A novel low shrinkage dimethacrylate monomer as an alternative to BisGMA for adhesive and resin-based composite applications.

The aim of this study was to develop a mixture of dimethacrylate isomers (PG6EMA) as a potential monomer for dental adhesives and composites. PG6EMA was synthesized de novo and characterized in the presence of ethanol (3%, 6% or 9%). BisGMA/TEGDMA (BTEG, 50/50 wt.%) was used as the resin control. Composites were formulated with 60 wt.% of either PG6EMA or BisGMA (40 wt.% TEGDMA and 70 wt.% filler). DMPA (0.2 wt.%) and DPI-PF6 (0.4 wt.%) were added as photoinitiators, irradiated with a mercury arc lamp (320-500 nm, 500 mW/cm2; Acticure). All materials were tested for polymerization kinetics (near-infrared), viscosity (η) and storage modulus (G', oscillatory rheometry). The composites were further characterized for water sorption/solubility, wet/dry flexural strength/modulus and polymerization stress. Data were analyzed with one-way ANOVA/Tukey's test (α = 0.05). The PG6EMA resins showed lower rates of polymerization compared with BTEG (p = 0.001) but high degrees of conversion (p = 0.002). Solvent concentration did not affect RPMAX but the 6% and 9% mixtures showed higher final DC, likely due to reduced viscosity. PG6EMA had much higher viscosity than BTEG (p <0.001) and lower G' (p = 0.003). Composites modified with PG6EMA have slower polymerization rates (p = 0.001) but higher final DC (p = 0.04) than the control. PG6EMA/TEGDMA showed lower dry/wet flexural strength and comparable dry modulus. The PG6EMA/TEGDMA composite showed a 18.4% polymerization stress reduction compared to the BTEG composite. Both base monomers had similar WS/SL and G'. Within its limitations, this study demonstrated that the newly synthesized PG6EMA was a viable alternative to BisGMA in dental composites.

Influence of light-polymerizing units and zirconia on the physical, chemical and biological properties of self-adhesive resin cements.

BACKGROUND: Self-adhesive resin cements (SARCs) are widely used for fixed prostheses, but incomplete cleaning near the gingival margin can cause inflammation. However, the factors influencing cement properties and the biological response of gingival fibroblasts to cement eluates are not well understood. This study examines the impact of two light-polymerizing units (LPUs) on the physical and chemical properties of two SARCs under simulated clinical conditions, as well as the subsequent response of human gingival fibroblasts (hGFs) to these eluates. METHODS: Dental cement discs of SARCs were polymerized using Kerr DemiPlus and 3 M Elipar DeepCure-S LED LPUs with or without a 2-mm thick zirconia screen. Physical properties (microhardness, surface roughness, residual monomers) were evaluated. hGFs' cell viability, wound healing potency, and gene expression were assessed. RESULTS: Both Maxcem and RelyX exhibited reduced microhardness and increased surface roughness when polymerized through zirconia or with DemiPlus LPU. Higher residual monomers (HEMA and GDMA in Maxcem; TEGDMA in RelyX) concentration was observed with DemiPlus and zirconia polymerization. Maxcem polymerized with DemiPlus exhibited lower cell viability, impaired healing, and altered gene expression in hGFs compared to those polymerized with Elipar LPU. Gene expression changes included downregulated NRF2 and HO-1 and upregulated CCR-3. CONCLUSIONS: Light-polymerizing Maxcem through zirconia with DemiPlus LPU compromised SARCs' properties, leading to higher residual monomers and negatively impacting hGFs' viability, healing, and gene expression. Careful material selection and polymerization techniques are crucial to minimize adverse effects on surrounding tissues. CLINICAL SIGNIFICANCE: Clinicians should exercise caution when using LPUs and SARCs, especially when polymerizing through zirconia. This will help optimize the physical and chemical properties of SARCs and minimize potential adverse effects on the surrounding gingival soft tissues.

Copolymerized Polymers Based on Cyclodextrins and Cationic Groups Enhance Therapeutic Effect of Rebamipide in the N-Acetylcysteine-Treated Dry Eye Model.

Purpose: We aimed to prepare a ß-cyclodextrin (ß-CD) polymer using radical polymerization with co-monomers, 6-deoxy-6-(2-methacryloyloxyethylsuccinamide)-ß-cyclodextrin (CD-MSAm) and N,N,N-trimethyl-N-(2-hydroxy-3-metacryloyloxopropyl)-ammonium chloride (QA) to design cyclodextrins suitable for use in ophthalmology. In addition, we evaluated their solubility and inclusion properties with rebamipide (REB), a poorly soluble drug, and investigated the usefulness of the ß-CD polymer and REB (REB@CDQA) combination in treating dry eye. Methods: The ß-CD polymer (CD-MSAm-co-QA, CDQA) based on CD-MSAm/QA was prepared via radical polymerization, and the usefulness of REB@CDQA in treating dry eye was evaluated using a rabbit treated with N-acetylcysteine (dry eye model). Results: The solubility of the CDQA powder was higher than that of the ß-CD powder, and 80 nm colloids were observed in the CDQA solution. No corneal toxicity was observed in human corneal epithelial cells or rat corneas treated with 0.2% CDQA solution. The levels of REB dissolved in the CDQA solution were higher than those of the ß-CD solution. Moreover, the application of the CDQA solution enhanced REB retention in the cornea and attenuated the transcorneal penetration of REB. In addition, instillation of REB@CDQA enhanced the volume of the lacrimal fluid and normalized the reduced mucin levels in the dry eye model. The extent of tear film breakup was attenuated by REB@CDQA instillation. Conclusion: The CDQA solution enhanced the solubility of REB, and the combination of CDQA and REB enhanced the drug content in the corneal tissue. Moreover, the therapeutic effect on dry eye was higher than that of REB suspensions without CDQA.

Development of a Human Recombinant Collagen for Vat Polymerization-Based Bioprinting.

In light-based 3D-bioprinting, gelatin methacrylate (GelMA) is one of the most widely used materials, as it supports cell attachment, and shows good biocompatibility and degradability in vivo. However, as an animal-derived material, it also causes safety concerns when used in medical applications. Gelatin is a partial hydrolysate of collagen, containing high amounts of hydroxyproline. This causes the material to form a thermally induced gel at ambient temperatures, a behavior also observed in GelMA. This temperature-dependent gelation requires precise temperature control during the bioprinting process to prevent the gelation of the material. To avoid safety concerns associated with animal-derived materials and reduce potential issues caused by thermal gelation, a recombinant human alpha-1 collagen I fragment was expressed in Komagataella phaffii without hydroxylation. The resulting protein was successfully modified with methacryloyl groups and underwent rapid photopolymerization upon ultraviolet light exposure. The developed material exhibited slightly slower polymerization and lower storage modulus compared to GelMA, while it showed higher stretchability. However, unlike the latter, the material did not undergo physical gelation at ambient temperatures, but only when cooled down to below 10°C, a characteristic that has not been described for comparable materials so far. This gelation was not caused by the formation of triple-helical structures, as shown by the absence of the characteristic peak at 220 nm in CD spectra. Moreover, the developed recombinant material facilitated cell adherence with high cell viability after crosslinking via light to a 3D structure. Furthermore, desired geometries could be easily printed on a stereolithographic bioprinter.

Enhancing craniofacial bone tissue engineering strategy: integrating rapid wet chemically synthesised bioactive glass with photopolymerized resins.

BACKGROUND: Craniofacial bone regeneration represents a dynamic area within tissue engineering and regenerative medicine. Central to this field, is the continual exploration of new methodologies for template fabrication, leveraging established bio ceramic materials, with the objective of restoring bone integrity and facilitating successful implant placements. METHODS: Photopolymerized templates were prepared using three distinct bio ceramic materials, specifically a wet chemically synthesized bioactive glass and two commercially sourced hydroxyapatite variants. These templates underwent comprehensive characterization to assess their physicochemical and mechanical attributes, employing techniques including Fourier transform infrared spectroscopy, scanning electron microscopy, and nano-computed tomography. Evaluation of their biocompatibility was conducted through interaction with primary human osteoblasts (hOB) and subsequent examination using scanning electron microscopy. RESULTS: The results demonstrated that composite showed intramolecular hydrogen bonding interactions with the photopolymer, while computerized tomography unveiled the porous morphology and distribution within the templates. A relatively higher porosity percentage (31.55 ± 8.70%) and compressive strength (1.53 ± 0.11 MPa) was noted for bioactive glass templates. Human osteoblast cultured on bioactive glass showed higher viability compared to other specimens. Scanning micrographs of human osteoblast on templated showed cellular adhesion and the presence of filopodia and lamellipodia. CONCLUSION: In summary these templates have the potential to be used for alveolar bone regeneration in critical size defect. Photopolymerization of bioceramics may be an interesting technique for scaffolds fabrication for bone tissue engineering application but needs more optimization to overcome existing issues like the ideal ratio of the photopolymer to bioceramics.

Integrative experimental and computational analysis of the impact of KGM's polymerization degree on wheat starch's pasting and retrogradation characteristics.

This study investigated the influence of Konjac Glucomannan (KGM) with varying degrees of polymerization (DKGMx) on the gelatinization and retrogradation characteristics of wheat starch, providing new insights into starch-polysaccharide interactions. This research uniquely focuses on the effects of DKGMx, utilizing multidisciplinary approaches including Rapid Visco Analysis (RVA), Differential Scanning Calorimetry (DSC), rheological testing, Low-Field Nuclear Magnetic Resonance (LF-NMR), and molecular simulations to assess the effects of DKGMx on gelatinization temperature, viscosity, structural changes post-retrogradation, and molecular interactions. Our findings revealed that higher degrees of polymerization (DP) of DKGMx significantly enhanced starch's pasting viscosity and stability, whereas lower DP reduced viscosity and interfered with retrogradation. High DP DKGMx promoted retrogradation by modifying moisture distribution. Molecular simulations revealed the interplay between low DP DKGMx and starch molecules. These interactions, characterized by increased hydrogen bonds and tighter binding to more starch chains, inhibited starch molecular rearrangement. Specifically, low DP DKGMx established a dense hydrogen bond network with starch, significantly restricting molecular mobility and rearrangement. This study provides new insights into the role of the DP of DKGMx in modulating wheat starch's properties, offering valuable implications for the functional improvement of starch-based foods and advancing starch science.

Molecularly Imprinted Microspheres in Active Compound Separation from Natural Product.

Molecularly Imprinted Microspheres (MIMs) or Microsphere Molecularly Imprinted Polymers represent an innovative design for the selective extraction of active compounds from natural products, showcasing effectiveness and cost-efficiency. MIMs, crosslinked polymers with specific binding sites for template molecules, overcome irregularities observed in traditional Molecularly Imprinted Polymers (MIPs). Their adaptability to the shape and size of target molecules allows for the capture of compounds from complex mixtures. This review article delves into exploring the potential practical applications of MIMs, particularly in the extraction of active compounds from natural products. Additionally, it provides insights into the broader development of MIM technology for the purification of active compounds. The synthesis of MIMs encompasses various methods, including precipitation polymerization, suspension polymerization, Pickering emulsion polymerization, and Controlled/Living Radical Precipitation Polymerization. These methods enable the formation of MIPs with controlled particle sizes suitable for diverse analytical applications. Control over the template-to-monomer ratio, solvent type, reaction temperature, and polymerization time is crucial to ensure the successful synthesis of MIPs effective in isolating active compounds from natural products. MIMs have been utilized to isolate various active compounds from natural products, such as aristolochic acids from Aristolochia manshuriensis and flavonoids from Rhododendron species, among others. Based on the review, suspension polymerization deposition, which is one of the techniques used in creating MIPs, can be classified under the MIM method. This is due to its ability to produce polymers that are more homogeneous and exhibit better selectivity compared to traditional MIP techniques. Additionally, this method can achieve recovery rates ranging from 94.91% to 113.53% and purities between 86.3% and 122%. The suspension polymerization process is relatively straightforward, allowing for the effective control of viscosity and temperature. Moreover, it is cost-effective as it utilizes water as the solvent.

Klebsiella LPS O1-antigen prevents complement-mediated killing by inhibiting C9 polymerization.

The Gram-negative bacterium Klebsiella pneumoniae is an important human pathogen. Its treatment has been complicated by the emergence of multi-drug resistant strains. The human complement system is an important part of our innate immune response that can directly kill Gram-negative bacteria by assembling membrane attack complex (MAC) pores into the bacterial outer membrane. To resist this attack, Gram-negative bacteria can modify their lipopolysaccharide (LPS). Especially the decoration of the LPS outer core with the O-antigen polysaccharide has been linked to increased bacterial survival in serum, but not studied in detail. In this study, we characterized various clinical Klebsiella pneumoniae isolates and show that expression of the LPS O1-antigen correlates with resistance to complement-mediated killing. Mechanistic data reveal that the O1-antigen does not inhibit C3b deposition and C5 conversion. In contrast, we see more efficient formation of C5a, and deposition of C6 and C9 when an O-antigen is present. Further downstream analyses revealed that the O1-antigen prevents correct insertion and polymerization of the final MAC component C9 into the bacterial membrane. Altogether, we show that the LPS O1-antigen is a key determining factor for complement resistance by K. pneumoniae and provide insights into the molecular basis of O1-mediated MAC evasion.

Changes in the surface texture of pre-polymerized acrylic resin pediatric crowns following acidulated phosphate fluoride application.

This study aimed to investigate the effect of acidulated phosphate fluoride (APF) application on filler-free polymethyl methacrylate (PMMA)-based resin blocks for computer-aided design/computer-aided manufacturing (CAD-CAM), focusing on their use in pediatric crowns. Three types of PMMA-based blocks for CAD-CAM were evaluated, and a composite resin block for CAD-CAM was used as a control. Statistical analysis (p<0.05) of the data revealed that all PMMA-based blocks showed significantly higher gloss levels than the composite resin blocks. Two PMMA-based blocks also demonstrated significantly lower Ra and Sa values. SEM images showed no irregular changes in the surface properties of the PMMA-based blocks compared to those of the composite resin block. These results are significant in meeting the increasing demand for esthetic restorative treatments in pediatrics, where APF is commonly used for caries prevention. PMMA-based resin blocks for CAD-CAM are an effective alternative to prevent esthetic degradation from gloss reduction and plaque accumulation.

Effects of minimally invasive endodontic access cavity in molar teeth on polymerization, porosity and fracture resistance.

Minimally invasive access cavities have been proposed in the last decade to reduce tooth tissue loss during endodontic treatment and mitigate compromised fracture resistance of endodontically treated teeth. Fracture resistance of molars with different types of access cavity design may be affected by restorative materials and aging. Insufficient literature data exist on the effect of cavity design and type of restorative materials on restorative aspects such as material adaptation or photo-polymerization in restricted access cavities. This study analyses quality of polymerization, material adaptation and fracture resistance of molars with different types of access cavities restored with glass-ionomer, high-viscosity fiber-reinforced bulk-fill and nanofilled resin composite. Plastic molar teeth with truss (TREC) and traditional endodontic access cavity (TEC) were restored with nanofilled composite (Filtek Supreme), glass-ionomer Fuji IX and Filtek or fiber-reinforced everX Posterior and Filtek. Porosity was determined using microcomputer tomography and the degree of conversion of resin-based materals using micro-Raman spectroscopy. Human molars prepared and restored in the same way were used for fracture resistance testing at baseline and after thermocycling. The results demonstrate that high-viscosity fiber-reinforced composite was difficult to adapt in TREC cavity leading to greater porosity than Filtek or Fuji. TREC design did not affect composite polymerization and led to higher fracture resistance of restored molars compared to TEC but also more unrestorable fractures.

Modular Structure and Polymerization Status of GABAA Receptors Illustrated with EM Analysis and AlphaFold2 Prediction.

Type-A γ-aminobutyric acid (GABAA) receptors are channel proteins crucial to mediating neuronal balance in the central nervous system (CNS). The structure of GABAA receptors allows for multiple binding sites and is key to drug development. Yet the formation mechanism of the receptor's distinctive pentameric structure is still unknown. This study aims to investigate the role of three predominant subunits of the human GABAA receptor in the formation of protein pentamers. Through purifying and refolding the protein fragments of the GABAA receptor α1, ß2, and γ2 subunits, the particle structures were visualised with negative staining electron microscopy (EM). To aid the analysis, AlphaFold2 was used to compare the structures. Results show that α1 and ß2 subunit fragments successfully formed homo-oligomers, particularly homopentameric structures, while the predominant heteropentameric GABAA receptor was also replicated through the combination of the three subunits. However, homopentameric structures were not observed with the γ2 subunit proteins. A comparison of the AlphaFold2 predictions and the previously obtained cryo-EM structures presents new insights into the subunits' modular structure and polymerization status. By performing experimental and computational studies, a deeper understanding of the complex structure of GABAA receptors is provided. Hopefully, this study can pave the way to developing novel therapeutics for neuropsychiatric diseases.

In situ biocatalytic ATP regulated, transient supramolecular polymerization.

Temporal control over self-assembly processes is a highly desirable attribute that is efficiently exhibited by biological systems, such as actin filaments. In nature, various proteins undergo enzymatically catalysed chemical reactions that kinetically govern their structural and functional properties. Consequently, any stimuli that can alter their reaction kinetics can lead to a change in their growth or decay profiles. This underscores the urgent need to investigate bioinspired, adaptable and controllable synthetic materials. Herein we intend to develop a general strategy for controlling the growth and decay of self-assembled systems via enzymatically coupled reactions. We achieve this by the coupling of enzymes phosphokinase/phosphatase with a bolaamphiphilic cationic chromophore (PDI) which selectively self-assembles with ATP and disassembles upon its enzymatic hydrolysis. The aggregation process is efficiently regulated by the controlled in situ generation of ATP, through enzymatic reactions. By carefully managing the ATP generating components, we realize precise control over the self-assembly process. Moreover, we also show self-assembled structures with programmed temporal decay profiles through coupled enzymatic reactions of ATP generation and hydrolysis, essentially rendering the process dissipative. This work introduces a novel strategy to generate a reaction-coupled one-dimensional nanostructure with controlled dimensions inspired by biological systems.

Fabrication and properties of temperature-responsive imprinted sensors based on fluorescently labeled yeast cells via MVL ATRP.

Temperature-responsive yeast cell-imprinted sensors (CIPs/AuNPs/Ti3C2Tx/AuNPs/Au) were prepared based on fluorescein isothiocyanate labeled yeast cells (FITC-yeast) via metal-free visible-light-induced atom transfer radical polymerization (MVL ATRP). Here, N-isopropyl acrylamide (NIPAM) was used as a temperature-responsive functional monomer, α-methacrylic acid (MAA) was chosen as an auxiliary functional monomer, N,N'-methylene bisacrylamide (MBA) was used as a cross-linker, and FITC-yeast was selected as both a template and photocatalyst. Under the optimal conditions, the detection range of the yeast cell-imprinted sensor toward yeast cells was 1.0 × 102 to 1.0 × 109 cells per mL, and the detection limit was 11 cells per mL (S/N = 3), with a linear equation of ΔI (µA) = 8.44 log[C (cells per mL)] + 7.62 (R2 = 0.993). The sensor showed good selective recognition in the presence of interfering substances such as autolyzed yeast cells (AY), dead yeast cells (DY), human mammary epithelial cells (MCF-10A), human breast cancer cells (MCF-7) and Escherichia coli (EC). The sensor also had good consistency and reproducibility. Finally, spiked recovery experiments were performed to investigate the recognition of yeast cells in the actual sample using the yeast cell-imprinted sensor. The spiked recoveries were all in the range of 98.5-108.0%, and the RSD values were all less than 4%, indicating that the sensor had good application prospects.

Optimization of PET depolymerization for enhanced terephthalic acid recovery from commercial PET and post consumer PET-bottles via low-temperature alkaline hydrolysis.

The increasing demand for plastic has resulted in a surge in plastic waste production. Polyethylene terephthalate (PET), commonly used in beverage bottle manufacturing, is only partially recycled, with an estimated recycling rate of just 28.4% in 2019. This accumulation of plastic waste is harmful to the environment and living organisms, necessitating effective recycling methods for PET waste. One promising method is alkaline hydrolysis using NaOH, which can break down PET into its monomer components, terephthalic acid (TPA) and ethylene glycol (EG). This process not only recycles PET efficiently but also manages contaminants effectively, producing high-quality TPA, supporting the development of a circular economy. This study looks into PET depolymerization via alkaline hydrolysis at low temperature by investigating effects of various factors: pH levels, water to ethanol ratio, NaOH concentration, NaOH to PET ratio, reaction time, PET size, reusability of unreacted PET, air plasma pretreatment of PET, and different kinds of PET. Promisingly, PET conversion rates of over 90% and a TPA purity of 99.6% were achieved in this study highlighting the efficacy of alkaline hydrolysis in depolymerizing post-consumer PET waste. Ultimately, this research advances sustainable plastic waste management and supports the integration of PET into a circular economy framework.

Physicochemical properties of flowable composites using isobornyl methacrylate as diluent monomer.

OBJECTIVE: this study sought to evaluate the effect of isobornyl methacrylate (IBOMA) as a diluent monomer on the physicochemical properties of experimental flowable resin composites. METHODOLOGY: the organic resin matrix of a modal flowable resin composite was formulated with 50 wt.% of bisphenol-A-glycidyl methacrylate (Bis-GMA) and 50 wt.% of a diluent monomer, in which IBOMA was used as a combining or substituent diluent monomer to triethylene glycol dimethacrylate (TEGDMA). The resin matrices were filled with 55 wt.% particles, of which 10 wt.% was 0.05-µm fumed silica, and 45 wt.% was 0.7-µm BaBSiO2 glass. Polymerization shrinkage stress (PSS; n=10), degree of conversion (DC; n=3), maximum rate of polymerization (Rpmax; n=3), film thickness (FT; n=10), sorption (Wsp; n=10), solubility (Wsl; n=10), flexural strength (FS; n=10), flexural modulus (FM; n=10), Knoop microhardness (KH; n=10), and microhardness reduction after chemical softening (HR; n=10) were evaluated. Data were analyzed using one-way ANOVA, followed by Tukey's test (α=0.05; ß=0.2). RESULTS: the results showed that the substitution or addition of IBOMA reduced FT (p=0.001), PSS (p=0.013), Rpmax (p=0.001), DC (p=0.001), FM (p=0.006) Wsp (p=0.032), and Wsl (p=0.021). However, when used as a complete substituent, IBOMA demonstrated significantly lower FS (p=0.017) and KH (p=0.008), while TEGDMA demonstrated significantly lower HR (p=0.022). CONCLUSION: the flowable composite containing IBOMA combined with TEGDMA showed no effect in KH and FS and effectively reduced the PSS, RP, FT, Wsp, and Wsl. However, it showed a reduction in DC, FS, and an increase in HR.

Efficient catalytic removal of phenolic pollutants by laccase from Coriolopsis gallica: Binding interaction and polymerization mechanism.

Laccase is a green catalyst that can efficiently catalyze phenolic pollutants, and its catalytic efficiency is closely related to the interaction between enzyme and substrates. To investigate the binding effects between enzyme and phenolic pollutants, phenol, p-chlorophenol, and bisphenol A were used as substrates in this study. We focused on the removal and catalytic mechanism of these pollutants in water using yellow laccase derived from Coriolopsis gallica. The enzymatic catalytic products were characterized using Ultraviolet-Visible Absorption Spectroscopy (UV-Vis), Fourier Transform Infrared Spectroscopy (FTIR), and High-Resolution Mass Spectrometry (HRMS), and the catalytic mechanism of laccase on phenolic pollutants was further explored by molecular docking. Based on the structural characterization and molecular docking results, the possible polymerization pathways of these phenolic compounds were speculated. Laccase catalyzed phenol to produce phenolic hydroxyl radicals, their para-radicals, and ortho-radicals, which polymerized to form oligomers linked by benzene­oxygen-benzene and benzene-benzene. P-chlorophenol produced phenolic hydroxyl radicals and their ortho-radicals, polymerizing to form oligomers connected by benzene­oxygen-benzene or benzene-benzene. The CC bond of the isopropyl group of bisphenol A broke to formed an intermediate product, which was further polymerized to formed a benzene­oxygen-benzene linked oligomer.

Mini-review on lignin-based self-healing polymer.

Lignin, a biopolymer derived from plant biomass, is recognized as a highly promising substance for developing self-healing polymers owing to its dynamic linkages and functional groups. This paper provides a thorough review of lignin-based self-healing polymer, from the process of extracting lignin, chemical modification, synthesis techniques such as via reversible addition-fragmentation chain transfer (RAFT) polymerization, crosslinking with polymers like polyvinyl alcohol (PVA) and chitosan, and reactions with isocyanates to create lignin-based networks with reversible interactions. This work also summarizes the optimization of self-healing ability, such as including dynamic copolymers, encapsulating healing agents like dicyclopentadiene and polycaprolactone (PCL), and chain extenders with disulfide or Diels-Alder (DA) moieties. The material's characterization focuses on its capacity to recover via hydrogen bonding and dynamic re-associations, improved mechanical properties from lignin's rigid structure, and enhanced temperature resistance. Primary obstacles involve the optimization of lignin extraction, enhancement of polymer compatibility, and the establishment of efficient procedures for synthesis and characterization. Overall, lignin shows great potential as a renewable component of self-healing polymers, with plenty of opportunities for further development.

Sustainable chitin-derived elastomers via grafting strategy with tunable mechanical and adhesion properties.

With increasing environmental awareness and the pursuit of sustainable development goals, environmentally friendly sustainable thermoplastic elastomers (TPEs) derived from natural resources are highly desired to replace traditional TPEs. However, preparing sustainable TPEs with high mechanical properties and multifunctionality from biobased feedstocks remains a significant challenge. In this work, a series of chitin-graft-poly(acrylamide-co-2-ethylhexyl acrylate) (Chitin-g-P(AM-co-EHA)) copolymers were synthesized through reversible addition-fragmentation chain transfer (RAFT) polymerization. The tensile strength of Chitin-g-P(AM-co-EHA) copolymers can be tuned over a wide range from 1.0 to 7.3 MPa by adjusting the chitin and PAM contents. Benefiting from the brush-like architecture, Chitin-g-P(AM-co-EHA) copolymer exhibits improved mechanical properties over its linear counterparts. Moreover, these Chitin-g-P(AM-co-EHA) copolymers show good adhesion performance on different substrates. The shear strength can achieve 7.5 MPa for Chitin0.8-PAM50, which is high enough for commercial applications. The combination of chitin and grafting strategy can promote the development of strong chitin-based sustainable elastomers. This approach can be further utilized to design novel high-performance biobased elastomers and adhesives derived from natural resources.

Lignin hydrogel sensor with anti-dehydration, anti-freezing, and reproducible adhesion prepared based on the room-temperature induction of zinc chloride-lignin redox system.

In recent years, flexible sensors constructed mainly from hydrogels have received increasing attention. However, conventional hydrogels need to be prepared by high-temperature or radiation-induced polymerization reactions, which limits their practical applications due to their suboptimal electrical conductivity and weak mechanical properties. In this paper, using sodium lignosulfonate as the raw material, a dynamic catechol-quinone redox system formed by lignin­zinc ions was constructed to initiate rapid free radical polymerization of acrylamide (AM) monomer at room temperature. In addition, Deep eutectic solvent (DES) can form a strong hydrogen bonding network within the molecules and between the molecules of the hydrogel, resulting in a hydrogel with good tensile properties (hydrogel elongation at break of 727.19 %, breaking strength of 84.09 kPa), and provides the hydrogel with high electrical conductivity, anti-dehydration, anti-freezing, and anti-bacterial properties. Meanwhile, the addition of lignin also improved the adhesion and UV resistance of the hydrogel. This hydrogel assembled into a flexible sensor can sense various small and large amplitude movements such as nodding, smiling, frowning, etc., and has a wide range of applications in flexible sensors.

Revitalizing biopolymers to prepare temperature-resistant and salt-tolerant filtrate reducer by combining light-driven lignin depolymerization and subsequent photopolymerization on MIL-100(Fe)-NH2(20) photocatalyst.

For the first time, this study integrate the light-driven depolymerization/activation of industrial grade sodium lignosulfonate and its subsequent photo-induced radical polymerization with acrylamide (AM) and 2-acrylamido-2-methylpropanesulfonic acid (AMPS) into one-pot using MIL-100(Fe)-NH2(20) as a photocatalyst to synthesize fluid loss agent LSMP. Due to the significant hydrogen bonding effect, the agent owns excellent rheological and filtration properties. The filtrate volumes of drilling fluids containing 2.0 wt% agent before and after aging at 150 °C are only 3.6 and 4.6 mL, reducing by 85.0 % and 88.5 %, respectively, compared with pure fluids. Even at high temperatures and high salinity, LSMP still gives stunning performances with significant filtrate volumes decline of 96.58 % and 86.52 % under erosion of 25 wt% NaCl and 2.0 wt% CaCl2, separately. Meanwhile, the filtration reduction mechanism of LSMP is presented, and the probable photocatalytic mechanism is also explored: 1, under depolymerization process, the selective cleavage of ubiquitous C - O/C - C linkage bonds (ß-O-4, ß-5, α-O-4, ß-ß, 4-O-5, ß-1, dibenzodioxocin, etc.) occur, accompanied by the aromatic rings intact; 2, with the action of photo-induced carriers generated on MIL-100(Fe)-NH2(20), absorbed photons are transformed into thermal energy and the radical polymerization of green synthesis are ultimately achieved.