RESUMEN
It is a challenging issue for the creation of photogenerated carrier collectors on the photocatalyst to drive charge separation and promote reaction kinetics in the photocatalytic reaction. Herein, based on one-step dual-modulation strategy, IrO2 nanodots are modified at the edge of polymeric carbon nitride (PCN) nanosheets and atomically dispersed Ir atoms are implanted in the skeleton of PCN to obtain a unique Ir-PCN/IrO2 photocatalyst. IrO2 nanodots and atomically dispersed Ir atoms act as hole and electron collectors to synergistically promote the carrier separation and reaction kinetics, respectively, thereby greatly improving the photocatalytic hydrogen evolution (PHE) performance. As a result, without adding additional cocatalyst, the PHE rate over the optimal Ir-PCN/IrO2-2% sample reaches up to 1564.4 µmol h-1 g-1 under the visible light irradiation, with achieving an apparent quantum yield (AQY) of 15.7% at 420 nm.
RESUMEN
Near-field passive wireless sensors can realize non-contact strain measurement, so these sensors have extensive applications in structural health monitoring. However, these sensors suffer from low stability and short wireless sensing distance. This paper presents a bulk acoustic wave (BAW) passive wireless strain sensor, which consists of two coils and a BAW sensor. The force-sensitive element is a quartz wafer with a high quality factor, which is embedded into the sensor housing, so the sensor can convert the strain of the measured surface into the shift of resonant frequency. A double-mass-spring-damper model is developed to analyze the interaction between the quartz and the sensor housing. A lumped parameter model is established to investigate the influence of the contact force on the sensor signal. Experiments show that a prototype BAW passive wireless sensor has a sensitivity of 4 Hz/µÎµ when the wireless sensing distance is 10 cm. The resonant frequency of the sensor is almost independent of the coupling coefficient, which indicates that the sensor can reduce the measurement error caused by misalignment or relative movement between coils. Thanks to the high stability and modest sensing distance, this sensor may be compatible with a UAV-based monitoring platform for the strain monitoring of large buildings.
RESUMEN
This work presents a unique approach to the design, fabrication, and characterization of paper-based origami robotic systems consisting of stackable pneumatic actuators. These paper-based actuators (PBAs) use materials with high elastic modulus-to-mass ratios, accordion-like structures, and direct coupling with pneumatic pressure for extension and bending. The study contributes to the scientific and engineering understanding of foldable components under applied pneumatic pressure by constructing stretchable and flexible structures with intrinsically nonstretchable materials. Experiments showed that a PBA possesses a power-to-mass ratio greater than 80 W/kg, which is more than four times that of human muscle. This work also illustrates the stackability and functionality of PBAs by two prototypes: a parallel manipulator and a legged locomotor. The manipulator consisting of an array of PBAs can bend in a specific direction with the corresponding actuator inflated. In addition, the stacked actuators in the manipulator can rotate in opposite directions to compensate for relative rotation at the ends of each actuator to work in parallel and manipulate the platform. The locomotor rotates the PBAs to apply and release contact between the feet and the ground. Furthermore, a numerical model developed in this work predicts the mechanical performance of these inflatable actuators as a function of dimensional specifications and folding patterns. Overall, we use stacked origami actuators to implement functionalities of manipulation, gripping, and locomotion as conventional robotic systems. Future origami robots made of paper-like materials may be suitable for single use in contaminated or unstructured environments or low-cost educational materials.
Asunto(s)
Robótica , Módulo de Elasticidad , Diseño de Equipo , Humanos , Robótica/métodosRESUMEN
This article describes a process of fabricating highly porous paper from cellulosic fibers and carbon black (CB) with tunable conductivity. By embossing such paper, its porosity decreases while its conductivity increases. Tuning the porosity of composite paper alters the magnitude and trend of conductivity over a spectrum of concentrations of conductive particles. The largest increase in conductivity from 8.38 × 10-6 to 2.5 × 10-3 S/m by a factor of â¼300 occurred at a percolation threshold of 3.8 wt % (or 0.36 vol %) with the composite paper plastically compressed by 410 MPa, which caused a decrease of porosity from 88% to 42% on average. Our composite paper showed stable piezoresistive responses within a broad pressure range from 1 kPa up to 5.5 MPa for 800 cycles. The piezoresistive sensitivities of the composite paper were dependent on concentration and decreased with pressure. Composite paper with 7.5 wt % CB had sensitivities of -0.514 kPa-1 over applied pressures ranging from 1 to 50 kPa and -0.215 kPa-1 from 1 to 250 kPa. This piezoresistive paper with embossed patterns enabled touch sensing and detection of damage from darts and punches. Understanding the percolation behavior of three-phase composites (cellulosic fibers/conductive particles/air) and their response to damage, pressure, and processing conditions has the potential to enable scalable applications in prosthetics and robotics, haptic feedback, or structural health monitoring on expansive surfaces of buildings and vehicles.
RESUMEN
This article presents a sensor for detecting the distribution of forces on a surface. The device with nine buttons consisted of an elastomer-based layer as a touch interface resting on a substrate of patterned metallized paper. The elastomer-based layer included a three-by-three array of deformable, hemispherical elements/reliefs, facing down toward an array of interdigitated capacitive sensing units on patterned metallized paper. Each hemispherical element is 20 mm in diameter and 8 mm in height. When a user applied pressure to the elastomer-based layer, the contact area between the hemispherical elements and the interdigitated capacitive sensing units increased with the deformation of the hemispherical elements. To enhance the sensitivity of the sensors, embedded particles of hydrogel in the elastomer-based layer increased the measured electrical responses. The measured capacitance increased because the effective dielectric permittivity of the hydrogel was greater than that of air. Electromechanical characterization verified that the hydrogel-filled elastomer was more sensitive to force at a low range of loads (23.4 pF/N) than elastomer alone without embedded hydrogel (3.4 pF/N), as the hydrogel reduced the effective elastic modulus of the composite material by a factor of seven. A simple demonstration suggests that the force-sensing array has the potential to contribute to wearable and soft robotic devices.