The Rejuvenation Effect of Bio-Oils on Long-Term Aged Asphalt.

Generally, rejuvenators are used to supply missing components of aged asphalt, reverse the aging process, and are widely used in asphalt maintenance and recycling. However, compared with traditional rejuvenators, bio-oil rejuvenators are environmentally friendly, economical and efficient. This study looks into the effect of the three different bio-oils, namely sunflower oil, soybean oil, and palm oil, on the physical properties, rheological properties and chemical components of aged asphalt at different dosages. The asphalt physical properties and Dynamic Shear Rheological (DSR) test results show that with the increase in bio-oil, the physical properties and rheological properties of rejuvenated asphalt are close to those of virgin asphalt, but the high-temperature rutting resistance needs to be further improved. The results of Fourier Transform Infrared Spectroscopy (FTIR) show that the carbonyl and sulfoxide indices of rejuvenated asphalt are much lower than those of aged asphalt. Moreover, the rejuvenation efficiency of aged asphalt mixed with sunflower oil is better than that with soybean oil and palm oil at the same dosage.

Development of an environmentally foamed concrete incorporating red mud.

In this work, an efficient utilization method for red mud (RM) is provided through recycling RM as a mineral admixture for the preparation of foamed concrete (FC). Specifically, FC with different RM contents was prepared and investigated in terms of workability, mechanical properties, and hydration products. Results show that adding RM can significantly shorten the setting time, while it inevitably weakens the mechanical properties and fluidity of FC. However, the compressive strength of FC can still meet the strength predicted by the specification requirements when the RM replaces cement with 60% content (3d > 1.6 MPa). Most importantly, the heavy metals leaching from RM-based FC under the action of rain is still unclear, so a device for simulating stormwater runoff was designed to test the heavy metal leaching risk of RM-based FC. The findings indicate that the solidification of cement and the high basicity of the matrix can effectively reduce the leaching risk of heavy metals from RM in FC. Although the pore structure analysis demonstrates that the porosity and connected pores of FC will be deteriorated as RM concentration increases. The results are of great significance for the recycling of waste and the sustainable development of building materials.

Exploring the Utilization of PHC Pile Waste Concrete as Filler in Asphalt Mastics.

Using solid waste to replace limestone filler in asphalt concrete can not only reduce the cost of road construction, but also improve the utilization rate of solid waste. In this study, PHC pile waste concrete (PPWC) was innovatively used to replace limestone filler in asphalt mixture and its effect on the physical and rheological properties of asphalt mastics was studied. Firstly, PPWC was ground into filler particles with a diameter less than 0.075 mm. The physical properties, particle characteristics and chemical composition of PPWC filler and limestone filler were compared. Asphalt mastics were prepared with different filler-asphalt volume ratios (20%, 30% and 40%) and the physical properties, high-temperature rheological properties and low-temperature cracking resistance of asphalt mastics were tested. The experimental results showed that the surface of PPWC filler is rougher and has lower density and smaller particle size than limestone filler. When the filler content is the same, PPWC filler asphalt mastics have lower penetration and ductility, higher softening point than limestone filler asphalt mastics, and the viscosity of PPWC filler asphalt mastics is more sensitive than limestone filler asphalt mastics. PPWC filler asphalt mastics demonstrated superior high-temperature stability, but poorer low-temperature cracking resistance compared to limestone filler asphalt mastics. In conclusion, PPWC fillers can be used to replace limestone fillers in asphalt mixtures. The finding of this study will provide a new solution for the construction of eco-friendly roads.

Optimization of Asphalt-Mortar-Aging-Resistance-Modifier Dosage Based on Second-Generation Non-Inferior Sorting Genetic Algorithm.

The use of steel slag powder instead of filler to prepare asphalt mortar was beneficial to realize the effective utilization of steel slag and improve the performance of asphalt concrete. Nevertheless, the anti-aging properties of steel-slag powder-asphalt mortar need to be further enhanced. This study used antioxidants and UV absorbers in steel-slag powder-asphalt mortar to simultaneously improve its thermal-oxidation and UV-aging properties. The dosage of modifier was optimized by second-generation non-inferior sorting genetic algorithm. Fourier-Transform Infrared Spectroscopy, a dynamic shear rheometer and the heavy-metal-ion-leaching test were used to evaluate the characteristic functional groups, rheological properties and heavy-metal-toxicity characteristics of the steel-slag-powder-modified asphalt mortar, respectively. The results showed that there was a significant correlation between the amount of modifier and G*, δ, and the softening point. When the first peak appeared for G*, δ, and the softening point, the corresponding dosages of x1 were 2.15%, 1.0%, and 1.1%, respectively, while the corresponding dosage of x2 were 0.25%, 0.76%, and 0.38%, respectively. The optimal value of the modifier dosage x1 was 1.2% and x2 was 0.5% after weighing by the NSGA-II algorithm. The asphalt had a certain physical solid-sealing effect on the release of heavy-metal ions in the steel-slag powder. In addition, the asphalt structure was changed under the synergistic effect of oxygen and ultraviolet rays. Therefore, the risk of leaching heavy-metal ions was increased with the inferior asphalt-coating performance on the steel-slag powder.