A Portable Readout System for Biomarker Detection with Aptamer-Modified CMOS ISFET Array.

Biosensors based on ion-sensitive field effect transistors (ISFETs) combined with aptamers offer a promising and convenient solution for point-of-care testing applications due to the ability for fast and label-free detection of a wide range of biomarkers. Mobile and easy-to-use readout devices for the ISFET aptasensors would contribute to further development of the field. In this paper, the development of a portable PC-controlled device for detecting aptamer-target interactions using ISFETs is described. The device assembly allows selective modification of individual ISFETs with different oligonucleotides. Ta2O5-gated ISFET structures were optimized to minimize trapped charge and capacitive attenuation. Integrated CMOS readout circuits with linear transfer function were used to minimize the distortion of the original ISFET signal. An external analog signal digitizer with constant voltage and superimposed high-frequency sine wave reference voltage capabilities was designed to increase sensitivity when reading ISFET signals. The device performance was demonstrated with the aptamer-driven detection of troponin I in both reference voltage setting modes. The sine wave reference voltage measurement method reduced the level of drift over time and enabled a lowering of the minimum detectable analyte concentration. In this mode (constant voltage 2.4 V and 10 kHz 0.1Vp-p), the device allowed the detection of troponin I with a limit of detection of 3.27 ng/mL. Discrimination of acute myocardial infarction was demonstrated with the developed device. The ISFET device provides a platform for the multiplexed detection of different biomarkers in point-of-care testing.

Off-Stoichiometry Thiol-Ene Polymers: Inclusion of Anchor Groups Using Allylsilanes.

The use of polymers in silicon chips is of great importance for the development of microelectronic and biomedical industries. In this study, new silane-containing polymers, called OSTE-AS polymers, were developed based on off-stoichiometry thiol-ene polymers. These polymers can bond to silicon wafers without pretreatment of the surface by an adhesive. Silane groups were included in the polymer using allylsilanes, with the thiol monomer as the target of modification. The polymer composition was optimized to provide the maximum hardness, the maximum tensile strength, and good bonding with the silicon wafers. The Young's modulus, wettability, dielectric constant, optical transparency, TGA and DSC curves, and the chemical resistance of the optimized OSTE-AS polymer were studied. Thin OSTE-AS polymer layers were obtained on silicon wafers via centrifugation. The possibility of creating microfluidic systems based on OSTE-AS polymers and silicon wafers was demonstrated.

Off-Stoichiometry Thiol-Enes Polymers Containing Silane Groups for Advanced Packaging Technologies.

New modified off-stoichiometry thiol-enes polymers, called OSTE-MS polymers, were developed by introducing mercaptosilane into the polymer mixture. This modification made it possible to introduce silane groups into the polymer frame, due to which the polymer gained the ability to bond with silicon wafers without modification of the wafer surface by any adhesive. The optimal composition for creating 3D polymer structures on a chip was selected, which consists of a volume ratio of 6:6:1 of allyl monomer, mercapto monomer, and mercaptosilane, respectively. The hardness, shift force, tensile strength, Young's modulus, optical transparency, glass transition temperature, thermal stability, and chemical resistance of the OSTE-MS polymer, and the viscosity for the prepolymer mixture were studied. On the basis of the OSTE-MS polymer, 3D polymer structures of the well type and microfluidic system on the silicon chips were obtained.

A route to virtually unlimited functionalization of water-soluble p-sulfonatocalix[4]arenes.

The functionality of p-sulfonatocalix[4]arenes can be easily extended using the propargylation/CuAAC reaction sequence, which allows the introduction of up to four substituted triazole units to the narrow rims of the macrocycles while maintaining their cone shapes and water solubility and, thus, biomedical applicability.

Integration of a field effect transistor-based aptasensor under a hydrophobic membrane for bioelectronic nose applications.

A new bioelectronic nose based on a field effect transistor coupled with an aptamer as the sensing element was developed. The gas-to-liquid extraction interface required for appropriate aptamer function was integrated into standard CMOS technology. It was developed with the use of a sacrificial aluminium etching technique combined with surface modifications by silanes for wettability control. As a proof of concept, aptamer Van74 for vanillin was immobilized on the sensitive surface of the ISFET. The developed microsystem can selectively detect vanillin vapor in a concentration range from 2.7 ppt to 0.3 ppm, with a detection limit of 2.7 ppt. The sensor was able to detect vanillin in a gas sample obtained from roasted coffee beans. This outcome provides a foundation for developing a new generation of bioelectronic noses for the detection and discrimination of volatile compounds.

Field-effect transition sensor for KI detection based on self-assembled calixtube monolayers.

A series of novel calixarene-based tubes comprising different numbers of silatrane anchoring groups was synthesized. For the first time, a self-assembled monolayer (SAM) derived from calixtubes was formed on a SiO2 surface. The formation of the SAM was confirmed by X-ray photoelectron spectroscopy, scanning electron microscopy-energy dispersive X-ray analysis, and contact angle measurements. Modification of the sensitive surface of a conventional ion-selective field effect transistor (ISFET) with the afforded SAM resulted in the production of a KI-sensitive sensor. This sensor selectively determined KI compare to different alkali metal iodides: NaI, RbI, CsI; also investigation of different potassium salts (acetate, iodide, nitrate, chloride, dihydrophosphate, perchlorate) showed the highest response to KI. This sensor was successfully employed to determine the presence of KI in artificial saliva with a limit of detection of ~3 × 10-8 М. In addition, it was found that the detection limit of the sensor could be increased by combining the sensor with a microfluidic system. Due to the obtained sensor sensitivity and its ability to detect KI in artificial saliva, we could conclude that this sensor shows great potential for application in the determination of KI in different media, such as the human body and in biological liquids, such as saliva or urine.

Calix[4]tubes: an approach to functionalization.

Adamantylcalix[4]arenes decorated with ester groups and calix[4]arene tetratosylates were used to prepare a series of calix[4]tubes bearing 3-methoxycarbonyl- and 3-methoxycarbonylmethyl-1-adamantyl units (up to eight) in good yield. These compounds were subjected to further chemical transformations giving a wide set of novel ester-, acid-, hydroxy-, amine-, and urea-functionalized calix[4]tubes. Introduction of urea groups into the calixtube core led not only to anion-targeted receptors, but also provided heteroditopic behavior of the hosts, which enriches the well-established potassium-uptake ability of calix[4]tubes.