Commercial reverse osmosis point-of-use systems in Egypt failed to purify tap water.

This study addresses the heightened global reliance on point-of-use (PoU) systems driven by water quality concerns, ageing infrastructure, and urbanization. While widely used in Egypt, there is a lack of comprehensive evaluation of these systems. We assessed 10 reverse osmosis point-of-use systems, examining physicochemical, bacteriological, and protozoological aspects of tap water (inlets) and filtered water (outlets), adhering to standard methods for the examination of water and wastewater. Results showed significant reductions in total dissolved solids across most systems, with a decrease from 210 ± 23.6 mg/L in tap water to 21 ± 2.8 mg/L in filtered water for PoU-10. Ammonia nitrogen levels in tap water decreased from 0.05 ± 0.04 to 2.28 ± 1.47 mg/L to 0.02 ± 0.04 to 0.69 ± 0.64 mg/L in filtered water. Despite this, bacterial indicators showed no significant changes, with some systems even increasing coliform levels. Protozoological analysis identified prevalent Acanthamoeba (42.5%), less frequent Naegleria (2.5%), Vermamoeba vermiformis (5%), and potentially pathogenic Acanthamoeba genotypes. Elevated bacterial indicators in filtered water of point-of-use systems, combined with essential mineral removal, indicate non-compliance with water quality standards, posing a public health concern. Further research on the long-term health implications of these filtration systems is essential.

A comprehensive assessment of the economic and technical viability of a zero liquid discharge (ZLD) hybrid desalination system for water and salt recovery.

Brine, a by-product of desalination and industrial facilities, is becoming more and more of an environmental issue. This comprehensive techno-economic assessment (TEA), focusing on the technical and economic aspects, investigates the performance and viability of a novel hybrid desalination brine treatment system known as zero liquid discharge (ZLD). Notably, this research represents the first instance of evaluating the feasibility and effectiveness of integrating three distinct desalination processes, namely brine concentrator (BC), high-pressure reverse osmosis (HPRO), and membrane-promoted crystallization (MPC), within a ZLD framework. The findings of this study demonstrate an exceptional water recovery rate of 97.04%, while the energy requirements stand at a reasonable level of 17.53 kWh/m3. Financially, the ZLD system proves to be at least 3.28 times more cost-effective than conventional evaporation ponds and offers comparable cost efficiency to alternatives such as land application and deep-well injection. Moreover, the ZLD system exhibits profitability potential by marketing both drinking water and solid salt or solely desalinated water. The daily profit from the sale of generated water varies from US$194.08 to US$281.41, with Greece and Cyprus attaining the lowest and highest profit, respectively. When considering the sale of both salt and water, the profit rises by 8% across all locations.

Metal-phenolic network as precursor complex coating for forward osmosis membrane with enhanced antifouling property.

In this study, a multi-functional layer was developed based on the commercially available cellulose triacetate (CTA) forward osmosis (FO) membrane to improve its antifouling property. Tannic acid/ferric ion (TA/Fe3+) complexes were firstly coated as a precursor layer on the membrane surface via self-assembly. Afterwards, the tannic acid/diethylenetriamine (TA/DETA) hydrophilic functional layer was further coated, following Ag/polyvinylpyrrolidone (PVP) anti-bacterial layer was formed in situ through the reducibility of TA to obtain TA/Fe3+-TA/DETA-Ag/PVP-modified membrane. The optimized precursor layer was acquired by adjusting the buffer solution pH to 8, TA/Fe3+ ratio to 4 and the number of self-assembled layers to 5. The permeability testing results illustrated that the functional layer had an insignificant effect on the membrane transport parameters. The TA/Fe3+-TA/DETA-Ag/PVP-modified membrane simultaneously exhibited excellent physical and chemical stability. The coated membrane also demonstrated enhanced anti-bacterial properties, achieving 98.63 and 97.30% inhibition against Staphylococcus aureus and Escherichia coli, respectively. Furthermore, the dynamic fouling experiment showed a 12% higher water flux decrease for the TA/Fe3+-TA/DETA-Ag/PVP CTA membrane compared to the nascent CTA membrane, which proved its excellent antifouling performance. This work provides a feasible strategy to heighten the antifouling property of the CTA FO membrane.

Multi-dimensional parametric study for enhancing Brackish Water Reverse Osmosis membrane performance suited for desalination of low salinity feeds.

Reverse osmosis (RO) effectively provides clean drinking water. Different RO membrane types are tailored to treat saline water feeds with varying characteristics. In the context of low brackish water feeds, the objective is to remove only a minimal excess of salinity through the membrane. Our study introduces a method of membrane post-treatments capable of achieving controlled salt rejection while concurrently enhancing permeate flux, which is vital for achieving effective and energy-efficient desalination of low brackish water. The post-treatments were conducted on our in-house-developed membranes using aqueous solutions of N,N-Dimethylformamide and glycerol for different drying times at the coupon level. The process was scaled up at the module level, allowing us to assess its potential for commercial application. At the coupon level, the permeate flux increased significantly from 3.7 ± 0.9 to 10.6 ± 0.2 L/m2·h·bar, while the salt rejection decreased from 95.6 ± 1% to 70.5 ± 1% when measured with a feed of 2,000 ppm NaCl concentration. At the module level, we observed a higher flux of 12.8 L/m2·h·bar, alongside a salt rejection of 55.5% with a similar feed. Varying post-treatment parameters at the coupon level allowed us to attain the desired salt rejection and permeate flux values. Physical changes in both pristine and post-treated membranes, including polymer swelling, were observed without chemical alterations, enhancing our understanding of the post-treatment effect and its potential for broader commercial use. PRACTITIONER POINTS: Post-treatment of RO membranes enhances flux. Physical structuring through polymer swelling was observed with the chemical structure unaltered. Post-treatment of RO opens doors for broader energy-efficient desalination application.

Electroneutralization desalination with spontaneous chemoelectric power generation.

This study designs a novel electroneutralization desalination cell using reaction heat from acidic-alkaline wastewater neutralization to desalinate wastewater and generates chemoelectric power. Several key performance indicators are measured in terms of the energy, environmental and economic aspects of the system, including the ionic flux, the electrical energy produced, the electrical energy consumption for desalination, parasitic losses, overall energy conversion efficiency and desalination performance. The maximum peak power density is ∼31.5 mW/cm2 at 83.5 mA/cm2 and the desalination efficiency is 62 % using brine. The overall energy conversion efficiency is ∼81.8 % and the desalination followed the zero-order reaction. Assuming a 1.5 million litres per day treatment capacity integrated with reverse osmosis, the system has environmental and economic benefits, with 44.5 kg-CO2eq greenhouse gas emissions per cubic meter of treated brine, and a discounted payback period of 4.2 years. This study demonstrates a pioneering electroneutralization technique for self-sufficient brine valorization and wastewater reclamation.

Zinc-loaded mesoporous silica nanoparticles mitigate salinity stress in wheat seedlings through silica-zinc uptake, osmotic balance, and ROS detoxification.

Abiotic stresses like salinity and micronutrient deficiency majorly affect wheat productivity. Applying mesoporous silica nanoparticles (MSiNPs) as a smart micronutrient delivery system can facilitate better stress management and nutrient delivery. In this purview, we investigated the potential of MSiNPs and Zn-loaded MSiNPs (Zn-MSiNPs) on the growth and physiology of wheat seedlings exposed to salinity stress (200 mM NaCl). Initially, the FESEM, DLS, and BET analysis portrayed nanoparticles' spherical shape, nano-size, and negatively charged mesoporous surface. A sustained release of Zn+2 from Zn-MSiNPs at 30 °C, diffused light, and pH 7 was perceived with a 96.57% release after 10 days. Further, the mitigation of NaCl stress in the wheat seedlings was evaluated with two different concentrations, each of MSiNPs and Zn-MSiNPs (1 g/L and 5 g/L), respectively. A meticulous improvement in the germination and growth of wheat seedlings was observed when treated with both MSiNPs and Zn-MSiNPs. A considerable increase in chlorophyll, total protein, and sugar content was in consort with a substantial decline in MDA, electrolyte leakage, and ROS accumulation, showcasing the nanomaterials' palliating effects. Most importantly, the K+/Na+ ratio in shoots increased significantly by 3.43 and 4.37 folds after being treated with 5 g/L Zn-MSiNPs, compared to their respective control sets (0 and 200 mM NaCl). Therefore, it can be concluded that the Zn-MSiNPs can effectively restrain the effects of salinity stress on wheat seedlings.

Desalination RO reject brine as a novel-based porous geopolymer for phosphorus removal from contaminated media.

Desalination reverse osmosis reject brine-based porous geopolymer (RO/GP) was produced and investigated as an improved adsorbent for phosphorus (P) removal from tainted seawater, brackish water, river water, and municipal wastewater effluent. The RO reject brine/geopolymer was produced by reacting metakaolin and fly ash with a Na-alkali activator and anhydrous RO brine as a sacrificial template. The influence of RO reject brine content on water absorption, porosity, mechanical, and structural properties were examined. The developed RO-based geopolymers exhibited the greatest porosity (58.3-84.2 % vol%), a significant ratio of open porosity to total porosity (67.7-92.1 %), and outstanding compression strength (3.6-10.4 MPa). The produced RO/GP structure has an adsorption capacity of 92.4 mg-P/g. The sequestration reaction of phosphorus by RO/GP is of pseudo-second-order kinetic behavior via Chi-squared (χ2), RMSE, and determination coefficient (R2) values. Regarding their agreement with Langmuir behavior, the phosphorus adsorption uptakes occur in homogeneous and monolayer states. The reaction is exothermic, spontaneous, and favorable. The RO/GP exhibits significant affinity for phosphorus co-existing with Cl-, Na+, SO42-, K+, HCO3-, and Ca2+. The RO/GP shows high safety during the adsorption investigation, with a total cost of 0.32 $/kg-P.

A prototype system for the removal of 137Cs from liquid radioactive waste using reverse osmosis membrane.

Cesium removal from aqueous solutions of radioactive waste streams is a challenge in the field of radioactive waste management; this is due to the small atomic radii of Cs+ metal ions and their high migration ability. So, the development of a withstand system for the removal of Cs+ is crucial. In the current study, the removal of radioactive cesium from aqueous solutions using an RO-TLC membrane was studied. Two modifications were conducted; the first is to enlarge the cesium metal ion radii by interacting with mono- and dibasic acids, namely, stearic acid, tartaric acid, citric acid, and EDTA, and the second is the modification of the RO membrane pore size via reaction with the same acids. The modification was confirmed using SEM, FTIR, and EDX analysis techniques. The Cs+ and K+ rejection capacities and water permeability across the membrane at 1.5 bars were evaluated. Along with using the above-mentioned acids, the Cs+ metal ion retention index (RCs) was also obtained. It was found that employing EDTA as a chelating agent in an amount of 1.5 g/L in conjunction with the variation of feed content since it provided the highest value of RCs ~ 98% when used. Moreover, the elution of Cs+ using water, EDTA, ammonia, and HCl is also investigated. The optimal value of the eluent concentration was (0.25 M) HCl. Finally, Langmuir and Freundlich isotherm models were applied for a better understanding of the sorption process. The results of the present work more closely match the Langmuir isotherm model to determine the dominance of the chemical sorption mechanism.

Nanoparticle aggregation and electro-osmotic propulsion in peristaltic transport of third-grade nanofluids through porous tube.

In the modern era, the utilization of electro-kinetic-driven microfluidic pumping procedures spans various biomedical and physiological domains. The present study introduces a mathematical framework for characterizing the hemodynamics of peristaltic blood flow within a porous tube infused with ZrO2 nanoparticles. This model delves into the interactions between buoyancy, electro-osmotic forces, and aggregated nanoparticles to discern their influence on blood flow. We employ a third-grade fluid model to elucidate the rheological behavior of the pseudoplastic fluid which refers to its response to applied shear stress, specifically the relationship between shear rate and viscosity. The collective influence of accommodating heat convection, joule heating and aggregated nanoparticles contributes to the thermal behavior of fluids. The distribution of electric potential within the electric double layer (EDL) is predicted by solving the Poisson-Boltzmann equation. The rescaled equations are simplified using the lubrication and Debye-Hückel models as the underlying frameworks. The novel homotopy perturbation method is employed to obtain solutions for the finalized non-linear partial differential equation. Theoretical assessment of hemodynamic impacts involves plotting graphical configurations for various emerging parameters. As electro-osmotic parameter increase, the bloodstream encounters greater impedance, thereby enhancing the effectiveness of electro-osmotic assistance. Concurrently, elevated convective heat markedly reduces the rate of heat transfer, potentially resulting in a drop in blood temperature. It is important to note that maximum shear stress occurs when the artery is positioned horizontally, underscoring the significant impact of arterial alignment on wall shear stress. Skin friction intensifies with the increasing wall permeability as aggregated nanofluids pass through the arterial conduit. Therefore, aggregation of nanoparticles into the bloodstream yields a broader spectrum of distinctive physiological features. In summary, these findings enable more effective tool and device designs for addressing medication administration challenges and electro-therapies.

Integrated Membrane Process in Organic Media: Combining Organic Solvent Ultrafiltration, Nanofiltration, and Reverse Osmosis to Purify and Concentrate the Phenolic Compounds from Wet Olive Pomace.

Phenolic compounds from a hydroalcoholic extract of wet olive pomace were purified and concentrated by an integrated membrane process in organic media. First, UF010104 (Solsep BV) and UP005 (Microdyn Nadir) membranes were tested to be implemented in the ultrafiltration stage, with the aim of purifying the extract and obtaining a permeate enriched in phenolic compounds. Despite the high flux observed with the UF010104 membrane (20.4 ± 0.7 L·h-1·m-2, at 2 bar), the UP005 membrane was selected because of a more suitable selectivity. Even though some secoiridoids were rejected, the permeate stream obtained with this membrane contained high concentrations of valuable simple phenols and phenolic acids, whereas sugars and macromolecules were retained. Then, the ultrafiltration permeate was subjected to a nanofiltration step employing an NF270 membrane (DuPont) for a further purification and fractionation of the phenolic compounds. The permeate flux was 50.2 ± 0.2 L·h-1·m-2, working at 15 bar. Hydroxytyrosol and some phenolic acids (such as vanillic acid, caffeic acid, and ferulic acid) were recovered in the permeate, which was later concentrated by reverse osmosis employing an NF90 membrane. The permeate flux obtained with this membrane was 15.3 ± 0.3 L·h-1·m-2. The concentrated phenolic mixture that was obtained may have important applications as a powerful antioxidant and for the prevention of diabetes and neurodegenerative diseases.

Bioelectric stimulation controls tissue shape and size.

Epithelial tissues sheath organs and electro-mechanically regulate ion and water transport to regulate development, homeostasis, and hydrostatic organ pressure. Here, we demonstrate how external electrical stimulation allows us to control these processes in living tissues. Specifically, we electrically stimulate hollow, 3D kidneyoids and gut organoids and find that physiological-strength electrical stimulation of ∼ 5 - 10 V/cm powerfully inflates hollow tissues; a process we call electro-inflation. Electro-inflation is mediated by increased ion flux through ion channels/transporters and triggers subsequent osmotic water flow into the lumen, generating hydrostatic pressure that competes against cytoskeletal tension. Our computational studies suggest that electro-inflation is strongly driven by field-induced ion crowding on the outer surface of the tissue. Electrically stimulated tissues also break symmetry in 3D resulting from electrotaxis and affecting tissue shape. The ability of electrical cues to regulate tissue size and shape emphasizes the role and importance of the electrical micro-environment for living tissues.

Impact of temperature and forward osmosis membrane properties on the concentration polarization and specific energy consumption of hybrid desalination system.

This study investigates how temperature and forward osmosis (FO) membrane properties, such as water permeability (A), solute permeability (B), and structural parameter (S), affect the specific energy consumption (SEC) of forward osmosis-reverse osmosis system. The results show that further SEC reduction beyond the water permeability of 3 LMH bar-1 is limited owing to high concentration polarization (CP). Increasing S by 10-fold increases FO recovery by 177.6%, causing SEC decreases by 33.6%. However, membrane with smaller S also increases external CP. To reduce SEC, future work should emphasize mixing strategies to reduce external CP. Furthermore, increasing the temperature from 10 to 40 °C can reduce SEC by 14.3%, highlighting the energy-saving potential of temperature-elevated systems. The factorial design indicates that at a lower temperature, increasing A and decreasing S have a more significant impact on reducing SEC. This underlines the importance of developing advanced FO membranes, particularly for lower-temperature processes.

Textural formation of instant controlled pressure drop-dried peach chips: Investigation of the electrical, thermal, and textural properties of predried peach slices with osmotic dehydration pretreatment.

In this study, the effect of osmotic dehydration (OD) pretreatment with various sugar (erythritol, glucose, and trehalose) on the quality of hot-air-predried peach slices was investigated, particularly focusing on electrical properties, texture, thermal stability, and cell wall strength. Furthermore, the correlation between the properties of predried peach slices and the texture of the instant controlled pressure drop (DIC) dried peach chips was explored. OD pretreatments improved the stability and integrity of the cell wall and cell membrane of pre-dried peach slices, which inhibited the excessive expansion of samples during DIC drying. Especially, peach chips with trehalose-OD exhibited the highest crispiness (1.05 mm), the highest hardness (101.34 N) was obtained in erythritol-OD samples. Overall, the type of osmotic agents affected the texture of DIC peach chips with OD pretreatments. It should be noted that trehalose is a promising osmotic agent for controlling and regulating the quality of DIC peach chips.

Improving antifouling performance of FO membrane by surface immobilization of silver nanoparticles based on a tannic acid: diethylenetriamine precursor layer for municipal wastewater treatment.

In this study, a facile method for multifunctional surface modification on forward osmosis (FO) membrane was constructed by surface immobilization of AgNPs based on tannic acid (TA)/diethylenetriamine (DETA) precursor layer. The cellulose triacetate (CTA) FO membranes modified by TA and DETA with different co-deposition time (6 h, 12 h, 24 h) were investigated. Results indicated that the TA/DETA (24)-Ag CTA membrane with a TA/DETA co-deposition time of 24 h was identified to be optimal, which attained more hydrophilic. And it had the bacterial mortality of Escherichia coli and Staphylococcus aureus reaching 98.23% and 99.83% respectively and possessed excellent physical and chemical binding stability. Meanwhile, the coating layer resulted in the antifouling ability without damaging the membrane intrinsic transport characteristics. As for synthetic municipal wastewater treatment, the water flux of CTA FO membrane decreased approximately 49% of the initial flux after running for 14 days. In contrast, the flux decline rate of TA/DETA (24)-Ag CTA membrane was about 37%. Furthermore, less foulant deposition and higher recovery rate of water flux was observed for TA/DETA (24)-Ag CTA membrane, implying that the modified membrane effectively alleviated membrane fouling and processed a lower flux decline during municipal wastewater treatment. It was attributed to the enhanced surface hydrophilicity and antibacterial property of the coating layer, which improved antifouling property.

Treating reverse osmosis brine of petrochemical wastewater using preparative vertical-flow electrophoresis (PVFE) with multi-objective optimization by response surface method.

Electrochemical desalination is an effective method for recovering salts from reverse osmosis (RO) brine. However, traditional technologies like bipolar membrane technology often face challenges related to membrane blockage. To overcome this issue, a preparative vertical-flow electrophoresis (PVFE) system was used for the first time to treat RO brine of petrochemical wastewater. In order to optimize the PVFE operation and maximize acids and bases production while minimizing energy consumption, the response surface method was employed. The independent variables selected were the electric field intensity (E) and flow rate (v), while the dependent variables were the acid-base concentration and energy consumption (EC) for acid-base production. Using the central composite design methodology, the operation parameters were optimized to be E = 154.311 V/m and v = 0.83 mL/min. Under these conditions, the base concentrations of the produced bases and acids reached 3183.06 and 2231.63 mg/L, respectively. The corresponding base EC and acid EC were calculated to be 12.57 and 11.62 kW·h/kg. In terms of the acid-base concentration and energy consumption during the PVFE process, the electric field intensity was found to have a greater influence than the flow rate. These findings provide a practical and targeted solution for recycling waste salt resources from RO brine.

Removal of multiple pesticides from water by different types of membranes.

Pesticides are used in agriculture to protect crops from pathogens, insects, fungi and weeds, but the release of pesticides into surface/groundwater by agriculture runoff and rain has raised serious concerns not only for the environment but also for human health. This study aimed to investigate the impact of surface properties on the performance of seven distinct membrane types utilized in nanofiltration (NF), reverse osmosis (RO) and forward osmosis (FO) processes in eliminating multiple pesticides from spiked water. Out of the membranes tested, two are self-fabricated RO membranes while the rest are commercially available membranes. Our results revealed that the self-fabricated RO membranes performed better than other commercial membranes (e.g., SW30XLE, NF270, Duracid and FO) in rejecting the targeted pesticides by achieving at least 99% rejections regardless of the size of pesticides and their log Kow value. Despite the marginally lower water flux exhibited by the self-fabricated membrane compared to the commercial BW30 membrane, its exceptional ability to reject both mono- and divalent salts renders it more apt for treating water sources containing not only pesticides but also various dissolved ions. The enhanced performance of the self-fabricated RO membrane is mainly attributed to the presence of a hydrophilic interlayer (between the polyamide layer and substrate) and the incorporation of hydrophilic nanosheets in tuning its surface characteristics. The findings of the work provide insight into the importance of membrane surface modification for the application of not only the desalination process but also for the removal of contaminants of emerging concern.

AnWRKY29 and AnHSP90 synergistically modulate trehalose levels in a desert shrub leaves during osmotic stress.

Trehalose, a biological macromolecule with osmotic adjustment properties, plays a crucial role during osmotic stress. As a psammophyte, Ammopiptanthus nanus relies on the accumulation of organic solutes to respond to osmotic stress. We utilized virus-induced gene silencing technology for the first time in the desert shrub A. nanus to confirm the central regulatory role of AnWRKY29 in osmotic stress, as it controls the transcription of AnTPS11 (trehalose-6-phosphate synthase 11). Further investigation has shown that AnHSP90 may interact with AnWRKY29. The AnHSP90 gene is sensitive to osmotic stress, underscoring its pivotal role in orchestrating the response to such adverse conditions. By directly targeting the W-box element within the AnTPS11 promoter, AnWRKY29 effectively enhances the transcriptional activity of AnTPS11, which is facilitated by AnHSP90. This discovery highlights the critical role of AnWRKY29 and AnHSP90 in enabling organisms to adapt to and cope effectively with osmotic stress, which can be a crucial factor in A. nanus survival and overall ecological resilience. Collectively, uncovering the molecular mechanisms underlying the osmotic responses of A. nanus is paramount for comprehending and augmenting the osmotic tolerance mechanisms of psammophyte shrub plants.

Decreasing incidence of hospital diagnosed CKD/CKDu in North Central Province of Sri Lanka: is it related to provision of drinking water reverse osmosis plants?

BACKGROUND: We assessed the possible impact of provision of reverse osmosis (RO) water on the incidence of hospital diagnosed CKD/CKDu in North Central Province (NCP) of Sri Lanka. METHODS: An ecological study was conducted on data from 2010-2020 on the incidence of hospital diagnosed CKD/CKDu, CKD/CKDu screening and provision of drinking water RO plants in NCP. Analysis was conducted using descriptive statistics, ANOVA and chi-square test. RESULTS: The annual incidence of hospital diagnosed CKD/CKDu (per 100 000 population) in 2010-2013, 2014-2016 and 2017-2020 periods in Anuradhapura district were 129.07, 331.06 and 185.57 (p = 0.002) while in Polonnaruwa district these were 149.29, 326.12 and 296.73 (p = 0.04) respectively. In NCP provision of RO plants commenced after 2011 and the decline in the incidence of hospital diagnosed CKD/CKDu was seen in 25 of the 29 Divisional Secretary Divisions when more than 20% of the families received access to drinking RO water projects. CONCLUSIONS: The annual incidence of hospital diagnosed CKD/CKDu increased in NCP from 2010 to 2016 and continuously decreased thereafter. Continuous declining of CKD/CKDu incidence was seen after more than 20% of the families received access to drinking water RO plants.

Effect of titanium oxide/reduced graphene (TiO2/rGO) addition onto water flux and reverse salt diffusion thin-film nanocomposite forward osmosis membranes.

Thin-film nanocomposite (TFN) forward osmosis (FO) membranes have attracted significant attention due to their potential for solving global water scarcity problems. In this study, we investigate the impact of titanium oxide (TiO2) and titanium oxide/reduced graphene (TiO2/rGO) additions on the performance of TFN-FO membranes, specifically focusing on water flux and reverse salt diffusion. Membranes with varying concentrations of TiO2 and TiO2/rGO were fabricated as interfacial polymerizing M-phenylenediamine (MPD) and benzenetricarbonyl tricholoride (TMC) monomers with TiO2 and its reduced graphene composites (TiO2/rGO). The TMC solution was supplemented with TiO2 and its reduced graphene composites (TiO2/rGO) to enhance FO performance and reverse solute flux. All MPD/TMC polyamide membranes are characterized using various techniques such as scanning electron microscopy (SEM), atomic force microscopy (AFM), and contact angle measurements. The results demonstrate that incorporating TiO2/rGO into the membrane thin layer improves water flux and reduces reverse salt diffusion. In contrast to the TFC membrane (10.24 L m-2h-1 and 6.53 g/m2 h), higher water flux and higher reverse solute flux were detected in the case of TiO2and TiO2/rGO-merged TFC skin membranes (18.81 and 24.52 L m-2h-1 and 2.74 and 2.15 g/m2 h, respectively). The effects of TiO2 and TiO2/rGO stacking on the skin membrane and the performance of TiO2 and TiO2/rGO skin membranes have been thoroughly studied. Additionally, being investigated is the impact of draw solution concentration.

Enhanced water treatment performance of ceramic-based forward osmosis membranes via MOF interlayer.

Forward osmosis (FO) membrane processes could operate without hydraulic pressures, enabling the efficient treatment of wastewaters with mitigated membrane fouling and enhanced efficiency. Designing a high-performance polyamide (PA) layer on ceramic substrates remains a challenge for FO desalination applications. Herein, we report the enhanced water treatment performance of thin-film nanocomposite ceramic-based FO membranes via an in situ grown Zr-MOF (UiO-66-NH2) interlayer. With the Zr-MOF interlayer, the ceramic-based FO membranes exhibit lower thickness, higher cross-linking degree, and increased surface roughness, leading to higher water flux of 27.38 L m-2 h-1 and lower reverse salt flux of 3.45 g m-2 h-1. The ceramic-based FO membranes with Zr-MOF interlayer not only have an application potential in harsh environments such as acidic solution (pH 3) and alkaline solution (pH 11), but also exhibit promising water and reverse salt transport properties, which are better than most MOF-incorporated PA membranes. Furthermore, the membranes could reject major species (ions, oil and organics) with rejections ＞94 % and water flux of 22.62-14.35 L m-2 h-1 in the treatment of actual alkaline industrial wastewater (pH 8.6). This rational design proposed in this study is not only applicable for the development of a high-quality ceramic-based FO membrane with enhanced performance but also can be potentially extended to more challenging water treatment applications.