Influence of PLGA End Groups on the Release Profile of Dexamethasone from Ocular Implants.

The present study deals with the development of dexamethasone (DM)-loaded implants using ester end-capped Resomer RG 502 poly(lactic acid-co-glycolic acid) (PLGA) (502), acid end-capped Resomer RG 502H PLGA (502H), and a 502H:502 mixture (3:1) via hot melt extrusion (HME). The prepared intravitreal implants (20 and 40% DM loaded in each PLGA) were thoroughly investigated to determine the effect of different end-capped PLGA and drug loading on the long-term release profile of DM. The implants were characterized for solid-state active pharmaceutical ingredient (APIs) using DSC and SWAXS, water uptake during stability study, the crystal size of API in the implant matrix using hot-stage polarized light microscopy, and in vitro release profile. The kinetics of PLGA release was thoroughly investigated using quantitative 1H NMR spectroscopy. The polymorph of DM crystal was found to remain unchanged after the extrusion and stability study. However, around 3 times reduction in API particle size was observed after the HME process. The morphology and content uniformity of the RT-stored samples were found to be comparable to the initial implant samples. Interestingly, the samples (mainly 502H) stored at 40 °C and 75% RH for 30 d demonstrated marked deformation and a change in content uniformity. The rate of DM release was higher in the case of 502H samples with a higher drug loading (40% w/w). Furthermore, a simple digital in vitro DM release profile derived for the formulation containing a 3:1 ratio of 502H and 502 was comparable with the experimental release profile of the respective polymer mixture formulation. The temporal development of pores and/or voids in the course of drug dissolution, evaluated using µCT, was found to be a precursor for the PLGA release. Overall, the release profile of DM was found to be dependent on the PLGA type (independent of subtle changes in the formulation mass and diameter). However, the extent of release was found to be dependent on DM loading. Thus, the present investigation led to a thorough understanding of the physicochemical properties of different end-capped PLGAs and the underlying formulation microstructure on the release profile of a crystalline water-insoluble drug, DM, from the PLGA-based implant.

Dental and Maxillofacial Cone Beam CT-High Number of Incidental Findings and Their Impact on Follow-Up and Therapy Management.

Cone beam computed tomography (CBCT) is increasingly used for dental and maxillofacial imaging. The occurrence of incidental findings has been reported, but clinical implications of these findings remain unclear. The study's aim was to identify the frequency and clinical impact of incidental findings in CBCT. A total of 374 consecutive CBCT examinations of a 3 year period were retrospectively evaluated for the presence, kind, and clinical relevance of incidental findings. In a subgroup of 54 patients, therapeutic consequences of CBCT incidental findings were queried from the referring physicians. A total of 974 incidental findings were detected, involving 78.6% of all CBCT, hence 2.6 incidental findings per CBCT. Of these, 38.6% were classified to require treatment, with an additional 25.2% requiring follow-up. Incidental findings included dental pathologies in 55.3%, pathologies of the paranasal sinuses and airways in 29.2%, osseous pathologies in 14.9% of all CBCT, and findings in the soft tissue or TMJ in few cases. Clinically relevant dental incidental findings were detected significantly more frequently in CBCT for implant planning compared to other indications (60.7% vs. 43.2%, p < 0.01), and in CBCT with an FOV ≥ 100 mm compared to an FOV < 100 mm (54.7% vs. 40.0%, p < 0.01). Similar results were obtained for paranasal incidental findings. In a subgroup analysis, 29 of 54 patients showed incidental findings which were previously unknown, and the findings changed therapeutical management in 19 patients (35%). The results of our study highlighted the importance of a meticulous analysis of the entire FOV of CBCT for incidental findings, which showed clinical relevance in more than one in three patients. Due to a high number of clinically relevant incidental findings especially in CBCT for implant planning, an FOV of 100 × 100 mm covering both the mandible and the maxilla was concluded to be recommendable for this indication.

The effect of a combination of 0.1% octenidine dihydrochloride and 2% 2-phenoxyethanol (octenisept) on wound healing in pigs in vivo and its in vitro percutaneous permeation through intact and barrier disrupted porcine skin.

A combination of 0.1% octenidine dihydrochloride and 2% 2-phenoxyethanol (octenisept) is a commonly used disinfectant in human medicine. As porcine skin represents an adequate model for human skin, the effect of octenidine dihydrochloride and phenoxyethanol on wound healing is studied in pigs. Furthermore, the in vitro percutaneous permeation of the test substances is studied. The impact of the test formulations on wound healing is examined (A) under non occlusive conditions and (B) in comparison to another disinfectant based on povidone-iodine under occlusive conditions, while wounds are treated daily with the test substances. The percutaneous permeation of octenidine dihydrochloride and phenoxyethanol is studied in Franz-type diffusion cells with intact skin as well as barrier disrupted after tape stripping. Compared with povidone-iodine or vehicle treatment as well as untreated control wounds the treatment of wounds with the test formulation has no influence on the healing rate in pigs and does not induce retardation of wound healing. The in vitro diffusion experiment reveals that octenidine dihydrochloride is only detectable in the acceptor chamber of three-barrier disrupted skin samples. Phenoxyethanol permeates through intact porcine skin in amounts of 11.3% and through barrier disrupted skin in amounts of 43.9%

Prediction of solid fraction from powder mixtures based on single component compression analysis.

The aim of this study was to provide a systematic evaluation of various compression models (Percolation, Kawakita, Exponential model) in respect to predict tablet́s solid fraction for direct compression mixtures, based on single component compression analysis. Four mixtures were compressed over a wide pressure range at various fractions of microcrystalline cellulose (MCC) and pre-agglomerated lactose monohydrate (LAC) to compare an adjusted Percolation, Kawakita and a simple Exponential model. Based on single compression analysis of the pure excipients and application of these models, it was possible to predict the solid fraction of all mixtures. The Kawakita model showed overall superior prediction accuracy, whereas the Percolation model resulted in the best fit for mixtures containing microcrystalline cellulose in a range of 72%-48%. Both models were in good agreement at residuals below 3%.

A fast and flexible PEG-mediated transient expression system in plants for high level expression of secreted recombinant proteins.

Plant expression systems offer a valuable alternative to traditional systems for the production of recombinant biopharmaceuticals. A highly efficient polyethyleneglycol (PEG)-mediated transient expression system for secreted recombinant proteins in plants has been developed. The human vascular endothelial growth factor 121 (rhVEGF) has been successfully expressed and efficiently secreted into the culture medium by transiently transformed moss protoplasts. In order to obtain secretion efficiency data, different expressed signal peptides were analysed and time course studies were performed with expression constructs containing different promoters. The transformation procedure was optimised for high level expression (up to 10 microg/ml) and successfully performed even with a transgenic glyco-engineered strain lacking plant-specific immunogenic sugar residues in N-glycans. The amount of rhVEGF was produced in such quantity that it allowed for the analysis of biological activity, silver-staining and Western blotting, revealing the correct formation and processing of the homodimer. This fast and flexible transient expression system enables feasibility studies and construct optimisation to be concluded within a few days, thus avoiding the time consuming step of having to generate stably transformed lines.