Cortical bone plate properties assessment using inversion of axially transmitted low frequency ultrasonic guided waves.

Over the past few decades, early osteoporosis detection using ultrasonic bone quality evaluation has gained prominence. Specifically, various studies focused on axial transmission using ultrasonic guided waves and have highlighted this technique's sensitivity to intrinsic properties of long cortical bones. This work aims to demonstrate the potential of low-frequency ultrasonic guided waves to infer the properties of the bone inside which they are propagating. A proprietary ultrasonic transducer, tailored to transmit ultrasonic guided waves under 500 kHz, was used for the data collection. The gathered data underwent two-dimensional fast Fourier transform processing to extract experimental dispersion curves. The proposed inversion scheme compares experimental dispersion curves with simulated dispersion curves calculated through the semi-analytical iso-geometric analysis (SAIGA) method. The numerical model integrates a bone phantom plate coupled with a soft tissue layer on its top surface, mimicking the experimental bone phantom plates. Subsequently, the mechanical properties of the bone phantom plates were estimated by reducing the misfit between the experimental and simulated dispersion curves. This inversion leaned heavily on the dispersive trajectories and amplitudes of ultrasonic guided wave modes. Results indicate a marginal discrepancy under 5% between the mechanical properties ascertained using the SAIGA-based inversion and those measured using bulk wave pulse-echo measurements.

Medial cortical bone thickness of the tibial diaphysis in osteoarthritis is related to lower extremity alignment and tibial morphology.

BACKGROUND: The purpose of this study was to clarify (1) the differences in cortical bone thickness (CBT) of the tibial diaphysis between healthy and osteoarthritic knees and (2) the influences of the femorotibial angle (FTA) and inclination of the medial compartment of the proximal tibia (MCT) on tibial CBT. METHODS: The study assessed 60 subjects with varus knee osteoarthritis (OA) (22 males and 38 females; mean age, 74 ± 7 years) and 53 healthy elderly subjects (28 males and 25 females; mean age, 70 ± 6 years). Three-dimensional estimated CBT of the tibial diaphysis was automatically calculated for 2752-11,296 points using high-resolution measurements from CT. The standardized CBT was assessed in 24 regions by combining six heights and four areas. Additionally, the association between the CBT, each FTA, and MCT inclination was investigated. RESULTS: The OA group showed a thicker CBT in the medial areas than in the lateral areas of the proximal tibia, while the healthy group had a thicker lateral CBT. The medial-to-lateral ratio of the proximal tibia was significantly higher in the OA group than in the healthy group. The proximal-medial CBT correlated with FTA and MCT inclinations in the OA group. CONCLUSIONS: This study demonstrated that varus osteoarthritic knees showed a different trend of proximal-medial CBT with associations in FTA and MCT inclination from healthy knees, possibly due to medial load concentration.

The comparison of visibility of the maxillary sinus septa between cone-beam computed tomography scans and panoramic radiograph images as dependent on the cortical bone thickness: a retrospective comparative study.

PURPOSE: To analyze the visibility of the maxillary sinus septa (MSS) in panoramic radiography (PR) versus cone beam computed tomography (CBCT) and to investigate whether the buccal cortical bone thickness (BT) or the septa dimensions influence their visibility. METHODS: Corresponding PR and CBCT images of 355 patients were selected and examined for MSS visibility. The septa dimensions (width, height, depth) and the BT were measured. Results were analysed statistically. RESULTS: Comparing the corresponding regions on CBCT and PR, 170 MSS were identified; however, only 106 of these were also visible using PR. The MSS visibility was significantly higher on CBCT versus PR images (P1: p = 0.039, P2: p = 0.015, M1: p = 0.041, M2: p = 0.017, M3: p = 0.000), except region C (p = 0.625). Regarding the measurements of MSS dimensions, only the height in region M1 (p = 0.013) and the width in region P2 (p = 0.034) were significantly more visible on CBCT. The BT in the area of the MSS was found to have a marginal influence on its visibility on the PR images only in regions M3 and M1 (M3: p = 0.043, M1: p = 0.047). In terms of MSS visibility based on the dimensions, significance was found for all three influencing variables only in region P2 (width; p = 0.041, height; p = 0.001, depth; p = 0.007). There were only isolated cases of further significance: M3 for width (p = 0.043), M2 for height (p = 0.024), and P1 for depth (p = 0.034), no further significance was noted. CONCLUSION: MSS visibility appears significantly higher on CBCT versus PR images. It is concluded that the septa dimensions and BT can influence MSS visibility on PR images just in certain regions.

Cortical hypertrophy in intramuscular hemangioma mimicking bone tumor.

Although hemangiomas are the most common soft tissue tumors, intramuscular hemangiomas account for only 0.8% of all vascular tumors. These lesions are rarely located adjacent to the bone and cause changes in the adjacent bone. They are often mistakenly diagnosed as bone tumors. In this study, a case of a 19-year-old male patient with intramuscular hemangioma causing cortical thickening was reported.

Ex vivo analysis of cortical microarchitecture of the distal clavicle: implications for surgical management of fractures.

BACKGROUND: Cortical thickness and porosity are two main determinants of cortical bone strength. Thus, mapping variations in these parameters across the full width of the distal end of the clavicle may be helpful for better understanding the basis of distal clavicle fractures and for selecting optimal surgical treatment. METHODS: Distal ends of 11 clavicles (6 men, 5 women; age: 81.9 ± 15.1 years) were scanned by micro-computed tomography at 10-µm resolution. We first analyzed cortical thickness and porosity of each 500-µm-wide area across the superior surface of distal clavicle at the level of conoid tubercle in an antero-posterior direction. This level was chosen for detailed evaluation because previous studies have demonstrated its superior microarchitecture relative to the rest of the distal clavicle. Subsequently, we divided the full width of distal clavicle to three subregions (anterior, middle, and posterior) and analyzed cortical porosity, pore diameter, pore separation, and cortical thickness. RESULTS: We found the largest number of low-thickness and high-porosity areas in the anterior subregion. Cortical porosity, pore diameter, pore separation, and cortical thickness varied significantly among the three subregions (p < 0.001 p = 0.016, p = 0.001, p < 0.001, respectively). Cortex of the anterior subregion was more porous than that of the middle subregion (p < 0.001) and more porous and thinner than that of the posterior subregion (p < 0.001, p = 0.030, respectively). Interaction of site and sex revealed higher porosity of the anterior subregion in women (p < 0.001). The anterior subregion had larger pores than the middle subregion (p = 0.019), whereas the middle subregion had greater pore separation compared with the anterior (p = 0.002) and posterior subregions (p = 0.006). In general, compared with men, women had thinner (p < 0.001) and more porous cortex (p = 0.03) with larger cortical pores (p < 0.001). CONCLUSIONS: Due to high cortical porosity and low thickness, the anterior conoid subregion exhibits poor bone microarchitecture, particularly in women, which may be considered in clinical practice. LEVELS OF EVIDENCE: Level IV.

Investigation of Skull Cortical Thickness Changes in Healthy Population and Patients With Schizophrenia on Computed Tomography Images.

Cortical bone thickness is essential for the mechanical function of bone. Some factors including aging, sex, body size, hormone levels, behavior, and genetics lead to changes in cranial cortical robusticity. Moreover, the skull is one of the hardest and most durable structures in the human body. Schizophrenia is defined as a psychiatric disease characterized by delusions and hallucinations, and these patients have reduced brain volume; however, there is no study including cortical bone structure. For this reason, the aim of this study was to determine whether there is a difference in the skull cortical thickness of patients with schizophrenia and, compare it with healthy subjects. The cranial length, cranial width, anterior cortical thickness, right and left anterior cortical thickness, right and left lateral cortical thickness, right and left posterior lateral thickness, and posterior cortical thickness were measured with axial computed tomography images of 30 patients with schizophrenia and 132 healthy individuals aged between 18 and 69years. A statistically significant difference was found between the two groups in the measurements of right and left posterior lateral thickness, and posterior cortical thickness ( P = 0.006, P = 0.001, and P = 0.047, respectively). The sexes were compared, and it was found that the cranial width, anterior thickness, left anterior thickness, and right and left posterior thickness measurements of patients with schizophrenia showed a statistically significant difference compared with the control group ( P < 0.001, P = 0.003, P = 0.001, P < 0.001 and P < 0.001, respectively). The authors observed that skull cortical thickness may be different in schizophrenia. The results obtained from this study may be beneficial for evaluating these structures for clinical and pathological processes. Furthermore, knowledge about the skull cortical thickness in planning surgical procedures will increase the reliability and effectiveness of the surgical method, and this will minimize the risk of complications.

Design and radiological confirmation of 3-column cortical bone trajectory in the lumbar spine.

OBJECTIVE: The aim of this study was to design a novel lumbar cortical bone trajectory (CBT) penetrating the anterior, middle, and posterior vertebral area using imaging; measure the relevant parameters to find theoretical parameters and screw placement possibilities; and investigate the optimal implantation trajectory of the CBT in patients with osteoporosis. METHODS: Three types of CBTs with appropriate lengths were selected to simulate screw placement using Mimics software. These CBTs were classified as the leading tip of the trajectory pointing to the posterior quarter area (original CBT [CBT-O]) and middle (novel CBT A [CBT-A]) and anterior quarter (novel CBT B [CBT-B]) of the superior endplate. The authors then measured the maximum screw diameter (MSD) and length (MSL), cephalad (CA) and lateral (LA) angles, and bone mineral density (Hounsfield unit [HU] values) of the planned novel 3-column CBT screw placements. The differences in the parameters of the novel CBTs, the percentages of successfully planned CBT screws, and the factors that influenced the successful planning of 3-column CBT screws were analyzed. RESULTS: Three-column CBT screws were successfully designed in all segments of the lumbar spine. The success rate of the 3-column CBT planned screws was 72.25% (83.25% for CBT-A and 61.25% for CBT-B). From the CBT-O type, to the CBT-A type, to the CBT-B type, the LA, CA, and MSD of the novel CBT screws decreased with increasing trajectory length. The HU values of the three types of trajectories were all significantly higher than that of the traditional pedicle screw trajectory (p < 0.001). The main factor affecting successful planning of the 3-column CBT screw was pedicle width. CONCLUSIONS: Moderating adjustment of the original screw parameters by reducing LAs and CAs to penetrate the anterior, middle, and posterior columns of the vertebral body using the 3-column CBT screw is feasible, especially in the lower lumbar spine.

Osteomodulin deficiency in mice causes a specific reduction of transversal cortical bone size.

Skeletal growth, modeling, and remodeling are regulated by various molecules, one of them being the recently identified osteoanabolic factor WNT1. We have previously reported that WNT1 transcriptionally activates the expression of Omd, encoding Osteomodulin (OMD), in a murine mesenchymal cell line, which potentially explained the skeletal fragility of mice with mutational WNT1 inactivation, since OMD has been shown to regulate type I collagen fibril formation in vitro. In this study we confirmed the strong induction of Omd expression in a genome-wide expression analysis of transfected cells, and we obtained further evidence for Omd being a direct target gene of WNT1. To assess the in vivo relevance of this regulation, we crossed Omd-deficient mice with a mouse line harboring an inducible, osteoblast-specific Wnt1 transgene. After induction of Wnt1 expression for 1 or 3 weeks, the osteoanabolic potency of WNT1 was not impaired despite the Omd deficiency. Since current knowledge regarding the in vivo physiological function of OMD is limited, we next focused on skeletal phenotyping of wild-type and Omd-deficient littermates, in the absence of a Wnt1 transgene. Here we did not observe an impact of Omd deficiency on trabecular bone parameters by histomorphometry and µCT either. Importantly, however, male and female Omd-deficient mice at the ages of 12 and 24 weeks displayed a slender bone phenotype with significantly smaller long bones in the transversal dimension, while the longitudinal bone growth remained unaffected. Although mechanical testing revealed no significant changes explained by impaired bone material properties, atomic force microscopy of the femoral bone surface of Omd-deficient mice revealed moderate changes at the nanostructural level, indicating altered regulation of collagen fibril formation and aggregation. Taken together, our data demonstrate that, although OMD is dispensable for the osteoanabolic effect of WNT1, its deficiency in mice specifically modulates transversal cortical bone morphology.

We explored the physiological relevance of the protein Osteomodulin (OMD) that we previously found to be induced by the osteoanabolic molecule WNT1. While other studies have shown that OMD is involved in the regulation of collagen fibril formation in vitro, its function in vivo has not been investigated. We confirmed that OMD is directly regulated by WNT1 but surprisingly, when we bred mice lacking OMD with mice engineered to highly express WNT1, we found that the osteoanabolic effect of WNT1 was unaffected by the absence of OMD. Interestingly, mice lacking OMD did show differences in the shape of their bones, particularly in their width, despite no significant changes in bone density or length. Investigation of the bone matrix of mice lacking OMD at the nanostructural level indicated moderate differences in the organization of collagen fibrils. This study provided further insights into the effect of WNT1 on bone metabolism and highlighted a specific function of OMD in skeletal morphology.

Micro-CT, Mechanical, and Histological Examination of the Effect of Local Adjuvants on Porcine Cortical Bone Following Intralesional Curettage of Bone Tumors.

BACKGROUND AND OBJECTIVES: Curettage is the removal of a tumor from the bone while preserving the surrounding healthy cortical bone, and is associated with higher rates of local recurrence. To lower these rates, curettage should be combined with local adjuvants, although their use is associated with damage to nearby healthy bone. OBJECTIVE: The purpose of this analysis is to determine the effect of local adjuvants on cortical porcine bone by using micro-computed tomography (micro-CT) along with histological and mechanical examination. METHODS: Local adjuvants were applied to porcine specimens under defined conditions. To assess changes in bone mineral density (BMD), a micro-CT scan was used. The pixel gray values of the volume of interest (VOI) were evaluated per specimen and converted to BMD values. The Vickers hardness test was employed to assess bone hardness (HV). The depth of necrosis was measured histologically using hematoxylin and eosin-stained tissue sections. RESULTS: A noticeable change in BMD was observed on the argon beam coagulation (ABC) sample. Comparable hardness values were measured on samples following electrocautery and ABC, and lowering of bone hardness was obtained in the case of liquid nitrogen. Extensive induced depth of necrosis was registered in the specimen treated with liquid nitrogen. CONCLUSION: This study determined the effect of local adjuvants on cortical bone by using micro-CT along with histological and mechanical examination. Phenolization and liquid nitrogen application caused a decrease in bone hardness. The bone density was affected in the range of single-digit percentage values. Liquid nitrogen induced extensive depth of necrosis with a wide variance of values.

The respective and dependent effects of scattering and bone matrix absorption on ultrasound attenuation in cortical bone.

Cortical bone is characterized by a dense solid matrix permeated by fluid-filled pores. Ultrasound scattering has potential for the non-invasive evaluation of changes in bone porosity. However, there is an incomplete understanding of the impact of ultrasonic absorption in the solid matrix on ultrasound scattering. In this study, maps were derived from scanning acoustic microscopy images of human femur cross-sections. Finite-difference time domain ultrasound scatter simulations were conducted on these maps. Pore density, diameter distribution of the pores, and nominal absorption values in the solid and fluid matrices were controlled. Ultrasound pulses with a central frequency of 8.2 MHz were propagated, both in through-transmission and backscattering configurations. From these data, the scattering, bone matrix absorption, and attenuation extinction lengths were calculated. The results demonstrated that as absorption in the solid matrix was varied, the scattering, absorption, and attenuation extinction lengths were significantly impacted. It was shown that for lower values of absorption in the solid matrix (less than 2 dB mm-1), attenuation due to scattering dominates, whereas at higher values of absorption (more than 2 dB mm-1), attenuation due to absorption dominates. This will impact how ultrasound attenuation and scattering parameters can be used to extract quantitative information on bone microstructure.

Six months of voluntary alcohol consumption in male cynomolgus macaques reduces intracortical bone porosity without altering mineralization or mechanical properties.

Chronic heavy alcohol consumption is a risk factor for low trauma bone fracture. Using a non-human primate model of voluntary alcohol consumption, we investigated the effects of 6 months of ethanol intake on cortical bone in cynomolgus macaques (Macaca fascicularis). Young adult (6.4 ± 0.1 years old, mean ± SE) male cynomolgus macaques (n = 17) were subjected to a 4-month graded ethanol induction period, followed by voluntary self-administration of water or ethanol (4 % w/v) for 22 h/d, 7 d/wk. for 6 months. Control animals (n = 6) consumed an isocaloric maltose-dextrin solution. Tibial response was evaluated using densitometry, microcomputed tomography, histomorphometry, biomechanical testing, and Raman spectroscopy. Global bone response was evaluated using biochemical markers of bone turnover. Monkeys in the ethanol group consumed an average of 2.3 ± 0.2 g/kg/d ethanol resulting in a blood ethanol concentration of 90 ± 12 mg/dl in longitudinal samples taken 7 h after the daily session began. Ethanol consumption had no effect on tibia length, mass, density, mechanical properties, or mineralization (p > 0.642). However, compared to controls, ethanol intake resulted in a dose-dependent reduction in intracortical bone porosity (Spearman rank correlation = -0.770; p < 0.0001) and compared to baseline, a strong tendency (p = 0.058) for lower plasma CTX, a biochemical marker of global bone resorption. These findings are important because suppressed cortical bone remodeling can result in a decrease in bone quality. In conclusion, intracortical bone porosity was reduced to subnormal values 6 months following initiation of voluntary ethanol consumption but other measures of tibia architecture, mineralization, or mechanics were not altered.

Cortical Block Grafting Successfully Augments Alveolar Cleft Sites for Dental Implant Placement.

BACKGROUND: Supplemental bone grafting is regularly required before dental implant placement in patients with cleft lip and palate (CLP). PURPOSE: The study purpose was to measure and compare implant osseointegration and changes in graft dimensions following lateral incisor onlay cortical bone grafting in CLP and non-CLP patients. STUDY DESIGN, SETTING, SAMPLE: Retrospective cohort study composed of patients who presented to Boston Children's Hospital and underwent autogenous onlay cortical block bone grafting at lateral incisor sites from 2015 through 2023. Patients were excluded if the cone beam computed tomography (CBCT) quality was insufficient for accurate measurements. PREDICTOR VARIABLE: The predictor variable was CLP status coded as CLP or non-CLP. MAIN OUTCOME VARIABLE: The primary outcome variable was successful implant osseointegration confirmed by a torque of 35 N/cm or more after 3 months of implant healing. Secondary outcomes were change in bone width between preoperative and postoperative CBCT scans at lateral incisor sites and the need for additional bone augmentation prior to or during implant placement. COVARIATES: Covariates were age, sex, cleft location, and time from bone graft to postoperative CBCT and implant placement. ANALYSES: Data analyses were performed using t-tests, Fisher's exact tests, Mann-Whitney U tests, and Pearson's correlation. P < .05 was considered statistically significant. RESULTS: A total of 22 subjects (16 with CLP) were evaluated. The mean age at the time of graft was 19.3 ± 2.4 years with 52.6% males. Implants were osseointegrated at 20 of 22 lateral incisor sites (1 CLP failure, 1 non-CLP failure). There was significant change in bone width after grafting for patients with CLP (P < .001). Patients with CLP experienced a 3.32 (± 1.80) mm and 2.99 (± 1.61) mm increase in bone width at 2 different levels. Patients with CLP achieved greater boney changes near the alveolar crest than noncleft patients (P = .008) but the change was not significantly different more apically (P = .86). One subject with CLP required additional grafting during implant placement. CONCLUSION AND RELEVANCE: Cortical block onlay bone grafting is a predictable technique to augment lateral incisor sites in patients with CLP for placement of a dental implant.

Ultrashort echo time MRI detects significantly lower collagen but higher pore water in the tibial cortex of female patients with osteopenia and osteoporosis.

Ultrashort echo time (UTE) MRI can quantify the major proton pool densities in cortical bone, including total (TWPD), bound (BWPD), and pore water (PWPD) proton densities, as well as the macromolecular proton density (MMPD), associated with the collagen content, which is calculated using macromolecular fraction (MMF) from UTE magnetization transfer (UTE-MT) modeling. This study aimed to investigate the differences in water and collagen contents in tibial cortical bone, between female osteopenia (OPe) patients, osteoporosis (OPo) patients, and young participants (Young). Being postmenopausal and above 55 yr old were the inclusion criteria for OPe and OPo groups. The tibial shaft of 14 OPe (72.5 ± 6.8 yr old), 31 OPo (72.0 ± 6.4 yr old), and 31 young subjects (28.0 ± 6.1 yr old) were scanned using a knee coil on a clinical 3T scanner. Basic UTE, inversion recovery UTE, and UTE-MT sequences were performed. Investigated biomarkers were compared between groups using Kruskal-Wallis test. Spearman's correlation coefficients were calculated between the TH DXA T-score and UTE-MRI results. MMF, BWPD, and MMPD were significantly lower in OPo patients than in the young group, whereas T1, TWPD, and PWPD were significantly higher in OPo patients. The largest OPo/Young average percentage differences were found in MMF (41.9%), PWPD (103.5%), and MMPD (64.0%). PWPD was significantly higher (50.7%), while BWPD was significantly lower (16.4%) in OPe than the Young group on average. MMF was found to be significantly lower (27%) in OPo patients compared with OPe group. T1, MMF, TWPD, PWPD, and MMPD values significantly correlated with the TH DXA T-scores (provided by the patients and only available for OPe and OPo patients). DXA T-score showed the highest correlations with PWPD (R = 0.55) and MMF (R = 0.56) values. TWPD, PWPD, and MMF estimated using the UTE-MRI sequences were recommended to evaluate individuals with OPe and OPo.

Ultrashort echo time (UTE) is an MRI technique that can quantify the water and collagen content of cortical bone. Water in the bone can be found residing in pores (pore water) or bound to the bone matrix (bound water). We investigated the differences in water and collagen contents of tibial cortical bone between female osteopenia patients, osteoporosis patients, and young participants. Bound water and collagen contents were significantly lower in osteoporosis patients than in the young group, whereas total water and pore water contents were significantly higher in osteoporosis patients. Pore water was significantly higher, while bound water was significantly lower in osteopenia than in the Young group. Collagen content was found to be significantly lower in osteoporosis patients compared with the osteopenia group. The estimated water and collagen contents were significantly correlated with the TH bone densitometry measures in the patients.

TBS correlates with bone density and microstructure at trabecular and cortical bone evaluated by HR-pQCT.

INTRODUCTION: Trabecular bone score (TBS) estimates bone microstructure, which is directly measured by high-resolution peripheral quantitative computed tomography (HRpQCT). We evaluated the correlation between these methods and TBS influence on fracture risk assessed by FRAX. MATERIALS AND METHODS: We evaluated 129 individuals (82 women, 43 postmenopausal) 20 to 82.3 years without prevalent clinical or non-clinical morphometric vertebral fractures, using DXA (spine and hip), HR-pQCT at distal radius (R) and tibia (T) and TBS which classifies bone microarchitecture as normal (TBS ≥ 1.350), partially degraded (1.200 < TBS < 1.350), or degraded (TBS ≤ 1.200). RESULTS: Spine and hip BMD and HR-pQCT parameters at cortical bone: area (T), density (R,T) thickness (T) and trabecular bone: density (R,T), number (T) and thickness (R) were significantly better in the 78 individuals with normal TBS (group 1) versus the 51 classified as partially degraded (n = 42) or degraded microarchitecture (n = 9) altogether (group 2). TBS values correlated with age (r = - 0.55), positively with spine and hip BMD and all cortical and trabecular bone density and microstructure parameters evaluated, p < 0.05 all tests. Binary logistic regression defined age (p = 0.008) and cortical thickness (p = 0.018) as main influences on TBS, while ANCOVA demonstrated that HR-pQCT data corrected for age were not different between TBS groups 1 and 2. TBS adjustment increased FRAX risk for major osteoporotic fractures and hip fractures. CONCLUSION: We describe significant association between TBS and both trabecular and cortical bone parameters measured by HR-pQCT, consistent with TBS influence on fracture risk estimation by FRAX, including hip fractures, where cortical bone predominates.

Direct-Acting Oral Anticoagulant/Vitamin K Antagonists: Do They Affect the Trabecular and Cortical Structure of the Mandible?

BACKGROUND: This study aimed to evaluate the mandibular bone structure of patients using oral anticoagulants (OACs) vitamin K antagonist drugs (warfarin) and other OACs including direct oral anticoagulants [(DOACs) apixaban, rivaroxaban, dabigatran, edoxaban]. Analyses were based upon the fractal dimension (FD), the panoramic mandibular index (PMI) and the Klemetti index (KI), which is also known as the mandibular cortical index (MCI). METHODOLOGY: Ninety participants were divided into three groups: group 1: 30 systemically healthy individuals who had not used any anticoagulants before, group 2: 30 individuals using warfarin, and group 3: 30 individuals using DOACs. FD was used to analyze trabecular bone architecture in the condyle, angle, and two sites in the alveolar bone. PMI was used to evaluate the quantity of cortical bone and KI was used to evaluate the cortical bone quality. RESULTS: There was no difference between the groups regarding FD analysis and KI; however, a difference was found between groups 1, 2, and 3 in the PMI (P≤ 0.001). The PMI in group 1 was higher than in groups 2 and 3. CONCLUSION: Mandibular radiomorphometric indices can be used on panoramic radiographs to evaluate the quantity of mandibular cortical bone in patients using oral anticoagulants.

A numerical study of dehydration induced fracture toughness degradation in human cortical bone.

A 2D plane strain extended finite element method (XFEM) model was developed to simulate three-point bending fracture toughness tests for human bone conducted in hydrated and dehydrated conditions. Bone microstructures and crack paths observed by micro-CT imaging were simulated using an XFEM damage model. Critical damage strains for the osteons, matrix, and cement lines were deduced for both hydrated and dehydrated conditions and it was found that dehydration decreases the critical damage strains by about 50%. Subsequent parametric studies using the various microstructural models were performed to understand the impact of individual critical damage strain variations on the fracture behavior. The study revealed the significant impact of the cement line critical damage strains on the crack paths and fracture toughness during the early stages of crack growth. Furthermore, a significant sensitivity of crack growth resistance and crack paths on critical strain values of the cement lines was found to exist for the hydrated environments where a small change in critical strain values of the cement lines can alter the crack path to give a significant reduction in fracture resistance. In contrast, in the dehydrated state where toughness is low, the sensitivity to changes in critical strain values of the cement lines is low. Overall, our XFEM model was able to provide new insights into how dehydration affects the micromechanisms of fracture in bone and this approach could be further extended to study the effects of aging, disease, and medical therapies on bone fracture.

A comprehensive set of ultrashort echo time magnetic resonance imaging biomarkers to assess cortical bone health: A feasibility study at clinical field strength.

INTRODUCTION: Conventional bone imaging methods primarily use X-ray techniques to assess bone mineral density (BMD), focusing exclusively on the mineral phase. This approach lacks information about the organic phase and bone water content, resulting in an incomplete evaluation of bone health. Recent research highlights the potential of ultrashort echo time magnetic resonance imaging (UTE MRI) to measure cortical porosity and estimate BMD based on signal intensity. UTE MRI also provides insights into bone water distribution and matrix organization, enabling a comprehensive bone assessment with a single imaging technique. Our study aimed to establish quantifiable UTE MRI-based biomarkers at clinical field strength to estimate BMD and microarchitecture while quantifying bound water content and matrix organization. METHODS: Femoral bones from 11 cadaveric specimens (n = 4 males 67-92 yrs of age, n = 7 females 70-95 yrs of age) underwent dual-echo UTE MRI (3.0 T, 0.45 mm resolution) with different echo times and high resolution peripheral quantitative computed tomography (HR-pQCT) imaging (60.7 µm voxel size). Following registration, a 4.5 mm HR-pQCT region of interest was divided into four quadrants and used across the multi-modal images. Statistical analysis involved Pearson correlation between UTE MRI porosity index and a signal-intensity technique used to estimate BMD with corresponding HR-pQCT measures. UTE MRI was used to calculate T1 relaxation time and a novel bound water index (BWI), compared across subregions using repeated measures ANOVA. RESULTS: The UTE MRI-derived porosity index and signal-intensity-based estimated BMD correlated with the HR-pQCT variables (porosity: r = 0.73, p = 0.006; BMD: r = 0.79, p = 0.002). However, these correlations varied in strength when we examined each of the four quadrants (subregions, r = 0.11-0.71). T1 relaxometry and the BWI exhibited variations across the four subregions, though these differences were not statistically significant. Notably, we observed a strong negative correlation between T1 relaxation time and the BWI (r = -0.87, p = 0.0006). CONCLUSION: UTE MRI shows promise for being an innocuous method for estimating cortical porosity and BMD parameters while also giving insight into bone hydration and matrix organization. This method offers the potential to equip clinicians with a more comprehensive array of imaging biomarkers to assess bone health without the need for invasive or ionizing procedures.

Ultrasound attenuation of cortical bone correlates with biomechanical, microstructural, and compositional properties.

BACKGROUND: We investigated the relationship of two commonly used quantitative ultrasound (QUS) parameters, speed of sound (SoS) and attenuation coefficient (α), with water and macromolecular contents of bovine cortical bone strips as measured with ultrashort echo time (UTE) magnetic resonance imaging (MRI). METHODS: SoS and α were measured in 36 bovine cortical bone strips utilizing a single-element transducer with nominal 5 MHz center frequency based on the time of flight principles after accommodating for reflection losses. Specimens were then scanned using UTE MRI to measure total, bound, and pore water proton density (TWPD, BWPD, and PWPD) as well as macromolecular proton fraction and macromolecular transverse relaxation time (T2-MM). Specimens were also scanned using microcomputed tomography (µCT) at 9-µm isometric voxel size to measure bone mineral density (BMD), porosity, and pore size. The elastic modulus (E) of each specimen was measured using a 4-point bending test. RESULTS: α demonstrated significant positive Spearman correlations with E (R = 0.69) and BMD (R = 0.44) while showing significant negative correlations with porosity (R = -0.41), T2-MM (R = -0.47), TWPD (R = -0.68), BWPD (R = -0.67), and PWPD (R = -0.45). CONCLUSIONS: The negative correlation between α and T2-MM is likely indicating the relationship between QUS and collagen matrix organization. The higher correlations of α with BWPD than with PWPD may indicate that water organized in finer structure (bound to matrix) provides lower acoustic impedance than water in larger pores, which is yet to be investigated thoroughly. RELEVANCE STATEMENT: This study highlights the importance of future investigations exploring the relationship between QUS measures and all major components of the bone, including the collagenous matrix and water. Investigating the full potential of QUS and its validation facilitates a more affordable and accessible tool for bone health monitoring in clinics. KEY POINTS: • Ultrasound attenuation demonstrated significant positive correlations with bone mechanics and mineral density. • Ultrasound attenuation demonstrated significant negative correlations with porosity and bone water contents. • This study highlights the importance of future investigations exploring the relationship between QUS measures and all major components of the bone.

Biportal endoscopic-assisted cortical bone trajectory screw placement and lumbar interbody fusion.

BACKGROUND: Endoscopically assisted screw fixation with lumbar interbody fusion is rarely performed. We succeeded in implanting the cortical bone trajectory (CBT) screws under the guidance of unilateral biportal endoscopy (UBE). METHOD: We attempted endoscopically assisted screw fixation in a patient with degenerative spondylolisthesis. Through a third portal, ipsilateral CBT screws were implanted without complications. CONCLUSIONS: We successfully performed unilateral biportal endoscopic lumbar interbody fusion (ULIF) with CBT and reversed CBT screws. Compared with percutaneous pedicle screw (PPS) placement, this procedure is a minimally invasive, endoscopic alternative that allows precise screw placement.

Evaluation of cortical bone strength using a quantitative ultrasound measurement device in dogs.

This study was performed to evaluate cortical bone strength in dogs using a quantitative ultrasound measurement device. In this study, 16 clinically healthy dogs with no lameness underwent measurement of the ultrasound propagation velocity of cortical bone (namely, speed of sound [SOS]) at the radius and tibia. Additionally, computed tomography examination with a calibration phantom was performed in 10 dogs. We calculated the bone mineral density (BMD) and Young's modulus from the computed tomography data using bone strength evaluation software. SOS, BMD, and Young's modulus were statistically compared between the radius and tibia. In addition, we examined the correlation between SOS and BMD and between SOS and Young's modulus. We also examined the correlation between SOS and age in the 13 dogs whose age was known. BMD and Young's modulus were not significantly different between the radius and tibia, but SOS was significantly different (P<0.05). Moreover, SOS and BMD showed a positive correlation in both radius and tibia. Similarly, SOS and Young's modulus showed a positive correlation. In addition, SOS and age showed a strong positive correlation (radius: r=0.77, P<0.05, tibia: r=0.83, P<0.05). Our finding that SOS of the radius and tibia cortical bone was correlated with BMD and Young's modulus indicates that quantitative ultrasound can be useful for evaluating cortical bone strength in dogs.