Genotypic and morphological identification of opportunistic microorganisms in triple-syringe tubing from dental units.

BACKGROUND: In Mexico and around the world, water in dental units, including triple syringes, comes from municipal chlorinated water mains. The microbial contamination of dental unit water systems constitutes a risk factor for opportunistic infections. OBJECTIVES: The present work aimed to identify the bacteria present in the triple-syringe water lines of dental units at a dental school of a public university in Mexico, with a hypothesis that opportunistic bacteria of importance to human health would be found. MATERIAL AND METHODS: A cross-sectional study was carried-out. A total of 100 samples of triple-syringe tubing from dental units operated by a dental school of a public university in Mexico were analyzed before and after their use in dental practice. Bacterial biofilm was cultured and isolated from the tubing, using standard microbiological methods, and then the species present were identified through 16S rRNA gene sequencing. The characterization of the biofilm was performed by means of scanning electron microscopy (SEM). RESULTS: Bacterial growth was observed in 20% of the non-disinfected and 10% of the disinfected samples, with 11 strains isolated. Six genera and 11 bacterial species were genetically identified. Coagulasenegative staphylococci (CoNS), considered opportunistic human pathogens, were among the most critical microorganisms. Scanning electron microscopy revealed a thick polymeric matrix with multiple bacterial aggregates. CONCLUSIONS: Opportunistic bacteria from human skin and mucous membranes were detected. Under normal conditions, these bacteria are incapable of causing disease, but are potentially harmful to immunosuppressed patients.

Environmental implications of dental restorative materials on the zebrafish Danio rerio: Are dental chair drainage systems an emerging environmental threat?

This study aimed to evaluate the environmental impact of dental materials: commercial composite Tetric EvoCeram®, glass ionomer Equia Forte® HT Fil, laboratory-prepared composite, alkasite Cention® Forte, amalgam Amalcap® Plus, and samples from dental chair drainage systems (DCDS). Methacrylate monomers were detected in the eluates of experimental and commercials composites, and alkasite. In DCDS samples solely mercury was found at concentrations of 0.08-1.86 µg/L. The experimental composite (48 h incubation) exhibited the highest toxicity on zebrafish Danio rerio (LC50=0.70 g/L), followed by amalgam (LC50=8.27 g/L) < Tetric EvoCeram® (LC50=10.94 g/L) < Equia Forte® HT Fil (LC50=24.84 g/L) < Cention® Forte (LC50=32.22 g/L). Exposure of zebrafish to DCDS samples resulted in decreased larval body length and increased occurrences of edema and blood accumulation. The results obtained highlight the need for additional monitoring and further research on the release of unreacted monomers and mercury from dental materials and their environmental impact.

[Expert consensus of regulations for the application of zero suckback technology in oral treatment].

Dental turbine is a commonly used instrument for oral clinical treatment. However, there is usually suckback during the using of the traditional dental turbine, which causes the pathogen residue in the pipeline of the dental comprehensive treatment table, leading to cross-infection. Zero suckback technology is a new oral treatment technology to avoid suckback during the usage of dental turbine, which can reduce the possibility of cross infection. However, the applications and methods of zero suckback technique in oral therapy remain to be clarified. This consensus mainly provides guidance for the clinical standard application of zero suckback technology from following aspects: field and definition, indications, applicable population, personnel requirements, operating process and evaluation of therapeutic effect.

Dental unit waterline infection control practice and knowledge gaps.

BACKGROUND: Dental unit waterline (DWL) infection control is critical to infection prevention. Identifying challenges and barriers to its implementation is a first step toward understanding how to improve engagement. METHODS: A survey was distributed to dentists, dental hygienists, and dental assistants via the Qualtrics XM platform (Qualtrics). Responses were analyzed to quantify engagement in practices contrary to Centers for Disease Control and Prevention guidance and identify avenues to improve engagement. RESULTS: Although oral health care providers recognized DWL infection control was important, there was a lack of clarity about appropriate routine engagement (eg, what lines should be tested), what should be noted in practice infection control records, and steps to be taken in response to a failed test result (ie, ≥ 500 colony-forming units/mL), such as taking a chair out of service. CONCLUSIONS: Survey results showed there were considerable gaps in knowledge and practice that could lead to patient harm. Oral health care provider training may not prepare personnel adequately to engage in, let alone supervise, DWL infection control. DWL infection control, like other aspects of infection control, requires action informed via an understanding of what needs to be done. Although good intentions are appreciated, better approaches to DWL infection control information dissemination and strategies to engage dental assistants, dental hygienists, and dentists in best practices are needed. PRACTICAL IMPLICATIONS: Evolving standards of care, including infection control, should be reflected in the provision of dental treatment. Improvements in communicating and ensuring engagement in best practices are needed when it comes to DWL infection control.

Study on the disinfection effect of chlorine dioxide disinfectant (ClO2) on dental unit waterlines and its in vitro safety evaluation.

BACKGROUND: Ensuring the safety of dental unit waterlines (DUWLs) has become a pivotal issue in dental care practices, focusing on the health implications for both patients and healthcare providers. The inherent structure and usage conditions of DUWLs contribute to the risk of biofilm formation and bacterial growth, highlighting the need for effective disinfection solutions.The quest for a disinfection method that is both safe for clinical use and effective against pathogens such as Staphylococcus aureus and Escherichia coli in DUWLs underscores the urgency of this research. MATERIALS: Chlorine dioxide disinfectants at concentrations of 5, 20, and 80 mg/L were used to treat biofilms of S. aureus and E. coli cultured in DUWLs. The disinfection effectiveness was assessed through bacterial counts and culturing. Simultaneously, human skin fibroblast cells were treated with the disinfectant to observe changes in cell morphology and cytotoxicity. Additionally, the study included corrosion tests on various metals (carbon steel, brass, stainless steel, aluminum, etc.). RESULTS: Experimental results showed that chlorine dioxide disinfectants at concentrations of 20 mg/L and 80 mg/L significantly reduced the bacterial count of S. aureus and E. coli, indicating effective disinfection. In terms of cytotoxicity, higher concentrations were more harmful to cellular safety, but even at 80 mg/L, the cytotoxicity of chlorine dioxide remained within controllable limits. Corrosion tests revealed that chlorine dioxide disinfectants had a certain corrosive effect on carbon steel and brass, and the degree of corrosion increased with the concentration of the disinfectant. CONCLUSION: After thorough research, we recommend using chlorine dioxide disinfectant at a concentration of 20 mg/L for significantly reducing bacterial biofilms in dental unit waterlines (DUWLs). This concentration also ensures satisfactory cell safety and metal corrosion resistance.

Microbial Contamination of Dental Unit Waterlines among Dental Clinics of India- An In vitro Study.

BACKGROUND: Dental Unit Water Line (DUWL) deliver water to different handpieces in a dental unit. The water in DUWL circulates in a closed system, where it is taken from a container. The quality of dental water is of considerable importance since patients and dental staff are regularly exposed to water and aerosols generated from dental equipment. Output water from DUWLs may be a potential source of infection for both dental health care personnel and patients. AIM: To assess the microbial contamination in the DUWL among dental clinics in Chennai. MATERIALS AND METHODS: An in vitro study was conducted on 60 water samples from 20 dental clinics in Chennai in December 2019. Water samples were collected from three different sources of the Dental unit according to ADA guidelines. The collected samples were assessed for the presence of Aspergillus, Acinetobacter, Pseudomonas aeruginosa, and Legionella by agar plate method. The data were analysed using SPSS software version 20. RESULTS: Legionella was the most prevalent microorganism with 70% prevalence in a three-way syringe and 50% in scaler and airotor, followed by Pseudomonas aeruginosa and Acinetobacter with 10% prevalence in scaler and airotor and Aspergillus with a prevalence of 10% in the three-way syringe. CONCLUSION: Most of the dental units were contaminated with Aspergillus, Legionella, Pseudomonas aeruginosa and Acinetobacter which pose a serious threat to the patients as well as the dentists.

Initial waterline contamination by Pseudomonas aeruginosa in newly installed dental chairs.

Water contamination in dental unit waterlines (DUWLs) is a potential source of healthcare-associated infection during dental care. The aim of this study was to evaluate the microbiological quality of DUWLs water from newly installed dental chairs in a French University Hospital. The microbiological quality of water from 24 new DUWLs initially disinfected by ICX Renew-prior to use of the dental units for patient treatment-was assessed for total culturable aerobic bacteria at 22°C and 36°C, Legionella sp., Pseudomonas aeruginosa, and total coliforms. Among the 24 samples analyzed, 21 were compliant with the water quality levels: 19 had no bacteria, and 2 contained only 4 and 1 CFU/mL for total culturable aerobic bacteria at 22°C and 36°C, respectively. Three samples were non-compliant due to contamination by P. aeruginosa (4, 2, and 2 CFU/100 mL). Controlling and preventing the microbiological contamination of DUWLs, especially by pathogenic bacteria, at the time of the installation of the new dental chairs are crucial to prevent healthcare-associated infection in dentistry. IMPORTANCE: Dental unit waterlines (DUWLs) of new dental chairs may be contaminated before their first clinical use, so an initial shock disinfection is crucial at the time of their installation. The microbiological analyses are crucial to control the water quality of DUWLs before their first clinical use because their disinfection does not guarantee the elimination of all bacteria.

Avaliação da precisão de localização foraminal de um motor endodôntico integrado em diferentes velocidades de rotação / Evaluation of foraminal location accuracy of an integrated endodontic motor employed with different rotational speeds

Objetivo: avaliar a precisão do controle do limite apical de instrumentação do motor endodôntico SENSORY, acionado em três velocidades de rotação (300, 600 e 900 RPM) e função de parada automática apical (Auto Apical Stop - AAS). Material e métodos: sessenta pré-molares inferiores humanos unirradiculados tiveram seus acessos realizados e diâmetro foraminal padronizado em 300 µm. Os dentes foram aleatoriamente divididos em três grupos (n=20) e tiveram seus canais preparados instrumento Logic 30/05, acionado na velocidade predefinida e função AAS ajustada para a marca 0,0. Os instrumentos foram medidos em paquímetro digital e o comprimento real do canal foi aferido pelo método visual direto sob magnificação. Resultados: os valores absolutos dos erros médios e de precisão (±0,5 mm), obtidos foram respectivamente: 0,21 mm e 95% (300 RPM), 0,26 mm e 95% (600 RPM), 0,20 mm e 95% (900 RPM). Não houve diferença significativa entre os grupos (P>0,05). Conclusão: nas condições deste estudo, o uso da função de parada automática forneceu um controle adequado e preciso do limite apical durante a modelagem endodôntica em todas as velocidades testadas.

Objective: to evaluate the accuracy of the control of the apical limit of instrumentation of the SENSORY endodontic motor, activated at three rotation speeds (300, 600 and 900 RPM) and apical automatic stop function (Auto Apical Stop - AAS). Material and methods: Sixty single-rooted human mandibular premolars had their access performed and the foraminal diameter was standardized at 300 µm. The teeth were randomly divided into three groups (n=20) and had their canals prepared with a Logic 30/05 instrument, activated at the predefined speed and the AAS function set to the 0.0 mark. The instruments were measured using a digital caliper and the actual canal length was measured using the direct visual method under magnification. Results: the absolute values of mean and precision errors (±0.5 mm) obtained were respectively: 0.21 mm and 95% (300 RPM), 0.26 mm and 95% (600 RPM), 0.20 mm and 95% (900 RPM). There was no significant difference between groups (P>0.05). Conclusion: Under the conditions of this study, the use of the automatic stop function provided adequate and accurate control of the apical limit during endodontic shaping at all speeds tested.

Accuracy of Working Length Determination - Electronic Apex Locator Versus Cone Beam Computed Tomography

ABSTRACT Objective: To compare the accuracy of working length determination between cone beam computed tomography (CBCT) and electronic apex locator by measuring the actual working length of teeth. Material and Methods: A total of 150 single-rooted tooth assessed by radiograph undergoing root canal therapy were selected. The process was repeated to obtain a buccolingual and mesiodistal section of all teeth. The measurement line was considered from the reference occlusal plane following the center of the canal to the terminus. All information regarding the accuracy of cone-beam computed tomography and apex locator was noted in a pre-designed proforma. Results: CBCT consistently demonstrated high accuracy across all tooth types in both jaws. The electronic apex locator exhibited varying precision, with greater accuracy observed in the mandible. Statistical analyses revealed significant differences in electronic apex locator accuracy among tooth types in the maxilla (p=0.042), emphasizing the importance of specific clinical considerations. Conclusion: Cone beam computed tomography emerges as a reliable diagnostic tool for accurate working length determination, especially in complex cases, while the electronic apex locator remains valuable with careful consideration of potential variations in accuracy. An individualized approach, considering tooth type, jaw location, and clinical context, is crucial for precise working length determination in endodontic practice.

Comparative evaluation of effect of sodium hypochlorite and chlorhexidine in dental unit waterline on aerosolized bacteria generated during dental treatment.

BACKGROUND: In dentistry, nosocomial infection poses a great challenge to clinicians. The microbial contamination of water in dental unit waterlines (DUWLs) is ubiquitous. Such infected DUWLs can transmit oral microbes in the form of aerosols. Previous studies have suggested treating DUWLs with various disinfectants to reduce cross-contamination. The literature lacks a comparative evaluation of the effect of the use of 0.2% chlorhexidine (CHX) and 0.1% sodium hypochlorite (NaOCl) in DUWLs on aerosolized bacteria generated during dental procedures. OBJECTIVE: To compare the effect of NaOCl and CHX in DUWLs on aerosolized bacteria generated during restorative and endodontic procedures. MATERIALS AND METHODS: A total of 132 patients were equally divided into three groups (n = 44 in each group) according to the content of DUWL as follows. Group I-0.1% NaOCl Group II-0.2% CHX Group III-distilled water (Positive control) One-way ANOVA was performed and the Kruskal-Wallis test was used for intergroup comparison. RESULTS: For the restorative procedure, inter-group comparison of mean colony-forming units (CFU) scores showed a statistically significant difference between the groups (p - .001) with the score of group 3 higher than group 2 followed by group 1. For the endodontics, an inter-group comparison of CFU scores showed a statistically significant difference between the groups (p - .003) with the mean score in group 1 being the lowest and group 3 being the highest. CONCLUSION: The addition of NaOCl or CHX in DUWLs shows an effective reduction in aerosolized bacteria compared to distilled water.

Dental unit waterline testing practices: an 11-Year retrospective study.

OBJECTIVES: This retrospective study examined the dental unit waterline (DUWL) testing practices of Saskatchewan dental clinics over a period of 11 years, with an emphasis on their responses after identification of high microbial levels. MATERIALS AND METHODS: Dental clinics (n = 137) aseptically collected samples of output water from their air/water syringes, handpieces, and ultrasonic scaler lines using Sigma-Aldrich® waterline test kits and delivered them to a quality assurance laboratory. Tests were incubated for seven days at room temperature, and those with heterotrophic plate counts > 500 CFU/mL were reported as failures. Statistical analyses were performed on a database containing 4,093 test results. RESULTS: Participating clinics submitted an average of 11 DUWL tests per year. Overall, 21% of tests failed, and a moderate positive association (rs=.52, p < 0.001) was found between clinics' DUWL testing frequency and failure rate. Only 7% of failed DUWL tests were followed up by collection of a subsequent test within two weeks, of which 47% still exceeded the 500 CFU/mL threshold. CONCLUSIONS: Our findings demonstrate an association between DUWL testing frequency and detection of unacceptable microbial levels, along with infrequent retesting and often-inadequate intervention after a failed test. This suggests the need for further efforts at the regulatory and educational levels to maintain adequate water quality during dental treatment. CLINICAL RELEVANCE: Procedural water can become contaminated in DUWLs and endanger patients. Regular DUWL monitoring and evidence-based interventions to treat contaminated systems are necessary to safeguard patient health.

La odontología verde / Green dentistry

El propósito del presente trabajo está orientado a generar una reflexión entre el gremio odontológico profesional y los estudiantes de las licenciaturas en Odontología respecto a la contaminación global que estamos generando y a la crítica situación del planeta, así como sus consecuencias ambientales y climatológicas, sobre lo importante que es educar bajo la perspectiva de una Odontología Verde y Sostenible a través de la ambientalización curricular en las escuelas y facultades de Odontología para generar un tipo de cultura y conciencia proambiental. De igual forma para señalar lo sencillo que es ambientalizar agradable y relajantemente nuestro entorno educativo y laboral, así como realizar algunas prácticas odontológicas ecológicas y ambientales en la práctica privada que cuestan poco o nada y que, por el contrario, el gran efecto positivo que éstas tendrán en el medio ambiente y la reducción de los niveles de contaminación actuales. Si realmente logramos generar una nueva cultura y conciencia que se preocupe por el medio ambiente en el campo de la Odontología, los resultados para todos se verán reflejados en un mejor ambiente social, educativo de trabajo y de salud (AU)

The purpose of this work is aimed at generating a reflection between the professional dental guild and the students of the Bachelor's Degrees in Dentistry regarding the global pollution that we are generating and the critical situation of the planet and its environmental and climatological consequences, on how important it is educate under the perspective of a Green and Sustainable Dentistry through the greening of the curriculum in the Schools and Faculties of Dentistry to generate a type of culture and pro-environmental awareness. Likewise, point out how simple it is to pleasantly and relaxingly green our educational and work environment, as well as perform some ecological and environment, as well perform some ecological and environment, dental practices in private practice that cost little or nothing and that, on the contrary, the great positive effect that these will have on the environment and the reduction of current pollution levels. If we truly manage to generate a new culture and awareness that cares about the environment in the field of Dentistry, the results for all will be reflected in a better social, educational, work and health environment (AU)

Desinfección y esterilización en odontología frente al COVID-19 / Disinfection and sterilization in dentistry against COVID-19 / Desinfecção e esterilização em odontologia contra a COVID-19

A partir de la declaración de la Organización Mundial de la Salud del comienzo de la pandemia COVID-19 causada por el virus SARS-CoV-2 en marzo de 2020, los profesionales de la salud se vieron expuestos a esta enfermedad altamente contagiosa y potencialmente mortal que generó múltiples desafíos a toda la comunidad científica. Provocando cambios de paradigmas en la atención de los pacientes y en el uso de las barreras de protección personal. A nivel mundial se crearon múltiples protocolos para la atención odontológica a medida que se iba desarrollando e investigando el comportamiento del virus. Esta revisión bibliográfica resume las indicaciones y recomendaciones basadas en las evidencias disponibles para disminuir las posibilidades de contaminación ante la exposición a este virus, incluyendo medidas a utilizar desde el ingreso del paciente, los métodos de protección personal, la descontaminación y esterilización del material, así como también la desinfección del área de trabajo. Aunque se ha hecho un gran esfuerzo por mejorar los procesos de bioseguridad a nivel científico tecnológico, hay evidencias de que el factor humano sigue siendo el eslabón más débil de esta cadena.

Since the declaration by the World Health Organization of the beginning of the COVID-19 pandemic caused by the SARS-CoV-2 virus in March 2020, health professionals were exposed to this highly contagious and potentially fatal disease that generated multiple challenges to the entire scientific community. It caused paradigm shifts in patient care and in the use of personal protective barriers. Multiple protocols for dental care were created worldwide as the behavior of the virus was developed and investigated. This bibliographic review summarizes the indications and recommendations based on the available evidence to reduce the possibilities of contamination when exposed to this virus, including measures to be used from patient admission, personal protection methods, decontamination and sterilization of material, as well as disinfection of the work area. Although a great effort has been made to improve biosafety processes at the scientific and technological level, there is evidence that the human factor continues to be the weakest link in this chain.

Desde a declaração pela Organização Mundial da Saúde do início da pandemia de COVID-19 causada pelo vírus SARS-CoV-2 em março de 2020, os profissionais de saúde foram expostos a essa doença altamente contagiosa e potencialmente fatal, que criou vários desafios para toda a comunidade científica. Ela causou mudanças de paradigma no atendimento ao paciente e no uso de barreiras de proteção individual. Em todo o mundo, vários protocolos para atendimento odontológico foram criados à medida que o comportamento do vírus foi desenvolvido e pesquisado. Esta revisão da literatura resume as indicações e recomendações baseadas em evidências para reduzir a probabilidade de contaminação por exposição a esse vírus, incluindo medidas a serem usadas desde a admissão do paciente, métodos de proteção individual, descontaminação e esterilização de equipamentos, bem como desinfecção da área de trabalho. Embora muitos esforços tenham sido feitos para melhorar os processos de biossegurança em nível científico e tecnológico, há evidências de que o fator humano continua sendo o elo mais fraco dessa cadeia.

Impact of cooling on shaping ability of thermally treated files in canal models with double curvature.

Background: This study compared the ability of thermally treated files in shaping simulated canals with double curvature. Fifty-six canals were enlarged to a final size of 25 with ProTaper Next (PTN) or ZenFlex (ZF). Materials: Half of the samples were shaped with cooled files (n = 14 each). The amount of removed resin was measured and canal deviation was determined at eight levels. Shaping time and maximum shaping torque values were also recorded. Data were statistically analyzed using analysis of variance and LSD, Kruskal-Wallis, and chi-square tests at a 0.05 significance level. Results: Compared to PTN and cooled PTN, ZF and cooled ZF required lesser time to shape the canals. The maximum torques were found comparable between the groups. All the groups generated negligible deviations at every canal level evaluated and maintained the canal geometry. Although not significant, the cooled PTN and ZF files exhibited lesser canal deviations than their counterparts. Conclusion: All groups demonstrated similar shaping ability whilst maintaining the original curvature of the canal in simulated canals with double curvature. However, ZF groups were able to shape the canals faster than PTN groups. There was a trend that cooled files made lesser canal deviations compared to their counterparts.

Corrección del artefacto producido en imágenes tomográficas en equipos odontológicos / Correction of the artifact produced in tomographic images in dental equipment

Objetivo: disminuir el efecto de artefacto que generan objetos de alta densidad mediante la utilización de filtros de distintos materiales y espesores, ubicados en lugares estratégicos del tomógrafo. Material y métodos: se utilizaron filtros de aluminio y de cobre ubicados en lugares estratégicos en el equipo tomográfico. Se realizaron cortes oblicuos en piezas dentarias con restauraciones metálicas y en implantes; se midió la extensión del artefacto en ancho y alto en cada adquisición tomográfica. Resultados: se hallaron diferencias significativas respecto a la disminución de la dispersión de acuerdo con cada filtro con respecto a la no utilización de estos elementos. Conclusión: la utilización de filtros logró disminuir el efecto de artefacto en estructuras de alta densidad, obteniendo una mejor calidad de imagen para el diagnóstico, permitiendo que el software pueda reconstruir una imagen real (AU)

Objective: to diminish the artifact effect generated by high density objects by using filters of different materials and thickness, located in strategic places of the tomograph. Material and methods: aluminum and copper filters located in strategic places in the tomographic equipment were used. Oblique cuts were made on dental pieces with metal restorations and implants; the extension of the artifact in width and height was measured in each tomographic acquisition. Results: significant differences were found regarding the decrease of the dispersion according to each filter with respect to the non-use of these elements. Conclusion: the use of filters achieves to diminish the artifact effect in structures of high density, obtaining a better image quality for the diagnosis, allowing the software to reconstruct a real image (AU)

Bacterial biofilm prevalence in dental unit waterlines: a systematic review and meta-analysis.

BACKGROUNDS: Numerous studies have shown that dental unit water lines (DUWLs) are often contaminated by a wide range of micro-organisms (bacteria, fungi, protozoa) and various prevalence have been reported for it in previous studies. Therefore, this review study aims to describe the prevalence of bacterial biofilm contamination of DUWLs. METHODS: This is a systematic review and meta-analysis in which the related keywords in different international databases, including Medline (via PubMed) and Scopus were searched. The retrieved studies were screened and the required data were extracted from the included studies. Three standard methods including American Dental Association (ADA), The Center for Disease Control and Prevention (CDC) and contaminated > 100 CFU/ml(C-100) standards were used to assess the bacterial biofilm contamination of DUWLs. All studies that calculated the prevalence of bacterial biofilm contamination of DUWLs, and English full-text studies were included in the meta-analysis. Studies that did not have relevant data or used unusual laboratory methods were excluded. Methodological risk of bias was assessed by a related checklist and finally, the data were pooled by fixed or random-effect models. RESULTS: Seven hundred and thirty-six studies were identified and screened and 26 related studies were included in the meta-analysis. The oldest included study was published in 1976 and the most recent study was published in 2020. According to the ADA, CDC and C-100 standards, the prevalence of bacterial contamination was estimated to be 85.0% (95% confidence interval (CI): 66.0-94.0%), 77.0% (95%CI: 66.0-85.0%) and 69.0% (95%CI: 67.0-71.0%), respectively. The prevalence of Legionella Pneumophila and Pseudomonas Aeruginosa in DUWLs was estimated to be 12.0% (95%CI: 10.0-14.0%) and 8.0% (95%CI: 2.0-24.0%), respectively. CONCLUSION: The results of this review study suggested a high prevalence of bacterial biofilm in DUWLs; therefore, the use of appropriate disinfecting protocol is recommended to reduce the prevalence of contamination and reduce the probable cross-infection.

Accuracy of an endodontic rotary motor with integrated apex locator to determine the root canal length / Precisão de um motor rotatório endodôntico com localizador apical integrado para determinação do comprimento radicular

Aim: The purpose of this study was to evaluate the efficacy to determine the root canal length, in vitro,of both the electronic apex locator (M2) and the autostop (AS - M3) functions of the Endus Duo Gnatus endodontic motor (Gnatus, São Paulo, SP, Brazil). Methods: Thirty extracted human single-rooted premolars had their root canal lengths (TLs) up to the apical foramen determined using the Endus Duo Gnatus in two ways: (1) In the stainless steel (SS) control group, the measurement was obtained using a stainless steel hand instrument with the electronic locator mode (M2 function) connected to a stainless-steel hand instrument (K-file #15). In the NiTi rotary instrument (NiTi RI) intervention group, the measurement was obtained during the instrumentation (M3 function) of the root canals with a nickel-titanium rotary instrument (Hyflex CM: Coltene Whaledent, Cuyahoga Falls, OH, USA), size 25/.06. The NiTi manually used instrument (NiTi MUI) Intervention group performed the measurement in locator mode using a Hyflex instrument, placed to true length manually. Statistical analysis was performed using ANOVA followed by the Tukey post-hoc test with a significance level of p < 0.05. Results: The true mean length and standard deviation (SD) of the standardized root canals were 18.40 ± 2.14mm, while the mean lengths and standard deviations (SD) were 18.29 ± 1.89mm, 18.22 ± 1.85mm, and 17.24 ± 2.09mm for the SS, NiTi RI, and NiTi MUI groups, respectively. However, data from the NiTi MUI Intervention group indicated shorter root canal lengths when compared to the SS control group and the NiTi RI Intervention group values, and were significantly shorter than the true canal length (p < 0.001). Conclusions:The use of the motor in NiTi RI Intervention group showed acceptable results. However, the NiTi MUI Intervention group resulted in unacceptable short measurements.

Objetivo: O objetivo deste estudo foi avaliar a eficácia na determinação do comprimento do canal radicular, in vitro, das funções localizador eletrônico foraminal (M2) e auto-parada durante a instrumentação (M3) do motor endodôntico Endus Duo Gnatus ( Gnatus, São Paulo, SP, Brasil). Métodos: Trinta pré-molares humanos uniradiculares extraídos tiveram seus comprimentos de canais radiculares (CRTs) até o forame apical determinados usando o Endus Duo Gnatus de duas maneiras: (1) No grupo controle de aço inoxidável (SS), a medida foi obtida usando um instrumento manual de aço inoxidável com modo de localização eletrônica foraminal (função M2) conectado a um instrumento manual de aço inoxidável (lima tipo K #15). No grupo intervenção instrumento rotatório NiTi (NiTi RI), a medida foi obtida durante a instrumentação (função M3) dos canais radiculares com instrumento rotatório de níquel-titânio (Hyflex CM: Coltene Whaledent, Cuyahoga Falls, OH, EUA), tamanho 25/.06. O grupo de intervenção NiTi instrumento usado manualmente (NiTi MUI) realizou a medição no modo localizador foraminal usando um instrumento Hyflex, colocado manualmente no comprimento real do dente. A análise estatística foi realizada por meio de ANOVA seguida do teste post-hoc de Tukey com nível de significância de p < 0,05. Resultados: Os comprimentos reais médios dos dentes e desvios-padrão (DP) dos canais radiculares padronizados foram 18,40 ± 2,14 mm, enquanto os comprimentos médios e desvios- padrão (DP) foram 18,29 ± 1,89 mm, 18,22 ± 1,85 mm e 17,24 ± 2,09 mm para os grupos SS, NiTi RI e NiTi MUI, respectivamente. No entanto, os dados do grupo de intervenção NiTi MUI indicaram comprimentos de canais radiculares mais curtos quando comparados aos valores do grupo controle SS e do grupo de intervenção NiTi RI, e foram significativamente mais curtos que o comprimento real do canal (p < 0,001). Conclusões: A utilização do motor no grupo Intervenção NiTi RI apresentou resultados aceitáveis. No entanto, o grupo de intervenção NiTi MUI resultou em medições curtas inaceitáveis.

Comparative evaluation of debris and irrigation extruded apically using different design of needles and penetration depth - An In Vitro study.

Aim: : The aim of this study was to measure the amount of material extruded in the periapical area using three irrigation needles (Max-I-Probe, NaviTip Fx and IrriFlex flexible needle). Materials and Methods: : Mandibular premolars were selected for this study and glass vials were used to gather the extruded debris and they were preweighed. The samples were divided into two groups: Group A (1 mm penetration of needle from working length), which was subdivided into three subgroups: Subgroup A1: Irrigation was made by Max-I-Probe. Subgroup A2: Irrigation was made by NaviTip Fx. Subgroup A3: Irrigation was made by IrriFlex flexible needle. Group B (3 mm penetration of needle), which was subdivided into three subgroups: Subgroup B1: Irrigation was made by Max-I-Probe. Subgroup B2: Irrigation was made by NaviTip Fx. Subgroup B3: Irrigation was made by IrriFlex flexible needle. XP-endo Shaper was used for chemomechanical preparation. After removal from vials, the teeth were incubated and then removed from the incubator and weighed again three times. The average of the readings was taken. Analysis of variance (ANOVA) and least significance difference tests were applied to analyse data. Results: : All of the needles caused debris extrusion. There was a significant difference between groups (P ≤ 0.001) according to the depth of penetration. The lowest value for debris was observed in subgroup B3 while subgroup A2 had shown the highest mean. Conclusion: Results revealed that the design and depth of needles significantly affected the debris extrusion. Using more flexible needles and shorter penetration depth for irrigation so that we don't need to push the needles so far apically.