Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 20 de 331
Filtrar
1.
Adv Mater ; : e2405718, 2024 Jul 16.
Artículo en Inglés | MEDLINE | ID: mdl-39014920

RESUMEN

As-cast organic solar cells (OSCs) possess tremendous potential for low-cost commercial applications. Herein, five small-molecule acceptors (A1-A5) are designed and synthesized by selectively and elaborately extending the alkyl inner side chain flanking on the pyrrole motif to prepare efficient as-cast devices. As the extension of the alkyl chain, the absorption spectra of the films are gradually blue-shifted from A1 to A5 along with slightly uplifted lowest unoccupied molecular orbital energy levels, which is conducive for optimizing the trade-off between short-circuit current density and open-circuit voltage of the devices. Moreover, a longer alkyl chain improves compatibility between the acceptor and donor. The in situ technique clarifies that good compatibility will prolong molecular assembly time and assist in the preferential formation of the donor phase, where the acceptor precipitates in the framework formed by the donor. The corresponding film-formation dynamics facilitate the realization of favorable film morphology with a suitable fibrillar structure, molecular stacking, and vertical phase separation, resulting in an incremental fill factor from A1 to A5-based devices. Consequently, the A3-based as-cast OSCs achieve a top-ranked efficiency of 18.29%. This work proposes an ingenious strategy to manipulate intermolecular interactions and control the film-formation process for constructing high-performance as-cast devices.

2.
Small ; : e2404734, 2024 Jul 05.
Artículo en Inglés | MEDLINE | ID: mdl-38966904

RESUMEN

The morphology of the active layer is crucial for highly efficient organic solar cells (OSCs), which can be regulated by selecting a rational third component. In this work, the highly crystalline nonfullerene acceptor BTP-eC9 is selected as the morphology regulator in OSCs with PM6:BTP-BO-4Cl as the main system. The addition of BTP-eC9 can prolong the nucleation and crystallization progress of acceptor and donor molecules, thereby enhancing the order of molecular arrangement. Meanwhile, the nucleation and crystallization time of the donor is earlier than that of the acceptors after introducing BTP-eC9, which is beneficial for obtaining a better vertical structural phase separation. The exciton dissociation, charge transport, and charge collection are promoted effectively by the optimized morphology of the active layer, which improves the short-circuit current density and filling factor. After introducing BTP-eC9, the power conversion efficiencies (PCEs) of the ternary OSCs are improved from 17.31% to 18.15%. The PCE is further improved to 18.39% by introducing gold nanopyramid (Au NBPs) into the hole transport layer to improve photon utilization efficiency. This work indicates that the morphology can be optimized by selecting a highly crystalline third component to regulate the nucleation and crystallization progress of the acceptor and donor molecules.

3.
Angew Chem Int Ed Engl ; : e202408537, 2024 Jul 08.
Artículo en Inglés | MEDLINE | ID: mdl-38973771

RESUMEN

Achieving high electrical conductivity (σ) and power factor (PF) simultaneously remains a significant challenge for n-type organic themoelectrics (OTEs). Herein, we demonstrate the state-of-the-art OTEs performance through blending a fused bithiophene imide dimer-based polymer f-BTI2g-SVSCN and its selenophene-substituted analogue f-BSeI2g-SVSCN with a julolidine-functionalized benzimidazoline n-dopant JLBI, vis-à-vis when blended with commercially available n-dopants TAM and N-DMBI. The advantages of introducing a more lipophilic julolidine group into the dopant structure of JLBI are evidenced by the enhanced OTEs performance that JLBI-doped films show when compared to those doped with N-DMBI or TAM. In fact, thanks to the enhanced intermolecular interactions and the lower-lying LUMO level enabled by the increase of selenophene content in polymer backbone, JLBI-doped films of f-BSeI2g-SVSCN exhibit a unprecedent σ of 206 S cm-1 and a PF of 114 µW m-1 K-2. Interestingly, σ can be further enhanced up to 326 S cm-1 by using TAM dopant as a consequence of its favorable diffusion behavior into densely packed crystalline domains. These values are the highest to date for solution-processed molecularly n-doped polymers, demonstrating the effectiveness of the polymer-dopant matching approach carried out in this work.

4.
Adv Mater ; : e2404597, 2024 Jul 08.
Artículo en Inglés | MEDLINE | ID: mdl-38975985

RESUMEN

Photomultiplication (PM)-type organic photodetectors (OPDs), which typically form a homogeneous distribution (HD) of n-type dopants in a p-type polymer host (HD PM-type OPDs), have achieved a breakthrough in device responsivity by surpassing a theoretical limit of external quantum efficiency (EQE). However, they face limitations in higher dark current and slower dynamic characteristics compared to p-n heterojunction (p-n HJ) OPDs due to inherent long lifetime of trapped electrons. To overcome this, we have developed a new PM-type OPD that demonstrates ultrafast dynamic properties through a vertical phase separation (VPS) strategy between the p-type polymer (host) and n-type acceptor (dopant), referred to as VPS PM-type OPDs. Notably, VPS PM-type OPDs show a remarkable increase (by three orders of magnitude) in -3 dB cut-off frequency (120 kHz) and over a 200-fold faster response time (rising time = 4.8 µs, falling time = 8.3 µs) compared to HD PM-type OPDs, while maintaining high EQE of 1,121% and specific detectivity of 2.53 × 1013 Jones at -10 V. The VPS PM OPD represents a groundbreaking advancement by demonstrating the coexistence of p-n HJ and PM modes within a single photoactive layer for the first time. This innovative approach holds the potential to enhance both static and dynamic properties of OPDs. This article is protected by copyright. All rights reserved.

5.
ACS Appl Mater Interfaces ; 16(27): 35400-35409, 2024 Jul 10.
Artículo en Inglés | MEDLINE | ID: mdl-38917455

RESUMEN

A series of dual-band photomultiplication (PM)-type organic photodetectors (OPDs) were fabricated by employing a donor(s)/acceptor (100:1, wt/wt) mixed layer and an ultrathin Y6 layer as the active layers, as well as by using PNDIT-F3N as an interfacial layer near the indium tin oxide (ITO) electrode. The dual-band PM-type OPDs exhibit the response range of 330-650 nm under forward bias and the response range of 650-850 nm under reverse bias. The tunable spectral response range of dual-band PM-type OPDs under forward or reverse bias can be explained well from the trapped electron distribution near the electrodes. The dark current density (JD) of the dual-band PM-type OPDs can be efficiently suppressed by employing PNDIT-F3N as the anode interfacial layer and the special active layers with hole-only transport characteristics. The light current density (JL) of the dual-band PM-type OPDs can be slightly increased by incorporating wide-bandgap polymer P-TPDs with relatively large hole mobility (µh) in the active layers. The signal-to-noise ratios of the optimized dual-band PM-type OPDs reach 100,980 under -50 V bias and white light illumination with an intensity of 1.0 mW·cm-2, benefiting from the ultralow JD by employing wide-bandgap PNDIT-F3N as the anode interfacial buffer layer and the increased JL by incorporating appropriate P-TPD in the active layers.

6.
Artículo en Inglés | MEDLINE | ID: mdl-38890543

RESUMEN

BACKGROUND: Emerging studies suggest that endocrine disrupting chemicals (EDCs) in personal care and other consumer products are linked with various adverse health effects, including respiratory and reproductive effects. Despite Black persons using more personal care products than other demographic groups and having a high asthma burden, little is known regarding their consumer product use patterns and associated EDC exposures. OBJECTIVE: To examine the association between recent exposure to select EDCs with specific consumer products and behaviors in a cohort of 110 predominantly Black children with asthma, ages 8-17 years, living in Baltimore City, Maryland. METHODS: We quantified concentrations of bisphenol A (BPA), bisphenol S (BPS), bisphenol F, two dichlorophenols, four parabens, triclosan, benzophenone-3, and triclocarban in spot urine samples. Questionnaires were used to capture recent (last 24-h) consumer product use and behaviors. Associations between EDCs and consumer product uses/behaviors were assessed using multivariable linear regression, adjusting for age, gender, race/ethnicity, and caregiver income level. Effect estimates were expressed as geometric mean ratios of biomarker concentrations of product-users vs non-users. RESULTS: Increased concentrations to select EDCs were associated with recent use of air freshener (ratios; BPA: 1.9, 95%CI 1.4-2; BPS 1.7, 95%CI 1-2.97; propyl paraben: 3.0, 95%CI 1.6-5.6), scented candles (methyl paraben: 2.6, 95%CI 1.1-6.1), and scented carpet powder (2,5-dichlorophenol: 2.8, 95%CI 1.2-6.3). Additionally, consuming canned food was associated with some increased biomarker concentrations (ratios: BPA: 1.7, 95%CI 1.2-2.4; BPS: 2.1, 95% CI: 1.2-3.6). SIGNIFICANCE: These findings add to the body of evidence suggesting that recent use of select consumer products in Black children contributes to exposure of chemicals of concern and could potentially inform exposure mitigation interventions. Findings have broad potential health implications for pediatric populations and Black children who may face exposure and health disparities. IMPACT: Little is known about how children's personal care product use and consumer behaviors affect their exposures to endocrine disrupting chemicals (EDCs). This is particularly true for Black children who often experience a disparate exposure burden to many EDCs. This is a significant knowledge gap among children that are uniquely vulnerable to EDCs as they undergo critical windows of growth and development. Our findings show associations between consumer products and EDC exposures in predominantly Black children in low-income settings. Identifying EDC exposure determinants has broad health implications as many of these chemicals have been associated with adverse health risks.

7.
ACS Appl Mater Interfaces ; 16(26): 33885-33896, 2024 Jul 03.
Artículo en Inglés | MEDLINE | ID: mdl-38888910

RESUMEN

Donor (D)-acceptor (A) copolymer-based organic mixed ionic-electronic conductors (OMIECs) exhibit intrinsic environmental stability for they have tailored energy levels. However, their figure-of-merit (µC*) is still falling behind the D-D polymers because of morphology deterioration during the electrochemical doping process. Herein, we developed two D-A copolymers with precisely regulated backbone curvature, namely PTBT-P and PTTBT-P. Compared to the curved PTBT-P and previously reported copolymers, PTTBT-P better keeps its backbone linear, leading to a long-range ordered doping morphology, which is revealed by the in operando X-ray technique. This optimized doping morphology enables a significantly improved operando charge mobility (µ) of 2.44 cm2 V-1 s-1 and a µC* value of 342 F cm-1 V-1 s-1, one of the highest values in D-A copolymer based on OECTs. Besides, we fabricated PTTBT-P-based electrochemical random-access memories and achieved ideal and robust conductance modulation. This study highlights the critical role of backbone curvature control in the optimization of doping morphology for efficient and robust organic electrochemical devices.

8.
J Am Chem Soc ; 146(23): 15860-15868, 2024 Jun 12.
Artículo en Inglés | MEDLINE | ID: mdl-38814791

RESUMEN

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a benchmark hole-transporting (p-type) polymer that finds applications in diverse electronic devices. Most of its success is due to its facile synthesis in water, exceptional processability from aqueous solutions, and outstanding electrical performance in ambient. Applications in fields like (opto-)electronics, bioelectronics, and energy harvesting/storage devices often necessitate the complementary use of both p-type and n-type (electron-transporting) materials. However, the availability of n-type materials amenable to water-based polymerization and processing remains limited. Herein, we present a novel synthesis method enabling direct polymerization in water, yielding a highly conductive, water-processable n-type conjugated polymer, namely, poly[(2,2'-(2,5-dihydroxy-1,4-phenylene)diacetic acid)-stat-3,7-dihydrobenzo[1,2-b:4,5-b']difuran-2,6-dione] (PDADF), with remarkable electrical conductivity as high as 66 S cm-1, ranking among the highest for n-type polymers processed using green solvents. The new n-type polymer PDADF also exhibits outstanding stability, maintaining 90% of its initial conductivity after 146 days of storage in air. Our synthetic approach, along with the novel polymer it yields, promises significant advancements for the sustainable development of organic electronic materials and devices.

9.
Nature ; 630(8015): 96-101, 2024 Jun.
Artículo en Inglés | MEDLINE | ID: mdl-38750361

RESUMEN

Chemical doping is an important approach to manipulating charge-carrier concentration and transport in organic semiconductors (OSCs)1-3 and ultimately enhances device performance4-7. However, conventional doping strategies often rely on the use of highly reactive (strong) dopants8-10, which are consumed during the doping process. Achieving efficient doping with weak and/or widely accessible dopants under mild conditions remains a considerable challenge. Here, we report a previously undescribed concept for the photocatalytic doping of OSCs that uses air as a weak oxidant (p-dopant) and operates at room temperature. This is a general approach that can be applied to various OSCs and photocatalysts, yielding electrical conductivities that exceed 3,000 S cm-1. We also demonstrate the successful photocatalytic reduction (n-doping) and simultaneous p-doping and n-doping of OSCs in which the organic salt used to maintain charge neutrality is the only chemical consumed. Our photocatalytic doping method offers great potential for advancing OSC doping and developing next-generation organic electronic devices.

10.
Angew Chem Int Ed Engl ; : e202407273, 2024 May 21.
Artículo en Inglés | MEDLINE | ID: mdl-38770935

RESUMEN

A new approach to control the n-doping reaction of organic semiconductors is reported using surface-functionalized gold nanoparticles (f-AuNPs) with alkylthiols acting as the catalyst only upon mild thermal activation. To demonstrate the versatility of this methodology, the reaction of the n-type dopant precursor N-DMBI-H with several molecular and polymeric semiconductors at different temperatures with/without f-AuNPs, vis-à-vis the unfunctionalized catalyst AuNPs, was investigated by spectroscopic, morphological, charge transport, and kinetic measurements as well as, computationally, the thermodynamic of catalyst activation. The combined experimental and theoretical data demonstrate that while f-AuNPs is inactive at room temperature both in solution and in the solid state, catalyst activation occurs rapidly at mild temperatures (~70 °C) and the doping reaction completes in few seconds affording large electrical conductivities (~10-140 S cm-1). The implementation of this methodology enables the use of semiconductor+dopant+catalyst solutions and will broaden the use of the corresponding n-doped films in opto-electronic devices such as thin-film transistors, electrochemical transistors, solar cells, and thermoelectrics well as guide the design of new catalysts.

11.
Adv Sci (Weinh) ; : e2309786, 2024 May 17.
Artículo en Inglés | MEDLINE | ID: mdl-38760898

RESUMEN

A universal approach for enhancing water affinity in polymer photocatalysts by covalently attaching hydrophilic photocrosslinkers to polymer chains is presented. A series of bisdiazirine photocrosslinkers, each comprising bisdiazirine photophores linked by various aliphatic (CL-R) or ethylene glycol-based bridge chains (CL-TEG), is designed to prevent crosslinked polymer photocatalysts from degradation through a safe and efficient photocrosslinking reaction at a wavelength of 365 nm. When employing the hydrophilic CL-TEG as a photocrosslinker with polymer photocatalysts (F8BT), the hydrogen evolution reaction (HER) rate is considerably enhanced by 2.5-fold compared to that obtained using non-crosslinked F8BT photocatalysts, whereas CL-R-based photocatalysts yield HER rates comparable to those of non-crosslinked counterparts. Photophysical analyses including time-resolved photoluminescence and transient absorption measurements reveal that adding CL-TEG accelerates exciton separation, forming long-lived charge carriers. Additionally, the in-depth study using molecular dynamics simulations elucidates the dual role of CL-TEG: it enhances water penetration into the polymer matrix and stabilizes charge carriers after exciton generation against undesirable recombination. Therefore, the strategy highlights endowing a high-permittivity environment within polymer photocatalyst in a controlled manner is crucial for enhancing photocatalytic redox reactivity. Furthermore, this study shows that this hydrophilic crosslinker approach has a broad applicability in general polymer semiconductors and their nanoparticulate photocatalysts.

12.
Mater Horiz ; 11(12): 2926-2936, 2024 Jun 17.
Artículo en Inglés | MEDLINE | ID: mdl-38567487

RESUMEN

Recently, inverted perovskite solar cells (PeSCs) have witnessed significant advancements; however, their long-term stability remains a challenge because of the oxidation of silver cathodes to form AgI by mobile iodides. To overcome this problem, we propose the integration of an electron-deficient naphthalene diimide-based zwitterion (NDI-ZI) as the cathode interlayer. Compared to the physical ion-blocking layer, it effectively captures ions by forming ionic bonds via electrostatic Coulombic interaction to suppress the migration of iodide and Ag ions. The NDI-ZI interlayer also suppresses the shunt paths and modulates the work function of the Ag electrode by forming interface dipoles, thereby enhancing charge extraction. FA0.85Cs0.15PbI3 based PeSCs incorporating NDI-ZI exhibited a noticeably high power conversion efficiency of up to 23.3% and outstanding stability, maintaining ∼80% of their initial performance over 1500 h at 85 °C and over 500 h under continuous 1-sun illumination. This study highlights the potential of a zwitterionic cathode interlayer in diverse perovskite optoelectronic devices, leading to their improved efficiency and stability.

13.
Chronic Obstr Pulm Dis ; 11(3): 293-302, 2024 May 29.
Artículo en Inglés | MEDLINE | ID: mdl-38687147

RESUMEN

Background: Omega-3 polyunsaturated fatty acids (PUFAs) have been associated with systemic anti-inflammatory responses. Dietary intake of omega-3 PUFAs eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) has also been associated with lower chronic obstructive pulmonary disease (COPD) morbidity using self-report food frequency questionnaires. Objective: The objective of this study was to investigate the relationship between measured PUFA intake using plasma EPA+DHA levels and COPD morbidity. Methods: Former smokers with moderate-to-severe COPD living in low-income communities were enrolled in a 6-month prospective cohort study. Participants completed standardized questionnaires, spirometry, and plasma samples at 3-month intervals. Total plasma PUFAs were analyzed using gas chromatography/mass spectrometry for DHA and EPA concentrations. Linear or logistic mixed model regression was used to evaluate EPA+DHA's and COPD morbidity's association, accounting for demographics, lung function, pack years, comorbidities, and neighborhood poverty. Results: A total of 133 plasma EPA+DHA samples from 57 participants were available. Participants exhibited average plasma EPA and DHA levels of 14.7±7.3µg/mL and 40.2±17.2µg/mL, respectively, across the 3 clinic visits. Each standard deviation increase in EPA+DHA levels was associated with 2.7 points lower St George's Respiratory Questionnaire score (95% confidence interval [CI] -5.2, -0.2) and lower odds of moderate exacerbation (odds ratio 0.4; 95% CI 0.2, 0.9), but lacked significant association with the COPD Assessment Test score (95% CI -2.4, 0.8), modified Medical Research Council dyspnea scale (95% CI -02, 0.2), or severe exacerbations (95% CI 0.3, 1.4). Conclusion: Plasma EPA+DHA levels are associated with better respiratory-specific quality of life and lower odds of moderate exacerbations in patients with moderate-to-severe COPD. Further research is warranted to investigate the efficacy of an omega-3 dietary intervention in the management of COPD morbidities.

14.
Ann Am Thorac Soc ; 2024 Apr 03.
Artículo en Inglés | MEDLINE | ID: mdl-38568439

RESUMEN

RATIONALE: It is unknown whether air pollution is associated with radiographic features of interstitial lung disease in individuals with chronic obstructive pulmonary disease (COPD). OBJECTIVES: To determine whether air pollution increases prevalence of interstitial lung abnormalities (ILA) or percent high-attenuation area (HAA) on computed tomography (CT) in individuals with a heavy smoking history and COPD. METHODS: We performed a cross-sectional study of SPIROMICS (Subpopulations and Intermediate Outcome Measures in COPD Study), focused on current or former smokers with COPD. 10-year exposure to particulate matter < 2.5 µm (PM2.5), nitrogen oxides (NOx), nitrogen dioxide (NO2), and ozone (O3) prior to enrollment CTs (completed between 2010-2015) were estimated with validated spatiotemporal models at residential addresses. We applied adjusted multivariable modified Poisson regression and linear regression to investigate associations between pollution exposure and relative risk of ILA or increased percent HAA (between -600 and -250 Hounsfield units) respectively. We assessed for effect modification by MUC5B-promoter polymorphism (GT/TT vs GG at rs3705950), smoking status, sex, and percent emphysema. RESULTS: Among 1272 participants with COPD assessed for HAA, 424 were current smokers, 249 were carriers of the variant MUC5B allele (GT/TT). 519 participants were assessed for ILA. We found no association between pollution exposure and ILA or HAA. Associations between pollutant exposures and risk of ILA were modified by the presence of MUC5B polymorphism (p-value interaction term for NOx = 0.04 and PM2.5 = 0.05) and smoking status (p-value interaction term for NOx = 0.05, NO2 = 0.01, and O3 = 0.05). With higher exposure to NOx and PM2.5, MUC5B variant carriers had increased risk of ILA (Relative Risk [RR] per 26ppb NOx 2.41; 95% Confidence Interval [CI] 0.97 to 6.0) and RR per 4 µg·m-3 PM2.5 1.43; 95% CI 0.93 to 2.2). With higher exposure to NO2, former smokers had increased risk of ILA (RR per 10ppb 1.64; 95% CI 1.0 to 2.7). CONCLUSIONS: Exposure to ambient air pollution was not associated with interstitial features on CT in this population of heavy smokers with COPD. MUC5B modified the association between pollution and ILA, suggesting that gene-environment interactions may influence prevalence of interstitial lung features in COPD.

15.
Angew Chem Int Ed Engl ; 63(17): e202319627, 2024 Apr 22.
Artículo en Inglés | MEDLINE | ID: mdl-38443313

RESUMEN

High-performing n-type polymers are crucial for the advance of organic electronics field, however strong electron-deficient building blocks with optimized physicochemical properties for constructing them are still limited. The imide-functionalized polycyclic aromatic hydrocarbons (PAHs) with extended π-conjugated framework, high electron deficiency and good solubility serve as promising candidates for developing high-performance n-type polymers. Among the PAHs, phenanthrene (PhA) features a well-delocalized aromatic π-system with multiple modifiable active sites . However, the PhA-based imides are seldom studied, mainly attributed to the synthetic challenge. Herein, we report two functionalized PhAs, CPOI and CPCNI, by simultaneously incorporating imide with carbonyl or dicyanomethylene onto PhA. Notably, the dicyanomethylene-modified CPCNI exhibits a well stabilized LUMO energy level (-3.84 eV), attributed to the synergetic inductive effect from imide and cyano groups. Subsequently, based on CPOI and CPCNI, two polymers PCPOI-Tz and PCPCNI-Tz were developed. Applied to organic thin-film transistors, owing to the strong electron-deficiency of CPCNI, polymer PCPCNI-Tz shows an improved electron mobility and largely decreased threshold voltage compared with PCPOI-Tz. This work affords two structurally novel electron-deficient building blocks and highlights the effectiveness of dual functionalization of PhAs with strong electron-withdrawing groups for devising n-type polymers.

16.
Artículo en Inglés | MEDLINE | ID: mdl-38507607

RESUMEN

RATIONALE: Individuals with COPD have airflow obstruction and maldistribution of ventilation. For those living at high altitude, any gas exchange abnormality is compounded by reduced partial pressures of inspired oxygen. OBJECTIVES: Does residence at higher-altitude exposure affect COPD outcomes, including lung function, imaging characteristics, symptoms, health status, functional exercise capacity, exacerbations, or mortality? METHODS: From the SPIROMICS cohort, we identified individuals with COPD living below 1,000 ft (305 m) elevation (n= 1,367) versus above 4,000 ft (1,219 m) elevation (n= 288). Multivariable regression models were used to evaluate associations of exposure to high altitude with COPD-related outcomes. MEASUREMENTS AND MAIN RESULTS: Living at higher altitude was associated with reduced functional exercise capacity as defined by 6MWD (-32.3 m, (-55.7 to -28.6)). There were no differences in patient-reported outcomes as defined by symptoms (CAT, mMRC), or health status (SGRQ). Higher altitude was not associated with a different rate of FEV1 decline. Higher altitude was associated with lower odds of severe exacerbations (IRR 0.65, (0.46 to 0.90)). There were no differences in small airway disease, air trapping, or emphysema. In longitudinal analyses, higher altitude was associated with increased mortality (HR 1.25, (1.0 to 1.55)); however, this association was no longer significant when accounting for air pollution. CONCLUSIONS: Chronic altitude exposure is associated with reduced functional exercise capacity in individuals with COPD, but this did not translate into differences in symptoms or health status. Additionally, chronic high-altitude exposure did not affect progression of disease as defined by longitudinal changes in spirometry.

17.
ACS Appl Mater Interfaces ; 16(10): 12886-12896, 2024 Mar 13.
Artículo en Inglés | MEDLINE | ID: mdl-38425182

RESUMEN

Eco-friendly solution processing and the low-cost synthesis of photoactive materials are important requirements for the commercialization of organic solar cells (OSCs). Although varieties of aqueous-soluble acceptors have been developed, the availability of aqueous-processable polymer donors remains quite limited. In particular, the generally shallow highest occupied molecular orbital (HOMO) energy levels of existing polymer donors limit further increases in the power conversion efficiency (PCE). Here, we design and synthesize two water/alcohol-processable polymer donors, poly[(thiophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-T)) and poly[(selenophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-Se)) with oligo(ethylene glycol) (OEG) side chains, having deep HOMO energy levels (∼-5.4 eV). The synthesis of the polymers is achieved in a few synthetic and purification steps at reduced cost. The theoretical calculations uncover that the dielectric environmental variations are responsible for the observed band gap lowering in OEG-based polymers compared to their alkylated counterparts. Notably, the aqueous-processed all-polymer solar cells (aq-APSCs) based on P(Qx8O-T) and poly[(N,N'-bis(3-(2-(2-(2-methoxyethoxy)-ethoxy)ethoxy)-2-((2-(2-(2-methoxyethoxy)ethoxy)ethoxy)-methyl)propyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl)-alt-(2,5-thiophene)] (P(NDIDEG-T)) active layer exhibit a PCE of 2.27% and high open-circuit voltage (VOC) approaching 0.8 V, which are among the highest values for aq-APSCs reported to date. This study provides important clues for the design of low-cost, aqueous-processable polymer donors and the fabrication of aqueous-processable OSCs with high VOC.

18.
Small ; : e2401176, 2024 Mar 26.
Artículo en Inglés | MEDLINE | ID: mdl-38529741

RESUMEN

Incorporating a third component into binary organic solar cells (b-OSCs) has provided a potential platform to boost power conversion efficiency (PCEs). However, gaining control over the non-equilibrium blend morphology via the molecular design of the perylene diimide (PDI)-based third component toward efficient ternary organic solar cells (t-OSCs) still remains challenging. Herein, two novel PDI derivatives are developed with tailored molecular planarity, namely ufBTz-2PDI and fBTz-2PDI, as the third component for t-OSCs. Notably, after performing a cyclization reaction, the twisted ufBTz-2PDI with an amorphous character transferred to the highly planar fBTz-2PDI followed by a semi-crystalline character. When incorporating the semi-crystalline fBTz-2PDI into the D18:L8-BO system, the resultant t-OSC achieved an impressive PCE of 18.56%, surpassing the 17.88% attained in b-OSCs. In comparison, the addition of amorphous ufBTz-2PDI into the binary system facilitates additional charge trap sites and results in a deteriorative PCE of 14.37%. Additionally, The third component fBTz-2PDI possesses a good generality in optimizing the PCEs of several b-OSCs systems are demonstrated. The results not only provided a novel A-DA'D-A motif for further designing efficient third component but also demonstrated the crucial role of modulated crystallinity of the PDI-based third component in optimizing PCEs of t-OSCs.

19.
Trends Biotechnol ; 2024 Feb 23.
Artículo en Inglés | MEDLINE | ID: mdl-38402137

RESUMEN

Laboratory automation with robot-assisted processes enhances synthetic biology, but its economic impact on projects is uncertain. We have proposed an experiment price index (EPI) for a quantitative comparison of factors in time, cost, and sample numbers, helping measure the efficiency of laboratory automation in synthetic biology and biomolecular engineering.

20.
Adv Mater ; 36(18): e2308750, 2024 May.
Artículo en Inglés | MEDLINE | ID: mdl-38289228

RESUMEN

Semi-transparent organic solar cells (ST-OSCs) possess significant potential for applications in vehicles and buildings due to their distinctive visual transparency. Conventional device engineering strategies are typically used to optimize photon selection and utilization at the expense of power conversion efficiency (PCE); moreover, the fixed spectral utilization range always imposes an unsatisfactory upper limit to its light utilization efficiency (LUE). Herein, a novel solid additive named 1,3-diphenoxybenzene (DB) is employed to dual-regulate donor/acceptor molecular aggregation and crystallinity, which effectively broadens the spectral response of ST-OSCs in near-infrared region. Besides, more visible light is allowed to pass through the devices, which enables ST-OSCs to possess satisfactory photocurrent and high average visible transmittance (AVT) simultaneously. Consequently, the optimal ST-OSC based on PP2+DB/BTP-eC9+DB achieves a superior LUE of 4.77%, representing the highest value within AVT range of 40-50%, which also correlates with the formation of multi-scale phase-separated morphology. Such results indicate that the ST-OSCs can simultaneously meet the requirements for minimum commercial efficiency and plant photosynthesis when integrated with the roofs of agricultural greenhouses. This work emphasizes the significance of additives to tune the spectral response in ST-OSCs, and charts the way for organic photovoltaics in economically sustainable agricultural development.

SELECCIÓN DE REFERENCIAS
DETALLE DE LA BÚSQUEDA