Compound-Specific Isotope Analysis Provides Direct Evidence for Identifying the Source of Residual Pesticides Diazinon and Procymidone in the Soil-Plant System.

Compound-specific isotope analysis stands as a promising tool for unveiling the behavior of pesticides in agricultural environments. Using the commercial formulations of persistent fungicide procymidone (PRO) and less persistent insecticide diazinon (DIA), respectively, we analyzed the concentration and carbon isotope composition (δ13C) of the residual pesticides through soil incubation experiments in a greenhouse (for 150 days) and lab conditions (for 50-70 days). Our results showed that the magnitude of δ13C variation depends on pesticide specificity, in which PRO in the soil exhibited little variation in δ13C values over the entire incubation times, while DIA demonstrated an increased δ13C value, with the extent of δ13C variability affected by different spiking concentrations, plant presence, and light conditions. Moreover, the pesticides extracted from soils were isotopically overlapped with those from crop lettuce. Ultimately, the isotope composition of pesticides could infer the degradation and translocation processes and might contribute to identifying the source(s) of pesticide formulation in agricultural fields.

Vortex-assisted dispersive micro-solid-phase extraction using silica-supported Fe2O3-modified khat (Catha edulis) biochar nanocomposite followed by GC-MS for the determination of organochlorine pesticides in juice samples.

In this paper, dispersive micro-solid phase extraction technique was developed for the purpose of extracting and preconcentrating organochlorine pesticide residues in juice samples before their separation and quantitative analysis by gas chromatography-mass spectrometry. A sorbent composed of a silica-supported Fe2O3-modified khat leftover biochar nanocomposite (SiO2-Fe2O3-KLBNC) was implemented in the process. To improve the dispersion of the sorbent in the solution, vortex mixer was employed. Experimental parameters influencing the performance of the method were optimized, and the optimal conditions were established. With these conditions, linear dynamic ranges ranged from 0.003 to 100.0 ng/mL were achieved, with a correlation coefficient (r2) ≥ 0.9981. The limits of detection and quantification, determined by signal-to-noise ratios of 3 and 10, respectively, were found to be in the ranges of 0.001-0.006 ng/mL and 0.003-0.020 ng/mL. Intra- and inter-day precision, values ranging from 0.3-4.8% and 1.7-5.2% were obtained, respectively. The matrix-matched extraction recoveries demonstrated favorable outcomes, falling within the range of 83.4-108.3%. The utilization of khat leftover as an adsorbent in contemporary sample preparation methodologies offers a cost-effective alternative to the currently available, yet expensive, adsorbents. This renders it economically viable, particularly in resource-constrained regions, and is anticipated to witness widespread adoption in the coming future.

Sensitive colorimetric and fluorescence dual-mode detection of thiophanate-methyl based on spherical Fe3O4/GONRs composite nanozyme.

Pesticide detection based on nanozyme is largely limited in terms of the variety of pesticides. Herein, a spherical and well-dispersed Fe3O4/graphene oxide nanoribbons (Fe3O4/GONRs) composite nanozyme was applied to firstly develop an enzyme-free and sensitive colorimetric and fluorescence dual-mode detection of thiophanate-methyl (TM). The synthesized Fe3O4/GONRs possess excellent dual enzyme-like activities (peroxidase and catalase) and can catalyze H2O2 to oxidize 3,3',5,5'-tetramethylbenzidine (TMB) into oxidized TMB (oxTMB). We found that Fe3O4/GONRs can adsorb TM through the synergistic effect of multiple forces, thereby inhibiting the catalytic activities of nanozyme. This inhibition can modulate the transformation of TMB to oxTMB, producing dual responses of absorbance decrease (oxTMB) and fluorescence enhancement (TMB). The limits of detection (LODs) of TM were 28.1 ng/mL (colorimetric) and 8.81 ng/mL (fluorescence), respectively. Moreover, the developed method with the recoveries of 94.8-100.8% also exhibited a good potential application in the detection of pesticides residues in water and food samples.

Green synthesis of superhydrophilic resin/graphene oxide for efficient analysis of multiple pesticide residues in fruits and vegetables.

The escalating use of pesticides on fruits and vegetables has raised concerns about potential health risks. Therefore, we developed a superhydrophilic resin/graphene oxide (SR/GO) with rich adsorption interactions using an eco-friendly synthetic approach. SR/GO demonstrated excellent hydrophilicity, ensuring optimal contact with aqueous sample matrices. The multiple adsorption interactions, including π-π conjugation, hydrogen bonding, and electrostatic adsorption, facilitated multi-pesticide residue co-extraction. The synthesized SR/GO was applied to a miniaturized centrifugation-accelerated pipette-tip extraction method, coupled with high-performance liquid chromatography. The optimized method exhibited low consumption (15.0 mg adsorbent), and high efficiency, with low detection limits (1.4-2.9 ng g-1) and high recoveries (75.3-113.0%). Water-compatible SR/GO, along with a miniaturized extraction process, showcases a potent analytical approach for pesticide residue analysis in fruits and vegetables. The significance of this method lies in its ability to ensure agricultural and food safety by using a low-cost and efficient multi-pesticide residue analytical strategy.

Multimode ultrasonic-assisted decontamination of fruits and vegetables: A review.

Fruits and vegetables (F&V) are a significant part of our diet consumption. Microbial and pesticide residues are the predominant safety hazards of F&V consumption. Ordinary water washing has a very limited effect on removing microorganisms and pesticide residues and requires high water usage. Ultrasound, as an environmentally friendly technology, shows excellent potential for reducing microbial contamination and pesticide residue. This paper summarizes the research on ultrasound application in F&V washing, including the removal of microbial and pesticide residues and the comprehensive effect on their physicochemical characteristics. Furthermore, multimode ultrasonic-assisted techniques like multi-frequency and sequential ultrasound, combined with novel and conventional methods, can enhance the ultrasound-based effect and be more effective and sustainable in preventing F&V from microbial contamination. Overall, this work explicitly establishes the background on the potential for ultrasound cleaning and disinfection in the food industry as a green, effective, and ultimate method of preventing foodborne illnesses.

Based on metabolomics, chemometrics, and modern separation omics: Identifying key in-pathway and out-pathway points for pesticide residues during solid-state fermentation of baijiu.

By collecting real samples throughout the entire production process and employing chemometrics, metabolomics, and modern separation omic techniques, it unveiled the patterns of pesticide transfer during solid-state fermentation. The results indicated that 12 types of pesticide residues were prevalent during baijiu production, with organochlorine and carbamate pesticides being the most abundant in raw materials. After fermentation, organochlorine pesticides and pyrethroid pesticides exhibited higher content, while carbamate pesticides dominated in the final product. The pathways for pesticide input and elimination were identified, and the intricate mechanisms underlying these changes were further elucidated. Additionally, key control points were defined to facilitate targeted monitoring. The results indicated that pesticide residue primarily originates from raw materials and Daqu, whereas both solid-state fermentation and distillation processes were effective in reducing pesticide residues. The study offers valuable guidance for establishing pesticide residue standards in the context of baijiu production.

Pesticide Residues in Organic and Conventional Agricultural Soils across Europe: Measured and Predicted Concentrations.

During the growing season of 2021, 201 soil samples from conventionally and organically managed fields from 10 European countries and 8 cropping systems were taken, and 192 residues of synthetic pesticides were analyzed. Pesticide residues were found in 97% of the samples, and 88% of the samples contained mixtures of at least 2 substances. A maximum of 21 substances were found in conventionally managed fields, and a maximum of 12 were found in organically managed fields. The number and concentration of pesticide residues varied significantly between conventional and organic fields in 70 and 50% of the case study sites, respectively. Application records were available for a selected number of fields (n = 82), and these records were compared to the detected substances. Residues from 52% of the applied pesticides were detected in the soils. Only 21% of the pesticide residues detected in the soil samples were applied during the 2021 growing season. From the application data, predicted environmental concentrations of residues in soil were calculated and compared to the measured concentrations. These estimates turned out not to be accurate. The results of this study show that most European agricultural soils contain mixtures of pesticide residues and that current calculation methods may not reliably estimate their presence.

Greenhouse cultivation enhances pesticide bioaccumulation in cowpeas following repeated spraying.

Understanding pesticide residue patterns in crops is important for ensuring human health. However, data on residue accumulation and distribution in cowpeas grown in the greenhouse and open field are lacking. Our results suggest that acetamiprid, chlorantraniliprole, cyromazine, and thiamethoxam residues in greenhouse cowpeas were 1.03-15.32 times higher than those in open field cowpeas. Moreover, repeated spraying contributed to the accumulation of pesticide residues in cowpeas. Clothianidin, a thiamethoxam metabolite, was detected at 1.04-86.00 µg/kg in cowpeas. Pesticide residues in old cowpeas were higher than those in tender cowpeas, and the lower half of the plants had higher pesticide residues than did the upper half. Moreover, pesticide residues differed between the upper and lower halves of the same cowpea pod. Chronic and acute dietary risk assessments indicated that the human health risk was within acceptable levels of cowpea consumption. Given their high residue levels and potential accumulation, pesticides in cowpeas should be continuously assessed.

Beyond helium: hydrogen as a carrier gas in multiresidue pesticide analysis in fruits and vegetables by GC-MS/MS.

In this comprehensive study, we evaluated the feasibility of using hydrogen instead of helium as a carrier gas in a GC-MS/MS system for pesticide residue analysis, spanning three matrices: pepper, tomato, and zucchini. Initial assessments focused on the ion source's chemical inertness, employing nitrobenzene as a benchmark to monitor the hydrogenation process. A method with a duration of less than 12 minutes was developed, achieving good chromatographic peak resolution attributable to the enhanced chromatographic performance of hydrogen as a carrier gas. The study emphasized the optimization of system parameters, testing various ion source temperatures, detector voltages, and injection volumes. Sensitivity assessments, based on the DG-SANTE criteria, indicated that the majority of compounds were identifiable at a concentration of 5 µg kg-1 (81% in tomato, 84% in pepper and 73% in zucchini). Detailed validation for reproducibility, matrix effects, and linearity across 150 pesticides unveiled generally favorable outcomes, with a notable majority of compounds displaying low matrix effects, satisfactory linearity ranges and good reproducibility with most compounds returning a relative standard deviation (RSD) below 10%. When applied to 15 real samples, the hydrogen-based system's performance was juxtaposed against a helium-based counterpart, revealing that results are very comparable between both systems. This comparative approach highlights hydrogen's potential as a reliable and efficient carrier gas in pesticide residue analysis for routine food control laboratories, overcoming difficulties resulting from the lack of helium supplies.

Comparison of recovery efficiency and matrix effect reduction in pesticide residue analysis: QuEChERS with d-SPE, SPE, and FaPEx in apples and Korean cabbage.

QuEChERS is widely used for the analysis of pesticide residues. However, d-SPE, which is commonly utilized in QuEChERS, demonstrates lower clean-up effectiveness than that achieved using conventional SPE, leading to an inadequate reduction of matrix effects. Hence, methods, such as internal standards and matrix-matched calibration (MMC), are frequently employed to address matrix effects. The most effective way to minimize matrix effects is to enhance the clean-up efficiency. In this study, the analytical efficiencies of conventional QuEChERS, d-SPE, SPE, and FaPEx, a novel analytical method, were compared for the clean-up of apple and Korean cabbage samples. The proportion of test pesticides within the appropriate recovery range was 94-99% for QuEChERS, d-SPE, and SPE, while it was 80-95% for FaPEx. When evaluating the recovery results by group, the proportion of pesticides in group III (90-105%) was lower for FaPEx (3-70%) than that for d-SPE (85-92%) and SPE (79-89%). The matrix effect reduction was satisfactory for all clean-up methods, with more than 94% of the test pesticides showing low levels of matrix effects within ±20%. In FaPEx, over 98% of the test pesticides exhibited low matrix effects, indicating better reduction effects than in QuEChERS-based d-SPE and SPE. Method validation results at 0.01 and 0.1 mg kg-1 concentration levels using QuEChERS, SPE (PSA), and FaPEx (amine + C18) demonstrated that more than 95% of the test pesticides were within the appropriate recovery range. Overall, our study contributes to the development of efficient and reliable analytical methods for ensuring the safety and quality of agricultural products.

Detection methods, migration patterns, and health effects of pesticide residues in tea.

Due to its rich health benefits and unique cultural charm, tea drinking is increasingly popular with the public in modern society. The safety of tea is the top priority that affects the development of tea industry and the health of consumers. During the process of tea growth, pesticides are used to prevent the invasion of pests and diseases with maintaining high quality and stable yield. Because hot water brewing is the traditional way of tea consumption, water is the main carrier for pesticide residues in tea into human body accompanied by potential risks. In this review, pesticides used in tea gardens are divided into two categories according to their solubility, among which water-soluble pesticides pose a greater risk. We summarized the methods of the sample pretreatment and detection of pesticide residues and expounded the migration patterns and influencing factors of tea throughout the process of growth, processing, storage, and consumption. Moreover, the toxicity and safety of pesticide residues and diseases caused by human intake were analyzed. The risk assessment and traceability of pesticide residues in tea were carried out, and potential eco-friendly improvement strategies were proposed. The review is expected to provide a valuable reference for reducing risks of pesticide residues in tea and ensuring the safety of tea consumption.

The Open Pesticide Transition Library (oPestTL).

The identification of pesticide residues is a critical application in environmental and food safety analysis. The most common methods for pesticide residue detection and quantification are performed with liquid chromatography tandem mass spectrometry (LCMS) using instruments with varying architectures and characteristics. Pesticides have diverse structural and elemental compositions and often require laborious instrument-specific user optimization to identify ideal adducts and fragment ions. While pesticide transition libraries can be purchased from instrument vendors, little of this information exists in the public domain. The Open Pesticide Transition Library (oPestTL) is an effort to compile a comprehensive list of pesticide ion targets and fragments to facilitate the rapid development of screening methods for any LCMS hardware configuration. While a work that must inevitably evolve, the oPestTL library release detailed here contains over 4,000 individual transitions spread across seven separate LCMS platforms making it the largest openly available collection of pesticide methods ever assembled. The oPestTL library can be freely downloaded or interrogated through an open web application: https://proteomicsnews.shinyapps.io/oPestTLv104/.

An anti-scratch flexible SERS substrate for pesticide residue detection on the surface of fruits and vegetables.

We propose an anti-scratch flexible surface-enhanced Raman scattering substrate with arrayed nanocavity microstructures fabricated by colloidal lithography. The nanocavity microstructure of the substrate can well protect the inner gold nanoparticles during wipe sampling. The prepared flexible substrate was able to detect 4-aminothiophenol (4-ATP) with a concentration down to 1 fM. Furthermore, the substrate was used to detect 6-BA residues on the surface of apples and bean sprouts through wipe sampling, which shows great potential in the field of rapid on-site detection, especially in the detection of pesticide residues on the surface of fruits and vegetables.

Degradation mechanism and toxicity assessment of chlorpyrifos in milk by combined ultrasound and ultraviolet treatment.

The aim of this study was to compare the degradation kinetics of chlorpyrifos by treatment with ultrasound (US), ultraviolet radiation (UV) and a combination of both (US/UV), to evaluate the toxicity of the degradation products and the effect of the treatments on milk quality. US/UV markedly accelerated the degradation of chlorpyrifos. The half-life of chlorpyrifos by US/UV was 6.4 min, which was greatly shortened compared to the treatment with US or UV alone. Five degradation products were identified by GC-MS, and a degradation pathway for chlorpyrifos was proposed, based on density functional theory calculations. According to the luminescent bacteria test and predictions from a structure/activity relationship model, the toxicity of the degradation products was lower than that of chlorpyrifos. In addition, US/UV treatment had little effect on the quality of the treated milk. Therefore, US/UV can be used as a potential non-thermal processing method to degrade pesticide residues in milk.

Occurrence and human health risk assessment of mineral elements and pesticides residues in bee pollen.

Bee pollen contains a diversity of bioactive components. Nevertheless, since pollen is retrieved from a variety of plants, including the cultivated ones which are subjected to agrochemical treatments, its contamination is unavoidable. In this context, 45 samples of pollen were analysed with optimized analytical methods for trace and macro elements (ICP-MS), pesticides and metabolites residues (LC & GC-MS/MS) content. According to the results, potassium and iron were the most abundant in terms of concentration and frequency of detection, while the contribution of the most hazardous elements, such as lead, arsenic, cadmium and mercury, to the total concentration of trace elements was lower than 1%. For pesticides, coumaphos was the most frequently detected in the examined samples (22%), followed by propargite, azoxystrobin, dimethoate and cypermethrin. Non-carcinogenic health risk assessment demonstrated in the majority of cases negligible risk for adults and children. On the contrary, carcinogenic risk assessment considering a worst case scenario disclosed nickel and in less extent chromium and arsenic, as risk drivers, exhibiting in several samples carcinogenic risk values for adults above the safety threshold. Yet, regarding that both adults and children unlikely will daily consume such pollen quantities, especially on a long-term basis, an overestimation of risk should be appraised.

Sub-structure-based category formation for the prioritisation of genotoxicity hazard assessment for pesticide residues: Sulphonyl ureas.

In dietary risk assessment, residues of pesticidal ingredients or their metabolites need to be evaluated for their genotoxic potential. The European Food Safety Authority recommend a tiered approach focussing assessment and testing on classes of similar chemicals. To characterise similarity and to identify structural alerts associated with genotoxic concern, a set of chemical sub-structures was derived for an example dataset of 74 sulphonyl urea agrochemicals for which either Ames, chromosomal aberration or micronucleus test results are publicly available. This analysis resulted in a set of seven structural alerts that define the chemical space, in terms of the common parent and metabolic scaffolds, associated with the sulphonyl urea chemical class. An analysis of the available profiling schemes for DNA and protein reactivity shows the importance of investigating the predictivity of such schemes within a well-defined area of structural space. Structural space alerts, covalent chemistry profiling and physico-chemistry properties were combined to develop chemical categories suitable for chemical prioritisation. The method is a robust and reproducible approach to such read-across predictions, with the potential to reduce unnecessary testing. The key challenge in the approach was identified as being the need for pesticide-class specific metabolism data as the basis for structural space alert development.

Enantioselective determination of phenthoate enantiomers in plant-origin matrices using reversed-phase high-performance liquid chromatography-tandem mass spectrometry.

Phenthoate is a chiral organophosphate pesticide with a pair of enantiomers which differ in toxicity, behavior and insecticidal activity, and its acute toxicity on human health owing to the inhibition of acetylcholinesterase highlights the need for enantioselective detection of enantiomers. Therefore, this study aimed to establish a simple rapid method for separation and detection of phenthoate enantiomers in fruits, vegetables and grains. The enantiomers were separated using reversed-phase high-performance liquid chromatography-tandem mass spectrometry for the first time. Rapid chiral separation (within 9 min) of the target compound was achieved on a chiral OJ-RH column with the mobile phase of methanol-water = 85:15(v/v), at a flow rate of 1 ml/min and a column temperature of 30°C. Acetonitrile and graphitized carbon black were used as the extractant and sorbent for pretreatment, respectively. This method provides excellent linearity (correlation coefficient ≥0.9986), high sensitivity (limit of quantification 5 µg/kg and limit of detection <0.25 µg/kg), satisfactory mean recoveries (76.2-91.0%) and relative standard deviation (intra-day RSDs ranged from 2.0 to 7.9% and inter-day RSDs ranged from 2.4 to 8.4%). In addition, a field trial to explore the stereoselective degradation of phenthoate enantiomers in citrus showed that (-)-phenthoate degraded faster than its antipode, resulting in the relative accumulation of (+)-phenthoate.

Monitoring residue levels and dietary risk assessment of thiamethoxam and its metabolite clothianidin for Chinese consumption of Chinese kale.

BACKGROUND: Thiamethoxam is widely used to control pests in Chinese kale, popularly consumed leafy vegetables. The potential risk to the environment and human health has aroused much public concern. Therefore, it is important to investigate the degradation behavior, residue distribution and dietary risk assessment of thiamethoxam in Chinese kale. RESULTS: A sensitive analytical method for determination of thiamethoxam and its metabolite clothianidin residue in Chinese kale was established and validated through a quick, easy, cheap, effective, rugged, and safe (QuEChERS) technique with ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS). The recoveries were 85.4-101.2% for thiamethoxam and 79.5-108.1% for clothianidin, with the relative standard deviations (RSDs) of 0.9-10.2% and 1.8-6.0%, respectively. For the dissipation kinetics, the data showed that thiamethoxam in Chinese kale was degraded with the half-lives of 4.1 to 4.5 days. In the terminal residue experiments, the residues of thiamethoxam were 0.017-0.357 mg kg-1 after application 2-3 times with a preharvest interval (PHI) of 7 days under the designed dosages. The chronic and acute dietary exposure assessment risk quotient (RQ) values of thiamethoxam in Chinese kale for different Chinese consumers were 0.08-0.19% and 0.05-0.12%, respectively, and those of clothianidin were 0.01-0.04% and 0.02-0.04%, respectively, all of the RQ values were lower than 100%. CONCLUSION: Thiamethoxam in Chinese kale was rapidly degraded following first-order kinetics models. The dietary risk of thiamethoxam and clothianidin through Chinese kale was negligible to consumers. The results from this study are important reference for Chinese governments to developing criteria for the safe and rational use of thiamethoxam, setting maximum residue levels (MRLs), monitoring the quality safety of agricultural products and protecting consumer health. © 2021 Society of Chemical Industry.