Model-Based Design to Enhance Neotissue Formation in Additively Manufactured Calcium-Phosphate-Based Scaffolds.

In biomaterial-based bone tissue engineering, optimizing scaffold structure and composition remains an active field of research. Additive manufacturing has enabled the production of custom designs in a variety of materials. This study aims to improve the design of calcium-phosphate-based additively manufactured scaffolds, the material of choice in oral bone regeneration, by using a combination of in silico and in vitro tools. Computer models are increasingly used to assist in design optimization by providing a rational way of merging different requirements into a single design. The starting point for this study was an in-house developed in silico model describing the in vitro formation of neotissue, i.e., cells and the extracellular matrix they produced. The level set method was applied to simulate the interface between the neotissue and the void space inside the scaffold pores. In order to calibrate the model, a custom disk-shaped scaffold was produced with prismatic canals of different geometries (circle, hexagon, square, triangle) and inner diameters (0.5 mm, 0.7 mm, 1 mm, 2 mm). The disks were produced with three biomaterials (hydroxyapatite, tricalcium phosphate, and a blend of both). After seeding with skeletal progenitor cells and a cell culture for up to 21 days, the extent of neotissue growth in the disks' canals was analyzed using fluorescence microscopy. The results clearly demonstrated that in the presence of calcium-phosphate-based materials, the curvature-based growth principle was maintained. Bayesian optimization was used to determine the model parameters for the different biomaterials used. Subsequently, the calibrated model was used to predict neotissue growth in a 3D gyroid structure. The predicted results were in line with the experimentally obtained ones, demonstrating the potential of the calibrated model to be used as a tool in the design and optimization of 3D-printed calcium-phosphate-based biomaterials for bone regeneration.

Microarchitecture of titanium cylinders obtained by additive manufacturing does not influence osseointegration in the sheep.

Large bone defects are a challenge for orthopedic surgery. Natural (bone grafts) and synthetic biomaterials have been proposed but several problems arise such as biomechanical resistance or viral/bacterial safety. The use of metallic foams could be a solution to improve mechanical resistance and promote osseointegration of large porous metal devices. Titanium cylinders have been prepared by additive manufacturing (3D printing/rapid prototyping) with a geometric or trabecular microarchitecture. They were implanted in the femoral condyles of aged ewes; the animals were left in stabling for 90 and 270 days. A double calcein labeling was done before sacrifice; bones were analyzed by histomorphometry. Neither bone volume, bone/titanium interface nor mineralization rate were influenced by the cylinder's microarchitecture; the morphometric parameters did not significantly increase over time. Bone anchoring occurred on the margins of the cylinders and some trabeculae extended in the core of the cylinders but the amount of bone inside the cylinders remained low. The rigid titanium cylinders preserved bone cells from strains in the core of the cylinders. Additive manufacturing is an interesting tool to prepare 3D metallic scaffolds, but microarchitecture does not seem as crucial as expected and anchoring seems limited to the first millimeters of the graft.

In vitro and in vivo biocompatibility of calcium-phosphate scaffolds three-dimensional printed by stereolithography for bone regeneration.

Stereolithography (SLA) is an interesting manufacturing technology to overcome limitations of commercially available particulated biomaterials dedicated to intra-oral bone regeneration applications. The purpose of this study was to evaluate the in vitro and in vivo biocompatibility and osteoinductive properties of two calcium-phosphate (CaP)-based scaffolds manufactured by SLA three-dimensional (3D) printing. Pellets and macro-porous scaffolds were manufactured in pure hydroxyapatite (HA) and in biphasic CaP (HA:60-TCP:40). Physico-chemical characterization was performed using micro X-ray fluorescence, scanning electron microscopy (SEM), optical interferometry, and microtomography (µCT) analyses. Osteoblast-like MG-63 cells were used to evaluate the biocompatibility of the pellets in vitro with MTS assay and the cell morphology and growth characterized by SEM and DAPI-actin staining showed similar early behavior. For in vivo biocompatibility, newly formed bone and biodegradability of the experimental scaffolds were evaluated in a subperiosteal cranial rat model using µCT and descriptive histology. The histological analysis has not indicated evidences of inflammation but highlighted close contacts between newly formed bone and the experimental biomaterials revealing an excellent scaffold osseointegration. This study emphasizes the relevance of SLA 3D printing of CaP-based biomaterials for intra-oral bone regeneration even if manufacturing accuracy has to be improved and further experiments using biomimetic scaffolds should be conducted.