Adsorption parameters optimization of spent coffee ground biochar for methylene blue removal using response surface methodology.

This study investigates the potential of spent coffee ground biochar (SCGB) as a sustainable and cost-effective adsorbent for the removal of methylene blue (MB), a hazardous dye commonly used in the textile and printing industries. A response surface methodology (RSM) approach with central composite design (CCD) was employed to systematically investigate the effects of key process parameters, including adsorbent dosage, solution pH, contact time and temperature, on MB removal efficiency. The analysis revealed that adsorbent dosage and temperature as critical factors influencing MB removal, with a linear model providing a strong correlation. Optimal conditions for MB removal were determined to be 0.99 g of SCGB, 30 min of contact time, 30 °C temperature, and a solution pH of 7. Under these conditions, MB removal reached 99.99%, with a desirability of 1.000. The experimental results closely matched the predicted values, differing by only 0.02%, thus validating the accuracy of the model. Kinetic studies indicated a rapid adsorption process, well-described by both pseudo-first and pseudo-second order models. Isotherm analysis confirmed the applicability of the Freundlich model, suggesting favorable adsorption with increasing MB concentration. The high adsorption capacity of SCGB is attributed to its carbonaceous and porous structure, highlighting its potential as an effective adsorbent for dye removal in wastewater treatment applications.

Synthesis of novel composite material with spent coffee ground biochar and steel slag zeolite for enhanced dye and phosphate removal.

Rising concerns over water scarcity, driven by industrialization and urbanization, necessitate the need for innovative solutions for wastewater treatment. This study focuses on developing an eco-friendly and cost-effective biochar-zeolite composite (BZC) adsorbent using waste materials-spent coffee ground biochar (CGB) and steel slag zeolite (SSZ). Initially, the biochar was prepared from spent coffee ground, and zeolite was prepared from steel slag; their co-pyrolysis resulted in novel adsorbent material. Later, the physicochemical characteristics of the BZC were examined, which showed irregular structure and well-defined pores. Dye removal studies were conducted, which indicate that BZC adsorption reach equilibrium in 2 h, exhibiting 95% removal efficiency compared to biochar (43.33%) and zeolite (74.58%). Moreover, the removal efficiencies of the novel BZC composite toward dyes methyl orange (MO) and crystal violet (CV) were found to be 97% and 99.53%, respectively. The kinetic studies performed with the dyes and phosphate with an adsorbent dosage of 0.5 g L-1 suggest a pseudo-second-order model. Additionally, the reusability study of BZC proves to be effective through multiple adsorption and regeneration cycles. Initially, the phosphate removal remains high but eventually decreases from 92% to 70% in the third regeneration cycle, highlighting the robustness of the BZC. In conclusion, this study introduces a promising, cost-effective novel BZC adsorbent derived from waste materials as a sustainable solution for wastewater treatment. Emphasizing efficiency, reusability, and potential contributions to environmentally conscious water treatment, the findings highlight the composite's significance in addressing key challenges for the removal of toxic pollutants from the aqueous solutions. PRACTITIONER POINTS: A novel biochar-zeolite composite (BZC) material has been synthesized. Excellent removal of dyes by BZC (~95%) was achieved as compared to their counterparts The kinetic studies performed suggest a pseudo-second-order model. BZC proves to be highly effective for multiple adsorption studies. Excellent reusability showed potential as a robust adsorbent.

Efficient removal of direct dyes by SA-Er biopolymer gel spheres: Equilibrium isotherms, kinetics and regeneration performance study.

Biomass-based adsorbent materials are characterized by their low cost, environmental friendliness, and ease of design and operation. In this study, biomass-based hydrogel microspheres erbium alginate (SA/Er) with high stability and adsorption properties were prepared by a one-step synthesis method. The prepared materials were characterized and analyzed by SEM-EDS, XRD, TGA, FT-IR, UV-Vis, BET-BJH and XPS, and the adsorption performance of SA/Er was investigated for high concentrations of azo dyes in water. The results showed that the adsorption performance of SA/Er on the azo dyes of direct violet N (DV 1) and direct dark green NB (DG 6) with concentrations of 850 mg/L and 1100 mg/L under the optimal conditions was very high, and the adsorption amount could be up to 692 mg/g and 864 mg/g, respectively. The adsorption process was in accordance with the quasi-secondary kinetic model, which was accomplished by physical and chemical adsorption; the Langmuir isothermal model was able to better respond to the adsorption equilibrium, and the adsorption was dominated by the adsorption of surface monolayers; after seven desorption cycles, the removal of both azo dyes by the adsorbent material could reach >79.7 %. Combined with the results of FT-IR, UV-vis and XPS analysis before and after the adsorption, it was revealed that the adsorption of SA/Er with the dye molecules mainly consisted of hydrogen bonding, electrostatic adsorption and surface complexation, which resulted in the significant adsorption effect on the two azo dyes, and the above results can provide a reference for the treatment of dye wastewater.

Efficient adsorption of cationic dyes by a novel honeycomb-like porous hydrogel with ultrahigh mechanical property.

The optimization of hydrogel structure is crucial for adsorption capacity, mechanical stability, and reusability. Herein, a chitosan and laponite-XLS co-doped poly(acrylic acid-co-acrylamide) hydrogel (CXAA) with honeycomb-like porous structures is synthesized by cooperative cross-linking of 2-hydroxypropyltrimethyl ammonium chloride chitosan (HACC) and laponite-XLS in reticular frameworks of acrylic acid (AAc) and acrylamide (AM). The CXAA exhibits extraordinary mechanical performances including tough tensile strength (3.36 MPa) and elasticity (2756 %), which facilitates recycling in practical adsorption treatment and broadens potential applications. Since the regular porous structures can fully expose numerous adsorption sites and electronegative natures within polymer materials, CXAA displays efficient and selective adsorption properties for cationic dyes like methylene blue (MB) and malachite green (MG) from mixed pollutants and can reach record-high values (MB = 6886 mg g-1, MG = 11,381 mg g-1) compared with previously reported adsorbents. Therefore, CXAA exhibits promising potential for separating cationic and anionic dyes by their charge disparities. Mechanism studies show that the synergistic effects of HACC, laponite-XLS, and functional groups in monomers promote highly efficient adsorption. Besides, the adsorption capacity of CXAA remains stable even after undergoing five cycles of regeneration. The results confirm that CXAA is a promising adsorbent for effectively removing organic dyes in wastewater.

Machine learning based-model to predict catalytic performance on removal of hazardous nitrophenols and azo dyes pollutants from wastewater.

To maintain human health and purity of drinking water, it is crucial to eliminate harmful chemicals such as nitrophenols and azo dyes, considering their natural presence in the surroundings. In this particular research study, the application of machine learning techniques was employed in order to make an estimation of the performance of reduction catalysis in the context of ecologically detrimental nitrophenols and azo dyes contaminants. The catalyst utilized in the experiment was Ag@CMC, which proved to be highly effective in eliminating various contaminants found in water, like 4-nitrophenol (4-NP). The experiments were carefully conducted at various time intervals, and the machine learning procedures used in this study were all employed to forecast catalytic performance. The evaluation of the performance of such algorithms were done by means of Mean Absolute Error. The noteworthy findings of this research indicated that the ADAM and LSTM algorithm exhibited the most favourable performance in the case of toxic compounds i.e. 4-NP. Moreover, the Ag@CMC catalyst demonstrated an impressive reduction efficiency of 98 % against nitrophenol in just 8 min. Thus, based on these compelling results, it can be concluded that Ag@CMC works as a highly effective catalyst for practical applications in real-world scenarios.

Development of banana pseudo stem cellulose fiber based magnetic nanocomposite as an adsorbent for dye removal.

A hybrid hydrogel nanocomposite derived from cellulose fiber extracted from Banana Pseudo Stem (BPS) was developed as an adsorbent material for wastewater treatment. The hydrogel was developed by graft copolymerization of N-hydroxyethylacrylamide on Cellulose Fiber (BPSCF-g-PHEAAm) with potassium peroxodisulphate (KPS) as an initiator and N, N'-methylene bisacrylamide (MBA) as a crosslinker using microwave irradiation. Magnetic nanoparticles generated by an in-situ method were incorporated into the network structure. Fourier Transform Infrared Spectroscopy (FTIR), Powder X-ray Diffraction (XRD), Thermogravimetric analysis (TGA), Vibrating Sample Magnetometer (VSM), Brunauer-Emmett-Teller analysis (BET), Field Emission Scanning Electron Microscopy (FESEM), and Energy Dispersive Spectrometer (EDS) were employed. The adsorption capacities of hydrogel and its nanocomposite were evaluated using Methylene Blue (MB) and Crystal Violet (CV) as model dyes. The parent gel exhibited the maximum absorption capacity of 235, and 219 mg g-1 towards MB and CV respectively which was enhanced to 320 and 303 mg g-1 for the nanocomposite. Adsorption data were best fitted with the pseudo-second-order kinetic model and the Freundlich isotherm model. Negative ΔG° and positive ΔH° indicated spontaneous and endothermic adsorption. Desorption was effective to an extent of 99 % in the HCl medium suggesting high reusability potential of the developed adsorbent material.

Preparation of silver-based metal-organic framework and chitosan hybrid material for removing drug and dye.

Pharmaceuticals and personal care products and dyes have low biodegradability and high toxicity, seriously threaten the human health and ecological environment. Therefore, seeking effective removal methods has become the focus of research. In this study, silver-based metal-organic framework (Ag-MOF) and chitosan (CS) hybrid adsorbent (Ag-MOF-CS) was synthesized via solvothermal one-pot synthesis to remove diclofenac sodium (DCF) and acid Red 1 (AR1) from water for the first time. The morphology and structure of Ag-MOF-CS were confirmed by various characterizations. The effect on adsorption was investigated by changing the adsorbent dosage, pH and other conditions. The adsorption kinetics, adsorption isotherms and thermodynamics were analyzed. Ag-MOF-CS showed a high adsorption capacity. And the maximum adsorption capacity of Ag-MOF-CS for DCF and AR1 was 351.75 mg/g and 678.83 mg/g, respectively. The adsorbent bound to DCF and AR1 may via electrostatic forces, π-π interactions, hydrogen bonding. Even after four cycles of Ag-MOF-CS, the DCF removal can still be higher than 80 %. The eco-friendly Ag-MOF-CS demonstrated significant potential for utilization in treating wastewater.

High adsorption capacities for dyes by a pH-responsive sodium alginate/sodium lignosulfonate/carboxylated chitosan/polyethyleneimine adsorbent.

Dyes are indispensable for the rapid development of society, but untreated dye wastewater can threaten human health. In this study, an adsorbent (SA/SL/CCS/PEI@MNPs) was synthesized by one-pot method using magnetic nanoparticles (MNPs), sodium alginate (SA), sodium lignosulfonate (SL), carboxylated chitosan (CCS) and polyethyleneimine (PEI). The adsorbent was mesoporous micrometer-sized particles with pore size of 34.92 nm, which was favorable for dynamic column experiments. SA/SL/CCS/PEI@MNPs possessed pH-responsive performance. Under acidic condition, the maximum adsorption capacities for anionic dyes (tartrazine, reactive black-5, indigo carmine) reached >550 mg/g. Under alkaline condition, those for cationic dyes (methylene blue, methyl violet, neutral red) exceeded 1900 mg/g. The function of the various modifiers was investigated. The results indicated that the incorporation of SL, CCS and PEI was able to provide plenty of sulfonate, carboxylate and amino/imine reactive groups so that adsorption capacities of dyes were improved. The adsorption mechanism was explored by FTIR and XPS. At the same time, the adsorption mechanism was more deeply analyzed using molecular dynamics simulations and radial distribution function. It was demonstrated that the dyes adsorption on the SA/SL/CCS/PEI@MNPs was mainly due to electrostatic attraction and π-π interaction. In addition, the adsorbent had good reusability, and the removal still reached over 90 % after five cycles. In conclusion, the adsorbent displayed a broad prospect for the adsorption of organic dyes.

Lanthanum hydroxide@cellulose membranes with tunable pore sizes for selective removal of dyes with the same charges.

Adsorptive membranes for the efficient separation of dyes with the same charges are quite desirable. Herein, a novel membrane of lanthanum hydroxide/cellulose hydrogel coated filter paper (LC) was prepared through a facile strategy of dip-coating followed by freeze-shaping. With the aid of cellulose gel, the generated La(OH)3 achieved fine dispersion. In addition, the pore size of LC membrane could be regulated by altering the cellulose concentration or the lanthanum chloride dosage, which was crucial for its water flux. In particular, the obtained membrane possessed a high water flux (128.4 L m-2 h-1) and a high dye rejection (97.2 %) for anionic Congo red (CR) only driven by the gravity, which outperformed many previously reported membranes. More intriguingly, its dye rejection for anionic methyl orange (MO) was only 0.9 %, exhibiting high selectivity for dyes with the same charges. Single-solute adsorption experiments indicated that the CR adsorption on the membrane was best fitted by the pseudo-first-order kinetic model, and it followed the Langmuir monolayer adsorption mechanism.

A strategy for the efficient removal of acidic and basic dyes in wastewater by organophilic magadiite@alginate beads: Box-Behnken Design optimization.

In this study, four adsorbents were developed: layered silicate magadiite material (mag), Hexadecyltrimethylammonium intercalated magadiite (HDTMA@mag), a cross-linked composite of sodium alginate and magadiite (ALG@mag) and a cross-linked composite of sodium alginate and HDTMA@magadiite (ALG@HDTMA@mag). The adsorbents were evaluated for their effectiveness in removing of Methylene Blue (MB) and Eriochrome Black T (EBT) dyes. The prepared adsorbents were characterized using SEM, XRD, FTIR, and zeta potential measurements. Kinetic modeling results indicated that both film diffusion and intraparticle diffusion are useful as rate-determining processes in adsorption for all adsorbents. For both dyes, the Langmuir isotherm model provided a good correlation with the adsorption equilibrium data. ANOVA analysis for the best adsorbent (ALG@HDTMA@mag beads) revealed that MB removal was significantly influenced by the positive individual effects of contact time and ALG@HDTMA@mag dose. However, the individual effect of MB concentration exhibited an antagonistic effect throughout the adsorption process. The optimal parameters for achieving an adsorption capacity of 118.54 mg/g were a dye concentration of 60 ppm, a contact period of 1800 min, and an ALG@HDTMA@mag dose of 50 mg.

Optimization of Extraction Conditions from Gac Fruit and Utilization of Peel-Derived Biochar for Crystal Violet Dye Removal.

Gac fruit (Momordica cochinchinensis Spreng.) is a prominent source of carotenoids, renowned for its exceptional concentration of these compounds. This study focuses on optimizing the extraction of active components from the aril of gac fruit by evaluating the effects of extraction temperature, solid-liquid ratio, and extraction time. The primary objective is to maximize the yield of gac oil while assessing its antioxidant capacity. To analyze the kinetics of the solid-liquid extraction process, both first-order and second-order kinetic models were employed, with the second-order model providing the best fit for the experimental data. In addition, the potential of gac fruit peel as a precursor for biochar production was investigated through carbonization. The resultant biochars were evaluated for their efficacy in adsorbing crystal violet (CV) dye from aqueous solutions. The adsorption efficiency of the biochars was found to be dependent on the carbonization temperature, with the highest efficiency observed for BCMC550 (91.72%), followed by BCM450 (81.35%), BCMC350 (78.35%), and BCMC250 (54.43%). The adsorption isotherm data conformed well to the Langmuir isotherm model, indicating monolayer adsorption behavior. Moreover, the adsorption kinetics were best described by the pseudo-second-order model. These findings underscore the potential of gac fruit and its byproducts for diverse industrial and environmental applications, highlighting the dual benefits of optimizing gac oil extraction and utilizing the peel for effective dye removal.

Sodium lignosulfonate as an extracting agent of methylene blue dye using a polymer-enhanced ultrafiltration technique.

The purpose of this research was to evaluate the efficacy of sodium lignosulfonate (LS) as a dye adsorbent in the removal of methylene blue (MB) from water by polymer-enhanced ultrafiltration. Various parameters were evaluated, such as membrane molecular weight cut-off, pH, LS dose, MB concentration, applied pressure, and the effect of interfering ions. The results showed that the use of LS generated a significant increase in MB removal, reaching an elimination of up to 98.0 % with 50.0 mg LS and 100 mg L-1 MB. The maximum MB removal capacity was 21 g g-1 using the enrichment method. In addition, LS was reusable for up to four consecutive cycles of dye removal-elution. The removal test in a simulated liquid industrial waste from the textile industry was also effective, with a MB removal of 97.2 %. These findings indicate that LS is highly effective in removing high concentrations of MB dye, suggesting new prospects for its application in water treatment processes.

Rapid eco-friendly selective dye removal using modified chitosan-based sponges: Synthesis, characterization, and application.

The ongoing challenge of water scarcity persists alongside a concerning rise in water pollution driven by population expansion and industrial development. As a result, urgent measures are imperative to address the pressing need for a clean and sustainable water supply. In this study, a sustainable and green approach was utilized to prepare four chitosan-based sponges from a chemically modified chitosan with different alkyl chains in aqueous medium and at room temperature. The resulting sponges displayed excellent stability in water with outstanding dye removal efficiency. The adsorption capacity was associated with the alkyl chain length incorporated to the polymer backbone. All sponges displayed a high adsorption capacity of methyl orange (MO) ranges between 238 and 380 mg g-1, while a low capacity were obtained for methylene blue (MB) and Rhodamine B (RB). Competitive adsorption experiments were conducted on binary and ternary mixtures to assess the selective removal of MO from a mixture of dyes in which the separation factor was found to be ranging between 1.6 and 32. The adsorption kinetics isotherms of all sponges followed the pseudo-second-order, and the Langmuir model was found to be more suitable than the Freundlich for the adsorption of MO on the sponges. The chitosan-based sponges showed stable performance, robustness and reusability over 5 adsorption-desorption cycles, indicating their great potential for water treatment applications.

Isolation of chitosan and hydroxyapatite from waste edible white garden snail shells and their sensing applications towards industrial Congo red dye detection: Greener approach.

Biomaterials like chitosan, hydroxyapatite have been used in biomedical and pharmaceutical field, due to its valuable biochemical and physiological properties. In current work firstly our group has isolated a polysaccharide chitosan along with hydroxyapatite biomaterial from the same source by varying the process condition via greener approach. We have adapted greener approach for the isolation of chitosan within a short period of time and this is the very first report for the isolation of both chitosan and hydroxyapatite simultaneously from the same waste edible garden snail shells. Both these materials were thoroughly characterized by using UV, FT-IR, SEM techniques. Among synthetic colourants, congo red dye is recognized as carcinogens, which are usually used in the textile manufacturing. Interestingly, one of our biomaterial hydroxyapatite has shown good selectivity towards Congo red dye. The sensitivity range was obtained from 10 to 100 µM within the LOD of 101.52 nM. The developed sensor has been tested for various industrial effluents and shown good agreement with our results. Meanwhile these chitosan and hydroxyapatite have also been used as capping agent for the preparation of stable gold nanoparticles.

Efficient removal of cationic dyes using lemon peel-chitosan hydrogel composite: RSM-CCD optimization and adsorption studies.

The most prominent and easily identifiable factor of water purity is its colour, which may be both physically undesirable, and act as an alert towards potential environmental contamination. The current study describes the optimum synthesis technique for Lemon Peel-Chitosan hydrogel using the Response Surface Methodology integrated Central composite Design (RSM-CCD). This adsorbent is both environmentally friendly and cost-effective. The hydrogel exhibited a maximal dye removal capacity of 24.984, 24.788, 24.862, 23.483, 24.409, and 24.726 mg g-1, for 10 mg L-1 aqueous medium of Safranin O, Methylene blue, Basic fuchsin, Toluidine blue, Brilliant green and Crystal violet, respectively. The adsorption kinetics and isotherm data suggest that the Pseudo second-order kinetic and Freundlich adsorption isotherm models precisely represent the respective behaviour of all the dyes. The thermodynamic viability of the process is determined by the values of ΔG, ΔH, and ΔS. The probable mechanism of adsorption was the electrostatic interaction between the dye molecules and the hydrogel. The regenerated hydrogel had removal efficiencies of over 80 % even after enduring six cycles. Hence, the exceptional recyclability and utility of the adsorbent show their sustainability for wastewater treatment in textile factories.

Lignin: A valuable and promising bio-based absorbent for dye removal applications.

The importance of environmental issues and the existence of humans have led to the recognition of environmental concerns as the main risk to modern life. Notably, one major concern for protecting and managing the environment and human health is the presence of dyes in wastewater. Therefore, before discharging wastewater into mainstream water, it is crucial to remove dyes. Among all lignocellulosic materials, lignin is a highly fragrant biopolymer. Its abundant availability, complex structure, and numerous functional moieties, including hydroxyl, carboxyl, and phenolic, are used in different chemicals and applications. Based on this, lignin is a very useful green material for adsorption, specifically in removing both heavy metals and organic pollutants from wastewater. This article describes the use of lignin-based adsorbents as a recent breakthrough in the removal of dye from aqueous solutions. On the other hand, the review intends to encourage readers to study both established and novel avenues in lignin-based dye removal materials.

Fabrication of carboxymethyl cellulose/graphene oxide/ZnO composite hydrogel for efficient removal of fuchsin dye from aqueous media.

Hydrogels are hydrophilic, insoluble, and highly porous 3D networks capable of absorbing large amounts of water. This study aimed to develop a carboxymethyl cellulose/graphene oxide (CMC/GO) hydrogel, cross-linked with citric acid and modified with zinc oxide (ZnO) nanoparticles (CMC/GO/ZnO), synthesized via the sol-gel method. The formulated composite hydrogel samples were characterized by Fourier transmittance infrared spectroscopy (FTIR), scanning electron microscopy (SEM) analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermo-gravimetric analysis (TGA). The hydrogels were tested for the adsorption of basic fuchsin (BF) dye from the aqueous medium under various conditions, such as adsorbent dosage, contact time, pH, and temperature, using batch adsorption. The adsorption data best fit the Langmuir and Temkin models, with maximum adsorption capacity (qmax) of 172.41 mg/g for CMC/GO and 303.03 mg/g for CMC/GO/ZnO. Optimal adsorption occurred at pH = 6 and within 30 min. The process followed a pseudo-second-order kinetic model, and thermodynamic results indicated that the adsorption process is physical, endothermic and spontaneous. The COOH groups in the hydrogels enhanced affinity for cationic dyes through hydrogen bonding and electrostatic interactions. Thus, CMC/GO and CMC/GO/ZnO hydrogels are efficient and promising adsorbents for environmental remediation.

Novel composite from chitosan and a metal-organic framework for removal of tartrazine dye from aqueous solutions; adsorption isotherm, kinetic, and optimization using Box-Benkhen design.

Cosmetics, textiles, foodstuffs, and medicines frequently contain the yellow dye tartrazine. It has carcinogenic properties and can trigger allergies. In this study, a unique NH2-MIL-101(Cr)/chitosan composite (MIL/chitosan composite) was created using a hydrothermal process. The effectiveness of this composite in removing Tartrazine (TZ) from aqueous solutions was investigated. It was characterized via FT-IR, XPS, XRD, and BET analysis. The surface area of the MIL/chitosan nanoadsorbent sample was 1256.64 m2/g, where after five times recycling, it was reduced to 1068.14 m2/g. The study analyzed the impact of dye concentration, pH, temperature, and MIL/chitosan composite dosage. Experimental measurements were taken for the equilibrium isotherms of dye adsorption. The kinetic models and adsorption isotherm were used to analyze the results. The adsorption process was found to match Langmuir and pseudo-second-order kinetic models. Chemisorption was the mechanism of the adsorption process. Based on thermodynamic parameters, it was determined that the adsorption process was endothermic. The MIL/chitosan composite was recycled up to five cycles. Using the MIL/chitosan composite towards the adsorption of the tartrazine from the real sample has been checked. The interaction process between the MIL/chitosan nanoadsorbent and Tartrazine adsorbate has been investigated. The TZ electrical characteristics, reactivity, and shape were ascertained through the application of density functional theory (DFT). The placement of electrophilic and nucleophilic attack sites is in good agreement with the molecular orbitals (HOMO and LUMO) and MEP results, according to DFT. The optimization of adsorption results was accomplished using Box-Behnken design (BBD).

pH-triggered polydopamine-decorated nanocellulose membranes for continuously selective separation of organic dyes.

Membrane separation technology has emerged as a powerful tool to separate organic dyes from industrial wastewater. However, continuously selective separation of organic dyes with similar molecular weight remains challenging. Herein, we presented a pH-triggered membrane composed of polydopamine-decorated tunicate-derived cellulose nanofibers (PDA@TCNFs) for selective separation of organic dyes. Such self-supporting membranes with nanoporous structure were fabricated by facile vacuum-assisted filtration of PDA@TCNF suspension. The incorporation of polydopamine not only enhanced the stability of the membranes, but also endowed membranes with excellent pH sensitivity, facilitating the continuously selective separation of organic dyes. These pH-triggered PDA@TCNF membranes could selectively separate Methyl Orange (MO) and Rhodamine B (RB) from the MO/RB mixed solution by switching the pH values. The continuously selective separation of the MO/RB mixed solution was demonstrated, where both MO and RB recovery ratios maintained at ∼99 % during 50 repeated cycles. This work provides a new strategy to develop a pH-triggered sustainable nanocellulose-based membrane for continuously selective separation of mixed dyes.

Sodium alginate-encapsulated nano-iron oxide coupled with copper-based MOFs (Cu-BTC@Alg/Fe3O4): Versatile composites for eco-friendly and effective elimination of Rhodamine B dye in wastewater purification.

This study explores the effectiveness of Alginate-coated nano­iron oxide combined with copper-based MOFs (Cu-BTC@Alg/Fe3O4) composites for the sustainable and efficient removal of Rhodamine B (RhB) dye from wastewater through adsorption and photocatalysis. Utilizing various characterization techniques such as FTIR, XRD, SEM, and TEM, we confirmed the optimal synthesis of this composite. The composites exhibit a significant surface area of approximately 160 m2 g-1, as revealed by BET analysis, resulting in an impressive adsorption capacity of 200 mg g-1 and a removal efficiency of 97 %. Moreover, their photocatalytic activity is highly effective, producing environmentally friendly degradation byproducts, thus underlining the sustainability of Cu-BTC@Alg/Fe3O4 composites in dye removal applications. Our investigation delves into kinetics and thermodynamics, revealing a complex adsorption mechanism influenced by both chemisorption and physisorption. Notably, the adsorption kinetics indicate equilibrium attainment within 100 min across all initial concentrations, with the pseudo-second-order kinetic model fitting the data best (R2 ≈ 0.999). Furthermore, adsorption isotherm models, including Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich, elucidate the adsorption behavior, with the Temkin and Dubinin-Radushkevich models showing superior accuracy compared to the Langmuir model (R2 ≈ 0.98 and R2 ≈ 0.96, respectively). Additionally, thermodynamic analysis reveals a negative Gibbs free energy value (-6.40 kJ mol-1), indicating the spontaneity of the adsorption process, along with positive enthalpy (+24.3 kJ mol-1) and entropy (+82.06 kJ mol-1 K) values, suggesting an endothermic and disorderly process at the interface. Our comprehensive investigation provides insights into the optimal conditions for RhB adsorption onto Cu-BTC@Alg/Fe3O4 composites, highlighting their potential in wastewater treatment applications.