RESUMEN
Despite attractive cost-effectiveness, scalability, and superior stability, carbon-based printable perovskite solar cells (CPSCs) still face moisture-induced degradation that limits their lifespan and commercial potential. Here, the moisture-preventing mechanisms of thin nanostructured super-repellent coating (advancing contact angle >167° and contact angle hysteresis 7°) integrated into CPSCs are investigated for different moisture forms (falling water droplets vs water vapor vs condensed water droplets). It is shown that unencapsulated super-repellent CPSCs have superior performance under continuous droplet impact for 12 h (rain falling experiments) compared to unencapsulated pristine (uncoated) CPSCs that degrade within seconds. Contrary to falling water droplets, where super-repellent coating serves as a shield, water vapor is found to physisorb through porous super-repellent coating (room temperature and relative humidity, RH 65% and 85%) that increase the CPSCs performance for 21% during ≈43 d similarly to pristine CPSCs. It is further shown that water condensation forms within or below the super-repellent coating (40 °C and RH 85%), followed by chemisorption and degradation of CPSCs. Because different forms of water have distinct effects on CPSC, it is suggested that future standard tests for repellent CPSCs should include rain falling and condensate formation tests. The findings will thus inspire the development of super-repellent coatings for moisture prevention.
RESUMEN
Superhydrophobic surfaces are often seen as frictionless materials, on which water is highly mobile. Understanding the nature of friction for such water-repellent systems is central to further minimize resistance to motion and energy loss in applications. For slowly moving drops, contact-line friction has been generally considered dominant on slippery superhydrophobic surfaces. Here, we show that this general rule applies only at very low speed. Using a micropipette force sensor in an oscillating mode, we measure the friction of water drops approaching or even equaling zero contact-line friction. We evidence that dissipation then mainly stems from the viscous shearing of the air film (plastron) trapped under the liquid. Because this force is velocity dependent, it can become a serious drag on surfaces that look highly slippery from quasi-static tests. The plastron thickness is found to be the key parameter that enables the control of this special friction, which is useful information for designing the next generation of ultraslippery water-repellent coatings.
RESUMEN
The rapid development of 3D printing (or additive manufacturing) technologies demands new materials with novel properties and functionalities. Superhydrophobic materials, owing to their ultralow water adhesion, self-cleaning, anti-biofouling, or superoleophilic properties are useful for myriad applications involving liquids. However, the majority of the methods for making superhydrophobic surfaces have been based on surface functionalization and coatings, which are challenging to apply to 3D objects. Additionally, these coatings are vulnerable to abrasion due to low mechanical stability and limited thickness. Here, a new materials concept and methodology for 3D printing of superhydrophobic macroscopic objects with bulk nanostructure and almost unlimited geometrical freedom is presented. The method is based on a specific ink composed of hydrophobic (meth)acrylate monomers and porogen solvents, which undergoes phase separation upon photopolymerization to generate inherently nanoporous and superhydrophobic structures. Using a desktop Digital Light Processing printer, superhydrophobic 3D objects with complex shapes are demonstrated, with ultralow and uniform water adhesion measured with scanning droplet adhesion microscopy. It is shown that the 3D-printed objects, owing to their nanoporous structure throughout the entire volume, preserve their superhydrophobicity upon wear damage. Finally, a superhydrophobic 3D-printed gas-permeable and water-repellent microfluidic device and a hierarchically structured 3D-printed super-oil-absorbent are demonstrated.
RESUMEN
Superhydrophobic coatings have extraordinary properties like self-cleaning and staying dry, and have recently appeared on industrial and consumer markets. The stochastic nature of the coating components and coating processes (e.g., spraying, painting) affects the uniformity of the water repellency across the coated substrate. The wetting properties of those coatings are typically quantified on macroscale using contact angle goniometry (CAG). Here, highly sensitive force-based methods, scanning droplet adhesion microscopy (SDAM), and micropipette force sensor (MFS), are used, to quantify the microscale heterogeneity in the wetting properties of stochastic superhydrophobic coatings with irregular surface topography that cannot be investigated by CAG. By mapping the wetting adhesion forces with SDAM and friction forces with MFS, it is demonstrated that even the best coatings on the market are prone to heterogeneities that induce stick-slip motion of droplets. Thus, owing to their high spatial and force resolution, the advantages of these techniques over CAG are demonstrated.
RESUMEN
It is well known that an increased viscosity slows down fluid dynamics. Here we show that this intuitive rule is not general and can fail for liquids flowing in confined liquid-repellent systems. A gravity-driven, highly viscous glycerol droplet inside a sealed superhydrophobic capillary is moving more than 10 times faster than a water droplet with three-orders-of-magnitude lower viscosity. Using tracer particles, we show that the low-viscosity droplets are rapidly rotating internally, with flow velocities greatly exceeding the center-of-mass velocity. This is in stark contrast to the faster moving high-viscosity droplets with nearly vanishing internal flows. The anomalous viscosity-enhanced flow is caused by a viscosity-suppressed deformation of the droplet-air interface and a hydro- and aerodynamic coupling between the droplet and the air trapped within the micro/nanostructures (plastron). Our work demonstrates the unexpected role of the plastron in controlling fluid flow beyond the mere reduction in contact area and friction.
RESUMEN
The most widely used method to quantify the wetting properties of surfaces is by measuring contact angles. Even though contact angle goniometry is a powerful technique for characterizing wetting properties, it is not accurate for very hydrophobic surfaces. As the technique relies on image processing, it has inherent errors due to optical limitations, especially near the three-phase contact line. This leads to uncertainties in the positioning of the baseline, which can cause large errors in the measured contact angles. In this paper, we systematically evaluate these errors both theoretically and experimentally, focusing on the importance of image resolution. For â¼9 microliter droplet, displacement of the baseline by a single pixel leads to errors of approximately ±0.5° to ±1° for contact angles up to 150°, and errors increase rapidly in the superhydrophobic regime, up to ±8°. The error in the contact angle can be slightly reduced by increasing the image resolution, but cannot be eliminated entirely.
RESUMEN
The original version of this Article contained an error in Fig. 2b. The y-axis label in Fig. 2b was incorrectly labelled 'Snap-in force (µN)'. In the correct version, the axis is labelled 'Snap-in force (nN)'. In the original version of this Article, the "Butterfly wings" section of the Methods incorrectly stated the name of the butterfly as 'Golden bird'. In the correct version, the name of the butterfly is 'Golden birdwing'. These have now been corrected in both the PDF and HTML versions of the article.
RESUMEN
Droplets slip and bounce on superhydrophobic surfaces, enabling remarkable functions in biology and technology. These surfaces often contain microscopic irregularities in surface texture and chemical composition, which may affect or even govern macroscopic wetting phenomena. However, effective ways to quantify and map microscopic variations of wettability are still missing, because existing contact angle and force-based methods lack sensitivity and spatial resolution. Here, we introduce wetting maps that visualize local variations in wetting through droplet adhesion forces, which correlate with wettability. We develop scanning droplet adhesion microscopy, a technique to obtain wetting maps with spatial resolution down to 10 µm and three orders of magnitude better force sensitivity than current tensiometers. The microscope allows characterization of challenging non-flat surfaces, like the butterfly wing, previously difficult to characterize by contact angle method due to obscured view. Furthermore, the technique reveals wetting heterogeneity of micropillared model surfaces previously assumed to be uniform.
RESUMEN
The damped oscillations of liquid-immersed ferrofluid sessile droplets were studied with high-speed imaging experiments and analytical modeling to develop a novel microrheology technique. Droplet oscillations were induced with an external magnetic field, thereby avoiding transients in the resulting vibrational response of the droplet. By following the droplet relaxation with a high-speed camera, the frequency and relaxation time of the damped harmonic oscillations were measured. We extend upon existing analytical theories to describe our liquid-immersed sessile droplet system, and directly quantify the droplet relaxation with the viscosity of the internal and external fluid as well as the interfacial tension between these. The easily controllable magnetic droplets make our oscillating ferrofluid droplet technique a potential candidate for high-throughput microrheology and tensiometry in the future.