Electrochemical Determination of Epinephrine in Pharmaceutical Preparation Using Laponite Clay-Modified Graphene Inkjet-Printed Electrode.

Epinephrine (EP, also called adrenaline) is a compound belonging to the catecholamine neurotransmitter family. It can cause neurodegenerative diseases, such as Alzheimer's disease, Parkinson's disease, Huntington's disease and amyotrophic lateral sclerosis. This work describes an amperometric sensor for the electroanalytical detection of EP by using an inkjet-printed graphene electrode (IPGE) that has been chemically modified by a thin layer of a laponite (La) clay mineral. The ion exchange properties and permeability of the chemically modified electrode (denoted La/IPGE) were evaluated using multi-sweep cyclic voltammetry, while its charge transfer resistance was determined by electrochemical impedance spectroscopy. The results showed that La/IPGE exhibited higher sensitivity to EP compared to the bare IPGE. The developed sensor was directly applied for the determination of EP in aqueous solution using differential pulse voltammetry. Under optimized conditions, a linear calibration graph was obtained in the concentration range between 0.8 µM and 10 µM. The anodic peak current of EP was directly proportional to its concentration, leading to detection limits of 0.34 µM and 0.26 µM with bare IPGE and La/IPGE, respectively. The sensor was successfully applied for the determination of EP in pharmaceutical preparations. Recovery rates and the effects of interfering species on the detection of EP were evaluated to highlight the selectivity of the elaborated sensor.

Lignocellulosic-Based Materials from Bean and Pistachio Pod Wastes for Dye-Contaminated Water Treatment: Optimization and Modeling of Indigo Carmine Sorption.

In this work, biomass lignocellulosic materials extracted via chemical and physical treatments from bean and pistachio pod waste were used for the optimized elimination of Indigo Carmine (IC) from aqueous medium, using a design of experiments methodology. The physicochemical properties of the studied materials (raw and treated counterparts) used for the sorption of IC were investigated by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with EDX, and thermal analysis. Key variables influencing the adsorption of IC, namely the initial IC concentration, the pH of the solution, the stirring time and the mass of adsorbents, were optimized by the central composite design (CCD) with three center points, the measured response being the amount of IC adsorbed. The optimal conditions obtained from the statistical analysis for the removal of IC were as follows: maximum adsorbed amounts of IC: 1.81 mg/g, 2.05 mg/g, 3.56 mg/g; 7.42 mg/g, 8.95 mg/g, 15.35 mg/g, for raw bean pods (RBS), BST1 and BST2 (bean pods chemically treated), and for raw pistachio pods (RPS), PST1 and PST2 (pistachio pods chemically treated), respectively. The pseudo-second-order nonlinear kinetics model well described the IC adsorption kinetics for RBS, BST1 and BST2, while the Elovich model was properly fitted by RPS, PST1, and PST2 biomaterials data. The Freundlich isotherm best described the shrinkage of IC on different sorbents. The good correlation of the experimental data of the IC with respect to the Freundlich isotherm indicated a multilayer adsorption with heterogeneous adsorption sites and different energies. The interest of this work consisted in developing analytical methods for the treatment of water polluted by dyes by using biosorbents, local biological materials widely available and inexpensive. The results collected in this work highlighted the interesting structural, morphological, and physico-chemical properties of the agro-waste used in the study, which properties allowed an important fixation of the target dye in solution. The research showed that the agro-waste used in the study are possible precursors to locally manufacture adsorbents at low cost, thus allowing the efficient removal of waste and dyes in liquid effluents.

Fabrication of an Organofunctionalized Talc-like Magnesium Phyllosilicate for the Electrochemical Sensing of Lead Ions in Water Samples.

A talc-like magnesium phyllosilicate functionalized with amine groups (TalcNH2), useful as sensor material in voltammetry stripping analysis, was synthesized by a sol-gel-based processing method. The characterizations of the resulting synthetic organoclay by scanning electron microscopy (SEM), X-ray diffraction, N2 sorption isotherms (BET method), Fourier transform infrared spectroscopy (FTIR), CHN elemental analysis and UV-Vis diffuse reflectance spectroscopy (UV-Vis-DRS) demonstrated the effectiveness of the process used for grafting of amine functionality in the interlamellar clay. The results indicate the presence of organic moieties covalently bonded to the inorganic lattice of talc-like magnesium phyllosilicate silicon sheet, with interlayer distances of 1568.4 pm. In an effort to use a talc-like material as an electrode material without the addition of a dispersing agent and/or molecular glue, the TalcNH2 material was successfully dispersed in distilled water in contrast to natural talc. Then, it was used to modify a glassy carbon electrode (GCE) by drop coating. The characterization of the resulting modified electrode by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) revealed its charge selectivity ability. In addition, EIS results showed low charge transfer resistance (0.32 Ω) during the electro-oxidation of [Fe(CN)6]3-. Kinetics studies were also performed by EIS, which revealed that the standard heterogeneous electron transfer rate constant was (0.019 ± 0.001) cm.s-1, indicating a fast direct electron transfer rate of [Fe(CN)6]3- to the electrode. Using anodic adsorptive stripping differential pulse voltammetry (DPV), fast and highly sensitive determination of Pb(II) ions was achieved. The peak current of Pb2+ ions on TalcNH2/GCE was about three-fold more important than that obtained on bare GCE. The calculated detection and quantification limits were respectively 7.45 × 10-8 M (S/N = 3) and 24.84 × 10-8 M (S/N 10), for the determination of Pb2+ under optimized conditions. The method was successfully used to tap water with satisfactory results. The results highlight the efficient chelation of Pb2+ ions by the grafted NH2 groups and the potential of talc-like amino-functionalized magnesium phyllosilicate for application in electrochemical sensors.

Amino-Functionalized Laponite Clay Material as a Sensor Modifier for the Electrochemical Detection of Quercetin.

In this work, an electrode modified with an amino-functionalized clay mineral was used for the electrochemical analysis and quantification of quercetin (QCT). The resulting amine laponite (LaNH2) was used as modifier for a glassy carbon electrode (GCE). The organic-inorganic hybrid material was structurally characterized using X-ray diffraction, Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and CHN elemental analysis. The covalent grafting of the organosilane to the clay backbone was confirmed. The charge on the aminated laponite, both without and with the protonation of NH2 groups, was evaluated via cyclic voltammetry. On the protonated amine (LaNH3+)-modified GCE, the cyclic voltammograms for QCT showed two oxidation peaks and one reduction peak in the range of -0.2 V to 1.2 V in a phosphate buffer-ethanol mixture at pH 3. By using the differential pulse voltammetry (DPV), the modification showed an increase in the electrode performance and a strong pH dependence. The experimental conditions were optimized, with the results showing that the peak current intensity of the DPV increased linearly with the QCT concentration in the range from 2 × 10-7 M to 2 × 10-6 M, leading to a detection limit of 2.63 × 10-8 M (S/N 3). The sensor selectivity was also evaluated in the presence of interfering species. Finally, the proposed aminated organoclay-modified electrode was successfully applied for the detection of QCT in human urine. The accuracy of the results achieved with the sensor was evaluated by comparing the results obtained using UV-visible spectrometry.

Hydroxyapatite/L-Lysine Composite Coating as Glassy Carbon Electrode Modifier for the Analysis and Detection of Nile Blue A.

An amperometric sensor was developed by depositing a film coating of hydroxyapatite (HA)/L-lysine (Lys) composite material on a glassy carbon electrode (GCE). It was applied for the detection of Nile blue A (NBA). Hydroxyapatite was obtained from snail shells and its structural properties before and after its combination with Lys were characterized using X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) surface area analyses. The coupling of Lys to HA was attributed to favorable interaction between negatively charged -COO- groups of Lys and divalent ions Ca2+ of HA. Electrochemical investigations pointed out the improvement in sensitivity of the GCE/Lys/HA sensor towards the detection of NBA in solution. The dependence of the peak current and potential on the pH, scan rate, and NBA concentration was also investigated. Under optimal conditions, the GCE/Lys/HA sensor showed a good reproducibility, selectivity, and a NBA low detection limit of 5.07 × 10-8 mol L-1. The developed HA/Lys-modified electrode was successfully applied for the detection of NBA in various water samples.

Sensitive Electrochemical Sensor Based On an Aminated MIL-101(Cr) MOF for the Detection of Tartrazine.

The aminated metal-organic framework H2N-MIL-101(Cr) was used as the carbon paste electrode (CPE) modifier for the determination of tartrazine (Tz) in soft drinks. The amino material was characterized by electrochemical impedance spectroscopy and showed significantly faster electron transfer with lower charge-transfer resistance (0.13 kΩ) compared to the electrode modified with the unfunctionalized MIL-101(Cr) material (1.1 kΩ). The H2N-MIL-101(Cr)-modified CPE [H2N-MIL-101(Cr)-CPE] was then characterized by cyclic voltammetry (CV) using [Fe(CN)6]3- and [Ru(NH3)6]3+ ions as the redox probes, showing good accumulation of [Fe(CN)6]3- ions on the electrode surface. A CV scan of Tz in Britton Robinson buffer solution revealed an irreversible system with an oxidation peak at +0.998 V versus Ag/AgCl/KCl. Using CV and differential pulse voltammetry, an electrochemical method for quantifying Tz in aqueous medium was then developed. Several parameters that affect the accumulation and detection steps were optimized. Optimal detection of Tz was achieved after 180 s of accumulation in Britton Robinson buffer solution (pH 2) using 2 mg of H2N-MIL-101(Cr) material. Under optimal conditions, the sensor exhibited a linear response in the concentration range of 0.004-0.1 µM and good detection sensitivity (35.4 µA µM-1), and the detection limit for Tz was found to be 1.77 nM (S/N = 3). Satisfactory repeatability, stability, and anti-interference performance were also achieved on H2N-MIL-101(Cr)-CPE. The sensor was applied to commercial juices, and the results obtained were approximately similar to those given by UV-vis spectrophotometry.

Electrochemistry-coupled to liquid chromatography-mass spectrometry-density functional theory as a new tool to mimic the environmental degradation of selected phenylurea herbicides.

In vitro and in vivo experimental models, mainly based on cell cultures, animals, healthy humans and clinical trials, are useful approaches for identifying the main metabolic pathways. However, time, cost, and matrix complexity often hinder the success of these methods. In this study, we propose an alternative non-enzymatic method, using electrochemistry (EC) coupled to liquid chromatography (LC) - high resolution mass spectrometry (HRMS) - DFT theoretical calculations (EC/LC-MS/DFT) for the mimicry/simulation of the environmental degradation of phenylurea herbicides, and for the mechanism elucidation of this class of herbicides. Fenuron, monuron, isoproturon, linuron, monolinuron, metoxuron and chlortoluron were selected as relevant model compounds. The intended compounds are oxidized by EC, separated by LC and detected using electrospray ionization HRMS. The main oxidation products were hydroxylated compounds obtained by substitution and addition reactions. Unstable quinone imines/methines, rarely observed by conventional methods, have been identified during the oxidative degradation of phenylurea herbicides for the first time in this study. Some were directly observed and the others were trapped by glutathione GSH. Reactions such as hydrolytic substitutions (-Cl/+OH and -C3H7/+OH and -CH3/+OH and -OCH3/+OH), aromatic hydroxylation, alkyl carbon hydroxylation, dehydrochlorination/dehydromethylation/dehydromethoxylation and conjugation have been successfully mimicked. The obtained results, supported by theoretical calculations, are useful for simulating/understanding and predicting the oxidative degradation pathways of pesticides in the environment.

Using electrochemistry coupled to high resolution mass spectrometry for the simulation of the environmental degradation of the recalcitrant fungicide carbendazim.

Currently, there is a growing interest in the study of environmental degradation pathways of organic contaminants such as pesticides, with the objective to better understand their potential risk for environmental systems and living organisms. In this context, DFT (conceptual density functional theory) and predictive methods may systematically be used to simplify and accelerate the elucidation of environmental degradation. We report herein the electrochemical behavior/degradation of the carbendazim (CBZ) fungicide widely used to treat cereal and fruit crops. Oxidative degradation of CBZ was studied using an electrochemical flow-through cell directly coupled to a mass spectrometer for rapid identification of CBZ degradation products. The structural elucidation of CBZ oxidation products was based on retention time, accurate mass, isotopic distribution and fragmentation pattern by using LC-HRMS an LC-HRMS2. The most important chemical reactions found to occur in the transformation of CBZ were hydrolysis and hydroxylation. EC-LC-MS and EC-MS analysis has made it possible to highlight the identification of degradation products of CBZ. In addition to previously known transformation products common to those observed during environmental degradation (monocarbomethoxyguanidine, benzimidazole-isocyanate, 2-aminobenzimidazole, hydroxy-2-aminobenzimidazole, hydroxycarbendazim, CBZ-CBZ dimer), two new degradation products were identified in this work: a quinone imine and a nitrenium ion. Electrochemistry mass spectrometry hyphenated techniques represent an accessible, rapid and reliable tool to elucidate the oxidative degradation of CBZ, including reactive degradation products and conjugates.

A Low-Cost Layered Double Hydroxide (LDH) Based Amperometric Sensor for the Detection of Isoproturon in Water Using Carbon Paste Modified Electrode.

In this work, a Layered Double Hydroxide (NiAl-LDH) was obtained by coprecipitation method and used to elaborate an electrochemical sensor for the determination of isoproturon, which is a hazardous pollutant, widely used in agriculture, and its residue is distributed into aqueous environment through run-off and leaching from the soil. Various physicochemical techniques such as FT-IR spectroscopy, X-ray diffraction, and thermal analysis were used to characterize this material. The anionic exchange capacity of NiAl-LDH on carbon paste modified electrode was investigated toward [Fe(CN)6]3- using cyclic voltammetry. Used as electrode modifier of carbon paste electrode for isoproturon detection, a remarkable increase in isoproturon signal on modified carbon paste electrode by LDH was observed. The peak current obtained after 3 min of preconcentration in 25 µM ISO on NiAl-LDH/CPE was 2.6 times higher than that exhibited by the same analyte on the unmodified CPE, thereby opening the way to the development of a sensitive method for the detection of ISO. Other parameters that can affect the stripping response (preconcentration time, pH of detection medium, and LDH loading within the paste) were investigated to optimize the proposed sensor. After optimization, a linear calibration curve was obtained in the concentration range from 2 × 10-8 to 1.8 × 10-7 M, leading to a detection limit of 1 × 10-9 M (S/N = 3). The relative standard deviation for 5 identical measurements was 2.7%. The interfering effect of some compounds and ions was examined on the stripping response of ISO. The applicability of the method was verified by the determination of ISO in spiked water sample.

Indigo Carmine and 2,6-Dichlorophenolindophenol Removal Using Cetyltrimethylammonium Bromide-Modified Palm Oil Fiber: Adsorption Isotherms and Mass Transfer Kinetics.

In the present work, the usefulness of cetyltrimethylammonium bromide-modified palm oil fiber (CTAB-modified POF) for the removal of indigo carmine (IC) and 2,6-dichlorophenolindophenol (2,6-DCPIP) from aqueous solutions was investigated. Raw, NaOH-treated, and CTAB-modified POF were characterized by Fourier-transform infrared (FT-IR) spectroscopy, elemental analysis, thermogravimetric-hyperdifferential scanning calorimetric (TG-HDSC) analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The adsorption studies of IC and 2,6-DCPIP were performed in batch mode using CTAB-modified POF. The results showed that equilibrium was attained after a contact time of 30 minutes for IC and 20 minutes for 2,6-DCPIP. The maximum capacity of adsorption was obtained at pH = 2. The capacity of adsorption considerably increased with modified biosorbents and with increasing initial concentration of dyes. The ionic strength favors the increasing adsorption capacity of IC and does not affect the adsorption capacity of 2,6-DCPIP. The percentage of adsorption increased with increasing mass of the biosorbents. The nonlinear regression of adsorption isotherms showed that Freundlich (r 2 = 0.953; χ 2 = 4.398) and Temkin (r 2 = 0.986; χ 2 = 1.196) isotherms are most appropriate to describe the adsorption of IC and 2,6-DCPIP on CTAB-modified POF, respectively. The maximum adsorption capacities determined by the Langmuir isotherm were 275.426 and 230.423 µmol·g-1 for IC and 2,6-DCPIP, respectively. The linear regression of adsorption kinetics was best described by the pseudo-second-order model (R 2 ≥ 0.998). The diffusion mechanism showed that external mass transfer is the main rate controlling step. Desorption of the two dyes is favorable in the alkaline medium.

Electrochemical analysis of methylparathion pesticide by a gemini surfactant-intercalated clay-modified electrode.

In this study, an hybrid material obtained by the intercalation of a gemini surfactant between the layers of smectite-type clay, was fully characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR) and N(2) adsorption-desorption experiments (BET method). To ascertain the intercalation process of the starting clay by the dimeric surfactant, the permselectivity and ion exchange properties of the organoclay were investigated by ion exchange voltammetry using [Fe(CN)(6)](3-) and [Ru(NH(3))(6)](3+) as redox probes, by the means of a clay film-modified electrode. Due to its organophilic character, the surfactant-intercalated complex was evaluated as electrode modifier for the accumulation of methylparathion (MP) pesticide. The electroanalytical procedure involves two steps: preconcentration under open-circuit followed by voltammetric detection by square wave voltammetry: the peak current obtained (after 5min preconcentration in 4x10(-5)molL(-1)MP) on a glassy carbon electrode coated by a thin film of the modified clay was more than five times higher than that exhibited by the same substrate covered by a film of the pristine clay. This opens the way to the development of a sensitive method for the detection of the pesticide. Many parameters that can affect the stripping response (surfactant loading of the hybrid material, film composition, pH of the detection medium, preconcentration time, electrolysis potential and duration as well as some other instrumental parameters) were systematically investigated to optimize the sensitivity of the organoclay-modified electrode. After optimization, a linear calibration curve for MP was obtained in the concentration range from 4x10(-7) to 8.5x10(-6)molL(-1) in acetate buffer (pH 5), with a detection limit of 7x10(-8)molL(-1) (signal-to-noise ratio equal to 3). The interference effect of various inorganic ions likely to influence the stripping determination of the pesticide was also examined, and the described method was applied to spring water analysis.