Performance Evaluation of an EI&CI Dual Ionization TOFMS Hyphenated with a Flow Modulated GC×GC System.

The use and compatibility of a dual-ionization TOFMS operating an EI source and a CI source in parallel using a single TOF mass analyzer with flow modulated two-dimensional GC (GC×GC) is described. Important figures of merit of the mass spectrometer that are required for two-dimensional GC hyphenation such as acquisition speed, ion source response, EI/CI switching, the GC transfer, and data alignment are carefully investigated and addressed. Improved fast switching ion optics allow switching in a 100 Hz frequency between EI and CI spectra sampled from the same GC×GC effluent. The spectra quality also influenced by the preseparation, especially of the EI source, is compared to a standard setup operating a single quadrupole MS coupled to the same GC system. Further, two setups including and excluding an additional flame ionization detector are presented. High increments in CI sensitivities are achieved by utilizing the high pumping efficiencies of the CI stage of the used mass spectrometer. By leading high flow ratios of the GC×GC modulation flows toward the CI source, the intensity can be increased by factors of up to 37 while maintaining the pressure balance of the less robust EI source. Finally, thermal desorption GC×GC-EI&CI-TOFMS analyses of traffic emission samples from a federal highway in Germany are executed with the presented setup.

Evaluation of GC-EI&CI-TOFMS for Nontarget Analysis of Industrial Wastewater Using Hydrophilic-Lipophilic-Balanced SPME.

The evaluation of nontarget analysis (NTA) techniques for the monitoring of wastewater is important as wastewater is an anthropogenic pollution source for aquatic ecosystems and a threat to human and environmental health. This study presents the proof-of-concept NTA of industrial wastewater samples. A prototype hydrophilic-lipophilic-balanced (HLB) SPME and gas chromatography interfaced with time-of-flight high-resolution mass spectrometry (GC-TOFMS) with electron ionization (EI) and chemical ionization (CI) in parallel are employed. The HLB-SPME consists of a poly(divinylbenzene-co-N-vinylpyrrolidone) structure, allowing the extraction of hydrophilic as well as lipophilic substances. As the combination of parallel CI and EI data provides a comprehensive data set as a unique feature, this study is strongly focused on the compound identification procedure and confidence reporting of exemplary substances. Furthermore, the use of three different CI reagent ions, including [N2H]+/[N4H]+, [H3O]+, and [NH4]+, enables a broad range of analytes to be ionized in terms of selectivity and softness. The complementary information provided by EI and CI data allows a level 3 identification or higher in 69% of cases. The polarity coverage based on the physicochemical properties of the analytes (such as volatility, water solubility, hydrophilicity, and lipophilicity) was visualized by using Henry's law and octanol-water partitioning constants. In conclusion, the presented approach is shown to be valuable for water analysis and allows enhanced and accelerated compound identification compared to utilizing only one type of ionization.

Gas chromatography coupled to time-of-flight mass spectrometry using parallel electron and chemical ionization with permeation tube facilitated reagent ion control for material emission analysis.

RATIONALE: Volatile organic compounds (VOCs) emitted by an artificial leather part for car interiors are determined using GC-MS (gas chromatograph coupled to a mass spectrometer) using simultaneous electron and chemical ionization (EI&CI). A device for swift reagent ion switching in CI mode between consecutive runs is presented. METHODS: VOCs emitted from the investigated material were sampled onto Tenax® absorption tubes using micro emission chambers and subsequently injected into the GC through thermal desorption. The detector was a time-of-flight mass spectrometer (TOFMS) simultaneously operating in EI and CI modes during a single chromatographic run. A custom permeation tube setup allowed for swift selection between various reagent ions in CI mode, e.g., [N2 H]+ , [H3 O]+ , [(H2 O)2 H]+ , and [NH4 ]+ . RESULTS: Different reagent ions are swiftly selectable between single GC runs without hardware changes. Differences in precursor ion survival yields and the selectivity of the various reactants were carefully assessed. Several examples for the improved identification of unknown compounds with the available complementary and comprehensive EI&CI data set are demonstrated for a relevant material emission application. CONCLUSION: The presented technique provides additional value to the standard GC-EI/MS procedure commonly used for material emission characterization. It allows for a non-targeted analysis approach with moderate analysis time.

Evaluating residual compressive strength of post-fire concrete using Raman Spectroscopy.

Cement and water within the concrete mass create a hydrated phase which acts as the glue for holding the sand and coarse aggregates in place to develop a strong construction material. The most important phase within the cement matrix is that of calcium silicate hydrate (CSH), which is largely responsible for the concrete strength. Decomposition of the CSH phase due to high temperatures will affect compressive strength of the concrete. Raman bands at 1083, 709 and 276 cm-1, which are representative of the CaCO3 and CSH presence in the concrete matrix phases can be used to assess changes in compressive strength as a result of thermal decomposition. The ratio between 1083/709 cm-1 bands was calculated and correlated to the compression strength of the concrete. The results show there is a rapid decline in strength around a critical peak ratio of 8.78 and a residual compressive strength of 0.62, closely following a polynomial curve. The tool developed here allows an indirect evaluation of the temperature the concrete has been exposed to by studying the band. A case study from a fire scene taken from a warehouse in Kingston (Jamaica) is also presented with the conclusion and results compared. The study showed that Raman spectroscopy has the potential to provide in-situ non-destructive testing of fire damaged concrete rapidly and accurately.