Activation of endodontic irrigants using a 9.3 µm CO2 and diode lasers: A laboratory proof of concept model.

PURPOSE: To investigate the differences between irrigant propagation and temperature changes using laser-activated irrigation (LAI) at different settings in an artificial root canal model. METHODS: Using an artificial resin root canal model, irrigant activation was achieved in 19 experimental groups with eight samples each. A 9,300 nm CO2 laser, two diode lasers with different settings (wavelengths 455, 808, 970, and 980 nm) were compared to 2,940 nm Er:YAG laser and traditional needle irrigation. Er:YAG and CO2 laser were activated in the pulpal chamber only, while diode lasers and needles were inserted into the main root canal. Lasers were activated for 5x 20 seconds resulting in 100 seconds of activation or rinsing for each sample. After each activation of 20 seconds, a photo was taken of the side canals and the propagation of the dye was measured with a digital measuring tool after calibration. Further, the temperature of the irrigant was reported after activation of 20 seconds and repeated 5 times. Data were checked for normality and statistically compared. RESULTS: All lasers increased the irrigant propagation compared to conventional irrigation. Significant differences were found between groups regarding propagation and temperature (P< 0.0027). Er:YAG and CO2 laser had similar effects on irrigant propagation in middle and apical located side-canals with specific power parameters and were superior to diode lasers and syringe irrigation. The irrigant's temperature increased significantly with the diode and CO2 lasers. CLINICAL SIGNIFICANCE: Diode lasers and CO2 lasers have not been established for irrigant activation. 9,300 nm CO2 lasers absorb well in water and were shown to introduce vapor bubble formation and streaming in water. Diode lasers are highly accepted in periodontics. The laser light is not absorbed in water but interacts with bacteria as well as soft tissues and contributes therefore to infection control. With a modified laser tip it was however possible to introduce cavitation and streaming in irrigants.

Monitoring silver diamine fluoride application with optical coherence tomography and thermal imaging: An in vitro proof of concept study.

OBJECTIVES: The purpose of this study was to show that optical coherence tomography (OCT) and thermal imaging can be used to monitor changes in the structure and activity of caries lesions over time after treatment with silver diamine fluoride (SDF). METHODS: Artificial caries lesions were formed on enamel and dentin bovine blocks. Each block was partitioned into five windows with the central three windows exposed to a demineralization solution to create lesions: one sound window served as a sound control (SC), one sound window was exposed to SDF to serve as a test control (SCT), one lesion window served as a lesion control (LC), one lesion window received one application of SDF (L1), while the other lesion window received two applications of SDF (L2). Each window was scanned using OCT before SDF application, and every week subsequently, for 12 weeks after initial SDF treatment. Changes in the mean intensity and the width of the peak of increased reflectivity due to the lesion and SDF along with the intensity at a depth of 180 µm from the surface representing optical penetration through the lesion were monitored. Changes in the heat lost, ΔQ (temperature integrated over time) of each window during drying with air were also monitored using a thermal imaging camera. Transverse microradiography (TMR), and high-resolution microscopy were also used for the analysis of selected samples. RESULTS: The reflectivity and optical penetration of sound and lesion areas of enamel and dentin manifested significant changes in OCT images after SDF application. Thermal imaging showed significant differences in ΔQ indicative of permeability changes in the sound and lesion areas of enamel and dentin after SDF application.

Prevalence of Molar Incisor Hypomineralization in over 30,000 Schoolchildren in Switzerland.

OBJECTIVES: To quantify the prevalence of Molar Incisor Hypomineralization (MIH) in the canton of Geneva, Switzerland. STUDY DESIGN: Thirty-eight dentists of the state school dental services were trained to detect and classify MIH cases. All children (32,142) from age 4 to 12 were examined during the annual dental screening offered by the state. Cases were scored as mild, moderate or severe. RESULTS: The prevalence of hypomineralizations was found to be 7.45% when all hypomineralized teeth were taken into consideration. MIH cases were found to be at 6.6%. Out of the MIH cases, 51% scored as mild, 36% as moderate and 13% as severe. CONCLUSION: The mean prevalence of MIH in Geneva school children was found to be 6.6%. This seems to be lower than the European and the global average. However, with almost half cases being moderate or severe, asserting a proper management protocol is necessary.

High Contrast Reflectance Imaging of Enamel Demineralization and Remineralization at 1950-nm for the Assessment of Lesion Activity.

BACKGROUND AND OBJECTIVES: Previous studies have shown that large changes in the diffuse reflectivity of caries lesions during drying with air can be used to assess lesion activity. The largest changes occur at short wavelength infrared (SWIR) wavelengths coincident with high water absorption. The strongest water absorption in the SWIR occurs at 1950 nm. In this study changes in the reflectivity of simulated lesions with varying degrees of remineralization was measured at 1500-2340 nm and at 1950 nm as the samples were dried with air. STUDY DESIGN/MATERIALS AND METHODS: Twenty bovine enamel surfaces each with five treatment windows were exposed to two demineralization/remineralization regimens to produce simulated lesions of varying depth, severity, and mineral gradients. An extended range tungsten-halogen lamp with a long pass filter (1500-2340 nm) and a broadband amplified spontaneous emission source centered near the peak of the water-absorption band at 1950-nm were used as light sources and an extended range InGaAs camera (1000-2340 nm) was used to acquire reflected light images as the samples were dried with air. Lesions were also assessed using digital microscopy, polarized light microscopy, optical coherence tomography, and transverse microradiography. RESULTS: Both wavelength ranges showed extremely high lesion contrast (>0.9) for all six lesion treatment windows in both models. The change in contrast (ΔI) was significantly higher for the 1950 nm broadband source for all the intact lesion windows compared with the 1500-2340 nm wavelength range. CONCLUSION: SWIR light at 1950 nm yields extremely high contrast of demineralization and appears to be the optimum wavelength for the assessment of lesion activity on tooth coronal surfaces. Lasers Surg. Med. 00:00-00, 2020. © 2020 Wiley Periodicals LLC.

Staining susceptibility of resin composite materials.

PURPOSE: To evaluate the color stability of three resin-based materials continuously exposed to various staining agents. METHODS: 144 disc-shaped specimens were made of each of the three tested composites (Essentia, Brillant, Inspiro). Half of them were 1 mm thick, the other half 1.2 mm thick. The thicker group was then polished up to 4,000 grit and reduced to 1 mm thickness, also. All specimens, after 24-hour dry storage in an incubator, received an initial color measurement by means of a calibrated reflectance spectrophotometer (SpectroShade). Specimens were then divided into six groups (n=6) and immersed in five staining solutions or artificial saliva (control). All specimens were kept in an incubator at 37°C for 28 days. Staining solutions (red wine, curry mixed in water, curry mixed in oil, tea and coffee) were changed every 7th day to avoid bacteria or yeast contamination. After 28 days of storage, spectrophotometric measurements were repeated and L*a*b* scores once more recorded to determine the color (ΔE00) changes. RESULTS: All tested materials showed significant color changes after 28 days staining immersion. ΔE00 of polished samples varied from 1.1 (Essentia/distilled water measured over a white background as well as Essentia, Inspiro/distilled water measured over a black background) to 32.5 (Inspiro/wine measured over a white background). CLINICAL SIGNIFICANCE: Staining of restorative materials seems to be dependent on the composition of the product itself. Unpolished samples were more prone to staining than the polished ones.

Non-invasive proximal adhesive restoration of natural non-cavitated proximal lesions.

PURPOSE: To investigate the infiltration potential of different self-etch adhesives into natural non-cavitated proximal lesions and the effect of dehydration protocol on the infiltration of a self-etch adhesive. METHODS: 29 extracted molars and premolars with natural proximal lesions (ICDAS 1-2) were sectioned through the lesion providing two samples from each lesion. To compare the different adhesives, three groups of eight lesions were abraded with fine metallic strips and then etched with 37% H3PO4 acid for 120 seconds. All teeth were stained with rhodamine isothiocyanate. After drying with compressed air and ethanol application, lesions were infiltrated with Scotchbond Universal, Clearfil SE Protect or OneCoat 7 Universal for 180 seconds and then coated with a thin layer of flowable composite (Tetric Flow). To compare the effect of dehydration protocol on infiltration, two groups of nine paired lesions were pretreated as described above. One group was dried using compressed air alone and the second group was dried using compressed air and ethanol, both groups were then infiltrated with Scotchbond Universal then coated with a thin film of flowable composite. After light curing, un-encapsulated dye was bleached by immersion in hydrogen peroxide. Remaining lesion pores were stained with sodium fluorescein solution. Thin cuts of the teeth were observed with confocal microscopy and computer image analysis was performed (ImageJ). RESULTS: ANOVA and Duncan post-hoc tests showed no significant differences of the infiltrated area between the three adhesives (P= 0.835), no significant difference was found between the group dried with air compared to the one dried with air and ethanol. It can be concluded that the tested adhesives may be used for infiltration of natural lesions following the described pretreatment. CLINICAL SIGNIFICANCE: Enamel pretreatment with metallic strip and 37% H3PO4 acid promotes the infiltration of different adhesives into natural non-cavitated caries lesions.

Non-invasive proximal adhesive restoration (NIPAR) compared to resin infiltration for treating initial proximal carious lesions.

PURPOSE: To compare a new technique of non-invasive proximal adhesive restoration (NIPAR) to the infiltration concept technique (ICON). METHODS: Extracted human posterior teeth with non-cavitated proximal carious lesions (ICDAS code 1-2) were cut vertically to obtain two symmetrical lesions. Group 1 (NIPAR):Half of the paired lesions surfaces (n=13) were abraded with metallic strips and etched with 37% H3PO4 for 120 seconds. Group 2 (ICON):The other half of the paired lesions' surfaces (n=13) were etched with 15% HCl gel for 120 seconds. All samples were then stained with rhodamine isothiocyanate (RITC). After ethanol drying and isolation of the cut surface, Group 1 samples were infiltrated with Scotchbond Universal for 180 seconds and coated with a thin film of Tetric flow. Group 2 samples were infiltrated with ICON infiltrant following manufacturer's instructions. After light curing, unbound rhodamine was bleached by immersion in 30% hydrogen peroxide for 12 hours. Remaining lesion pores were stained with sodium fluorescein solution. Samples were observed with confocal microscopy (CLSM) and the percentage of infiltration (area of resin infiltration/area of total demineralization ×100) was calculated using ImageJ. RESULTS: 11 samples out of 13 showed larger infiltrated area of the lesions in Group 1 (NIPAR) compared to Group 2 (ICON). Statistical analysis revealed a significant difference between the two groups (P< 0.05). Within the limitations of this study, NIPAR allowed for better infiltration of non-cavitated proximal carious lesions when compared to ICON. CLINICAL SIGNIFICANCE: The combination of infiltration and sealing using non-invasive proximal adhesive restoration (NIPAR) offers a suitable non-invasive treatment option for non-cavitated proximal lesions combining the advantages of sealing and infiltration.

Comparing different enamel pretreatment options for resin-infiltration of natural non-cavitated carious lesions.

PURPOSE: To compare two different enamel pretreatments and their effect on the efficiency of penetration of a one-component adhesive into natural carious lesions. METHODS: Eight extracted human molars and premolars with non-cavitated interproximal lesions were selected. ICDAS code 1-2 was assessed by visual, microscopic, X-ray and Diagnocam record analysis. Samples were cut vertically across the demineralization to obtain two symmetrical lesions, (n=16). After isolating the cut surfaces with nail varnish, paired lesion halves' surfaces were pretreated with two different techniques: Group 1: surfaces were firstly abraded with fine diamond-coated metallic strips (Steelcarbo) and then etched with 37% H3PO4 acid (Omni-etch, 120 seconds); Group 2: lesion surfaces were etched with 15% HCl acid (Icon-etch, 120 seconds). All teeth were stained with rhodamine isothiocyanate (RITC) solution (12 hours) and subsequently stored in dry chamber (3 hours). All samples were penetrated with a one-component adhesive (Scotchbond Universal) for 180 seconds and coated with a thin layer of flowable composite (Tetric Flow). After light curing, un- encapsulated dye was bleached by immersion in 30% hydogen peroxide for 12 hours at 37°C. Remaining lesion pores were stained with sodium fluorescein solution. Thin cuts of the teeth were observed with confocal microscopy and computer image analysis was performed (ImageJ). The percentage of penetration (area of resin penetration/area of total demineralization x100) was calculated. RESULTS: Pretreatment with fine aluminum oxide-coated metallic strip followed by 37% H3PO4 acid showed a larger infiltration area (51.7% ± 12.2) in almost all samples compared to pretreatment with 15% HCl acid alone (22.1% ± 13.2). Statistical analysis using t-test showed a significant difference between the two groups (P = 0.011).

An in-vitro study on effects of laser activation on dye penetration in human root dentin.

Objective: To evaluate the penetration of a dye in root dentin after activation with different laser wavelengths. Materials: Palatal roots of 38 human molars were enlarged and disinfected. Irrigation activation was performed with an Er:YAG laser: @50 mJ, 15 Hz (Er:YAG); a 9.3 µm CO2 laser: @40% power (CO2); diode lasers 455 nm/970 nm: @0.8 W, 15 Hz (D455, D970) and 808/980 nm: @1 W (D808, D980) and compared to positive control: etching with 35% H3PO4 (POS); negative control: water (NEG) and conventional needle irrigation: NaOCl and ethylenediaminetetraacetic acid (EDTA) (CONV). Methylene blue solution was introduced in the canal and laser-activated or left untouched for 100 s before the roots were dried and cut into horizontal slices. Dye penetration was automatically calculated by color recognition of two samples per root third (n = 8 per group in each coronal, middle and apical root thirds). The presence and absence of a smear layer was checked in two additional samples of the negative and positive control under scanning electron microscopy (SEM). Results: Full-depth infiltration was not achieved in any group. Dye penetration in CONV was significantly less than in Er:YAG, CO2, POS, D455, D970, D808 and similar to NEG and D980 when results of different root thirds were pooled. Conclusion: Laser activation using certain parameters enhanced dye penetration compared to conventional needle irrigation with NaOCl and EDTA (CONV).

An in vitro study on the influence of laser-activated irrigation on infiltration and leakage of a dual curing-resin cement as an endodontic sealer.

Objectives: The study aims to investigate the effects of laser-activated irrigation on infiltration and microleakage of a dual-curing resin cement applied as a root canal sealer. Methods: Thirty-eight extracted upper molars were attributed to four experimental groups. Roots were mechanically enlarged and disinfected (NaOCl). Control samples (n = 11) were irrigated with conventional needles and three different lasers were used to activate the irrigant in the other groups (n = 9): 2.94 µm Er:YAG laser, 9,300 µm CO2 laser and 808 nm diode laser with a modified black coated laser tip. Final irrigation was performed in each group with ethylenediaminetetraacetic acid (EDTA), sodium hypochlorite (NaOCl) and sodium chloride (NaCl) activated with lasers and in the control without activation.Dentin tubules were then labeled with a red fluorophore (Rhodamine B) and the root canals were sealed with a dual-curing resin cement (Paracore). The cement fixed the dye on the sealed and infiltrated dentin parts. To remove the Rhodamine not fixed by the cement, roots were then sectioned horizontally and immersed in hydrogen peroxide (H2O2). The empty dentin tubules spaces were then labeled with a green fluorophore (Fluorescein) allowing the visualization of infiltration and microleakage by confocal microscopy. Results: Percentages of infiltration were significantly higher in the middle root third of the control and Er:YAG laser-activated samples compared to CO2 or diode laser groups. Microleakage was present in all experimental groups but significantly less after CO2 laser activation. Conclusion: Laser-activated irrigation impacted resin cement infiltration and microleakage dependent on the applied wavelength. Er:YAG laser activation led to higher values of infiltration and microleakage compared to CO2 and diode lasers.

Atlas of Dental Near-Infrared Transillumination Images.

Technological improvements have introduced significant innovations in dentistry and broadened the array of tools and techniques in dental care. One technological development that has been widely researched over the past 20 years is the use of Near-Infrared Transillumination (NIRT) imaging for the diagnosis of dental caries. This paper aims to introduce a comprehensive collection of NIRT images, intended as a reference tool for routine dental examinations, dental research, pedagogical activities, and forensic odontology. The collection presents pairwise clinical and NIRT images categorized as follows: (a) healthy teeth, (b) carious teeth, (c) restored teeth, (d) enamel defects, and (e) diverse findings. This atlas could be a valuable tool for the dental community as it is designed as an identification guide of NIRT illustrated dental features.

Detection, Diagnosis, and Monitoring of Early Caries: The Future of Individualized Dental Care.

Dental caries remains a significant global health issue. It was highlighted by the World Health Organization's 2022 reports that despite the efforts and scientific advancements in caries detection and management, the situation has only marginally improved over the past three decades. The persistence of this problem may be linked to outdated concepts developed almost a century ago but are still guiding dentists' approach to caries management today. There is a need to reconsider professional strategies for preventing and managing the disease. Contemporary dentistry could benefit from embracing new concepts and technologies for caries detection and management. Dentists should explore, among others, alternative methods for caries detection such as optical-based caries detection. These tools have been established for over a decade and they align with current disease understanding and international recommendations, emphasizing early detection and minimally invasive management. This narrative review presents the current state of knowledge and recent trends in caries detection, diagnosis, monitoring, and management, offering insights into future perspectives for clinical applications and research topics.

Evaluating the use of self-conditioning adhesive combined with dual curing resin cement as an endodontic sealer: An in vitro study.

Objectives: To compare infiltration, sealing and microleakage in root dentin with a self-conditioning adhesive system combined with dual curing resin (resin-based cement) to a conventional epoxy-resin-based sealer using confocal microscopy imaging. Methods: 26 roots were enlarged and disinfected. Dentin tubules of 24 teeth were labelled with a red fluorophore (Rhodamine B) (two samples served as controls). Root canal samples were sealed in group AH (n = 11) with a conventional sealer (AH Plus Root Canal Sealer, Dentsply DeTrey) and in group RC (n = 11) with a resin-based cement (Parabond combined with Paracore, Coltène). Roots were then sectioned horizontally and immersed in H2O2 to remove the Rhodamine B not fixed by the sealers. The empty dentin spaces were labeled with a green fluorophore (Fluorescein) enabling the evaluation of infiltration as well as microleakage by confocal microscopy. Two additional samples were fractured in vertical direction for observation under SEM. Results: Group RC presented significantly more infiltration in the middle third than in the middle and apical thirds of group AH. Microleakage was significantly higher in group AH than in group RC. SEM images revealed more dentin plugs and a homogenous resin layer in group RC in contrast to group AH. Conclusion: The resin-based cement revealed promising outcomes compared to a traditional epoxy resin based sealer.

Infiltration and microleakage in infiltrated and sealed root dentin samples are higher in middle than apical root thirds. Root dentin infiltration and sealing with a self-conditioning adhesive system and a dual-curing resin cement revealed less microleakage than with an epoxy-resin-based sealer.

Novel hybrid-glass-based material for infiltration of early caries lesions.

OBJECTIVES: To assess the effectiveness of two experimental, hybrid-glass-based infiltrants in arresting artificial white spot lesions (WSLs) in vitro, and to compare it with resin-based infiltrant Icon. METHODS: Artificial WSLs were formed on bovine enamel specimens (n = 68). Specimens were divided into four groups according to WSLs treatment: 1) no-treatment control (NTC), 2) infiltration with Icon (Icon), 3) infiltration with experimental hybrid-glass material (EXP), and 4) infiltration with experimental hybrid-glass material containing hydroxyapatite (HAp) nanoparticles (1%) (EXP-HAp). Half of the specimens from each group were subjected to cariogenic challenge using pH-cycling, consisting of a 7-day alternate incubation (37°C) in demineralization (4 h/day, pH=4.6) and remineralization solutions (20 h/day, pH=7.2). Another half of the specimens was incubated in distilled water (control). Caries progression was assessed by measuring surface micro-hardness (SMH), roughness (Ra) and average surface level, and by analyzing WSLs morphology. Non-cycled and pH-cycled specimens were compared with Man-Whitney U test, while different treatment groups were compared with Kruskal-Wallis test with pairwise comparisons (p < 0.05). RESULTS: In all groups (NTC, Icon and EXP-HAp) except EXP, SMH decreased significantly after pH cycling. In addition, SMH increased in EXP upon pH cycling and was significantly higher than in other pH-cycled groups (<0.001). Ra increased considerably, while surface level decreased after pH cycling in all groups except in EXP. Signs of demineralization and roughness increase in NTC, Icon and EXP-HAp were also observed with the SEM. SIGNIFICANCE: Experimental hybrid-glass-based material without HAp-nanoparticles could completely arrest the progression of WSLs, unlike its version with HAp-nanoparticles and resin-based infiltrant Icon.

Cytotoxicity and anti-biofilm properties of novel hybrid-glass-based caries infiltrant.

OBJECTIVES: To assess the cytotoxicity of an experimental hybrid-glass-based infiltrant and its effect on biofilm attachment, growth and metabolic activity, and to compare it to the resin-based infiltrant Icon. METHODS: Cytotoxicity of hybrid-glass-based material (EXP) and resin-based infiltrant Icon (Icon) was tested in direct contact tests on freshly cured (direct_mat) and on materials kept for 24 h in cell culture medium (direct_exmat), and extract test with materials 24-h extracts (extract). Cell viability of L929 mouse fibroblast cell line was measured with MTT assay, according to ISO10993-5:2009. Biofilm attachment (5 h), growth (24 h and 48 h) and lactic-acid production (24 h and 48 h) on glass-disk specimens coated with EXP or Icon, or uncoated (control), were assessed using a microcosm biofilm model and Amsterdam Active Attachment system. At indicated time points, biofilms were harvested, plated, and CFU counts were determined, while lactic-acid production was measured colorimetrically. RESULTS: Cell viability reduction by EXP was below 30%-threshold in direct contact tests, while in extract test an increased cell viability was observed. Icon reduced cell viability substantially in all three tests. Significantly less bacteria attached to the surface of EXP after 5 h compared to Icon and control. Biofilm growth was significantly lower on EXP than on Icon and control after 24 h, but this difference was smaller and statistically insignificant after 48 h. There was no difference in lactic-acid production among groups. SIGNIFICANCE: Novel hybrid-glass-based infiltrant seems to have a better biocompatibility and accumulates on its surface less bacteria than resin-based infiltrant, which makes it an attractive resin-free alternative.

High contrast reflectance imaging at 1950 nm for the assessment of lesion activity on extracted teeth.

Changes in the reflectivity of lesions on the proximal surfaces of extracted human teeth were measured at SWIR wavelengths from 1300-2000 nm as they were dried with air to assess lesion activity. An extended range tungsten-halogen lamp with bandpass filters of varying wavelength (bandwidth) 1300 nm (90), 1460 nm (85), 1535 nm (80), and 1675 nm (90) along with a broadband ASE source centered near the peak of the water-absorption band at 1950-nm were used as light sources and an extended range InGaAs camera (1000-2340 nm) was used to acquire reflected light images as the samples were dried with air. MicroCT images were used as a gold standard for comparison. SWIR light at 1950 nm yields extremely high contrast of demineralization and appears to be the optimum wavelength for the assessment of lesion activity on tooth coronal surfaces.

Dynamic SWIR imaging near the 1950-nm water absorption band for caries lesion diagnosis.

SIGNIFICANCE: It is not sufficient to detect caries lesions on tooth surfaces; it is also necessary to measure the activity of the lesions to determine if intervention is needed. Changes in the reflectivity of lesion areas during dehydration with forced air at short wavelength infrared (SWIR) wavelengths can be used to assess lesion activity since these changes represent the evaporation dynamics of water from the lesion. AIM: The aim of this study is to develop new optical methods for assessing lesion activity on tooth surfaces utilizing the strong water absorption band near 1950-nm. APPROACH: The time-resolved reflectivity of 20 active and arrested caries lesions on the surfaces of human extracted teeth was monitored at 1300 to 2000 nm using broadband light sources and an extended range InGaAs camera during drying with air. RESULTS: Multiple parameters representing the rate of change of the lesion reflectivity correlated with the presence of a highly mineralized outer surface zone indicative of lesion arrest measured with x-ray microtomography (microCT). Performance at 1950-nm was higher than for other wavelengths. CONCLUSIONS: This study demonstrates that SWIR imaging near 1950-nm has great potential for the assessment of lesion activity.

Dual short wavelength infrared transillumination/reflectance mode imaging for caries detection.

SIGNIFICANCE: We have developed a clinical probe capable of acquiring near-simultaneous short-wavelength infrared (SWIR) reflectance and occlusal transillumination images of lesions on tooth proximal and occlusal surfaces. We hypothesize that dual images will aid in differentiating between shallow and deep occlusal lesions and reduce the potential of false positives (FPs). AIM: The aim of this study was to test the performance of the dual reflectance and occlusal transillumination probe on extracted teeth prior to commencing clinical studies. APPROACH: The dual probe was 3D printed and the imaging system uses an InGaAs camera and broadband superluminescent diode light sources that emit broadband light at 1300 nm for occlusal transillumination and 1600-nm light for cross-polarization reflectance. The diagnostic performance of the dual probe was assessed using 120 extracted teeth with approximal and occlusal lesions. Reflectance and transillumination images were fused into single images to enhance the contrast between sound and lesion areas. The lesion contrast in both modes did not increase significantly with either the lesion depth or the distance from the occlusal surface for approximal lesions. In addition, the diagnostic performance of radiography, the individual reflectance and transillumination images, dual images, and fused images were compared using micro-computed tomography as the gold standard. RESULTS: Reflectance imaging at 1600 nm yielded the highest diagnostic accuracy for lesions on both occlusal and proximal surfaces while radiography yielded the lowest number of FPs. CONCLUSION: This study demonstrates that simultaneous acquisition of both reflectance and transillumination SWIR images is possible with a single clinical device.

Optical Coherence Tomography (OCT) for the evaluation of internal adaptation of class V resin restorations on Dentin.

Internal adaptation of adhesive restorations affects their longevity. In a clinical setting, the dentists use visual and tactile examination to evaluate marginal adaptation, while radiographs provide somewhat reliable information about adaptation or secondary caries present. For class V restorations located on the vestibular (buccal) surfaces, none of the tools available can provide any information about the internal adaptation or the presence of secondary caries. OCT has been proven to be a useful tool for non-destructive assessment of internal adaptation of adhesive restorations. This paper is evaluating the use of a new high-resolution handheld OCT prototype with a pen-shaped intraoral tip and an imaging depth of 8mm to examine the internal adaptation and the presence of demineralization under resin restorations on the vestibular dentin surface. The Axsun OCT system helped evaluate the internal adaptation of composite restorations, differentiate between healthy and demineralised dentin, adhesive, and restoration layers. OCT provided a unique visualization and characterization of internal structures as well as non-contact assessment of marginal adaptation.

Efficacy of P11-4 for the treatment of initial buccal caries: a randomized clinical trial.

To investigate the safety and efficacy of Self-Assembling Peptide P11-4 (SAP P11-4) compared to placebo or fluoride varnish (FV), a randomized, controlled, blinded, split-mouth study with sequential design was conducted. Subjects presenting two teeth with White-Spot-Lesions (WSLs) were included and teeth were randomly assigned to test or control. Control received placebo at baseline (D0) and test SAP P11-4, all received FV at Day 90 (D90). Standardized photographs were taken at each visit, and WSL size changes were morphometrically assessed. Hierarchical Linear Modelling, considering paired and sequential design, was used to test four hypotheses. SAP P11-4 lesions (test, D90-D0) showed significant WSL size reduction compared to placebo (control, D90-D0; p = 0.008) or FV (control, D180-D90; p = 0.001). Combination of SAP P11-4 and delayed FV after 90 days (test, D180-D0), showed a significant difference compared to FV alone (control D270-D90; p = 0.003). No significant difference on FV efficacy was found when SAP P11-4 was applied 3 months before FV (test D270-D90; control D270-D90, p = 0.70). SAP P11-4 treatment resulted in superior caries regression compared to either placebo or FV, and FV efficacy seems not to be affected by SAP P11-4. SAP P11-4 was found to be a safe and effective WSL treatment.