Silver Nanowire Aerogel Support Promotes Stable Hydrogen Evolution Reaction at High Current Density.

The stability of electrocatalysts during the hydrogen evolution reaction (HER) is vital for efficient production of hydrogen energy. Herein, we demonstrate that silver nanowire aerogel-based support (AABS) could facilitate the construction of HER catalysts with extraordinary long-term stability. A full nanostructure catalyst of nickel phosphide based formed on AABS (Ni2P-Ni5P4@AABS) was prepared to achieve an overpotential of 687 mV (without iR compensation) for HER at the current density of 1 A cm-2 in 0.5 M H2SO4. Excitingly, the stable HER performance was kept for 42 days during the long-term stability (i-t) test at high current density (0.5-1 A cm-2). The excellent HER performance of the Ni2P-Ni5P4@AABS catalyst is attributed to rapid electron transport pathways, numerous more accessible active sites, and support induced enhanced catalytic activity. The support effect was highlighted by a proposed phenomenological two-channel model for electron transport, which provides fresh insights into the design strategy for energy storage and delivery.

Long-term stability of sufentanil quantified by UPLC-MS-MS in human plasma frozen for 11 years at -20°C.

The long-term stability of drug concentrations in human plasma samples when stored under normal laboratory conditions over several years is important for research purposes and clinical re-evaluation, but also for forensic toxicology. Fifty human plasma samples from a former clinical trial were re-analyzed after storage at -20°C for 11 years. Plasma samples were extracted using solid-phase extraction. Isotope labelled sufentanil-D5 was used as internal standard. Sufentanil plasma concentrations were determined by ultra-performance liquid chromatography (UPLC) with gradient elution, followed by tandem mass spectrometry with electrospray ionization. The linear dynamic range (LDR) was 25 - 2500 pg/mL, the limit of detection was 10 pg/mL, and the lower limit of quantification was 25 pg/mL. Intra- and inter-assay error did not exceed 6%. The deviation of the measured sufentanil plasma concentrations between the reanalysis and the first analysis was -63 ± 14% (mean ± SD). Therefore, sufentanil concentrations in human plasma were not stable in samples frozen at -20°C over 11 years.

2,2'-Bipyridyl-4,4'-Dicarboxylic Acid Modified Buried Interface of High-Performance Perovskite Solar Cells.

The regulation of interfaces remains a critical and challenging aspect in the pursuit of highly efficient and stable perovskite solar cells (PSCs). Here, 2,2'-bipyridyl-4,4'-dicarboxylic acid (HBPDC) is incorporated as an interfacial layer between SnO2 and perovskite layers in PSCs. The two carboxylic acid moieties on HBPDC bind to SnO2 through esterification, while its nitrogen atoms, possessing lone electron pairs, interact with uncoordinated lead (Pb2+) atoms through Lewis acid-base interactions. This dual functionality enables simultaneous passivation of surface defects on both the SnO2 and buried perovskite layers. In addition, the electron-deficient nature of HBPDC enhances interfacial energy band alignment and facilitates electron transfer from the perovskite to SnO2. Furthermore, the incorporation of HBPDC strengthens the interfacial adhesion, improving mechanical reliability. As a result, the PSCs exhibited an impressive power conversion efficiency (PCE) of 25.41% under standard AM 1.5G conditions, along with remarkable environmental stability.

A Surface-Reconstructed Bilayer Heterojunction Enables Efficient and Stable Inverted Perovskite Solar Cells.

The efficiency of perovskite photovoltaics remains distant from their theoretical limits, primarily due to high photovoltage losses. Here a strategy is reported to minimize voltage losses by reconstructing the perovskite surface into a bilayer heterojunction (BLH) structure. Unlike conventional low-dimensional capping layers, typically constrained to a few nanometers to prevent low fill factors, this methodology facilitates a more comprehensive reaction with surface defects, allowing a more substantial capping layer (≈50 nanometers) without compromising charge transport integrity. Time-resolved microwave conductivity analysis indicates a significant reduction in trap density at the top region of the perovskite film, showing an order of magnitude lower than that of the pristine sample. Incorporating this BLH in inverted cells results in a remarkably low photovoltage deficit of 325 mV, leading to a power conversion efficiency (PCE) of 26.1% (25.72% certified). The encapsulated device maintains 94% of its original efficiency after 1200 h of maximum power point tracking under one sun illumination at 65 °C.

Assessing the stability of responding of male mice in the touchscreen 5 choice serial reaction time task: Focus on premature responding.

The five-choice serial reaction time task (5CSRTT) is a test of attention that provides a well-validated ancillary measure of impulsive action, measured by premature responses. The task has been adapted for mice in touchscreen operant boxes, which is thought to offer improved test-retest reliability. Few studies have assessed the long-term stability of performance, including premature responding in this version of the task. We used the touchscreen 5CSRTT to conduct longitudinal testing of stability of premature responding following repeated behavioral and pharmacological manipulations. Male C57BL/6J mice were trained on a baseline version of the 5CSRTT. They were then tested on versions of the task in which the stimulus duration was reduced, and inter-trial intervals were elongated or varied within-session. Premature responding was subsequently tested following administration of pharmacological agents known to bi-directionally affect attention and impulsive action-cocaine, atomoxetine, and yohimbine. Mice were lastly re-tested 6 months later using the 5CSRTT with elongated inter-trial intervals. A reduced stimulus duration impacted attention, with reduced accuracy and increased omissions, but had no effect on premature responding. Both elongating and varying the inter-trial interval within-session increased premature responses. Mice showed similar and stable levels of increased premature responding 6 months later. Cocaine increased premature responding, though less than previously reported in rats. Atomoxetine reduced premature responding. Yohimbine had no effect on premature responding in the baseline task but decreased premature responding when tested using an elongated inter-trial interval. Overall, these results highlight that the touch screen adaptation of the 5CSRTT is an effective method for longitudinal testing of attention and impulsive action and remains sensitive to performance changes arising from repeated pharmacological and behavioral challenges.

Evaluation of Long-Term Stability in Single-Piece Implant Systems: An Original Research.

Background: Because of its integrated design and possible benefits over conventional two-piece systems, single-piece implant systems have grown in favor in the field of dental implantology. There is, however, still a dearth of information about their long-term stability and clinical results. The purpose of this study was to assess the clinical results, such as implant survival rates, peri-implant tissue health, and marginal bone levels, to determine the long-term stability of single-piece implant systems. Methods: About 127 individuals who got single-piece implants at the tertiary care center were the subject of a retrospective analysis. Standardized procedures were followed for implant implantation, and patients were monitored for at least five years afterward. Through radiographic analysis and clinical tests, clinical indicators such as marginal bone levels, peri-implant tissue health, and implant survival rates were evaluated. Results: With low marginal bone loss and good peri-implant tissue health, the research showed a high implant survival rate of 96.5%. A statistical study revealed significant relationships between marginal bone loss (P < 0.01), peri-implant tissue health (P < 0.05), and implant survival. Conclusion: In this study, single-piece implant devices showed good long-term durability and clinical results. These results confirm its effectiveness as a dependable dental rehabilitation alternative, highlighting the significance of preserving the health of the peri-implant tissue and reducing marginal bone loss to guarantee implant success.

Impact of storage conditions on the shelf life of aflatoxin biocontrol products containing atoxigenic isolates of Aspergillus flavus as active ingredient applied in various countries in Africa.

Aflatoxin contamination significantly threatens food safety and security, particularly in tropical and sub-tropical regions where staple crops such as maize, groundnut, and sorghum become frequently affected. This contamination is primarily caused by the fungus Aspergillus flavus. The contamination causes adverse health effects, reduced income, and trade restrictions. In response to this challenge, various technologies have been developed to mitigate the impacts of aflatoxin. Among these, biocontrol products containing atoxigenic isolates of A. flavus as the active ingredient can effectively reduce aflatoxin levels both at pre- and post-harvest. A notable example of such products is Aflasafe, which contains four atoxigenic isolates native to specific target regions. These products have undergone rigorous testing, have received regulatory approval, and are commercially available in multiple African countries. However, their manufacturing processes have evolved, and comprehensive shelf life studies for current formulations are lacking. Evaluations of the spore production ability of atoxigenic A. flavus isolates in Aflasafe products over 4 years, under various storage conditions, revealed a significant linear decrease in sporulation with storage months (P < 0.001; R 2 = 0.203), with no significant differences observed between treatments. However, this marginal decline (P = 0.398) is unlikely to be sufficient to prevent the effectiveness in limiting aflatoxin. In addition, storing the products for 2 weeks at 54 °C did not affect (P > 0.05) the ability of the coated fungi to produce spores compared to when the products were stored at 24 °C. The findings contribute valuable insights for manufacturers and users of atoxigenic-based aflatoxin biocontrol products, informing best practices for product storage and utilization to ensure prolonged effectivenes in aflatoxin mitigation efforts.

Adult Herbst-multibracket appliance treatment-how stable are the results very long term?

AIM: To investigate the post-treatment (Tx) changes (≥ 15 years) in adult Class II patients treated with Herbst appliance and subsequently a multibracket appliance (MBA). SUBJECTS AND METHODS: Of 51 potential patients 31 could be located and participated (19 II:1 and 12 II:2). At a mean age of 21.8 ±â€…7.3 years (T0), Herbst-MBA Tx had been started. The mean post-Tx observation period was 19.8 ±â€…3.6 years. Study models from before and after Tx (T1, mean age: 23.6 ±â€…7.4 years), after 3.0 ±â€…2.8 years of retention (T2, mean age: 26.8 ±â€…8.3 years) as well as after recall (T3, mean age: 43.4 ±â€…7.5 years) were evaluated using the PAR index as well as standard occlusal variables. RESULTS: Pre-Tx, the mean values of the 31 participants were: PAR score = 26.1 ±â€…9.6 points, Class II molar relationship (MR) = 0.7 ±â€…0.2 cusp widths (CW), overjet = 6.9 ±â€…2.3 mm and overbite = 4.8 ±â€…2.6 mm. After Tx, the mean PAR score was 5.3 ±â€…2.8. A Class I MR (0.0 ±â€…0.1 CW) was present while overjet and overbite had decreased to 2.1 ±â€…0.7 and 1.3 ±â€…0.8 mm, respectively. At recall (19.8 ±â€…3.6 years post-Tx), a slight PAR score increase (+ 3.1 points) had occurred (final value: 8.4 ±â€…3.7); this was mainly due to mild increases in overjet, overbite (final values: 3.3 ±â€…1.4 mm and 2.5 ±â€…1.7 mm) and changes in sagittal MR (0.2 ±â€…0.2 CW). LIMITATIONS: The sample size and the participation rate as well as the unavailability of a comparable control group can be considered as limitations. In addition, no long-term radiographic data could be obtained, and the retention protocol was not uniform. The majority of these issues, however, should be acceptable to due to the duration of the observation period and the uniqueness of the data. CONCLUSION: In the present sample, Herbst-MBA Tx enabled Class II correction in adults with very good occlusal long-term stability.

Unraveling the Role of Electron-Withdrawing Molecules for Highly Efficient and Stable Perovskite Photovoltaic.

Electron-withdrawing molecules (EWMs) have exhibited remarkable efficacy in boosting the performance of perovskite solar cells (PSCs). However, the underneath mechanisms governing their positive attributes remain inadequately understood. Herein, we conducted a comprehensive study on EWMs by comparing 2,2'-(2,5-cyclohexadiene-1,4-diylidene) bismalononitrile (TCNQ) and (2,3,5,6-tetrafluoro-2,5-cyclohexadiene-1,4-diylidene) dimalononitrile (F4TCNQ) employed at the perovskite/hole transport layer (HTL) interfaces. Our findings reveal that EWMs simultaneously enhance chemical passivation, interface dipole effect, and chemically binding of the perovskite to the HTL. Notably, F4TCNQ, with its superior electron-withdrawing properties, demonstrates a more pronounced impact. Consequently, PCSs modified with F4TCNQ achieved an impressive power conversion efficiency (PCE) of 25.21%, while demonstrating excellent long-term stability. Moreover, the PCE of a larger-area perovskite module (14.0 cm2) based on F4TCNQ reached 21.41%. This work illuminates the multifaceted mechanisms of EWMs at the interfaces in PSCs, delivering pivotal insights that pave the way for the sophisticated design and strategic application of EWMs, thereby propelling the advancement of perovskite photovoltaic technology.

The long-term transformation of FeIII-AsV coprecipitates at room temperature under oxic conditions: New insights for the fate and the speciation of As.

The long-term stability of FeIII-AsV coprecipitates, a typically hydrometallurgical or naturally produced As-bearing wastes in tailings or in other environments, is critical to evaluating the As risk caused by them. A wide pH range, different Fe/As molar ratios, reaction media, and neutralization reagents were considered in order to find the mechanisms controlling the fate of As during the 1640 days of transformation at 25 °C. The results indicated that at pH 4 and 12, As continuously released from the solid phase. The components and their proportions determined the fate of As at pH 4. However, at pH 12, crystalline calcium carbonates (CCA) formed due to the CO2 in the air and this combined with the adsorption capacity of As on the 2-line ferrihydrite controlling the fate of As. If pH changed to 8 and 10, yukonite formed after the release of As. The CCA also appeared in the presence of Ca. Therefore, these two processes controlled the fate of As at this pH range. These findings are important for understanding and predicting the transport of As under various environmental conditions. The technology chosen for As remediation in soils and As removal from waste waters will also be benefit from these results.

The recent advancement of outdoor performance of perovskite photovoltaic cells technology.

Perovskite solar cells achieved a record for power conversion efficiency of over 26 % for single junction cells and 34 % for planar silicon/perovskite tandems. These cells can be manufactured from low-cost materials with low-tech production techniques. As a result, it attracted great attention for future solar technology and multiple performance and stability studies have been reported in research articles. This work summarizes recent (2019-2023) reports on outdoor performance and stability tests of perovskite solar cells and modules in different locations and climate conditions. The review realized that there are limited works on outdoor testing of perovskite solar cells, and found only one year is the maximum long-term outdoor stability reported as at the time this review was conducted. The reports of this review demonstrated that accelerated aging tests of perovskite solar cells under harsh conditions such as elevated temperature, damp heat, and high relative humidity cannot replace realistic outdoor testing. As a result, studying the performance and stability of perovskite solar cells and modules under real outdoor conditions is very important to realize its commercialization.

Ampere-Level Hydrogen Generation via 1000 H Stable Seawater Electrolysis Catalyzed by Pt-Cluster-Loaded NiFeCo Phosphide.

Seawater electrolysis can generate carbon-neutral hydrogen but its efficiency is hindered by the low mass activity and poor stability of commercial catalysts at industrial current densities. Herein, Pt nanoclusters are loaded on nickel-iron-cobalt phosphide nanosheets, with the obtained Pt@NiFeCo-P electrocatalyst exhibiting excellent hydrogen evolution reaction (HER) activity and stability in alkaline seawater at ampere-level current densities. The catalyst delivers an ultralow HER overpotential of 19.7 mV at -10 mA cm-2 in seawater-simulating alkaline solutions, along with a Pt-mass activity 20.8 times higher than Pt/C under the same conditions, while dropping to 8.3 mV upon a five-fold NaCl concentrated natural seawater. Remarkably, Pt@NiFeCo-P offers stable operation for over 1000 h at 1 A cm-2 in an alkaline brine electrolyte, demonstrating its potential for efficient and long-term seawater electrolysis. X-ray photoelectron spectroscopy (XPS), in situ electrochemical impedance spectroscopy (EIS), and in situ Raman studies revealed fast electron and charge transfer from the NiFeCo-P substrate to Pt nanoclusters enabled by a strong metal-support interaction, which increased the coverage of H* and accelerated water dissociation on high valent Co sites. This study represents a significant advancement in the development of efficient and stable electrocatalysts with high mass activity for sustainable hydrogen generation from seawater.

Long-term stability of a PTW 34070 large-area parallel ionization chamber in clinical proton scanning beams.

PURPOSE: In the modeling of beam data for proton therapy planning systems, absolute dose measurements are performed utilizing a Bragg peak chamber (BPC), which is a parallel-plate ionization chamber. The long-term stability of the BPC is crucial for ensuring accurate absolute dose measurement. The study aims to assess the long-term stability of the BPC in clinical proton pencil beam scanning delivery. METHODS: The long-term stability evaluation focused on the BPC-Type 34070 (PTW Freiburg, Germany), utilizing clinical proton scanning beams from December 2022 to November 2023. Monthly investigations were conducted to evaluate the response and cross-calibration factor of the BPC and a reference chamber, employing the spread-out Bragg peak (SOBP) field. Additionally, assessments were made regarding the BPC's response to monoenergetic beams, along with an examination of the impact of polarity and ion recombination on the BPC. RESULTS: The response and cross-calibration factor of the BPC varied up to 1.9% and 1.8%, respectively, while the response of the reference chamber remained within a 0.5% range. The BPC's response to the mono-energetic beams varied up to 2.0% across all energies, demonstrating similar variation trends in both the SOBP field and mono-energetic beams. Furthermore, the variations in polarity and ion recombination effect remained stable within a 0.4% range throughout the year. Notably, the reproducibility of the BPC remained high for each measurement conducted, whether for the SOBP field or mono-energetic beams, with a maximum deviation observed at 0.1%. CONCLUSIONS: The response and cross-calibration factor of the BPC demonstrated significant variations, with maximum changes of 1.9% and 1.8%, respectively. However, the reproducibility of the BPC remained consistently high for each measurement. It is recommended that when conducting absolute dose measurements using a BPC, its response should be compared and corrected against the reference chamber for each measurement.

Heparinized self-healing polymer coating with inflammation modulation for blood-contacting biomedical devices.

The current techniques for antithrombotic coating on blood-contacting biomedical materials and devices are usually complex and lack practical feasibility with weak coating stability and low heparin immobilization. Here, a heparinized self-healing polymer coating with inflammation modulation is introduced through thermal-initiated radical copolymerization of methacrylate esterified heparin (MA-heparin) with methyl methacrylate (MMA) and n-butyl acrylate (nBA), followed by the anchoring of reactive oxygen species (ROS)-responsive polyoxalate containing vanillyl alcohol (PVAX) onto the coating through esterification. The aspirin, which is readily dissolved in the solution of MMA and nBA, is encapsulated within the coating after copolymerization. The copolymerization of MA-heparin with MMA and nBA significantly increases the heparin content of the coating, effectively inhibiting thrombosis and rendering the coating self-healing to help maintain long-term stability. ROS-responsive PVAX and aspirin released in a temperature-dependent manner resist acute and chronic inflammation, respectively. The heparinized self-healing and inflammation-modulated polymer coating exhibits the ability to confer long-term stability and hemocompatibility to blood-contacting biomedical materials and devices. STATEMENT OF SIGNIFICANCE: Surface engineering for blood-contacting biomedical devices paves a successful way to reduce thrombotic and inflammatory complications. However, lack of effectiveness, long-term stability and practical feasibility hinders the development and clinical application of existing strategies. Here we design a heparinized self-healing and inflammation-modulated polymer coating, which possesses high heparin level and self-healing capability to maintain long-term stability. The polymer coating is practically feasible to varied substrates and demonstrated to manipulate inflammation and prevent thrombosis both in vitro and in vivo. Our work provides a new method to develop coatings for blood-contacting biomedical materials and devices with long-term stability and hemocompatibility.

Solidification/stabilization pre-treatment coupled with landfill disposal of heavy metals in MSWI fly ash in China: A systematic review.

The growth in municipal solid waste incineration (MSWI) has resulted in a substantial rise in the production of fly ash in China. It is anticipated that during the "14th Five-Year Plan", the accumulated amount of fly ash stocked and disposed of at landfills will surpass 100 million tons. With the development of the economy and the implementation of garbage classification relevant policies, the pollution characteristics of heavy metal change in spatiotemporal distribution. Solidification/stabilization (S/S) pre-treatment coupled with landfill disposal is the mainstream method for fly ash. This study provides a systematic overview and comparison of the current application status and research on the mechanism of S/S technology, and the long-term stability of solidified/stabilized fly ash is a crucial factor in controlling the risks of landfills. Subsequently, it examines the influencing factors and mechanisms associated with heavy metals leaching under different environmental scenarios (meteorological factors, leachate and acid rain erosion, and carbonation, etc.), and concludes that single stabilization technology is difficult to meet long-term landfill requirements. Finally, the limits of heavy metal leaching toxicity evaluation methods and landfilled fly ash supervision were discussed, and relevant suggestions for future development were proposed. This study can provide theoretical instruction and technical support for the risk control of potential environmental risks of heavy metals in solidified/stabilized fly ash from landfills in China.

Calibration of Aseptic Loosening Simulation for Coatings Osteoinductive Effect.

The risk of aseptic loosening in cementless hip stems can be reduced by improving osseointegration with osteoinductive coatings favoring long-term implant stability. Osseointegration is usually evaluated in vivo studies, which, however, do not reproduce the mechanically driven adaptation process. This study aims to develop an in silico model to predict implant osseointegration and the effect of induced micromotion on long-term stability, including a calibration of the material osteoinductivity with conventional in vivo studies. A Finite Element model of the tibia implanted with pins was generated, exploiting bone-to-implant contact measures of cylindrical titanium alloys implanted in rabbits' tibiae. The evolution of the contact status between bone and implant was modeled using a finite state machine, which updated the contact state at each iteration based on relative micromotion, shear and tensile stresses, and bone-to-implant distance. The model was calibrated with in vivo data by identifying the maximum bridgeable gap. Afterward, a push-out test was simulated to predict the axial load that caused the macroscopic mobilization of the pin. The bone-implant bridgeable gap ranged between 50 µm and 80 µm. Predicted push-out strength ranged from 19 N to 21 N (5.4 MPa-3.4 MPa) depending on final bone-to-implant contact. Push-out strength agrees with experimental measurements from a previous animal study (4 ± 1 MPa), carried out using the same implant material, coated, or uncoated. This method can partially replace in vivo studies and predict the long-term stability of cementless hip stems.

Improving the Long-Term Stability of PbTe-Based Thermoelectric Modules: From Nanostructures to Packaged Module Architecture.

Nanostructured lead telluride PbTe is among the best-performing thermoelectric materials, for both p- and n-types, for intermediate temperature applications. However, the fabrication of power-generating modules based on nanostructured PbTe still faces challenges related to the stability of the materials, especially nanoprecipitates, and the bonding of electric contacts. In this study, in situ high-temperature transmission electron microscopy observation confirmed the stability of nanoprecipitates in p-type Pb0.973Na0.02Ge0.007Te up to at least ∼786 K. Then, a new architecture for a packaged module was developed for improving durability, preventing unwanted interaction between thermoelectric materials and electrodes, and for reducing thermal stress-induced crack formation. Finite element method simulations of thermal stresses and power generation characteristics were utilized to optimize the new module architecture. Legs of nanostructured p-type Pb0.973Na0.02Ge0.007Te (maximum zT ∼ 2.2 at 795 K) and nanostructured n-type Pb0.98Ga0.02Te (maximum zT ∼ 1.5 at 748 K) were stacked with flexible Fe-foil diffusion barrier layers and Ag-foil-interconnecting electrodes forming stable interfaces between electrodes and PbTe in the packaged module. For the bare module, a maximum conversion efficiency of ∼6.8% was obtained for a temperature difference of ∼480 K. Only ∼3% reduction in output power and efficiency was found after long-term operation of the bare module for ∼740 h (∼31 days) at a hot-side temperature of ∼673 K, demonstrating good long-term stability.

Combining distribution modelling and phylogeography to understand present, past and future of an endangered spider.

BACKGROUND: Understanding how endangered species respond to climatic changes is fundamental for their conservation. Due to its restricted geographic range, its sensitivity to the ongoing global warming and its continuing decline, the Southwestern-Alpine endemic wolf spider Vesubia jugorum is currently classified as Endangered in the IUCN Red List. Here, we combined species distribution modelling (SDM) and phylogeographic inference to describe the present, the past and the future of this species in light of the mtDNA genetic structure of extant populations. RESULTS: Phylogenetic and network analyses show a high level of genetic differentiation and a strong genetic structure of the populations, likely explicable by a long history of isolation and survival in separate refugia. The SDM projection into past climatic conditions supports these results by showing a smaller distribution range compared to present, mostly restricted to the Maritime and Ligurian Alps, which possibly served as main refugium. Future forecast shows a significant shift in the bioclimatic range towards higher altitudes and latitudes, with a drastic decrease of habitat suitability in the central and south-eastern parts of the range, with consequent general loss of haplotype diversity. CONCLUSION: SDM and phylogeographic inference support the hypothesis that the current distribution and the genetic structure of the extant populations mirror the survival in situ of Vesubia jugorum across repeated glacial and interglacial phases, in line with the 'long-term stability hypothesis'. Future predictions show a significant shift in the bioclimatic range that V. jugorum will be likely unable to track, with profound impact on its long-term survival and its genetic diversity. Our considerations have implication for conservation genetics, highlighting the pivotal role of the transboundary protected areas of the SW-Alps in promoting conservation efforts for this species.

Highly Sustainable h-BN Encapsulated MoS2 Hydrogen Evolution Catalysts.

Despite the importance of the stability of the 2D catalysts in harsh electrolyte solutions, most studies have focused on improving the catalytic performance of molybdenum disulfide (MoS2) catalysts rather than the sustainability of hydrogen evolution. In previous studies, the vulnerability of MoS2 crystals is reported that the moisture and oxygen molecules can cause the oxidation of MoS2 crystals, accelerating the degradation of crystal structure. Therefore, optimization of catalytic stability is crucial for approaching practical applications in 2D catalysts. Here, it is proposed that monolayered MoS2 catalysts passivated with an atomically thin hexagonal boron nitride (h-BN) layer can effectively sustain hydrogen evolution reaction (HER) and demonstrate the ultra-high current density (500 mA cm⁻2 over 11 h) and super stable (64 h at 150 mA cm⁻2) catalytic performance. It is further confirmed with density functional theory (DFT) calculations that the atomically thin h-BN layer effectively prevents direct adsorption of water/acid molecules while allowing the protons to be adsorbed/penetrated. The selective penetration of protons and prevention of crystal structure degradation lead to maintained catalytic activity and maximized catalytic stability in the h-BN covered MoS2 catalysts. These findings propose a promising opportunity for approaching the practical application of 2D MoS2 catalysts having long-term stability at high-current operation.

Copper Vanadium Oxide Yolk-Shell Microspheres with Excellent Capacitance and Cycling Performance for Electrochromic Supercapacitor.

Vanadium pentoxide (V2O5) is considered a promising material for electrochromic supercapacitors due to its rich color transitions and excellent electrochemical capacity. However, V2O5 exhibits low electrical conductivity, and its volume changes dramatically during charge-discharge cycles, leading to structural collapse and poor long-term cyclability. These issues have hindered the development and application of V2O5. In this study, copper vanadium oxide yolk-shell microspheres (CVO) were synthesized through a one-step solvent heat treatment with an annealing process. With the doping of copper element, the capacitance, conductivity, and cyclic stability of CVO microspheres were significantly enhanced. Subsequently, the sphere-wire network structure was formed by blending Na2V6O16·3H2O nanowires (NVO), resulting in the formation of CVO/NVO composites. The three-dimensional sphere-wire network efficiently facilitates the acquisition of additional redox sites and strengthens the material-to-substrate bonding. Under the combined influence of these favorable factors, CVO/NVO achieved a high specific capacitance of 39.2 mF cm-2, with a capacitance retention of 84% after 7500 cycles at a current density of 0.7 mA cm-2. The fully inorganic solid-state electrochromic supercapacitor (ECSC), assembled on the basis of CVO/NVO, demonstrates a vivid and clearly distinguishable color change (ΔE* = 37). Even more impressive is the energy storage capacity (18.4 mF·cm-2) and the cycling stability (up to 89% retention after 10,000 cycles) exhibited by the devices. These key performances are superior to those of most of the previously reported V2O5-based ECSCs, opening a promising avenue for the development of V2O5-based electrochromic energy storage devices.