithium alkoxide with EtPFPN are proposed and supported by Density Functional Theory calculations. A novel property of FEC is also discussed here, called molecular-cling-effect (MCE). To the best knowledge, the MCE has not been reported in the literature, although FEC belongs to one of the most investigated electrolyte additives. The beneficial MCE of FEC toward the sub-sufficient solid-electrolyte interphase forming additive compound EtPFPN is investigated via gas chromatography-mass spectrometry, gas chromatography high resolution-accurate mass spectrometry, in situ shell-isolated nanoparticle-enhanced Raman spectroscopy, and scanning electron microscopy.

Overcoming Diffusion Limitation of Faradaic Processes: Property-Performance Relationships of 2D Conductive Metal-Organic Framework Cu3 (HHTP)2 for Reversible Lithium-Ion Storage.

Faradaic reactions including charge transfer are often accompanied with diffusion limitation inside the bulk. Conductive two-dimensional frameworks (2D MOFs) with a fast ion transport can combine both-charge transfer and fast diffusion inside their porous structure. To study remaining diffusion limitations caused by particle morphology, different synthesis routes of Cu-2,3,6,7,10,11-hexahydroxytriphenylene (Cu3 (HHTP)2 ), a copper-based 2D MOF, are used to obtain flake- and rod-like MOF particles. Both morphologies are systematically characterized and evaluated for redox-active Li+ ion storage. The redox mechanism is investigated by means of X-ray absorption spectroscopy, FTIR spectroscopy and in situ XRD. Both types are compared regarding kinetic properties for Li+ ion storage via cyclic voltammetry and impedance spectroscopy. A significant influence of particle morphology for 2D MOFs on kinetic aspects of electrochemical Li+ ion storage can be observed. This study opens the path for optimization of redox active porous structures to overcome diffusion limitations of Faradaic processes.

Insights into Electrolytic Pre-Lithiation: A Thorough Analysis Using Silicon Thin Film Anodes.

Pre-lithiation via electrolysis, herein defined as electrolytic pre-lithiation, using cost-efficient electrolytes based on lithium chloride (LiCl), is successfully demonstrated as a proof-of-concept for enabling lithium-ion battery full-cells with high silicon content negative electrodes. An electrolyte for pre-lithiation based on γ-butyrolactone and LiCl is optimized using boron-containing additives (lithium bis(oxalato)borate, lithium difluoro(oxalate)borate) and CO2 with respect to the formation of a protective solid electrolyte interphase (SEI) on silicon thin films as model electrodes. Reversible lithiation in Si||Li metal cells is demonstrated with Coulombic efficiencies (CEff ) of 95-96% for optimized electrolytes comparable to 1 m LiPF6 /EC:EMC 3:7. Formation of an effective SEI is shown by cyclic voltammetry and X-ray photoelectron spectroscopy (XPS). electrolytic pre-lithiation experiments show that notable amounts of the gaseous product Cl2 dissolve in the electrolyte leading to a self-discharge Cl2 /Cl- shuttle mechanism between the electrodes lowering pre-lithiation efficiency and causing current collector corrosion. However, no significant degradation of the Si active material and the SEI due to contact with elemental chlorine is found by SEM, impedance, and XPS. In NCM111||Si full-cells, the capacity retention in the 100th cycle can be significantly increased from 54% to 78% by electrolytic pre-lithiation, compared to reference cells without pre-lithiation of Si.

Enabling Aqueous Processing of Ni-Rich Layered Oxide Cathode Materials by Addition of Lithium Sulfate.

Aqueous processing of Ni-rich layered oxide cathode materials is a promising approach to simultaneously decrease electrode manufacturing costs, while bringing environmental benefits by substituting the state-of-the-art (often toxic and costly) organic processing solvents. However, an aqueous environment remains challenging due to the high reactivity of Ni-rich layered oxides towards moisture, leading to lithium leaching and Al current collector corrosion because of the resulting high pH value of the aqueous electrode paste. Herein, a facile method was developed to enable aqueous processing of LiNi0.8 Co0.1 Mn0.1 O2 (NCM811) by the addition of lithium sulfate (Li2 SO4 ) during electrode paste dispersion. The aqueously processed electrodes retained 80 % of their initial capacity after 400 cycles in NCM811||graphite full cells, while electrodes processed without the addition of Li2 SO4 reached 80 % of their capacity after only 200 cycles. Furthermore, with regard to electrochemical performance, aqueously processed electrodes using carbon-coated Al current collector outperformed reference electrodes based on state-of-the-art production processes involving N-methyl-2-pyrrolidone as processing solvent and fluorinated binders. The positive impact on cycle life by the addition of Li2 SO4 stemmed from a formed sulfate coating as well as different surface species, protecting the NCM811 surface against degradation. Results reported herein open a new avenue for the processing of Ni-rich NCM electrodes using more sustainable aqueous routes.

Enabling Long-Cycling Life of Si-on-Graphite Composite Anodes via Fabrication of a Multifunctional Polymeric Artificial Solid-Electrolyte Interphase Protective Layer.

The energy density of lithium-ion batteries (LIBs) can be meaningfully increased by utilizing Si-on-graphite composites (Si@Gr) as anode materials, because of several advantages, including higher specific capacity and low cost. However, long cycling stability is a key challenge for commercializing these composites. In this study, to solve this issue, we have developed a multifunctional polymeric artificial solid-electrolyte interphase (A-SEI) protective layer on carbon-coated Si@Gr anode particles (making Si@Gr/C-SCS) to prolong the cycling stability in LIBs. The coating is made of sulfonated chitosan (SCS) that is crosslinked with glutaraldehyde promoting good ionic conduction together with sufficient mechanical strength of the A-SEI. The focused ion beam-scanning electron microscopy and high-resolution transmission electron microscopy images show that the SCS is uniformly coated on the composite particles with thickness in nanometer. The anodes are investigated in Li metal cells Si@Gr/C-SCS||Li metal) and lithium-ion full-cells (LiNi0.6Co0.2Mn0.2O2 (NCM-622)||Si@Gr/C-SCS) to understand the material/electrode intrinsic degradation as well as the impact of the polymer coating on active lithium losses because of the continuous SEI (re)formation. The anode composites exhibit a high capacity reaching over 600 mAh g-1, and even without electrolyte optimization, the Si@Gr/C-SCS illustrates a superior long cycle life performance of up to 1000 cycles (over 67% capacity retention). The excellent long-term cycling stability of the anodes was attributed to the SCS polymer coating acting as the A-SEI. The simple polymer coating process is highly interesting in guiding the preparation of long-cycle-life electrode materials of high-energy LIB cells.

Opportunities and Challenges of Li2 C4 O4 as Pre-Lithiation Additive for the Positive Electrode in NMC622||Silicon/Graphite Lithium Ion Cells.

Silicon (Si)-based negative electrodes have attracted much attention to increase the energy density of lithium ion batteries (LIBs) but suffer from severe volume changes, leading to continuous re-formation of the solid electrolyte interphase and consumption of active lithium. The pre-lithiation approach with the help of positive electrode additives has emerged as a highly appealing strategy to decrease the loss of active lithium in Si-based LIB full-cells and enable their practical implementation. Here, the use of lithium squarate (Li2 C4 O4 ) as low-cost and air-stable pre-lithiation additive for a LiNi0.6 Mn0.2 Co0.2 O2 (NMC622)-based positive electrode is investigated. The effect of additive oxidation on the electrode morphology and cell electrochemical properties is systematically evaluated. An increase in cycle life of NMC622||Si/graphite full-cells is reported, which grows linearly with the initial amount of Li2 C4 O4 , due to the extra Li+ ions provided by the additive in the first charge. Post mortem investigations of the cathode electrolyte interphase also reveal significant compositional changes and an increased occurrence of carbonates and oxidized carbon species. This study not only demonstrates the advantages of this pre-lithiation approach but also features potential limitations for its practical application arising from the emerging porosity and gas development during decomposition of the pre-lithiation additive.

Practical Implementation of Magnetite-Based Conversion-Type Negative Electrodes via Electrochemical Prelithiation.

We report the performance of a conversion-type magnetite-decorated partially reduced graphene oxide (Fe3O4@PrGO) negative electrode material in full-cell configuration with LiNi0.8Co0.15Al0.05O2 (NCA) positive electrodes. To enable practical implementation of the conversion-type negative electrodes in full cells, the beneficial impact of electrochemical prelithiation on mitigating active lithium losses and improving cycle life is shown here for the first time in the literature. The initial Coulombic efficiency (ICE) of the full cells is improved from 70.8 to 91.2% by prelithiation of the negative electrode to 35% of its specific delithiation capacity. The prelithiation is shown to improve the surface passivation of the Fe3O4@PrGO electrodes, leading to less electrolyte reduction on their surface which is prominent from the significantly lowered accumulated Coulombic inefficiency values, lower polarization growth, and doubled capacity retention by the 100th cycle. The reduced surface reactions of the negative electrode by prelithiation also aids in reducing the extent of aging of the NCA positive electrode. Overall, the prelithiation leads to a longer cycle life, where a retained capacity of 60.4% was achieved for the prelithiated cells by the end of long-term cycling, which is 3 times higher than the capacity retention of the non-prelithiated cells. Results reported herein indicate for the first time that the electrochemical prelithiation of the Fe3O4@PrGO electrode is a promising approach for making conversion negative electrode materials more applicable in lithium-ion batteries.

Advanced Dual-Ion Batteries with High-Capacity Negative Electrodes Incorporating Black Phosphorus.

Dual-graphite batteries (DGBs), being an all-graphite-electrode variation of dual-ion batteries (DIBs), have attracted great attention in recent years as a possible low-cost technology for stationary energy storage due to the utilization of inexpensive graphite as a positive electrode (cathode) material. However, DGBs suffer from a low specific energy limited by the capacity of both electrode materials. In this work, a composite of black phosphorus with carbon (BP-C) is introduced as negative electrode (anode) material for DIB full-cells for the first time. The electrochemical behavior of the graphite || BP-C DIB cells is then discussed in the context of DGBs and DIBs using alloying anodes. Mechanistic studies confirm the staging behavior for anion storage in the graphite positive electrode and the formation of lithiated phosphorus alloys in the negative electrode. BP-C containing full-cells demonstrate promising electrochemical performance with specific energies of up to 319 Wh kg-1 (related to masses of both electrode active materials) or 155 Wh kg-1 (related to masses of electrode active materials and active salt), and high Coulombic efficiency. This work provides highly relevant insights for the development of advanced high-energy and safe DIBs incorporating BP-C and other high-capacity alloying materials in their anodes.

Investigation of Lithium Polyacrylate Binders for Aqueous Processing of Ni-Rich Lithium Layered Oxide Cathodes for Lithium-Ion Batteries.

Ni-rich layered oxide cathodes are promising candidates to satisfy the increasing energy demand of lithium-ion batteries for automotive applications. Aqueous processing of such materials, although desirable to reduce costs and improve sustainability, remains challenging due to the Li+ /H+ exchange upon contact with water, resulting in a pH increase and corrosion of the aluminum current collector. Herein, an example was given for tuning the properties of aqueous LiNi0.83 Co0.12 Mn0.05 O2 electrode pastes using a lithium polyacrylate-based binder to find the "sweet spot" for processing parameters and electrochemical performance. Polyacrylic acid was partially neutralized to balance high initial capacity, good cycling stability, and the prevention of aluminum corrosion. Optimized LiOH/polyacrylic acid ratios in water were identified, showing comparable cycling performance to electrodes processed with polyvinylidene difluoride requiring toxic N-methyl-2-pyrrolidone as solvent. This work gives an exemplary study for tuning aqueous electrode pastes properties aiming towards a more environmentally friendly processing of Ni-rich cathodes.

Synergistic Effects of Surface Coating and Bulk Doping in Ni-Rich Lithium Nickel Cobalt Manganese Oxide Cathode Materials for High-Energy Lithium-Ion Batteries.

Invited for this month's cover is a combined work of the Helmholtz Institute Münster together with the MEET Battery Research Center and the Universities of Münster and Mainz. The cover shows multiple treatment choices for the modification of cathode active materials for lithium-ion batteries. Similar to a car wash program, the treatment will typically result in an improvement of the status quo. However, the best treatment procedure will only become clear if all modification pathways are explored. The Research Article itself is available at 10.1002/cssc.202102220.

Synergistic Effects of Surface Coating and Bulk Doping in Ni-Rich Lithium Nickel Cobalt Manganese Oxide Cathode Materials for High-Energy Lithium Ion Batteries.

Ni-rich layered oxide cathodes are promising candidates to satisfy the increasing energy demand of lithium-ion batteries for automotive applications. Thermal and cycling stability issues originating from increasing Ni contents are addressed by mitigation strategies such as elemental bulk substitution ("doping") and surface coating. Although both approaches separately benefit the cycling stability, there are only few reports investigating the combination of two of such approaches. Herein, the combination of Zr as common dopant in commercial materials with effective Li2 WO4 and WO3 coatings was investigated with special focus on the impact of different material processing conditions on structural parameters and electrochemical performance in nickel-cobalt-manganese (NCM) || graphite cells. Results indicated that the Zr4+ dopant diffusing to the surface during annealing improved the electrochemical performance compared to samples without additional coatings. This work emphasizes the importance to not only investigate the effect of individual dopants or coatings but also the influences between both.

Demonstrating Apparently Inconspicuous but Sensitive Impacts on the Rollover Failure of Lithium-Ion Batteries at a High Voltage.

Layered oxides, such as Li[Ni0.5Co0.2Mn0.3]O2 (NCM523), are promising cathode materials for operation at a high voltage, i.e., high-energy lithium-ion batteries. The instability-reasoned transition metal dissolution remains a major challenge, which initiates electrode cross-talk, alteration of the solid electrolyte interphase, and enhanced Li-metal dendrite formation at the graphite anode, consequently leading to rollover failure. In this work, relevant impacts on this failure mechanism are highlighted. For example, a conventional coating of NCM523 with aluminum oxide as a typical high-voltage modification improves kinetic aspects but can only postpone the rollover failure to later charge/discharge cycles. Interestingly, a similar effect on the rollover failure is observed merely after modification of the cell formation protocol, i.e., the first cycles. Further influences of specific test protocols are highlighted and show that the rollover failure even disappears at C-rates above 2C, which can be attributed to a more homogeneous distribution of Li-metal dendrite formation. It is worth noting that a variation of anode porosity can reveal similar effects, as, e.g., variations in anode processing also impact Li dendrite distribution and the appearance of rollover failure. Overall, the rollover failure is a valid but complex phenomenon, which sensitively depends on apparently inconspicuous parameters and should not be disregarded.

Solvent Co-Intercalation-Induced Activation and Capacity Fade Mechanism of Few-/Multi-Layered MXenes in Lithium Ion Batteries.

MXenes attract tremendous research efforts since their discovery in 2011 due to their unique physical and chemical properties, allowing for application in various fields. One of them is electrochemical energy storage due to their pseudocapacitive (=redox) behavior, high electronic conductivity, and charge storage versatility regarding the cationic species (e.g., Li+ ). MXenes typically display stable charge/discharge cycling behavior over hundreds of cycles in numerous electrolytes, however, a drastic loss of reversible capacity is detectable during the initial cycles. Furthermore, an electrochemical "activation" is also reported in the literature, especially for free-standing electrodes. Here, these electrochemical phenomena are investigated by electrochemical and analytical means to decipher the responsible mechanism by comparing few-layered and multi-layered Ti3 C2 Tx . A change in the pseudocapacitive behavior of MXenes during cycling can be explained by in situ X-ray diffraction studies, revealing solvent co-intercalation in the first cycle for the morphologically different MXenes. This co-intercalation is responsible for the capacity decay detected in the first cycles and is also responsible for the ongoing "activation" occurring in later cycles.

Opportunities and Limitations of Ionic Liquid- and Organic Carbonate Solvent-Based Electrolytes for Mg-Ion-Based Dual-Ion Batteries.

Dual-ion batteries (DIBs) offer a great alternative to state-of-the-art lithium-ion batteries, based on their high promises due to the absence of transition metals and the use of low-cost materials, which could make them economically favorable targeting stationary energy storage applications. In addition, they are not limited by certain metal cations, and DIBs with a broad variety of utilized ions could be demonstrated over the last years. Herein, a systematic study of different electrolyte approaches for Mg-ion-based DIBs was conducted. A side-by-side comparison of Li- and Mg-ion-based electrolytes using activated carbon as negative electrode revealed the opportunities but also limitations of Mg-ion-based DIBs. Ethylene sulfite was successfully introduced as electrolyte additive and increased the specific discharge capacity significantly up to 93±2 mAh g-1 with coulombic efficiencies over 99 % and an excellent capacity retention of 88 % after 400 cycles. In addition, and for the first time, highly concentrated carbonate-based electrolytes were employed for Mg-ion-based DIBs, showing adequate discharge capacities and high coulombic efficiencies.

Scalable Synthesis of MAX Phase Precursors toward Titanium-Based MXenes for Lithium-Ion Batteries.

MXenes have emerged as one of the most interesting material classes, owing to their outstanding physical and chemical properties enabling the application in vastly different fields such as electrochemical energy storage (EES). MXenes are commonly synthesized by the use of their parent phase, i.e., MAX phases, where "M" corresponds to a transition metal, "A" to a group IV element, and "X" to carbon and/or nitrogen. As MXenes display characteristic pseudocapacitive behaviors in EES technologies, their use as a high-power material can be useful for many battery-like applications. Here, a comprehensive study on the synthesis and characterization of morphologically different titanium-based MXenes, i.e., Ti3C2 and Ti2C, and their use for lithium-ion batteries is presented. First, the successful synthesis of large batches (≈1 kg) of the MAX phases Ti3AlC2 and Ti2AlC is shown, and the underlying materials are characterized mainly by focusing on their structural properties and phase purity. Second, multi- and few-layered MXenes are successfully synthesized and characterized, especially toward their ever-present surface groups, influencing the electrochemical behavior to a large extent. Especially multi- and few-layered Ti3C2 are achieved, exhibiting almost no oxidation and similar content of surface groups. These attributes enable the precise comparison of the electrochemical behavior between morphologically different MXenes. Since the preparation method for few-layered MXenes is adapted to process both active materials in a "classical" electrode paste processing method, a better comparison between both materials is possible by avoiding macroscopic differences. Therefore, in a final step, the aforementioned electrochemical performance is evaluated to decipher the impact of the morphology difference of the titanium-based MXenes. Most importantly, the delamination leads to an increased non-diffusion-limited contribution to the overall pseudocapacity by enhancing the electrolyte access to the redox-active sites.

Solvent Co-intercalation into Few-layered Ti3C2Tx MXenes in Lithium Ion Batteries Induced by Acidic or Basic Post-treatment.

MXenes, as an emerging class of 2D materials, display distinctive physical and chemical properties, which are highly suitable for high-power battery applications, such as lithium ion batteries (LIBs). Ti3C2Tx (Tx = O, OH, F, Cl) is one of the most investigated MXenes to this day; however, most scientific research studies only focus on the design of multilayered or monolayer MXenes. Here, we present a comprehensive study on the synthesis of few-layered Ti3C2Tx materials and their use in LIB cells, in particular for high-rate applications. The synthesized Ti3C2Tx MXenes are characterized via complementary XRD, Raman spectroscopy, XPS, EDX, SEM, TGA, and nitrogen adsorption techniques to clarify the structural and chemical changes, especially regarding the surface groups and intercalated cations/water molecules. The structural changes are correlated with respect to the acidic and basic post-treatment of Ti3C2Tx. Furthermore, the detected alterations are put into an electrochemical perspective via galvanostatic and potentiostatic investigations to study the pseudocapacitive behavior of few-layered Ti3C2Tx, exhibiting a stable capacity of 155 mAh g-1 for 1000 cycles at 5 A g-1. The acidic treatment of Ti3C2Tx synthesized via the in situ formation of HF through LiF/HCl is able to increase the initial capacity in comparison to the pristine or basic treatment. To gain further insights into the structural changes occurring during (de)lithiation, in situ XRD is applied for LIB cells in a voltage range from 0.01 to 3 V to give fundamental mechanistic insights into the structural changes occurring during the first cycles. Thereby, the increased initial capacity observed for acidic-treated MXenes can be explained by the reduced co-intercalation of solvent molecules.