Changes in Porous Parameters of the Ion Exchanged X Zeolite and Their Effect on CO2 Adsorption.

Zeolite 13X (NaX) was modified through ion-exchange with alkali and alkaline earth metal cations. The degree of ion exchange was thoroughly characterized with ICP, EDS and XRF methods. The new method of EDS data evaluation for zeolites was presented. It delivers the same reliable results as more complicated, expensive, time consuming and hazardous ICP approach. The highest adsorption capacities at 273 K and 0.95 bar were achieved for materials containing the alkali metals in the following order K < Na < Li, respectively, 4.54, 5.55 and 5.94 mmol/g. It was found that it is associated with the porous parameters of the ion-exchanged samples. The Li0.61Na0.39X form of zeolite exhibited the highest specific surface area of 624 m2/g and micropore volume of 0.35 cm3/g compared to sodium form 569 m2/g and 0.30 cm3/g, respectively. The increase of CO2 uptake is not related with deterioration of CO2 selectivity. At room temperature, the CO2 vs. N2 selectivity remains at a very high stable level prior and after ion exchange in co-adsorption process (XCO2 during adsorption 0.15; XCO2 during desorption 0.95) within measurement uncertainty. Additionally, the Li0.61Na0.39X sample was proven to be stable in the aging adsorption-desorption tests (200 sorption-desorption cycles; circa 11 days of continuous process) exhibiting the CO2 uptake decrease of about 6%. The exchange with alkaline earth metals (Mg, Ca) led to a significant decrease of SSA and micropore volume which correlated with lower CO2 adsorption capacities. Interestingly, the divalent cations cause formation of mesopores, due to the relaxation of lattice strains.

Sorption and Textural Properties of Activated Carbon Derived from Charred Beech Wood.

The aim of this study was to prepare activated carbon materials with different porous structures. For this purpose, the biomass precursor, beech wood, was carbonized in an inert atmosphere, and the obtained charcoal was physically activated using carbon dioxide at 1273 K. Different porous structures were obtained by controlling the time of the activation process. Prepared materials were characterized in terms of textural (N2 sorption at 77 K), structural (XRD), and sorption properties (CO2, C2H4, C4H10). The shortest activation time resulted in a mostly microporous structure, which provided a high sorption of CO2. Increasing the activation time led to an increasing of the pores' diameters. Therefore, the highest ethene uptake was obtained for the material with an intermediate activation time, while the highest butane uptake was obtained for the material with the highest activation time.

Nanocomposite Titania-Carbon Spheres as CO2 and CH4 Sorbents.

Photocatalysis can offer solutions for the transformation of greenhouse gases, such as methane and carbon dioxide. In the paper, a candidate for such a photocatalyst is presented, based on a composite of titania with carbon spheres. The material was obtained using microwave assisted solvothermal synthesis, enabling good dispersion of titania. The studies of carbon dioxide and methane adsorption were performed under ambient pressure and temperatures of 40, 60, and 80 °C. The effect of temperature increase was less favorable for carbon dioxide than for methane. Satisfying values of carbon dioxide and methane uptake were obtained-3.94 mmol CO2/g and 2.77 mmol CH4/g at 40 °C.

Investigations on the Properties and Performance of Mixed-Matrix Polyethersulfone Membranes Modified with Halloysite Nanotubes.

Ultrafiltration (UF) polyethersulfone (PES) membranes were prepared by wet phase inversion method. Commercial halloysite nanotubes (HNTs) in the amount of 0.5-4 wt % vs PES (15 wt %) were introduced into the casting solution containing the polymer and N,N-dimethylformamide as a solvent. The morphology, physicochemical properties and performance of the membranes were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM), zeta potential, porosity and contact angle analyses, as well as permeability measurements. Moreover, the antifouling properties of the membranes were evaluated during UF of a model solution of bovine serum albumin (BSA). The research revealed a positive influence of modification with HNTs on hydrophilicity, water permeability and antifouling properties of the PES membranes. The most significant improvement of permeability was obtained in case of the membrane containing 2 wt % of HNTs, whereas the highest fouling resistance was observed for 0.5 wt % HNTs content. It was found that a good dispersion of HNTs can be obtained only at loadings below 2 wt %. Based on the results a relation between severity of membrane fouling and surface roughness was proved. Moreover, an increase of the roughness of the modified membranes was found to be accompanied by an increase of isoelectric point values.