Accuracy, reproducibility, and uncertainty analysis of thyroid-probe-based activity measurements for determination of dose calibrator settings.

PURPOSE: In the nuclear medicine department, the activity of radiopharmaceuticals is measured using dose calibrators (DCs) prior to patient injection. The DC consists of an ionization chamber that measures current generated by ionizing radiation (emitted from the radiotracer). In order to obtain an activity reading, the current is converted into units of activity by applying an appropriate calibration factor (also referred to as DC dial setting). Accurate determination of DC dial settings is crucial to ensure that patients receive the appropriate dose in diagnostic scans or radionuclide therapies. The goals of this study were (1) to describe a practical method to experimentally determine dose calibrator settings using a thyroid-probe (TP) and (2) to investigate the accuracy, reproducibility, and uncertainties of the method. As an illustration, the TP method was applied to determine 188Re dial settings for two dose calibrator models: Atomlab 100plus and Capintec CRC-55tR. METHODS: Using the TP to determine dose calibrator settings involved three measurements. First, the energy-dependent efficiency of the TP was determined from energy spectra measurements of two calibration sources (152Eu and 22Na). Second, the gamma emissions from the investigated isotope (188Re) were measured using the TP and its activity was determined using γ-ray spectroscopy methods. Ambient background, scatter, and source-geometry corrections were applied during the efficiency and activity determination steps. Third, the TP-based 188Re activity was used to determine the dose calibrator settings following the calibration curve method [B. E. Zimmerman et al., J. Nucl. Med. 40, 1508-1516 (1999)]. The interobserver reproducibility of TP measurements was determined by the coefficient of variation (COV) and uncertainties associated to each step of the measuring process were estimated. The accuracy of activity measurements using the proposed method was evaluated by comparing the TP activity estimates of 99mTc, 188Re, 131I, and 57Co samples to high purity Ge (HPGe) γ-ray spectroscopy measurements. RESULTS: The experimental 188Re dial settings determined with the TP were 76.5 ± 4.8 and 646 ± 43 for Atomlab 100plus and Capintec CRC-55tR, respectively. In the case of Atomlab 100plus, the TP-based dial settings improved the accuracy of 188Re activity measurements (confirmed by HPGe measurements) as compared to manufacturer-recommended settings. For Capintec CRC-55tR, the TP-based settings were in agreement with previous results [B. E. Zimmerman et al., J. Nucl. Med. 40, 1508-1516 (1999)] which demonstrated that manufacturer-recommended settings overestimate 188Re activity by more than 20%. The largest source of uncertainty in the experimentally determined dial settings was due to the application of a geometry correction factor, followed by the uncertainty of the scatter-corrected photopeak counts and the uncertainty of the TP efficiency calibration experiment. When using the most intense photopeak of the sample's emissions, the TP method yielded accurate (within 5% errors) and reproducible (COV = 2%) measurements of sample's activity. The relative uncertainties associated with such measurements ranged from 6% to 8% (expanded uncertainty at 95% confidence interval, k = 2). CONCLUSIONS: Accurate determination/verification of dose calibrator dial settings can be performed using a thyroid-probe in the nuclear medicine department.

Cross-linked polyethylene glycol beads to separate 99mTc-pertechnetate from low-specific-activity molybdenum.

UNLABELLED: We report a kit-based approach for the purification of sodium pertechnetate ((99m)TcO4 (-)) from solutions with high MoO4 (2-) content. METHODS: Cross-linked polyethylene glycol resins (ChemMatrix) were used to separate (99m)Tc and molybdenum in 4N NaOH. The resins were loaded at various flow rates and eluted with water to release (99m)Tc. The (99m)Tc solution was passed through a cation exchange resin and an alumina cartridge, followed by saline elution. This process was tested with cyclotron-produced (99m)Tc using an automated system and disposable kits. RESULTS: Optimal results were obtained by loading 500 mg of resin at flow rates of up to 3.1 mL/min, with quantitative extraction of (99m)Tc from the molybdate solution and complete release of (99m)Tc after elution with water. The automated system was highly efficient at isolating Na(99m)TcO4 within minutes, with a recovery rate of 92.7% ± 1.1% (mean ± SD) using cyclotron-produced (99m)Tc. CONCLUSION: ChemMatrix resins were highly effective at separating (99m)TcO4 (-) from molybdate solutions.

Implementation of Multi-Curie Production of (99m)Tc by Conventional Medical Cyclotrons.

UNLABELLED: (99m)Tc is currently produced by an aging fleet of nuclear reactors, which require enriched uranium and generate nuclear waste. We report the development of a comprehensive solution to produce (99m)Tc in sufficient quantities to supply a large urban area using a single medical cyclotron. METHODS: A new target system was designed for (99m)Tc production. Target plates made of tantalum were coated with a layer of (100)Mo by electrophoretic deposition followed by high-temperature sintering. The targets were irradiated with 18-MeV protons for up to 6 h, using a medical cyclotron. The targets were automatically retrieved and dissolved in 30% H2O2. (99m)Tc was purified by solid-phase extraction or biphasic exchange chromatography. RESULTS: Between 1.04 and 1.5 g of (100)Mo were deposited on the tantalum plates. After high-temperature sintering, the (100)Mo formed a hard, adherent layer that bonded well with the backing surface. The targets were irradiated for 1-6.9 h at 20-240 µA of proton beam current, producing up to 348 GBq (9.4 Ci) of (99m)Tc. The resulting pertechnetate passed all standard quality control procedures and could be used to reconstitute typical anionic, cationic, and neutral technetium radiopharmaceutical kits. CONCLUSION: The direct production of (99m)Tc via proton bombardment of (100)Mo can be practically achieved in high yields using conventional medical cyclotrons. With some modifications of existing cyclotron infrastructure, this approach can be used to implement a decentralized medical isotope production model. This method eliminates the need for enriched uranium and the radioactive waste associated with the processing of uranium targets.