RESUMEN
Background: Not all surgical osteotomy steps have been properly investigated for their potential impact on surgical accuracy. The main study objective was to investigate the osteotomy parameters that have respectively major and minor impact on coronal and sagittal bony accuracy in medial opening-wedge high tibial osteotomy (MOWHTO). Methods: Three tibias from an existing 3D MOWHTO osteotomy database were chronologically selected based on segmentation quality, tibial plateau size and the presence of tibial varus. The study consisted of three parts: (I) translating the hinge axis in the coronal plane and switching the osteotomy starting point (30-40 mm) and depth, (II) the hinge axis was rotated stepwise by 10° to perform five simulations, (III) the hinge axis was rotated in the axial plane stepwise by 10° towards anterolateral to perform four simulations (0°, +10°, +20°, +30°). The medial proximal tibial angle (MPTA) and lateral tibial slope were the primary outcomes. Simulations were performed with 5, 10 and 15 mm gap distraction. Results: In the coronal plane, maximum difference in osteotomy depth was 10 mm which represented an MPTA difference of 0.8°-1.1° in 10 mm gap distraction and 1.2°-2.0° in 15 mm gap distraction. Tibial slope remained unchanged. Rotating the hinge axis in the sagittal plane delivered minor changes on both MPTA (<0.5°) and tibial slope (<1.5°) at 10 mm gap distraction. Per 10° of axial rotation of the hinge axis towards anterolateral, the tibial slope increased by 1.0°-1.3° in 10 mm gap distraction while the MPTA remains nearly unchanged. Conclusions: The study showed that the medio-lateral osteotomy length is the main parameter for obtaining bony accuracy in the coronal plane and maintaining a strict perpendicular axial hinge axis position is crucial in preserving the native tibial slope. Correct axial alignment of the hinge axis can be obtained by creating an equal osteotomy depth of the anterior and posterior tibial cortices in the lateral metaphyseal area.
RESUMEN
Purpose: The study aims to identify differences in tibiofemoral joint morphology between responders (R group, no pain) to arthroscopic partial medial meniscectomy (APMM) versus medial postmeniscectomy syndrome patients (MPMS group, recurrent pain at 2 years postmeniscectomy) in a clinically neutrally aligned patient population. The second aim was to build a morphology-based predictive algorithm for response to treatment (RTT) in APMM. Methods: Two patient groups were identified from a large multicentre database of meniscectomy patients at 2 years of follow-up: the R group included 120 patients with a KOOS pain score > 75, and the MPMS group included 120 patients with a KOOS pain score ≤ 75. Statistical shape models (SSMs) of distal femur, proximal tibia and tibiofemoral joint were used to compare knee morphology. Finally, a predictive model was developed to predict RTT, with the SSM-derived morphologic variables as predictors. Results: No differences were found between the R and MPMS groups for patient age, sex, height, weight or cartilage status. Knees in the MPMS group were significantly smaller, had a wider femoral notch and a smaller medial femoral condyle. A morphology-based predictive model was able to predict MPMS at 2 years follow-up with a sensitivity of 74.9% (95% confidence interval [CI]: 74.4%-75.4%) and a specificity of 81.0% (95% CI: 80.6%-81.5%). Conclusion: A smaller tibiofemoral joint, a wider intercondylar notch and smaller medial femoral condyle were observed shape variations related to medial postmeniscectomy syndrome. These promising results are a first step towards a knee morphology-based clinical decision support tool for meniscus treatment. Study Design: Case-control study. Level of Evidence: Level IIIb.
RESUMEN
Manual anatomical landmarking for morphometric knee bone characterization in orthopedics is highly time-consuming and shows high operator variability. Therefore, automation could be a substantial improvement for diagnostics and personalized treatments relying on landmark-based methods. Applications include implant sizing and planning, meniscal allograft sizing, and morphological risk factor assessment. For twenty MRI-based 3D bone and cartilage models, anatomical landmarks were manually applied by three experts, and morphometric measurements for 3D characterization of the distal femur and proximal tibia were calculated from all observations. One expert performed the landmark annotations three times. Intra- and inter-observer variations were assessed for landmark position and measurements. The mean of the three expert annotations served as the ground truth. Next, automated landmark annotation was performed by elastic deformation of a template shape, followed by landmark optimization at extreme positions (highest/lowest/most medial/lateral point). The results of our automated annotation method were compared with ground truth, and percentages of landmarks and measurements adhering to different tolerances were calculated. Reliability was evaluated by the intraclass correlation coefficient (ICC). For the manual annotations, the inter-observer absolute difference was 1.53 ± 1.22 mm (mean ± SD) for the landmark positions and 0.56 ± 0.55 mm (mean ± SD) for the morphometric measurements. Automated versus manual landmark extraction differed by an average of 2.05 mm. The automated measurements demonstrated an absolute difference of 0.78 ± 0.60 mm (mean ± SD) from their manual counterparts. Overall, 92% of the automated landmarks were within 4 mm of the expert mean position, and 95% of all morphometric measurements were within 2 mm of the expert mean measurements. The ICC (manual versus automated) for automated morphometric measurements was between 0.926 and 1. Manual annotations required on average 18 min of operator interaction time, while automated annotations only needed 7 min of operator-independent computing time. Considering the time consumption and variability among observers, there is a clear need for a more efficient, standardized, and operator-independent algorithm. Our automated method demonstrated excellent accuracy and reliability for landmark positioning and morphometric measurements. Above all, this automated method will lead to a faster, scalable, and operator-independent morphometric analysis of the knee.
RESUMEN
Background: Posterolateral tibial plateau impaction fractures occur frequently associated with anterior cruciate ligament (ACL) tears. Some authors advocate operative treatment of high-grade impaction fractures, which has led to the development of classification systems. Our study aims (1) to describe and compare the intra- and interobserver reliability of the two most used classifications and (2) to assess correlations between the grade of bony posterolateral tibial injury, patient characteristics and short-to mid-term revision rate after ACL reconstruction. Materials and methods: In a retrospective series of 163 patients who underwent ACL reconstruction, two reviewers independently evaluated the preoperative MRI scans. Conform the Menzdorf and Bernholt classification the presence and grade of an associated posterolateral impaction fracture were assessed. Statistical analyses were performed to test for both study hypotheses. Results: 171 primary ACL cases were evaluated. Mean follow-up time was 41 months (range 12-154, SD = 17.1). Mean age was 32 years (range 13-59, SD = 12). Posterolateral impaction fractures were present in 111 (64.9 %) and 120 (70.0 %) cases, according to the Menzdorf and Bernholt classification. A Segond fracture was present in 19 (11.1 %) cases. Kappa value was 0.47 for intra- and 0.52 for the interobserver reliability for the Menzdorf classification (moderate reliability). For the Bernholt classification kappa values were 0.66 and 0.61, respectively (good reliability). A Segond fracture correlated significantly with the presence of a posterolateral impaction fracture (p < 0.05). A significant association was present between patients necessitating ACL revision surgery and patients for whom operative intervention for the posterolateral impression was advised following the Menzdorf classification (p < 0.001). Conclusion: Inter- and intraobserver reliability testing for classifying posterolateral tibial fractures resulted in moderate to good reliability. High-grade posterolateral tibial fractures should be identified, selective treatment should be considered as they are associated with higher revision rates after ACL reconstruction if left untreated.
RESUMEN
PURPOSE: There is high variability in femoral torsion, measured on two-dimensional (2D) computed tomography (CT) scans. The aim of this study was to find a reliable three-dimensional (3D) femoral torsion measurement method, assess the influence of CAM deformity on femoral torsion measurement, and to promote awareness for the used measurement method. METHODS: 3D models of 102 dry femur specimens were divided into a CAM and non-CAM group. Femoral torsion was measured by one 2D-CT method described by Murphy et al. (method 0) and five 3D methods. The 3D methods differed in strategies to define the femoral neck axis. Method 1 is based on an elliptical least-square fit at the middle of the femoral neck. Methods 2 and 3 defined the centre of mass of the entire femoral neck and of the most cylindrical part, respectively. Methods 4 and 5 were based on the intersection of the femoral neck with a 25% and 40% enlarged best fit sphere of the femoral head. RESULTS: 3D methods resulted in higher femoral torsion measures than the 2D method; the mean torsion for method 0 was 8.12° ± 7.30°, compared to 9.93° ± 8.24° (p < 0.001), 13.21° ± 8.60° (p < 0.001), 8.21° ± 7.64° (p = 1.00), 9.53° ± 7.87° (p < 0.001) and 10.46° ± 7.83° (p < 0.001) for methods 1 to 5 respectively. In the presence of a CAM, torsion measured with method 4 is consistently smaller than measured with method 5. CONCLUSION: 2D measurement might underestimate true femoral torsion and there is a difference up to 5°. There is a tendency for a higher mean torsion in hips with a CAM deformity. Methods 4 and 5 are the most robust techniques. However, method 4 might underestimate femoral torsion if a CAM deformity is present. Since method 5 is independent of a CAM deformity, it is the preferred technique to define expected values of torsion.
RESUMEN
The lateral tibial spine (LTS) is frequently proposed as a correction target in high tibial osteotomy (HTO), although little is known about its exact radiographic position. This study primarily aims to define the position and variance of the LTS. Secondly, this study wants to investigate the relevance of the LTS position on the mechanical tibiofemoral angle (mTFA°) while planning and postoperatively landing the weight-bearing line (WBL) on this landmark. The LTS position was studied on preoperative full-leg standing radiographs (FLSR) and computed tomography (CT) scans in 70 cases. 3D models of the tibia were created in Mimics 23.0 and measurements were conducted in 3-matic 15.0 (Materialise, Leuven®). Next, 100 HTO cases were retrospectively planned with the WBL through the LTS according to Dugdale's method on FLSR. Finally, 55 postoperative FLSR which had the WBL on the LTS (±2%) were assessed for mTFA° outcome. Statistics were conducted in GraphPad 8.0. The LTS was located at 58.3%±1.9 [55-63%] in 2D and 57.3%±2.2 [53-63%] in 3D showing a high correlation (r=0.77 [0.65 to 0.85]). The planned mTFA on the LTS was 181.8°±0.3 (181.3°-182.5°). On postoperative FLSR, the mTFA was 182.2°±0.6 (180.9°-183.1°). The lateral tibial spine is located at 57-58% on the tibial plateau with a 10% maximal variation range. Good agreement was found between 2D and 3D imaging modalities while evaluating its position in the coronal plane. When aiming the WBL through the LTS during valgus-producing HTO, a consistent realignment of 181-183° mTFA can be expected when performing accurate surgery.
Asunto(s)
Osteoartritis de la Rodilla , Tibia , Humanos , Tibia/diagnóstico por imagen , Tibia/cirugía , Estudios Retrospectivos , Articulación de la Rodilla/diagnóstico por imagen , Articulación de la Rodilla/cirugía , Extremidad Inferior , Osteotomía/métodos , Osteoartritis de la Rodilla/diagnóstico por imagen , Osteoartritis de la Rodilla/cirugíaRESUMEN
PURPOSE: Contemporary medial opening wedge high tibial osteotomy (MOWHTO) still seems to struggle with inconsistent accuracy outcomes. Our objective was to assess surgical accuracy and short-term clinical outcomes when using 3D planning and a patient-specific instrumentation (PSI) kit to prepare customized bone allografts. METHODS: Thirty subjects (age 48y ± 13) were included in a double-center prospective case series. A low-dose CT-scan was performed to generate 3D bone models, a MOWHTO was simulated, and PSI was designed and 3D printed based on the complementary negative of the planned osteotomy gap. Clinical outcome was assessed at two, four, 12 weeks and one year using NRS, KOOS, UCLA activity score, EQ-5D and anchor questions. A linear-mixed model approach was implemented for data analysis. RESULTS: Preoperative 3D values were 175.0° ± 2.2 mechanical tibiofemoral angle (mTFA), 85.0° ± 3.0 medial proximal tibial angle (MPTA), and 94.1° ± 3.4 medial posterior tibial slope (MPTS). Target planning ranged from slight varus to the lateral tibial spine (slight valgus). Postoperative 3D analysis showed an accuracy of 1.1° ± 0.7 ΔMPTA (p = 0.04) and 1.2° ± 1.2 ΔMPTS (p = 0.11). NRS decreased from baseline 6.1 ± 1.9 to 2.7 ± 1.9 at four weeks (p < 0.001) and 1.7 ± 1.9 at one year (p < 0.001). KOOS increased from 31.4 ± 17.6 to 50.6 ± 20.6 at 12 weeks (p < 0.001) and to 71.8 ± 15.6 at one year (p < 0.001). CONCLUSION: The study suggests that 3D printed instrumentation to personalize structural bone allograft is a viable alternative method in MOWHTO that has the benefit of optimizing surgical accuracy while providing early and consistent pain relief after surgery.
RESUMEN
One of the reasons for failure of total elbow replacement is loosening of the ulnar component. Cementing techniques are often outdated. A special small nozzle is needed for the ulnar component, when a cement gun is used. This may not always be available, or surgeons may prefer to use a syringe. We postulated that the use of a cement gun and smaller nozzle would result in improved filling of the ulnar canal. A cadaveric study was performed in which the ulnas of paired specimens were cemented with a cement gun or with a syringe. A 3D printed ulnar component was inserted and computed tomography scanning was performed on all specimens. Filling of the ulnar intramedullary canal was analysed using 3D reconstructions of the specimens. A greater degree of filling was seen by the use of the cement gun in 85.7%. Filling was 52.7% in the syringe group (25.1-78.7%), compared to 63.3% for the cement gun group (p < 0.05). The use of a small nozzle cement gun provided a significantly higher filling degree of the ulnar canal. We recommend to always use a cement gun with a specific small nozzle to cement the ulnar component in total elbow arthroplasty.
RESUMEN
PURPOSE: Early-onset degeneration of the knee is linked to genetics, overload, injury, and potentially, knee morphology. The purpose of this study is to explore the characteristics of the small medial femoral condyle, as a distinct knee morphotype, by means of a landmark-based three-dimensional (3D) analysis and statistical parametric mapping. METHODS: Sixteen knees with a small medial femoral condyle (SMC) were selected from a database of patients with distinct knee joint anatomy and 16 gender-matched knees were selected from a control group database. 3D models were generated from the medical imaging. After normalization for size, a set of pre-defined landmark-based parameters was analysed for the femur and tibia. Local shape differences were evaluated by matching all bone surfaces onto each other and comparing the distances to the mean control group bone shape. RESULTS: The small medial condyle group showed a significant association with medial compartment degeneration and had a 4% and 13% smaller medial condyle anteroposteriorly and mediolaterally, whereas the distal femur was 3% wider mediolaterally. The lateral condyle was 2% smaller anteroposteriorly and 8% wider mediolaterally. The complete tibial plateau was 3% smaller mediolaterally and the medial tibial plateau was 6% smaller. CONCLUSION: A new knee morphotype demonstrated an increased risk for medial compartment degeneration and was differentiated from a healthy control group based on the following morphological characteristics: a smaller medial femoral condyle and medial tibial plateau, a wider lateral femoral condyle and a wider distal femur on a smaller tibial plateau. This pilot study suggests a role for the SMC knee morphotype in the multifactorial process of medial compartment degeneration. LEVEL OF EVIDENCE: III.
Asunto(s)
Fémur/anatomía & histología , Articulación de la Rodilla/anatomía & histología , Osteoartritis/patología , Adulto , Epífisis/anatomía & histología , Epífisis/diagnóstico por imagen , Femenino , Fémur/diagnóstico por imagen , Humanos , Imagenología Tridimensional/métodos , Articulación de la Rodilla/diagnóstico por imagen , Imagen por Resonancia Magnética/métodos , Masculino , Menisco/anatomía & histología , Menisco/diagnóstico por imagen , Persona de Mediana Edad , Proyectos Piloto , Radiografía/métodos , Tibia/anatomía & histología , Tibia/diagnóstico por imagenRESUMEN
A novel approach for opening-wedge high tibial osteotomy (OWHTO) with patient-specific instrumentation (PSI) was evaluated for its safety, feasibility, and accuracy. Next, the mechanical medial proximal tibial angle (mMPTA) was assessed as a potential planning angle by investigating the relation with the mechanical femorotibial angle (mFTA). Ten OWHTO cases were 3D planned using the mMPTA and operated with a customized 3D-printed wedge and cast which resembled the intended osteotomy opening. Patients were closely monitored for intraoperative and postoperative complications up to 1 year after surgery. Radiological assessment was conducted on full leg standing radiographs and supine lower limb computed tomography-scans preoperatively and 3 months after surgery. No intraoperative complications or logistical issues during PSI processing were observed. Absolute accuracy outcomes showed a correction error of 1.3° ± 1.1 mMPTA and 0.9° ± 0.6 mFTA with all osteotomies falling in (-2°; + 2°) mFTA around the target. The mMPTA and mFTA were found to have a strong correlation in both 3D (r = 0.842, p = 0.002) and 2D (r = 0.766, p = 0.01) imaging for effective correction. The study confirmed the development of a safe and feasible PSI technique in OWHTO with excellent accuracy outcomes. The strong correlation between the mMPTA and mFTA indicated that soft tissue changes after OWHTO are of minor significance to the final alignment in ligament-stable patients. Finally, the mMPTA was found to be a reliable planning angle in 3D software for obtaining the intended lower limb realignment and its use can therefore be recommended in modern OWHTO planning.
Asunto(s)
Osteoartritis de la Rodilla , Estudios de Factibilidad , Humanos , Articulación de la Rodilla/diagnóstico por imagen , Articulación de la Rodilla/cirugía , Osteoartritis de la Rodilla/diagnóstico por imagen , Osteoartritis de la Rodilla/cirugía , Osteotomía , Radiografía , Estudios Retrospectivos , Tibia/diagnóstico por imagen , Tibia/cirugíaRESUMEN
PURPOSE: The trochlear dysplastic femur has a specific morphotype previously characterised by not only dysplastic features of the trochlea but also by specific features of the notch and posterior femur. In this study the morphology of the tibia and patella was investigated to gain further insight in the complete geometrical complexity of the trochlear dysplastic knee. METHODS: Arthro-CT scan-based 3D models of 20 trochlear dysplastic and 20 normal knees were uniformly scaled and landmarks and landmark-based reference planes were created to quantify a series of morphometric characteristics of the tibia and patella. RESULTS: In the mediolateral direction, the 3D-analysis revealed a 3% smaller medial tibial plateau (30.4 ± 1.6 mm vs 31.5 ± 1.6 mm), a 3% smaller overall width of the tibial plateau (73.6 ± 2.0 mm vs 75.7 ± 2.0 mm), a 16% smaller medial facet (17.3 ± 2.2 mm vs 20.1 ± 1.3 mm) and a 4% smaller overall width of the patella (41.7 ± 2.5 mm vs 43.4 ± 2.3 mm) in trochlear dysplastic knees. In the anteroposterior direction, the lateral tibial plateau of trochlear dysplastic knees was 5% larger (37.2 ± 2.3 mm vs 35.5 ± 3.1 mm). A correlation test between the width of the femur and the width of the tibia revealed that trochlear dysplastic knees show less correspondence between the femur and tibia compared to normal knees. CONCLUSION: Significant differences in the morphology of the tibial plateau and patella were detected between trochlear dysplastic and normal knees. Both in the trochlear dysplastic tibial plateau and patella a narrower medial compartment leads to a significant smaller overall mediolateral width. These findings are important for the understanding of knee biomechanics and the design of total knee arthroplasty components. LEVEL OF EVIDENCE: III.
Asunto(s)
Puntos Anatómicos de Referencia/diagnóstico por imagen , Puntos Anatómicos de Referencia/patología , Rótula/diagnóstico por imagen , Rótula/patología , Tibia/diagnóstico por imagen , Tibia/patología , Adolescente , Adulto , Artroplastia de Reemplazo de Rodilla , Artroscopía , Fenómenos Biomecánicos , Simulación por Computador , Femenino , Humanos , Imagenología Tridimensional , Masculino , Rótula/cirugía , Valores de Referencia , Tibia/cirugía , Tomografía Computarizada por Rayos X , Adulto JovenRESUMEN
In malunion cases, restoration of anatomy is a key factor in obtaining a good functional outcome, but this can be technically very challenging.Three-dimensional printed bone models can further improve understanding of the malunion pattern.The use of three-dimensional (3D) computer planning, and the assembly of patient-specific instruments and implants, especially in complex deformities of the upper limb, allow accurate correction while reducing operation time, blood loss volume and radiation exposure during surgery.One of the major disadvantages of the 3D technique is the additional cost because it requires specific computer software, a dedicated clinical engineer, and a 3D printer.Further technical developments and clinical investigations are necessary to better define the added value and cost/benefit relationship of 3D in the treatment of complex fractures, non-unions, and malunions. Cite this article: EFORT Open Rev 2019;4 DOI: 10.1302/2058-5241.4.180074.
RESUMEN
Malunion is a common complication of distal radius fractures, especially those treated conservatively. In clinical studies, a significant correlation between anatomic reduction and wrist function has been shown. Corrective osteotomy is the preferred treatment for symptomatic cases, notwithstanding the technical challenges. The use of computer simulation improves pre-operative understanding of the three-dimensional deformity. Patient-specific surgical guides, based on precise pre-operative planning, lead to superior perioperative accuracy and reproducibility. The pre-operative planning and surgical technique of distal radius corrective surgery using three-dimensional computer technology are described in detail. The preliminary results demonstrate the excellent clinical and radiographic outcome of this technique.
Asunto(s)
Fracturas Mal Unidas/cirugía , Osteotomía/métodos , Fracturas del Radio/cirugía , Adolescente , Adulto , Anciano , Simulación por Computador , Femenino , Fijación de Fractura/métodos , Fracturas Mal Unidas/fisiopatología , Fuerza de la Mano/fisiología , Humanos , Imagenología Tridimensional , Masculino , Persona de Mediana Edad , Planificación de Atención al Paciente , Cuidados Preoperatorios/métodos , Estudios Prospectivos , Fracturas del Radio/fisiopatología , Rango del Movimiento Articular/fisiología , Resultado del Tratamiento , Adulto JovenRESUMEN
PURPOSE: Three-dimensional planning based on computed tomography images of the malunited and the mirrored contralateral forearm allows preoperative simulations of corrective osteotomies, the fabrication of patient-specific osteotomy guides, and custom-made 3-dimensional printed titanium plates. This study aims to assess the precision and clinical outcome of this technique. METHODS: This was a prospective pilot study with 5 consecutive patients. The mean age at initial injury was 11 years (range, 4-16 years), and the mean interval from the time of injury to the time of corrective surgery was 32 months (range, 7-107 months). Patient-specific osteotomy guides and custom-made plates were used for multiplanar corrective osteotomies of both forearm bones at the distal level in 1 patient and at the middle-third level in 4 patients. Patients were assessed before and after surgery after a mean follow-up of 42 months (range, 29-51 months). RESULTS: The mean planned angular corrections of the ulna and radius before surgery were 9.9° and 10.0°, respectively. The mean postoperative corrections obtained were 10.1° and 10.8° with corresponding mean errors in correction of 1.8° (range, 0.3°-5.2°) for the ulna and 1.4° (range, 0.2°-3.3°) for the radius. Forearm supination improved significantly from 47° (range, 25°-75°) before surgery to 89° (range, 85°-90°) at final review. Forearm pronation improved from 68° (range, 45°-84°) to 87° (range, 82°-90°). In addition, there was a statistically significant improvement in pain and grip strength. CONCLUSIONS: This study demonstrates that 3-dimensional planned patient-specific guides and implants allow the surgeon to perform precise corrective osteotomies of complex multiplanar forearm deformities with satisfactory preliminary results. TYPE OF STUDY/LEVEL OF EVIDENCE: Therapeutic V.
Asunto(s)
Fijación Interna de Fracturas/instrumentación , Fracturas Mal Unidas/cirugía , Fijadores Internos , Osteotomía , Fracturas del Radio/cirugía , Fracturas del Cúbito/cirugía , Adolescente , Niño , Preescolar , Diáfisis/lesiones , Femenino , Fracturas Mal Unidas/diagnóstico por imagen , Humanos , Imagenología Tridimensional , Masculino , Proyectos Piloto , Estudios Prospectivos , Fracturas del Radio/diagnóstico por imagen , Cirugía Asistida por Computador , Tomografía Computarizada por Rayos X , Fracturas del Cúbito/diagnóstico por imagenRESUMEN
Purpose We evaluated clinical and radiographic outcome of percutaneous transtrapezial fixation of the scaphoid delayed union or nonunion using a headless bone screw without bone grafting. Methods Sixteen patients with delayed union or nonunion of the scaphoid were included in this retrospective study between 2006 and 2011. All patients had a delayed presentation of scaphoid fracture, and none of them was treated conservatively elsewhere. Patients with bone graft, sclerotic bone debridement, or displacement of the fragment at the nonunion site were excluded. A percutaneous transtrapezial fixation technique was used in all cases. Patients were reviewed until clinical and radiographic union was observed. At the final follow-up, DASH (Disabilities of the Arm, Shoulder and Hand) and PRWHE (Patient-Rated Wrist and Hand Evaluation) outcome scores were completed. Results Radiographic union was obtained in 15 out of 16 patients (94%) at an average follow-up of 36 months (range: 12-98 months). No complications from the percutaneous technique were noted. The average DASH score was 6 (range: 0-39) and the average PRWHE score was 10 (range: 0-56). No statistical significant difference in range of motion and grip strength was found between the operated side and the contralateral side. Conclusion Percutaneous transtrapezial screw fixation for delayed or nonunion of selected scaphoid fractures without bone grafting is promising. At a mean of 4 months, 94% union was obtained with good functional results when there was no sclerosis, minimal osteolysis, and no displacement at the scaphoid nonunion site. Type of Study Therapeutic study. Level of Evidence IV.
RESUMEN
BACKGROUND: Most total knee arthroplasty systems allow a degree of femoro-tibial component size mismatch. We aim to investigate the influence of size mismatch on outcome after primary total knee arthroplasty. METHODS: We reviewed 332 patients with cruciate-retaining Genesis II total knee arthroplasty with regard to femoro-tibial component size mismatch and Oxford Knee Score (OKS). We evaluated effects of Body Mass Index, gender and patellar procedure. Minimum follow-up is five years. We divided patients into four groups (tibial component larger than femoral component, no mismatch, femoral component one size larger and femoral component two sizes larger than tibial component). RESULTS: There was no statistically significant difference in OKS between the four groups. Size mismatch did not have a statistical significant effect on OKS in a multivariate analysis. Women had mismatched components in 66% of all cases and men in 40% of all cases. CONCLUSIONS: Our study showed no statistically significant effect of femoro-tibial size mismatch on outcome after total knee replacement. Compared to men, women tend to have more component size mismatch. LEVEL OF EVIDENCE: Level III, retrospective comparative study.
Asunto(s)
Artroplastia de Reemplazo de Rodilla/instrumentación , Fémur/cirugía , Artropatías/cirugía , Articulación de la Rodilla/cirugía , Prótesis de la Rodilla , Tibia/cirugía , Anciano , Anciano de 80 o más Años , Femenino , Humanos , Masculino , Persona de Mediana Edad , Estudios Retrospectivos , Factores SexualesRESUMEN
BACKGROUND: State-of-the-art treatment for Chiari Malformation I (CM-I) consists of decompression by posterior fossa craniectomy. A rare but severe complication that develops over months to years after this procedure is cerebellar slump. Treatment options for this condition are limited. We present a new and promising approach to treat this rare condition. METHODS: The patients were placed in the Trendelenburg position to facilitate ascent of the cerebellum. After almost complete dissolution of neurologic symptoms, surgical reconstruction was performed by tonsillar resection and the creation of a new structural support using a bone graft. RESULTS: Both patients experienced good clinical and morphological outcomes immediately after surgery, and for two years thereafter. CONCLUSIONS: Neurological symptoms related to cerebellar or brainstem slump can be adequately reversed by placing the patient in the Trendelenburg position. After uneventful gravitational reversal of the slump, safe surgical reconstruction of the cerebellar support can be performed to securely preserve the anatomical reversal.
Asunto(s)
Malformación de Arnold-Chiari/cirugía , Cerebelo/cirugía , Fosa Craneal Posterior/cirugía , Duramadre/cirugía , Siringomielia/cirugía , Adulto , Malformación de Arnold-Chiari/diagnóstico , Craneotomía/métodos , Descompresión Quirúrgica/métodos , Humanos , Masculino , Procedimientos de Cirugía Plástica , Siringomielia/diagnósticoRESUMEN
BACKGROUND: The aim of this study was to assess the influence of 3-dimensional (3D) preoperative planning and patient-specific instrument (PSI) guidance of glenoid component positioning on its inclination in total shoulder arthroplasty (TSA) and reverse shoulder arthroplasty (RSA). MATERIALS AND METHODS: Thirty-six shoulder arthroplasties (12 TSAs, 24 RSAs) were analyzed, of which 18 procedures (6 TSAs, 12 RSAs) were executed using preoperative 3D planning and patient-specific guides to position the central guide pin for glenoid component implantation. In 9 cases, the glenoid anatomy was severely distorted through wear or previous surgery. The inclination of the glenoid component was measured by 2 observers, using the angle between the glenoid baseplate and the floor of the supraspinatus fossa (angle ß) on postoperative radiographs. RESULTS: For TSA, the average angle ß was 74 ± 9 in the PSI group and 86 ± 12 in the non-PSI group; for RSA, the average angle ß was 83 ± 7 in the PSI group and 90 ± 17 in the non-PSI group. Extreme angles ß, which represent extreme values of glenoid component inclination, are more likely to occur in the non-PSI group than in the PSI group (P < .001 for TSA; P = .02 for RSA). CONCLUSIONS: The3D preoperative surgical planning and PSI guidance reduce variability in glenoid component inclination and avoid extreme inclination errors for TSA and RSA.
Asunto(s)
Artroplastia de Reemplazo/instrumentación , Cavidad Glenoidea/diagnóstico por imagen , Cavidad Glenoidea/cirugía , Cuidados Intraoperatorios/instrumentación , Articulación del Hombro/diagnóstico por imagen , Articulación del Hombro/cirugía , Anciano , Artroplastia de Reemplazo/métodos , Estudios de Casos y Controles , Femenino , Humanos , Imagenología Tridimensional , Masculino , Cuidados Preoperatorios , RadiografíaRESUMEN
BACKGROUND: Only a few articles describe the reproducibility and clinical feasibility of glenoid inclination measurements on conventional radiographs, and none of them validated their method in shoulder arthroplasty cases. From a clinical point of view, the angle measured between the supraspinatus fossa and the glenoid fossa line (angle ß) appears to be the most interesting angle to assess glenoid inclination. This study aimed to validate the angle ß in shoulder arthroplasty patients to facilitate the assessment of glenoid component inclination. MATERIALS AND METHODS: Seventeen patients who underwent total or reverse shoulder arthroplasty were evaluated. The angle ß was measured by 2 independent observers on postoperative radiographs and 3-dimensional (3D) models. The interobserver variability and accuracy of angle ß were analyzed by calculating the intraclass correlation coefficient (ICC) and by generating Bland-Altman plots. RESULTS: The angle ß showed a good interobserver variability (ICC = 0.971 for radiographs, ICC = 0.980 for 3D models) and a good agreement between the radiographic and 3D measurements (ICC = 0.904 for observer 1 and ICC = 0.908 for observer 2). Bland-Altman plots demonstrated that in 95% of the measurements on radiographs, the error will be <10. In the investigated population, 85% showed an error <6. CONCLUSION: This study demonstrates that angle ß can be measured on radiographs to assess glenoid component inclination in total and reverse shoulder arthroplasty, but clinicians and researchers should keep in mind that measurement errors of 10° may occur in a minority of cases.
Asunto(s)
Artroplastia de Reemplazo , Cavidad Glenoidea/diagnóstico por imagen , Prótesis Articulares , Articulación del Hombro/diagnóstico por imagen , Anciano , Artroplastia de Reemplazo/métodos , Simulación por Computador , Femenino , Humanos , Imagenología Tridimensional , Masculino , Persona de Mediana Edad , Variaciones Dependientes del Observador , Reproducibilidad de los Resultados , Articulación del Hombro/cirugía , Tomografía Computarizada por Rayos XRESUMEN
BACKGROUND: Trochlear dysplasia appears in different geometrical variations. The Dejour classification is widely used to grade the severity of trochlear dysplasia and to decide on treatment. PURPOSE: To investigate the effect of trochlear dysplasia on patellofemoral biomechanics and to determine if different types of trochlear dysplasia have different effects on patellofemoral biomechanics. STUDY DESIGN: Controlled laboratory study. METHODS: Trochlear dysplasia was simulated in 4 cadaveric knees by replacing the native cadaveric trochlea with different types of custom-made trochlear implants, manufactured with 3-dimensional printing. For each knee, 5 trochlear implants were designed: 1 implant simulated the native trochlea (control condition), and 4 implants simulated 4 types of trochlear dysplasia. The knees were subjected to 3 biomechanical tests: a squat simulation, an open chain extension simulation, and a patellar stability test. The patellofemoral kinematics, contact area, contact pressure, and stability were compared between the control condition (replica implants) and the trochlear dysplastic condition and among the subgroups of trochlear dysplasia. RESULTS: The patellofemoral joint in the trochlear dysplastic group showed increased internal rotation, lateral tilt, and lateral translation; increased contact pressures; decreased contact areas; and decreased stability when compared with the control group. Within the trochlear dysplastic group, the implants graded as Dejour type D showed the largest deviations for the kinematical parameters, and the implants graded as Dejour types B and D showed the largest deviations for the patellofemoral contact areas and pressures. CONCLUSION: Patellofemoral kinematics, contact area, contact pressure, and stability are significantly affected by trochlear dysplasia. Of all types of trochlear dysplasia, the models characterized with a pronounced trochlear bump showed the largest deviations in patellofemoral biomechanics. CLINICAL RELEVANCE: Investigating the relationship between the shape of the trochlea and patellofemoral biomechanics can provide insight into the short-term effects (maltracking, increased pressures, and instability) and long-term effects (osteoarthritis) of different types of trochlear dysplasia. Furthermore, this investigation provides an empirical explanation for better treatment outcomes of trochleoplasty for Dejour types B and D dysplasia.