Gluteal and thigh compartment syndrome after open abdominal aortic aneurysm repair.

Although compartment syndrome (CS) can occur in any myofascial compartment, the thigh and buttock are among the least common. CS is characterized by an increase in pressure of a myofascial compartment that results in a reduction of capillary blood flow and myonecrosis. Although >75% of cases of CS occur after long bone fractures, acute CS can also occur from nontraumatic and vascular etiologies. We report a case of gluteal and thigh CS resulting from ischemia-reperfusion injury after abdominal aortic aneurysm repair and left common iliac artery bypass.

A self calibrating, magnetic sensor approach accurately positions an aortic damage control stent in a porcine model.

Objectives: Non-compressible torso hemorrhage remains a high mortality injury, with difficulty mobilizing resources before exsanguination. Previous studies reported on a retrievable stent graft for damage control and morphometric algorithms for rapid placement, yet fluoroscopy is impractical for the austere environment. We hypothesized that magnetic sensors could be used to position stents relative to an external magnet placed on an anatomic landmark, whereas an electromagnet would allow self-calibration to account for environmental noise. Methods: A magnetic sensor alone (MSA) and with integrated stent (MSIS) were examined in a porcine model under anesthesia. A target electromagnet was placed on the xiphoid process (position 0 cm). Sensors were placed in the aorta and measurements obtained at positions 0 cm, +4 cm, and +12 cm from the magnet and compared with fluoroscopy. Sensors were examined under conditions of tachycardia/hypertension, hypotension, vibration, and metal shrapnel to simulate environmental factors that might impact accuracy. General linear models compared mean differences between fluoroscopy and sensor readings. Results: Both sensors were compatible with a 10 French catheter system and provided real-time assessment of the distance between the sensor and magnetic target in centimeters. Mean differences between fluoroscopy and both magnetic sensor readings demonstrated accuracy within ±0.5 cm for all but one condition at 0 cm and +4 cm, whereas accuracy decreased at +12 cm from the target. Using the control as a reference, there was no significant difference in mean differences between fluoroscopy and both MSA or MSIS readings at 0 cm and +4 cm for all conditions. The system retained effectiveness if the target was overshot. Conclusion: Magnetic sensors achieved the highest accuracy as sensors approached the target. Oscillation of the electromagnet on and off effectively accounts for environmental noise.This approach is promising for rapid and accurate placement of damage control retrievable stent grafts when fluoroscopy is impractical. Level of evidence: Not applicable.

A System to Track Stent Location in the Human Body by Fusing Magnetometer and Accelerometer Measurements.

This paper will introduce a simple locating system to track a stent when it is deployed into a human artery. The stent is proposed to achieve hemostasis for bleeding soldiers on the battlefield, where common surgical imaging equipment such as fluoroscopy systems are not available. In the application of interest, the stent must be guided to the right location to avoid serious complications. The most important features are its relative accuracy and the ease by which it may be quickly set up and used in a trauma situation. The locating approach in this paper utilizes a magnet outside the human body as the reference and a magnetometer that will be deployed inside the artery with the stent. The sensor can detect its location in a coordinate system centered with the reference magnet. In practice, the main challenge is that the locating accuracy will be deteriorated by external magnetic interference, rotation of the sensor, and random noise. These causes of error are addressed in the paper to improve the locating accuracy and repeatability under various conditions. Finally, the system's locating performance will be validated in benchtop experiments, where the effects of the disturbance-eliminating procedures will be addressed.

A dumbbell rescue stent graft facilitates clamp-free repair of aortic injury in a porcine model.

Objective: Noncompressible torso hemorrhage is a high-mortality injury. We previously reported improved outcomes with a retrievable rescue stent graft to temporize aortic hemorrhage in a porcine model while maintaining distal perfusion. A limitation was that the original cylindrical stent graft design prohibited simultaneous vascular repair, given the concern for suture ensnarement of the temporary stent. We hypothesized that a modified, dumbbell-shaped design would preserve distal perfusion and also offer a bloodless plane in the midsection, facilitating repair with the stent graft in place and improve the postrepair hemodynamics. Methods: In an Institutional Animal Care and Use Committee-approved terminal porcine model, a custom retrievable dumbbell-shaped rescue stent graft (dRS) was fashioned from laser-cut nitinol and polytetrafluoroethylene covering and compared with aortic cross-clamping. Under anesthesia, the descending thoracic aorta was injured and then repaired with cross-clamping (n = 6) or dRS (n = 6). Angiography was performed in both groups. Operations were divided into phases: (1) baseline, (2) thoracic injury with either cross-clamp or dRS deployed, and (3) recovery, after which the clamp or dRS were removed. Target blood loss was 22% to simulate class II or III hemorrhagic shock. Shed blood was recovered with a Cell Saver and reinfused for resuscitation. Renal artery flow rates were recorded at baseline and during the repair phase and reported as a percentage of cardiac output. Phenylephrine pressor requirements were recorded. Results: In contrast with cross-clamped animals, dRS animals demonstrated both operative hemostasis and preserved flow beyond the dRS angiographically. Recovery phase mean arterial pressure, cardiac output, and right ventricular end-diastolic volume were significantly higher in dRS animals (P = .033, P = .015, and P = .012, respectively). Whereas distal femoral blood pressures were absent during cross-clamping, among the dRS animals, the carotid and femoral MAPs were not significantly different during the injury phase (P = .504). Cross-clamped animals demonstrated nearly absent renal artery flow, in contrast with dRS animals, which exhibited preserved perfusion (P<.0001). Femoral oxygen levels (partial pressure of oxygen) among a subset of animals further confirmed greater distal oxygenation during dRS deployment compared with cross-clamping (P = .006). After aortic repair and clamp or stent removal, cross-clamped animals demonstrated more significant hypotension, as demonstrated by increased pressor requirements over stented animals (P = .035). Conclusions: Compared with aortic cross-clamping, the dRS model demonstrated superior distal perfusion, while also facilitating simultaneous hemorrhage control and aortic repair. This study demonstrates a promising alternative to aortic cross-clamping to decrease distal ischemia and avoid the unfavorable hemodynamics that accompany clamp reperfusion. Future studies will assess differences in ischemic injury and physiological outcomes. Clinical Relevance: Noncompressible aortic hemorrhage remains a high-mortality injury, and current damage control options are limited by ischemic complications. We have previously reported a retrievable stent graft to allow rapid hemorrhage control, preserved distal perfusion, and removal at the primary repair. The prior cylindrical stent graft was limited by the inability to suture the aorta over the stent graft owing to risk of ensnarement. This large animal study explored a dumbbell retrievable stent with a bloodless plane to allow suture placement with the stent in place. This approach improved distal perfusion and hemodynamics over clamp repair and heralds the potential for aortic repair while avoiding complications.

Extra-Anatomic Bypass and Excision is Superior to Graft Salvage Attempts with Antibiotic Beads to Treat Vascular Graft Infections in the Groin.

BACKGROUND: This study aimed to determine if conventional extra-anatomic bypass and graft removal versus aggressive attempts at graft preservation have better survival and limb salvage in patients with localized groin wound infections of vascular grafts. METHODS: We conducted a retrospective review of 53 consecutive patients with vascular graft infections presenting in the groin. Treatment groups consisted of group 1 (extra-anatomic bypass and graft excision, n = 22) and group 2 (initial graft preservation attempts with utilization of antibiotic beads, n = 31). In group 2, patients underwent serial debridement and placement of antibiotic beads until culture-negative wounds were achieved. Significantly more patients underwent muscle flap coverage in group 2 (27/31) compared with group 1 (7/22; P < 0.001). Data collected included demographics, comorbidities, intraoperative details, and outcomes, including patency, limb salvage, mortality, and number of procedures. Continuous variables were examined with Student's t-test, and dichotomous variables were examined with chi-squared test. Linear and logistic regressions were used to analyze factors associated with outcomes, in addition to Kaplan-Meier analysis with log rank for actuarial analysis. RESULTS: Both groups were similar with respect to demographics. The overall Kaplan-Meier 1- and 3-year survival rates were 66.2% and 34.1%, with no statistically significant difference between groups. The Kaplan-Meier 1- and 3-year limb salvage rates were 68.8% and 36.6% for group 1 vs. 58.5% and 38.7% for group 2 (P = not significant [NS]). The 1- and 3-year primary patency rates were 71% and 71% in traditional group 1 vs. 72% and 56% in group 2 (P = NS). One-year and 3-year secondary patency rates in traditional group 1 were 83% and 71% vs. 85% and 61% in group 2 (P = NS). Patients in group 1 underwent fewer total procedures when compared with group 2 (2.3 ± 0.2 vs. 5.1 ± 0.7, P = 0.03). The late reinfection rate was significantly less in group 1 (4.5%) compared with group 2 (26%; P = 0.04). Freedom from reinfection at 1 and 3 years were 94% and 94% in traditional group 1 vs. 74% and 62% in group 2 (P = 0.03). Multivariable analysis showed a higher incidence of amputation in patients who suffered reinfection (n = 13, P = 0.049). There was a higher mortality in patients with septic shock (n = 10, P = 0.007) and reinfection (n = 13, P = 0.036). Reinfection was associated with the highest mortality (P = 0.03). CONCLUSIONS: Conventional graft excision with extra-anatomic bypass resulted in similar mortality when compared with aggressive attempts at graft preservation and trended toward improved limb salvage and patency. However, attempts at graft preservation with antibiotic beads resulted in a significantly higher reinfection rate and greater number of procedures, and therefore, this approach should be used very selectively.

A prebifurcated axillobifemoral polytetrafluoroethylene graft simplifies carotid to carotid to subclavian bypass.

The use of thoracic endovascular aortic repair for thoracic aortic disease will necessitate cervical debranching in cases involving the proximal arch. We have presented the case of a 57-year-old athletic woman who had developed a type A dissection that extended to the bilateral iliac arteries. After hemiarch repair, she underwent staged cervical debranching with carotid-carotid-subclavian bypass using a prebifurcated axillobifemoral graft and subsequent thoracic endovascular aortic repair. We have detailed her successful clinical course and described the benefits of using a prebifurcated graft for cervical debranching in hybrid repairs of aortic arch pathology.

The anchor point algorithm: A morphometric analysis of anatomic landmarks to guide placement of temporary aortic Rescue stent grafts for noncompressible torso hemorrhage.

BACKGROUND: Noncompressible hemorrhage remains a high-mortality injury, which requires rapid damage control within minutes to avoid exsanguination. Retrievable stent grafts offer perfusion preserving hemorrhage damage control, and yet algorithms for device selection and positioning are lacking for an anatomically diverse human population. We hypothesized that easily acquired external measurements could be used to rapidly triage patients to receive one of several presized stents and that these metrics may further predict a single target on the aorta by which to optimize both mesenteric perfusion and aortic hemorrhage control. METHODS: Metrics were acquired from computed tomography imaging of 203 male and female patients aged 18 to 50 years. Algorithms for metric based triage and stent sizing were examined against the cohort for effectiveness. Linear regression was used to predict a single target on the aorta for alignment of a multitiered stent. Next, the relationship of the anchor point to the palpable xiphoid was determined. RESULTS: Clavicle to pubis measurements correlated with aortic length and was used to triage patients to one of three stent grafts. Stents for each triage group were sized to achieve >75% coverage of aortic Zones 1 and 3 in most patients while preserving carotid and visceral perfusion. A metric/sex-based equation that predicts the location of the superior mesenteric artery relative to the palpable xiphoid was derived. By alignment of a single point on the stent with this target, known as the anchor point, the remainder of the stent can be rapidly deployed while minimizing coverage of critical branches. When applied back to the cohort, only 10.4% had potential serious branch coverage events predicted. CONCLUSION: Simple anatomic metrics offer rapid triage in this study population to one of three presized stent grafts and predict the location of key vascular branches. Confirmatory human trials will be essential to demonstrate safety and effectiveness of this approach. LEVEL OF EVIDENCE: Prognostic/Epidemiological; Level IV.

Understanding the Mechanism of Drug Transfer and Retention of Drug-Coated Balloons.

OBJECTIVE: The purpose of this study was to determine the impact of varying inflation parameters on paclitaxel delivery and retention using a commercially available DCB. BACKGROUND: Drug-coated balloons (DCB) have become the standard treatment for peripheral artery disease. Clinical data suggest that varying DCB delivery parameters directly impact patient outcome. Differences in delivery parameters can potentially alter the retention of the drug coating on DCBs. METHODS: Harvested porcine carotid arteries were utilized in an ex vivo pulsatile flow bioreactor system. The DCBs were then deployed at a DCB-to-artery ratio of 1:1 or 1.25:1, an inflation time of 30 seconds or 1 minute and transit time of 30 seconds or 3 minutes. The amount of drug retention in arterial tissue was evaluated by pharmacokinetic analysis at 1 hour and 1 day post DCB deployment. RESULTS: Arterial paclitaxel levels were found to be less at an inflation ratio of 1:1 with 3-minute transit time as compared to 30 seconds of transit time at 1 hour (12.3 ± 1.6 ng/mg vs. 391 ± 139 ng/mg, P = .036). At 1-day, DCBs deployed at a ratio of 1:1 resulted in less drug retention as compared to 1.25:1 (61.3 ± 23.1 ng/mg vs. 404 ± 195 ng/mg, P = .013). CONCLUSION: Arterial paclitaxel retention is reduced with extended transit times and sub-optimal expansion of the balloon. Optimization of delivery parameters can serve as an effective strategy to enhance clinical DCB outcomes.

In vitro and In vivo assessment of a novel organ perfusion stent for successful flow separation in donation after cardiac death.

Shortage of healthy donors' organs has appeared as one of the main challenges for organ transplantation. This study focuses on the novel endovascular device development to increase the number of available organs from cardiac death donors. The primary objective of this study is the design validation of a newly developed stent graft for the abdominal organ perfusion with cardiac blood flow isolation. In this paper, the effectiveness of the device design has been validated via the assessment of the device performance both in vitro and in vivo. The radial force of stent structure was first numerically analyzed using finite element method, then was quantified experimentally. The blood perfusion parameters were investigated to demonstrate their effect on the blood delivered to the abdominal organs, maintaining the organs healthy for donation. In vitro flow leakage was measured using a 3-D printing-based silicone aortic model to evaluate the isolation between cardiac flow and perfusion flow with minimum values. Following the design validation process, a functional prototype stent graft has been successfully fabricated using optimized laser welding conditions and subsequent joining processes. In vivo porcine study results have demonstrated smooth delivery and successful placement of the device showing complete cardiac flow separation isolating abdominal regions only with the oxygenated blood flow.

A retrievable, dual-chamber stent protects against warm ischemia of donor organs in a model of donation after circulatory death.

BACKGROUND: Ischemic injury during the agonal period of donation after circulatory death donors remains a significant barrier to increasing abdominal transplants. A major obstacle has been the inability to improve visceral perfusion, while at the same time respecting the ethics of the organ donor. A retrievable dual-chamber stentgraft could potentially isolate the organ perfusion from systemic hypotension and hypoxia, without increasing cardiac work or committing the donor. METHODS: Retrievable dumbbell-shaped stents were laser welded from nitinol wire and covered with polytetrafluoroethylene. Yorkshire pigs were assigned to either agonal control or dumbbell-shaped dual-chamber stentgraft. A central lumen maintained aortic flow, while an outer visceral chamber was perfused with oxygenated blood. A 1-hour agonal phase of hypoxia and hypotension was simulated. Stents were removed by simple sheath advancement. Cardiac monitoring, labs, and visceral flow were recorded followed by recovery of the animal to a goal of 48 hours. RESULTS: Cardiac stress did not increase during stent deployment. Visceral pO2 and flow were dramatically improved in stented animal relative to control animals. Five of 7 control animals were killed after renal failure complications, whereas all stent animals survived. Histology confirmed increased ischemic changes among control kidneys compared to stented animals. CONCLUSION: A dual-chamber stent improved outcomes after a simulated agonal phase. The stent did not increase cardiac work, thus respecting a key ethical consideration. The ability of a dual-chamber stent to prevent ischemia during organ recovery may become a powerful tool to address the critical donor organ shortage.

Assessment of mechanical and biocompatible performance of ultra-large nitinol endovascular devices fabricated via a low-energy laser joining process.

Nitinol is an excellent candidate material for developing various self-expanding endovascular devices due to its unique properties such as superelasticity, biocompatibility and shape memory effect. A low-energy laser joining technique suggests a high potential to create various large diameter Nitinol endovascular devices that contain complex geometries. The primary purpose of the study is to investigate the effects of laser joining process parameters with regard to the mechanical and biocompatible performance of Nitinol stents. Both the chemical composition and the microstructure of the laser-welded joints were evaluated using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). In vitro study results on cytotoxicity demonstrated that the joining condition of 8 Hz frequency and 1 kW laser power showed the highest degree of endothelial cell viability after thermal annealing in 500°C for 30 min. Also, in vitro study results showed the highest oxygen content at 0.9 kW laser power, 8 Hz frequency, and 0.3 mm spot size after the thermal annealing. Mechanical performance test results showed that the optimal condition for the highest disconnecting force was found at 1 Hz frequency and 1 kW power with 0.6 mm spot size. Two new endovascular devices have been fabricated using the optimized laser joining parameters, which have demonstrated successful device delivery and retrieval, as well as acute biocompatibility.

A three-tier Rescue stent improves outcomes over balloon occlusion in a porcine model of noncompressible hemorrhage.

BACKGROUND: Noncompressible hemorrhage remains a high-mortality injury, and aortic balloon occlusion poses limitations in terms of distal ischemic injury. Our hypothesis was that a retrievable Rescue stent would confer improved outcome over aortic balloon occlusion. METHODS: A three-tier, retrievable stent graft was laser welded from nitinol and polytetrafluoroethylene to provide rapid thoracic and abdominal coverage with an interval bare metal segment to preserve visceral flow. Anesthetized swine had injury of the thoracic or abdominal aorta followed by balloon occlusion or a Rescue stent. A 1-hour long damage-control phase with blood repletion was used to simulate the prolonged interval between injury and repair, especially in the battlefield setting. Following the damage-control phase, the balloon or stent were retrieved followed by vascular repair and recovery to 48 hours. Animals were compared in terms of hemodynamics, blood loss, neurophysiologic spinal cord ischemia, ischemic organ injury, and survival. RESULTS: Despite antegrade hemorrhage control, balloon occlusion averaged 3.5 L of retrograde hemorrhage, loss of visceral perfusion, and permanent spinal cord ischemia by neurophysiology in six of seven animals. After permanent repair, all balloon occlusion animals died with only a single short term (5 hours) survivor. Conversely, Rescue stent animals revealed rapid hemorrhage control (in under 2 minutes) whether the injury was thoracic or abdominal with improved hemodynamics, preserved visceral flow, reduced spinal cord ischemia, negligible histologic organ injury and survival to end of study in all abdominal injured animals (n = 6) and four of six thoracic injured animals, with two deaths related to arrhythmia. CONCLUSION: Compared with aortic balloon occlusion, a Rescue stent offers superior hemorrhage control and survival by virtue of reduced ischemic injury and direct control of the hemorrhagic injury. The Rescue stent may become a useful tool for damage control, especially on the battlefield where definitive repair presents logistical challenges.

Comprehensive assessment of mechanical behavior of an extremely long stent graft to control hemorrhage in torso.

Traumatic vascular injuries, resulting from either civilian accidents or wounded soldiers, require new endovascular devices (i.e., stent graft) to rapidly control the excessive internal hemorrhage in torso region. Current stent designs are limited by their permanent nature, which is note well suited for emergent placement. A retrievable stent graft could regulate the internal bleeding temporarily, as fast as possible with the most feasible performance, until the patients arrive the hospital to receive the proper treatment. The novel endovascular device of this study is designed according to the anatomy of a porcine model with plans to transition to a human model in the future. The stent graft is manufactured using a substantially long nitinol backbone and covered selectively based on anatomic measurements, with highly stretchable expanded-polytetrafluoroethylene (ePTFE). In this study, our group comprehensively explored designing and manufacturing methods, and their impact on the stent graft performance. Geometric parameters and heat treatment conditions were investigated to show their effect on the radial force of the metallic backbone. As a retrievable device, the resistance force for retrieval as well as deployment were measured, and analyzed to be manipulated through ePTFE covering configurations. In vitro measurements for bleeding were measured using swine aorta to show the functionality of the stent graft under the simulated pulsatile flow circulation. Finally, the stent graft showed substantial effectiveness for hemorrhage control in vivo, using swine model. The new design and fabrication methods enable rapid hemorrhage control that can be removed at the time of a dedicated surgical repair.

A novel customizable stent graft that contains a stretchable ePTFE with a laser-welded nitinol stent.

Customizable medical devices have recently attracted attentions both in dental and orthopedic device fields, which can tailor to the patients' anatomy to reduce the length of surgery time and to improve the clinical outcomes. However, development of the patient specific endovascular device still remains challenging due to the limitations in current 3D printing technology, specifically for the stent grafts. Therefore, our group has investigated the feasibility of a highly stretchable expanded-polytetrafluoroethylene (ePTFE) tube as a customizable graft material with the laser-welded nitinol backbone. In this study, a highly stretchable ePTFE tube was evaluated in terms of mechanical behaviors, in vitro biocompatibility of ePTFE with various stretchiness levels, and capability for the integration with the laser-welded customizable nitinol stent backbone. A prototype stent graft for the swine's venous size was successfully constructed and tested in the porcine model. This study demonstrates the ability of ePTFE tube to customize the stent graft without any significant issue, for example, sweating through the stretched pores in the ePTFE tube, as well as in vivo feasibility of the device for bleeding control. This novel customizable stent graft would offer possibilities for a wide range of both current and next-generation endovascular applications for the treatment in vascular injuries or diseases. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 911-923, 2019.

Damage control of caval injuries in a porcine model using a retrievable Rescue stent.

OBJECTIVE: Early hemorrhage control before the operating room is essential to reduce the significant mortality associated with traumatic injuries of the vena cava. Conventional approaches present logistical challenges on the battlefield or in the trauma bay. A retrievable stent graft would allow rapid hemorrhage control in the preoperative setting when endovascular expertise is not immediately available and without committing a patient to the limitations of current permanent stents. This study details a refined retrievable Rescue stent for percutaneous delivery that was examined in a porcine survival model of penetrating caval hemorrhage. METHODS: A retrievable caval stent was reduced in delivery profile to a 9F sheath using finite element analysis. The final stent was constructed with a "petal and stem" design using nitinol wire followed by covering with polytetrafluoroethylene. Seven Yorkshire pigs (79-86 kg) underwent 22F injury of the infrarenal vena cava with intentional class II hemorrhage (1200 mL). Percutaneous deployment of the Rescue stent was used to temporize hemorrhage for 60 minutes, followed by resuscitation with cell saver blood and permanent caval repair. Hemorrhage control was documented with photography and angiography. Vital signs were recorded and laboratory values were measured out to 48 hours postoperatively. Data were examined with a repeated-measures analysis of variance. RESULTS: The profile of the caval Rescue stent was successfully reduced from 16F to 9F while remaining within fracture and shape memory limits for nitinol. In addition, both rapid deployment and recapture were preserved. Following intentional hemorrhage after caval injury, animals revealed a significant drop in mean arterial pressure (average, 30 mm Hg), acidosis, and elevated lactate level compared with before injury. Compared with uncontrolled hemorrhage, which resulted in death in <9 minutes, the Rescue stent achieved hemorrhage control in <1 minute after venous access in all seven animals. All animals were successfully recovered after permanent repair. There was no significant change in levels of transaminases, bilirubin, creatinine, or hemoglobin at 48 hours compared with preinjury baseline. CONCLUSIONS: A retrievable Rescue stent achieved rapid percutaneous hemorrhage control after a significant traumatic injury of the vena cava and allowed successful recovery of all injured animals. Further development of this approach may have utility in preoperative damage control of caval injuries.

Advances in Materials for Recent Low-Profile Implantable Bioelectronics.

The rapid development of micro/nanofabrication technologies to engineer a variety of materials has enabled new types of bioelectronics for health monitoring and disease diagnostics. In this review, we summarize widely used electronic materials in recent low-profile implantable systems, including traditional metals and semiconductors, soft polymers, biodegradable metals, and organic materials. Silicon-based compounds have represented the traditional materials in medical devices, due to the fully established fabrication processes. Examples include miniaturized sensors for monitoring intraocular pressure and blood pressure, which are designed in an ultra-thin diaphragm to react with the applied pressure. These sensors are integrated into rigid circuits and multiple modules; this brings challenges regarding the fundamental material's property mismatch with the targeted human tissues, which are intrinsically soft. Therefore, many polymeric materials have been investigated for hybrid integration with well-characterized functional materials such as silicon membranes and metal interconnects, which enable soft implantable bioelectronics. The most recent trend in implantable systems uses transient materials that naturally dissolve in body fluid after a programmed lifetime. Such biodegradable metallic materials are advantageous in the design of electronics due to their proven electrical properties. Collectively, this review delivers the development history of materials in implantable devices, while introducing new bioelectronics based on bioresorbable materials with multiple functionalities.

A retrievable rescue stent graft and radiofrequency positioning for rapid control of noncompressible hemorrhage.

BACKGROUND: Noncompressible hemorrhage of the torso remains a challenging surgical dilemma. Stent graft repair requires endovascular expertise, imaging, and inventory that are not available within the critical window of massive hemorrhage. We developed a retrievable stent graft for rapid hemorrhage. We further investigated a radiofrequency (RF) positioning approach as a possible alternative to the logistics of fluoroscopy. METHODS: A retrievable stent graft was constructed with a novel "petal and stem" design from nitinol and covered with a sleeve of electrospun polyurethane. The stent graft was tested using an in vitro model of simulated hemorrhage. Next, the stent graft was examined in vivo using a porcine model of noncompressible hemorrhage. The stent was examined for hemorrhage control in a porcine model of either aortic or caval injury. An RF reader was assembled from an Arduino processor while RF tags were affixed to the ends of the stent graft. Detection accuracy of a handheld RF wand for an RF tag was quantified both in vitro and through tissue. RESULTS: The retrievable RESCUEstent graft was deployed within minutes and rapidly controlled traumatic hemorrhage angiographically in both aortic injury (n = 3) and caval injury (n = 2). Stent grafts were easily recaptured in both models in under 15 seconds. The LED light of a handheld RF detector illuminated when positioned directly over an RF tag. The RF detection approach revealed positioning accuracy to within 1 cm of the intended target, despite tissue interference. CONCLUSION: This study demonstrates the rapid deployment and retrieval of a RESCUE stent graft as well as the ability to tamponade injuries of the aorta and cava. In addition, this study demonstrates the feasibility of RF tags to guide stent placement through tissue. More rigorous models are needed to define the effectiveness of this approach in the setting of vascular injury and shock.

An in vivo pilot study of a microporous thin film nitinol-covered stent to assess the effect of porosity and pore geometry on device interaction with the vessel wall.

Sputter-deposited thin film nitinol constructs with various micropatterns were fabricated to evaluate their effect on the vessel wall in vivo when used as a covering for commercially available stents. Thin film nitinol constructs were used to cover stents and deployed in non-diseased swine arteries. Swine were sacrificed after approximately four weeks and the thin film nitinol-covered stents were removed for histopathologic evaluation. Histopathology revealed differences in neointimal thickness that correlated with the thin film nitinol micropattern. Devices covered with thin film nitinol with a lateral × vertical length = 20 × 40 µm diamond pattern had minimal neointimal growth with well-organized cell architecture and little evidence of ongoing inflammation. Devices covered with thin film nitinol with smaller fenestrations exhibited a relatively thick neointimal layer with inflammation and larger fenestrations showed migration of inflammatory and smooth muscle cells through the micro fenestrations. This "proof-of-concept" study suggests that there may be an ideal thin film nitinol porosity and pore geometry to encourage endothelialization and incorporation of the device into the vessel wall. Future work will be needed to determine the optimal pore size and geometry to minimize neointimal proliferation and in-stent stenosis.

A novel compartmentalised stent graft to isolate the perfusion of the abdominal organs.

Donation after cardiac death has been adopted to address the critical shortage of donor organs for transplant. Recovery of these organs is hindered by low blood flow that leads to permanent organ injury. We propose a novel approach to isolate the perfusion of the abdominal organs from the systemic malperfusion of the dying donor. We reasoned that this design could improve blood flow to organs without open surgery, while respecting the ethical principle that cardiac stress not be increased during organ recovery. Conditions within the stent were analysed using a computational fluid dynamics (CFD) method and validated on two prototypes in vitro. The hydrodynamic pressure drop across the stent was measured as 0.14-0.22 mmHg, which is a negligible influence. Device placement studies were also conducted on swine model fluoroscopically. All these results demonstrated the feasibility of rapidly isolating the perfusion to abdominal organs using a compartmentalised stent graft design.