Novel three-stage microalgal cultivation system for lipid production utilizing nutrients derived from refinery waste.

The pollution and transformation of refineries are receiving increasing attention. The carbonic anhydrase in Tetradesmus obliquus was found exhibiting a hysteresis phenomenon in response to periodic changes in the composition of external carbon sources, with a surge in inorganic carbon concentration stressing the carbonic anhydrase activity to increase by 6-9 times. On this basis, a novel three-stage culture system of T. obliquus was proposed, which mainly uses refinery waste as the nutrients. By controlling the nutrient content in the environment, especially the composition of carbon sources, microalgae could sequentially complete rapid biomass accumulation, efficient inorganic carbon assimilation, and oil production. Compared to a single-environment culture system, the biomass yield increased by 1.34 times, the oil content increased by more than 6%, and the oil productivity increased by 2.08 times. Above findings may lay a partial theoretical foundation for the future evolution of traditional refineries towards "fossil-algal-biomass" hybrid refineries.

Utilization of opium poppy seed oil for biodiesel production: A parametric characterization and statistical optimization.

Consuming traditional petroleum-derived diesel fuel has long been associated with issues such as the depletion of natural energy resources. To solve these challenges, an alternate source like as biodiesel is an appealing option. Seed oils have long been recognized as an abundant and diverse source of biodiesel. In this study, poppy seed oil from the poppy (Papaver somniferum) was investigated for biodiesel production. Poppy seed biodiesel was generated and refined using acid-pretreated esterification with sulphuric acid prior to transesterification, as well as single-step alkaline catalyzed transesterification with methanol and potassium hydroxide. Finally, the percentage yield was compared. Using Statistica, the Box-Behnken design was applied to optimize process variables like time, temperature, catalyst concentration, and methanol-oil ratio to produce maximum yield. The relationship of process variables was also shown with the help of the Response Surface Methodology. A maximum yield of 94.87 % was obtained at optimized conditions, i.e., 90min reaction time, 60 °C of temperature, 0.25 mg of catalyst concentration, and 3v/v% alcohol-oil ratio. The fuel properties of biodiesel produced, such as acid value, moisture content, saponification value, iodine value, specific gravity, percentage of free fatty acids, refractive index, viscosity, boiling point, and peroxide value, were measured and compared with the American Society for Testing and Materials (ASTM) D6751 and European Standards (EN) 14214. Further results were studied and discussed using Fourier Transfer Infrared (FTIR) analysis, which showed maximum similarity of raw material to formed biodiesel. Gas Chromatography-Mass Spectrometry (GC-MS) analysis was performed to identify and quantify various fatty acid methyl esters. The results obtained were in accordance with various international standards for biodiesel fuel. Thus, poppy seeds can be used to obtain biodiesel.

Investigation on nanostructure, surface functional groups, and oxidation activity of particulate along the exhaust after-treatment of a diesel engine fueled with waste cooking oil biodiesel blends.

In this study, the nanostructure, surface functional groups, and oxidation activity of soot particulate along the exhaust after-treatment system of a heavy-duty diesel engine fueled with waste cooking oil (WCO) biodiesel blends are investigated by TEM, XPS, and TGA respectively. The main findings are as follows: Along the exhaust after-treatment system, fringe length of primary particles of soot particulate emitted from tested heavy-duty diesel engine fueled with B0, B10, B20, and B100, i.e., 0%, 10%, 20%, and 100% ratio of WCO biodiesel blended into petroleum diesel in volume respectively increases, while fringe tortuosity and separation distance of primary particles reduces. The fringe length of B10, B20, and B100 is smaller, but the fringe tortuosity and separation distance are larger than that of B0. The O/C ratio of soot particulate tends to increase firstly and then decrease as the exhaust passes through DOC+cDPF and SCR+ASC in sequence. The O/C ratio of B10, B20, and B100 are also higher than that of B0. Soot particulate at cDPF outlet contains carborundum and biuret is found at SCR+ASC outlet. The sp3/sp2 ratio decreases along the exhaust after-treatment system, and B10, B20, and B100 tend to get higher sp3/sp2 ratio than B0. The C-OH and C=O content of soot particulate from different WCO biodiesel blends show generally similar trends along the exhaust after-treatment system, while the activation energy of soot particulate keeps increasing along the exhaust after-treatment system, but decreases with the increasing of blend ratio. These findings can provide useful references for optimizing the after-treatment system for WCO biodiesel blends.

The evaluation of Starmerella magnoliae X3 as a biodiesel feedstock based on triacylglycerol (TAG) production, lipid productivity, and fatty acid profile under nitrogen limitation and acidic pH conditions.

The effects of four initial culture pH values (3, 4, 5, and 6) and nitrogen limitation on growth, TAG accumulation, lipid production, fatty acid profile, and estimated biodiesel quality of Starmerella magnoliae X3 were investigated. TAG and lipid levels were measured by Nile Red fluorescence and sulfo-phospho-vanilin (SPV) techniques, respectively. The results showed that a combination of nitrogen limitation and acidic pH significantly (p < 0.05) increased TAG accumulation, total lipid contents, and lipid productivity in Starmerella magnoliae X3 compared to the control group. Under nitrogen limitation, the highest TAG accumulation was achieved at initial pHs of 3 and 5 after 72 h of cultivation, and the highest lipid productivity (0.306 g L-1 d-1) was observed after 48 h at pH 3; the major fatty acids at the four pH values were oleic acid (63.6%-64%), palmitoleic acid (11.3%-12.5%), stearic acid (9.7%-11.4%), and palmitic acid (9.4%-10%). In addition, both stresses were associated with lower iodine value and higher cetane number of the biodiesel compared to the control. These findings suggest that cultivation in a low-nitrogen medium at an initial pH of 3 or 5 holds promise in increasing TAG production in Starmerella magnoliae X3.

Transesterification of waste cooking oil for biodiesel production using alkaline-modified graphitic carbon nitride heterogeneous catalyst.

Developing efficient, stable, cost-effective, and environmentally benign heterogeneous catalysts for transesterification is highly required for sustainable biodiesel production. The present study explores the biodiesel production from waste cooking oil (WCO) using graphitic carbon nitride (g-C3N4) and its alkaline-modified nanocatalyst. The catalysts were characterised by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy Dispersive X-ray spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR). From the XRD analysis, crystalline sizes of g-C3N4 and alkaline g-C3N4 were found to be 26 and 29 nm, respectively. Transesterification of WCO was carried out at 60 °C for a reaction time of 2 h using 2 wt.% of g-C3N4 and alkaline g-C3N4. Transesterification reaction catalysed by alkaline-modified g-C3N4 was found with a higher yield of biodiesel (89%) than the biodiesel yield (78%) with transesterification reaction catalysed by g-C3N4. The recyclability of both catalysts was also evaluated by reusing them for up to the 5th cycle. The obtained biodiesel was analyzed by using FTIR and GC-MS. The synthesised biodiesel was found to have significant level of monounsaturated fatty acids and saturated fatty acids, which make it usefuel for use as fuel. Some physicochemical properties of the obtained biodiesel were also calculated and found appropriate as per the American Society for Testing and Materials (ASTM) standards. With high reusability and good catalytic activity, the synthesised alkaline-modified g-C3N4 can be employed as a viable option for biodiesel production from WCO.

Current Scenario and Global Perspective of Sustainable Algal Biofuel Production.

Industrialization and globalization have increased the demand for petroleum products that has increased a load on natural energy resources. The escalating fossil fuel utilization has resulted in surpassing the Earth's capacity to absorb greenhouse gases, necessitating the exploration of sustainable bioenergy alternatives to mitigate emissions. Biofuels, derived from algae, offer promising solutions to alleviate fossil fuel dependency. Algae, often regarded as third-generation biofuels, present numerous advantages owing to their high biomass production rates. While algae have been utilized for their bioactive compounds, their capability as biomass for the production of biofuel has gained traction among researchers. Various biofuels such as bio-hydrogen, bio-methane, bio-ethanol, bio-oil, and bio-butanol can be derived from algae through diverse processes like fermentation, photolysis, pyrolysis, and transesterification. Despite the enormous commercial potential of algae-derived biofuels, challenges such as high cultivation costs persist. However, leveraging the utilization of algae byproducts could improve economic viability of biofuel production. Moreover, algae derived biofuels offer environmental sustainability, cost-effectiveness, and waste reduction benefits, promising novel opportunities for a more sustainable energy future.

Response surface optimization of a single-step castor oil-based biodiesel production process using a stator-rotor hydrodynamic cavitation reactor.

In order to combat environmental pollution and the depletion of non-renewable fuels, feasible, eco-friendly, and sustainable biodiesel production from non-edible oil crops must be augmented. This study is the first to intensify biodiesel production from castor oil using a self-manufactured cylindrical stator-rotor hydrodynamic cavitation reactor. In order to model and optimize the biodiesel yield, a response surface methodology based on a 1/2 fraction-three-level face center composite design of three levels and five experimental factors was used. The predicted ideal operating parameters were found to be 52.51°C, 1164.8 rpm rotor speed, 27.43 min, 8.4:1 methanol-to-oil molar ratio, and 0.89% KOH concentration. That yielded 95.51% biodiesel with a 99% fatty acid methyl ester content. It recorded a relatively low energy consumption and high cavitation yield of 6.09 × 105 J and 12 × 10-3 g/J, respectively. The generated biodiesel and bio-/petro-diesel blends had good fuel qualities that were on par with global norms and commercially available Egyptian petro-diesel. The preliminary cost analysis assured the feasibility of the applied process.

Thermal and emission analysis of waste plastic and microalgae biodiesel as a potential power source for diesel engines: A sustainable approach.

The future of diesel engines is greatly influenced by ongoing research on alternative fuels. Renewable fuels have been researched and adopted by several nations to encourage the production and use of biodiesel. This study examines the energy conversion of waste plastic biodiesel and Spirulina microalgae biodiesel at a 20% blending ratio to analyze the behavior of a one-cylinder, 4-stroke diesel engine running at 1500 rpm with a compression ratio of 17.5. The authors evaluated, analyzed, and compared the engine's combustion, performance, and emission at an incremental engine load of 25% from 25 to 100%. The findings demonstrated that the biodiesel fuel samples generated somewhat poorer efficiency but reduced emissions from the engine. At 100% load, the percentage differences between the diesel and blended fuel samples ranged from 2.4 to 7.3% for BTE, 2.9 to 16.5% for BSFC, and 1.0 to 4.62% for BSEC; however, the PM, SO2, and CO2 emissions were reduced by 1.6-28.8% except for NOx emissions, which are increased by up to 9.4%. Pure diesel exhibits the best performance characteristics; however, pure biodiesel exhibits the best emission characteristics. The 20% blended fuels showed promising results, as they exhibited comparable or slightly improved BTE values compared to their respective pure biodiesel fuels. The findings indicate that Spirulina microalgae biodiesel and waste plastic biodiesel have the potential to be utilized as substitute fuels for diesel engines; however, for the greatest performance and lowest emissions, their blending ratios and engine operating conditions must be optimized.

Enhanced machining of Al 10%SiCmicro 1%SiCnano hybrid composite using rotary tool rotary workpiece EDM with bio dielectrics and treated tools.

A sustainable approach was proposed to address environmental pollution, carbon footprint and economic efficiency challenges in Electrical Discharge Machining (EDM). This approach involved the use of Bio-dielectric such as biodiesel and Bio fuel (distilled water with 10% ethanol). The EDM process performance was further optimized by experimenting with both electrodes' rotation (i.e., in same direction, opposite direction, no rotation) and the use of treated tools (no treatment, heat treatment, cryogenic treatment). Biodiesel as a bio-dielectric showed promise by delivering the highest Material Removal Rate (MRR) and the lowest Tool Wear Rate (TWR). Bio-fuel (distilled water with 10% ethanol) resulted in the lowest Surface Roughness (SR) and cleaner machined surface with least carbon deposition. Additionally, electrode rotation improved flushing and enhanced performance parameters, with opposite direction rotation yielding the highest MRR and the lowest SR. However, no rotation of electrodes resulted in the lowest TWR. The use of treated tools, specifically heat-treated and cryogenically treated tools, also improved performance and reduced energy consumption, with cryogenic treatment providing the highest MRR, heat treatment giving least SR, and no treatment providing least TWR. Certain interactions between factors significantly impacted performance parameters. Grey relational analysis revealed that using distilled water with 10% ethanol as a dielectric, employing cryogenically treated copper tools, and having no rotation of both electrodes yielded the best performance parameters.

Production of 1,3-propanediol via in situ glycerol hydrogenolysis in aqueous phase reforming using bimetallic W-Ni/CeO2.

The production of 1,3-propanediol via in situ glycerol hydrogenolysis and aqueous phase reforming is a promising technique to ensure high product yield with shorter reaction times and lower costs, as demonstrated in this study by investigating the effect of tungsten (W) doping on Ni/CeO2 catalysts. Physicochemical properties of catalyst were determined using XRD, H2-TPR, NH3-TPD, BET, and FESEM-EDX techniques, and the catalytic performance was investigated at 230 °C, 20 bar, and 5 wt.% glycerol in an autoclave batch reactor. W doping ranging from 1-7% improved the catalyst's performance, with 3% W in 10% Ni/CeO2 (3W10NC) achieving the highest yield (2.4%), selectivity (33.3%), and a good conversion rate (72.18%). The effect of reaction parameter on the 3W10NC catalyst showed that increasing pressure and temperature from the initial parameters had a detrimental effect on 1,3-propanediol attributed to the phenomenon called over-hydrogenolysis. Increasing the glycerol concentration to 20 wt.% also had a positive effect, resulting in the highest 1,3-propanediol yield of 22.27%. The effect of reaction time study revealed that the yield of 1,3-propanediol continued to increase steadily, reaching 38.29% after 4 h of reaction under the optimal conditions of 230 °C, 20 bar, and 20 wt.% glycerol. The kinetic study confirmed that the reaction follows first-order reaction with activation energy of 20.104 kJ mol-1. The catalyst reusability test revealed a decrease in the yield of 1,3-propanediol to 32.55%, likely due to deactivation caused by sintering and leaching, as indicated by the FESEM micrograph, EDX spectra, and NH3-TPD.

Lipid Accumulation and Biodiesel Production from Filamentous Cyanobacteria Native to Pakistan.

Depleting fossil fuel resources and increasing energy demand have intensified the emphasis on biofuel production cyanobacteria. In this study, 19 cyanobacterial filamentous strains were isolated from various regions of Pakistan, including the northern areas and the University of the Punjab, Lahore. Sudan black, Nile red, and BODIPY staining, together with CLSM, fluorimetry, FTIR, growth in different nitrate concentrations, and GC techniques, were used to confirm and measure the lipid and diesel contents within isolated cyanobacterial filaments. Oscillatoria sp. strain CFF-6 showed a significantly higher yield (biodiesel/ biomass=35.6%). Leptolyngbya sp. strain CFF-18 showed a higher yield (biodiesel/biomass=17.1%) compared to other Leptolyngbya strains. FAME (Fatty Acid Methyl Ester) analysis was also performed. Oscillatoria are better biodiesel producers in comparison to other filamentous strains.

Potential of oleaginous microbes for lipid accumulation and renewable energy generation.

Biocomponents (such as lipids) accumulate in oleaginous microorganisms and could be used for renewable energy production. Oleaginous microbes are characterized by their ability to accumulate high levels of lipids, which can be converted into biodiesel. The oleaginous microbes (including microalgae, bacteria, yeast, and fungi) can utilize diverse substrates. Thus, in this study, commercially viable oleaginous microorganisms are comparatively summarized for their growth conditions, substrate utilization, and applications in biotechnological processes. Lipid content is species-dependent, as are culture conditions (such as temperature, pH, nutrients, and culture time) and substrates. Lipid production can be increased by selecting suitable microorganisms and substrates, optimizing environmental conditions, and using genetic engineering techniques. In addition, the emphasis on downstream processes (including harvesting, cell disruption, lipid extraction, and transesterification) highlights their critical role in enhancing cost-effectiveness. Oleaginous microorganisms are potential candidates for lipid biosynthesis and could play a key role in meeting the energy needs of the world in the future.

Driving Sustainability in the United States: Efficacy of State-Level Biodiesel Policy Approaches.

The United States has significant greenhouse gas and criteria pollutant emissions that lead to global warming, human health, ozone, and smog issues, partially attributed to its diesel-consuming transport fleet. Until fleet electrification reaches cost parity with internal combustion engines, biodiesel use can reduce these negative impacts. In this study, we analyzed and categorized the biodiesel-supporting policies of each U.S. state using manual inductive coding to compare them against state-level biodiesel consumption and production. Through statistical modeling, we determined the efficacy of these policy approaches. The policy analysis identified that biodiesel policies that support infrastructure development and biodiesel production correlate significantly with increased biodiesel consumption at the state level. We also show that a combination of these policy categories correlates significantly with overall higher biodiesel consumption. Our methodological approach and policy analysis findings reveal valuable insight into the efficacy and outcomes from existing biofuel policies in the United States.

Optimization of Cultivation Conditions of Native Microalga Scenedesmus quadricauda and Evaluation of Lipids for Enhanced Biodiesel Production.

Biofuels are considered to be among the primary alternatives to the use of fossil fuels. These fuels, made from feedstock or waste raw materials, have the advantage of being renewable and contributing much less to global warming. Microalgae are a promising biodiesel source. Microalgae, unlike traditional crops that are now used to make commercialized biodiesel, may be grown on non-agricultural land and has a greater capacity for growth and yield. Cultivation has been considered as a critical stage in the generation of biofuels. The goal of the present study is to learn that Scenedesmus quadricauda has a potential for biodiesel production in the near future. Optimization studies revealed that BG-11 medium, temperature of 25 °C, pH 7.0, glucose and sucrose (as carbon sources), static condition (for lipid accumulation) & shaking condition (for biomass yield), cultivation days of 18, 21, and 24 day, NaNO3 dosing of 1.0 mM followed by 0.8 mM (on 5th day of cultivation), 3% yeast extract dosing, 3000 lx light intensity, photoperiod cycles of 24L/0D (for biomass yield) and 18L/6D (for lipid production) and 10 mM concentration of NaCl (salinity stress) can be regarded as best suited physio-biochemical parameters for efficient biomass and lipid yield from S. quadricauda. FTIR indicated presence of various stretching of carbohydrates and lipids that again is supporting biodiesel production capability of S. quadricauda. SEM showed that cells of S. quadricauda under stress conditions became fragmented separated from coenobium and were not so compactly arranged. Present optimization studies along with Nile red fluorescence, FTIR and SEM revealed that S. quadricauda could be a suitable candidate to produce good quality biofuel and that also in stress conditions.

Development of Free Fatty Acid (FFA) monitoring device for evaluation of oil samples used for biodiesel production.

Diversion of oil sources for biodiesel production has been gaining importance to meet the environmental concerns and energy demand. The free fatty acid (FFA) content of the feedstock is a significant factor in biodiesel production. The FFA values determine the complexity of the biodiesel production. Until date, an experimental procedure has been used to determine the FFA concentration of an oil source; this method is dependent on titration, which is a laborious process involving significant volumes of chemicals. Hence, in the present study, an attempt was made to develop a device for the identification of FFA of the oils. Waste cooking oil samples subjected to wide range of cooking conditions like cooking time, temperature, type of food are collected from different food outlets. Subsequently, the composition of oil samples and the variation in their quality were analysed using gas chromatography flame ionization detector (GC - FID). Biodiesel is prepared from the oil samples through transesterification and the impact of FFA and their respective methyl esters in the quality and properties have been investigated. The properties of biodiesel were determined as per ASTM standards. The study was further extended to correlate the properties of biodiesel with the composition of the oil from which it was derived. The analysis evidently proved the dependence of biodiesel properties on the FFA percentage and the composition of the oil. The results have been further substantiated with the performance and emission characteristics of internal combustion engine fuelled with the prepared biodiesel samples.

Isolation and identification of a salt-tolerant Coelastrum sp. and exploration of its potential for biodiesel production.

Given the escalating demand for renewable biofuels amidst the continual consumption of fossil energy, the exploration and identification of microalgal strains for biodiesel production have become crucial. In this study, a microalgal strain named HDMA-12 was isolated from Lake Chenjiadayuan in China to evaluate its biodiesel potential. Phylogenetic analysis of its internal transcribed spacer sequences revealed HDMA-12 as a new molecular record in the genus Coelastrum. When cultivated in BG11 basal medium, HDMA-12 achieved a biomass of 635.7 mg L-1 and a lipid content of 26.4%. Furthermore, the fatty acid methyl ester profile of HDMA-12 exhibited favorable combustion characteristics. Subjected to 200 mM NaCl stress, HDMA-12 reached its maximum biomass of 751.5 mg L-1 and a lipid content of 28.9%. These findings indicate the promising prospects of HDMA-12 as a promising microalgal strain for further advancements in biodiesel production.

Biodiesel production from agricultural biomass wastes: Duroc breed fat oil, Citrillus lanatus rind, and Sorghum Bagasse.

This research study synthesized a base catalyst from the waste Citrullus lanatus rind (WCLR) for the synthesis of biodiesel from the waste pig fat oil. The high-acid-value oil (high free fatty acid: FFA) was converted to low-acid-value oil through adsorption in sorghum bagasse ash with high particle sizes. The developed base catalyst was obtained from the WCLR and was characterized via thermogravimetric analysis (TGA), Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD-FT), and Brunauer-Emmett-Teller (BET) adsorption analysis. The properties of biodiesel were compared with the recommended standard. Results reflected that the duroc breed pig fat is rich in oil, and the oil is unsaturated. Sorghum bagasse proved to be a good bio-adsorbent for the unsaturated fat FFA reduction. The catalyst produced from WCLR was found to be rich in potassium-calcium-magnesium (K-Ca-Mg) base salts. The predicted yield of 98.69 % (wt./wt.) at 69.96 min, 79.93 °C, 3.15 % (wt.), and 8.57 (vol.) at desirability of 100 % was validated as 98.52 % (wt./wt.). Catalytic strength can be recycled in five cycles. The cost implications indicated that the cost of producing 25 L of biodiesel is $2.61. This study proved to be the most economical way of producing biodiesel that is environmentally friendly, cost-effective, and easy to produce for future energy needs.•Oil was obtained via rendering from duroc breed waste fat oil.•Sorghum bagasse was used as adsorbent for acid reduction of high FFA pig fat oil.•Base catalyst used was obtained from calcined waste Citrullus lanatus rind.

The potential of magnesium oxide nanoparticles (MgONPs) in the transesterification of lipids produced by Rhodotorula minuta.

The urgent need to address energy security risks and global warming has led to exploration of renewable energy sources. One such avenue is biodiesel specifically focusing on the potential of Rhodotorula minuta, a type of yeast known for producing lipids that can be used as a sustainable alternative for production of biodiesel. In the current study, this promising yeast was evaluated for its potential to produce lipids. The morphological characterization was carried out by scanning electron microscope (SEM), and intracellular detail was studied by transmission electron microscope (TEM). Changes in content and cellular biomass were monitored at time intervals with the highest biomass yield of 12.4 g/l and lipid content of 6.2 g/l achieved after 72 h. In the present work, magnesium oxide nanoparticles (MgO NPs) were synthesized and extensively characterized through Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET), SEM, TEM, and X-ray diffraction (XRD). By employing response surface methodology (RSM) with Box-Behnken design (BBD), optimal process conditions for transesterification could be determined. The best result achieved was a yield of 88.6% when the conditions were optimized, using methanol to oil ratio of 18:1 and 8% (w/w) amount of catalyst maintaining a reaction temperature of 55 °C and allowing the reaction to proceed for 120 min.

Comparison of potassium catalysts on zeolite sodium A and X in transesterification of palm oil and active species specification.

Heterogeneous catalysts consisting of potassium supported on zeolites are active for transesterification, but the effect of zeolite properties is not clearly understood. This work compares catalysts containing 12 wt.% potassium on zeolite sodium A and X (12K/NaA and 12K/NaX) in terms of performance and physicochemical properties. Both catalysts were prepared by ultrasound-assisted impregnation with potassium acetate buffer. 12K/NaA is a better catalyst in transesterification of palm oil, giving a higher biodiesel yield than 12K/NaX in the first run (99.1 ± 0.3 % and 77.9 ± 2.2 %, respectively). From characterization by CO2-TPD, XRD, FTIR, XPS, and SEM-EDS, both catalysts have similar basicity but different dispersion of carbonates and interaction on the zeolites. The 12K/NaA has those species on external surfaces and more monodentate carbonate than 12K/NaX. Ion exchange occurs between potassium ions from the precursor and sodium ions from the zeolite. Moreover, 12K/NaA is more stable, providing higher biodiesel yields in the second and third catalytic cycles.

RSM integrated GWO, Driving Training, and Election-Based Algorithms for optimising ethylic biodiesel from ternary oil of neem, animal fat, and jatropha.

The worldwide exploration of the ethanolysis protocol (EP) has decreased despite the multifaceted benefits of ethanol, such as lower toxicity, higher oxygen content, higher renewability, and fewer emission tail compared to methanol, and the enhanced fuel properties with improved engine characteristics of multiple-oily feedstocks (MOFs) compared to single-oily feedstocks. The study first proposed a strategy for the optimisation of ethylic biodiesel synthesis from MOFs: neem, animal fat, and jatropha oil (NFJO) on a batch reactor. The project's goals were to ensure environmental benignity and encourage the use of totally biobased products. This was made possible by the introduction of novel population based algorithms such as Driving Training-Based Optimization (DTBO) and Election-Based Optimization (EBOA), which were compared with the widely used Grey Wolf Optimizer (GWO) combined with Response Surface Methodology (RSM). The yield of NFJO ethyl ester (NFJOEE) was predicted using the RSM technique, and the ideal transesterification conditions were determined using the DTBO, EBOA, and GWO algorithms. Reaction time showed a strong linear relationship with ethylic biodiesel yield, while ethanol-to-NFJO molar ratio, catalyst dosage, and reaction temperature showed nonlinear effects. Reaction time was the most significant contributor to NFJOEE yield.The important fundamental characteristics of the fuel categories were investigated using the ASTM test procedures. The maximum NFJOEE yield (86.3%) was obtained at an ethanol/NFJO molar ratio of 5.99, KOH content of 0.915 wt.%, ethylic duration of 67.43 min, and reaction temperature of 61.55 °C. EBOA outperforms DTBO and GWO regarding iteration and computation time, converging towards a global fitness value equal to 7 for 4 s, 20 for 5 s and 985 for 34 s. The key fuel properties conformed to the standards outlined by ASTMD6751 and EN 14,214 specifications. The NFJOEE fuel processing cost is 0.9328 USD, and is comparatively lesser than that of conventional diesel. The new postulated population based algorithm models can be a prospective approach for enhancing biodiesel production from numerous MOFs and ensuring a balanced ecosystem and fulfilling enviromental benignity when adopted.