Hyperbranched TiO2-CdS nano-heterostructures for highly efficient photoelectrochemical photoanodes.

Quasi-1D-hyperbranched TiO2 nanostructures are grown via pulsed laser deposition and sensitized with thin layers of CdS to act as a highly efficient photoelectrochemical photoanode. The device properties are systematically investigated by optimizing the height of TiO2 scaffold structure and thickness of the CdS sensitizing layer, achieving photocurrent values up to 6.6 mA cm-2 and reaching saturation with applied biases as low as 0.35 VRHE. The high internal conversion efficiency of these devices is to be found in the efficient charge generation and injection of the thin CdS photoactive film and in the enhanced charge transport properties of the hyperbranched TiO2 scaffold. Hence, the proposed device represents a promising architecture for heterostructures capable of achieving high solar-to-hydrogen efficiency.

Hematite photoanodes modified with an Fe(III) water oxidation catalyst.

Hematite photoelectrodes prepared via a hydrothermal route are functionalized with a water oxidation catalyst consisting of amorphous Fe(III) oxide, obtained by successive ionic layer adsorption and reaction. The performances of the catalyst-modified photoanodes are considerably higher than those of the parent electrodes, resulting in a nearly doubled photoanodic current in all the basic aqueous electrolytes explored in this study. The combination of electrochemical impedance spectroscopy and laser flash photolysis indicates that the presence of the catalyst results in enhanced hole trapping in surface reactive states exposed to the electrolyte, allowing for a more successful competition between charge transfer and recombination.

Efficient solar water oxidation using photovoltaic devices functionalized with earth-abundant oxygen evolving catalysts.

Indium tin oxide (ITO) surfaces of triple junction photovoltaic cells were functionalized with oxygen evolving catalysts (OECs) based on amorphous hydrous earth-abundant metal oxides (metal = Fe, Ni, Co), obtained by straightforward Successive Ionic Layer Adsorption and Reaction (SILAR) in an aqueous environment. Functionalization with Fe(iii) oxides gave the best results, leading to photoanodes capable of efficiently splitting water, with photocurrent densities up to 6 ± 1 mA cm(-2) at 0 V vs. the reversible hydrogen electrode (RHE) under AM 1.5 G simulated sunlight illumination. The resulting Solar To Hydrogen (STH) conversion efficiencies, measured in two electrodes configuration, were in the range 3.7-5%, depending on the counter electrode that was employed. Investigations on the stability showed that these photoanodes were able to sustain 120 minutes of continuous illumination with a < 10% photocurrent loss at 0 V vs. RHE. Pristine photoanodic response of the cells could be fully restored by an additional SILAR cycle, evidencing that the observed loss is due to the detachment of the more weakly surface bound catalyst.

Nanostructured photoelectrodes based on WO3: applications to photooxidation of aqueous electrolytes.

Some recent studies mainly addressing the preparation and the modification of nanostructured thin films based on WO(3) and their application to photoelectrolysis of aqueous electrolytes are reviewed with the aim of rationalizing the main factors at the basis of an efficient photoanodic response. WO(3) represents one of the few materials which can achieve efficient water photo-oxidation under visible illumination, stably operating under strongly oxidizing conditions; thus the discussion of the structure-related photoelectrochemical properties of WO(3) thin films and their optimization for achieving almost quantitative photon to electron conversion constitutes the core of this contribution.

Photoanodes based on nanostructured WO3 for water splitting.

Anodically grown WO(3) photoelectrodes prepared in an N-methylformamide (NMF) electrolyte have been investigated with the aim of exploring the effects induced by anodization time and water concentration in the electrochemical bath on the properties of the resulting photoanodes. An n-type WO(3) semiconductor is one of the most promising photoanodes for hydrogen production from water splitting and the electrochemical anodization of tungsten allows very good photoelectrodes, which are characterized by a low charge-transfer resistance and an increased spectral response in the visible region, to be obtained. These photoanodes were investigated by a combination of steady state and transient photoelectrochemical techniques and a correlation between photocurrent produced, morphology, and charge transport has been evaluated.