Composite Polycaprolactone/Gelatin Nanofiber Membrane Scaffolds for Mesothelial Cell Culture and Delivery in Mesothelium Repair.

To repair damaged mesothelium tissue, which lines internal organs and cavities, a tissue engineering approach with mesothelial cells seeded to a functional nanostructured scaffold is a promising approach. Therefore, this study explored the uses of electrospun nanofiber membrane scaffolds (NMSs) as scaffolds for mesothelial cell culture and transplantation. We fabricated a composite NMS through electrospinning by blending polycaprolactone (PCL) with gelatin. The addition of gelatin enhanced the membrane's hydrophilicity while maintaining its mechanical strength and promoted cell attachment. The in vitro study demonstrated enhanced adhesion of mesothelial cells to the scaffold with improved morphology and increased phenotypic expression of key marker proteins calretinin and E-cadherin in PCL/gelatin compared to pure PCL NMSs. In vivo studies in rats revealed that only cell-seeded PCL/gelatin NMS constructs fostered mesothelial healing. Implantation of these constructs leads to the regeneration of new mesothelium tissue. The neo-mesothelium is similar to native mesothelium from hematoxylin and eosin (H&E) and immunohistochemical staining. Taken together, the PCL/gelatin NMSs can be a promising scaffold for mesothelial cell attachment, proliferation, and differentiation, and the cell/scaffold construct can be used in therapeutic applications to reconstruct a mesothelium layer.

Polycaprolactone/Chitosan Composite Nanofiber Membrane as a Preferred Scaffold for the Culture of Mesothelial Cells and the Repair of Damaged Mesothelium.

Mesothelial cells are specific epithelial cells lining the serosal cavity and internal organs. Nonetheless, few studies have explored the possibility to culture mesothelial cells in a nanostructure scaffold for tissue engineering applications. Therefore, this study aims to fabricate nanofibers from a polycaprolactone (PCL) and PCL/chitosan (CS) blend by electrospinning, and to elucidate the effect of CS on the cellular response of mesothelial cells. The results demonstrate that a PCL and PCL/CS nanofiber membrane scaffold could be prepared with a comparable fiber diameter (~300 nm) and porosity for cell culture. Blending CS with PCL influenced the mechanical properties of the scaffold due to interference of PCL crystallinity in the nanofibers. However, CS substantially improves scaffold hydrophilicity and results in a ~6-times-higher cell attachment rate in PCL/CS. The mesothelial cells maintain high viability in both nanofiber membranes, but PCL/CS provides better maintenance of cobblestone-like mesothelial morphology. From gene expression analysis and immunofluorescence staining, the incorporation of CS also results in the upregulated expression of mesothelial marker genes and the enhanced production of key mesothelial maker proteins, endorsing PCL/CS to better maintain the mesothelial phenotype. The PCL/CS scaffold was therefore chosen for the in vivo studies, which involved transplanting a cell/scaffold construct containing allograft mesothelial cells for mesothelium reconstruction in rats. In the absence of mesothelial cells, the mesothelium wound covered with PCL/CS showed an inflammatory response. In contrast, a mesothelium layer similar to native mesothelium tissue could be obtained by implanting the cell/scaffold construct, based on hematoxylin and eosin (H&E) and immunohistochemical staining.

Simultaneous Fat Injection for Nasal Contouring in Orthognathic Patients.

BACKGROUND: Augmentation rhinoplasty with autologous fat grafting is a useful procedure to meet the demand for facial harmonization in the Asian population. We used this procedure during orthognathic surgery to address inadequate dorsum projection. This prospective study was conducted to determine the fat retention rate in patients undergoing simultaneous autologous fat injection augmentation rhinoplasty and orthognathic surgery. METHODS: Nineteen patients were treated with simultaneous bimaxillary orthognathic surgery and autologous fat grafting of the nasal dorsum and tip. The paired t test was used to compare the nasal volumes before and at least 6 months after surgery measured by 3-dimensional computer tomography scans. All measurements were performed twice by the same evaluator at least 2 weeks apart for intrarater consistency. RESULTS: Seventeen patients completed the study. The volume means before and after surgery were 22.3 ± 4.6 cm3 and 23.3 ± 4.7 cm3, respectively, with a mean difference of 1.0 ± 0.3 cm3 (P < .001). The mean retention rate was calculated to be 50.5% ± 7.0% (range: 40.5%-64.7%). Intrarater consistency was high with a Cronbach α of .97 (P < .001) and .98 (P < .001), respectively. CONCLUSION: This prospective study provides objective graft retention measurements for fat injection augmentation rhinoplasty combined with orthognathic surgery. All patients were satisfied with the results and no complications or additional morbidity was noted in the postoperative course. We consider this procedure to be a safe, reliable, and powerful adjunct to improve the aesthetic results of orthognathic surgery.

Simultaneous Orthognathic Surgery With Asian Double Eyelid Suture Blepharoplasty.

BACKGROUND: The main objective of contemporary orthognathic surgery is to correct dentofacial deformities. Nonetheless, many adjunct procedures to enhance the esthetic outcome in orthognathic surgical cases have been successfully incorporated to improve patient satisfaction. The authors report our preliminary experience of performing simultaneous orthognathic surgery with Asian double eyelid suture method blepharoplasty in the same surgical setting. METHOD: This case series report includes all 19 consecutive cases presenting to the Chang Gung Craniofacial Center for combined orthognathic surgery with Asian double eyelid suture method blepharoplasty. The double eyelid crease height was measured as the vertical line between the upper eyelid margin (eyelid lash) and the upper eyelid crease, observed at the mid-pupillary line with the eyes in primary gaze. RESULTS: There were no complications or relapse reported within this time period. There was significant improvement in the left and right mid-pupillary double eyelid crease height postsurgery. There were no statistically significant differences between the left and right mid-pupillary double eyelid crease heights after surgery indicating good eyelid crease height symmetry bilaterally was obtained. CONCLUSIONS: Orthognathic surgery combined with suture method blepharoplasty can be safely performed in the same surgical setting without inappropriate rise in costs or operating room time. This case series demonstrates that excellent esthetic results can be obtained in simultaneous bimaxillary orthognathic surgery with suture method Asian blepharoplasty.

Tension Stimulation of Tenocytes in Aligned Hyaluronic Acid/Platelet-Rich Plasma-Polycaprolactone Core-Sheath Nanofiber Membrane Scaffold for Tendon Tissue Engineering.

To recreate the in vivo niche for tendon tissue engineering in vitro, the characteristics of tendon tissue underlines the use of biochemical and biophysical cues during tenocyte culture. Herein, we prepare core-sheath nanofibers with polycaprolactone (PCL) sheath for mechanical support and hyaluronic acid (HA)/platelet-rich plasma (PRP) core for growth factor delivery. Three types of core-sheath nanofiber membrane scaffolds (CSNMS), consisting of random HA-PCL nanofibers (Random), random HA/PRP-PCL nanofibers (Random+) or aligned HA/PRP-PCL (Align+) nanofibers, were used to study response of rabbit tenocytes to biochemical (PRP) and biophysical (fiber alignment) stimulation. The core-sheath structures as well as other pertinent properties of CSNMS have been characterized, with Align+ showing the best mechanical properties. The unidirectional growth of tenocytes, as induced by aligned fiber topography, was confirmed from cell morphology and cytoskeleton expression. The combined effects of PRP and fiber alignment in Align+ CSNMS lead to enhanced cell proliferation rates, as well as upregulated gene expression and marker protein synthesis. Another biophysical cue on tenocytes was introduced by dynamic culture of tenocyte-seeded Align+ in a bioreactor with cyclic tension stimulation. Augmented by this biophysical beacon from mechanical loading, dynamic cell culture could shorten the time for tendon maturation in vitro, with improved cell proliferation rates and tenogenic phenotype maintenance, compared to static culture. Therefore, we successfully demonstrate how combined use of biochemical/topographical cues as well as mechanical stimulation could ameliorate cellular response of tenocytes in CSNMS, which can provide a functional in vitro environmental niche for tendon tissue engineering.

Functional Hyaluronic Acid-Polylactic Acid/Silver Nanoparticles Core-Sheath Nanofiber Membranes for Prevention of Post-Operative Tendon Adhesion.

In this study, we prepared core-sheath nanofiber membranes (CSNFMs) with silver nanoparticles (Ag NPs) embedding in the polylactic acid (PLA) nanofiber sheath and hyaluronic acid (HA) in the nanofiber core. The PLA/Ag NPs sheath provides mechanical support as well as anti-bacterial and anti-inflammatory properties. The controlled release of HA from the core could exert anti-adhesion effects to promote tendon sliding while reducing fibroblast attachment. From the microfibrous structural nature of CSNFMs, they function as barrier membranes to reduce fibroblast penetration without hampering nutrient transports to prevent post-operative peritendinous adhesion. As the anti-adhesion efficacy will depend on release rate of HA from the core as well as Ag NP from the sheath, we fabricated CSNFMs of comparable fiber diameter, but with thick (Tk) or thin (Tn) sheath. Similar CSNFMs with thick (Tk+) and thin (Tn+) sheath but with embedded Ag NPs in the sheath were also prepared. The physico-chemical properties of the barrier membranes were characterized in details, together with their biological response including cell penetration, cell attachment and proliferation, and cytotoxicity. Peritendinous anti-adhesion models in rabbits were used to test the efficacy of CSNFMs as anti-adhesion barriers, from gross observation, histology, and biomechanical tests. Overall, the CSNFM with thin-sheath and Ag NPs (Tn+) shows antibacterial activity with low cytotoxicity, prevents fibroblast penetration, and exerts the highest efficacy in reducing fibroblast attachment in vitro. From in vivo studies, the Tn+ membrane also shows significant improvement in preventing peritendinous adhesions as well as anti-inflammatory efficacy, compared with Tk and Tn CSNFMs and a commercial adhesion barrier film (SurgiWrap®) made from PLA.

Synthesis and characterization of PLGA/HAP scaffolds with DNA-functionalised calcium phosphate nanoparticles for bone tissue engineering.

Porous scaffolds of poly(lactide-co-glycolide) (PLGA; 85:15) and nano-hydroxyapatite (nHAP) were prepared by an emulsion-precipitation procedure from uniform PLGA-nHAP spheres (150-250 µm diameter). These spheres were then thermally sintered at 83 °C to porous scaffolds that can serve for bone tissue engineering or for bone substitution. The base materials PLGA and nHAP and the PLGA-nHAP scaffolds were extensively characterized by X-ray powder diffraction, infrared spectroscopy, thermogravimetry, differential scanning calorimetry, and scanning electron microscopy. The scaffold porosity was about 50 vol% as determined by relating mass and volume of the scaffolds, together with the computed density of the solid phase (PLGA-nHAP). The cultivation of HeLa cells demonstrated their high cytocompatibility. In combination with DNA-loaded calcium phosphate nanoparticles, they showed a good activity of gene transfection with enhanced green fluorescent protein (EGFP) as model protein. This is expected enhance bone growth around an implanted scaffold or inside a scaffold for tissue engineering.

Optimization of the Preparation of Magnetic Liposomes for the Combined Use of Magnetic Hyperthermia and Photothermia in Dual Magneto-Photothermal Cancer Therapy.

In this work, we aimed to develop liposomal nanocomposites containing citric-acid-coated iron oxide magnetic nanoparticles (CMNPs) for dual magneto-photothermal cancer therapy induced by alternating magnetic field (AMF) and near-infrared (NIR) lasers. Toward this end, CMNPs were encapsulated in cationic liposomes to form nano-sized magnetic liposomes (MLs) for simultaneous magnetic hyperthermia (MH) in the presence of AMF and photothermia (PT) induced by NIR laser exposure, which amplified the heating efficiency for dual-mode cancer cell killing and tumor therapy. Since the heating capability is directly related to the amount of entrapped CMNPs in MLs, while the liposome size is important to allow internalization by cancer cells, response surface methodology was utilized to optimize the preparation of MLs by simultaneously maximizing the encapsulation efficiency (EE) of CMNPs in MLs and minimizing the size of MLs. The experimental design was performed based on the central composite rotatable design. The accuracy of the model was verified from the validation experiments, providing a simple and effective method for fabricating the best MLs, with an EE of 87% and liposome size of 121 nm. The CMNPs and the optimized MLs were fully characterized from chemical and physical perspectives. In the presence of dual AMF and NIR laser treatment, a suspension of MLs demonstrated amplified heat generation from dual hyperthermia (MH)-photothermia (PT) in comparison with single MH or PT. In vitro cell culture experiments confirmed the efficient cellular uptake of the MLs from confocal laser scanning microscopy due to passive accumulation in human glioblastoma U87 cells originated from the cationic nature of MLs. The inducible thermal effects mediated by MLs after endocytosis also led to enhanced cytotoxicity and cumulative cell death of cancer cells in the presence of AMF-NIR lasers. This functional nanocomposite will be a potential candidate for bimodal MH-PT dual magneto-photothermal cancer therapy.

Preparation of Peptide and Recombinant Tissue Plasminogen Activator Conjugated Poly(Lactic-Co-Glycolic Acid) (PLGA) Magnetic Nanoparticles for Dual Targeted Thrombolytic Therapy.

Recombinant tissue plasminogen activator (rtPA) is the only thrombolytic agent that has been approved by the FDA for treatment of ischemic stroke. However, a high dose intravenous infusion is required to maintain effective drug concentration, owing to the short half-life of the thrombolytic drug, whereas a momentous limitation is the risk of bleeding. We envision a dual targeted strategy for rtPA delivery will be feasible to minimize the required dose of rtPA for treatment. For this purpose, rtPA and fibrin-avid peptide were co-immobilized to poly(lactic-co-glycolic acid) (PLGA) magnetic nanoparticles (PMNP) to prepare peptide/rtPA conjugated PMNPs (pPMNP-rtPA). During preparation, PMNP was first surface modified with avidin, which could interact with biotin. This is followed by binding PMNP-avidin with biotin-PEG-rtPA (or biotin-PEG-peptide), which was prepared beforehand by binding rtPA (or peptide) to biotin-PEG-maleimide while using click chemistry between maleimide and the single -SH group in rtPA (or peptide). The physicochemical property characterization indicated the successful preparation of the magnetic nanoparticles with full retention of rtPA fibrinolysis activity, while biological response studies underlined the high biocompatibility of all magnetic nanoparticles from cytotoxicity and hemolysis assays in vitro. The magnetic guidance and fibrin binding effects were also confirmed, which led to a higher thrombolysis rate in vitro using PMNP-rtPA or pPMNP-rtPA when compared to free rtPA after static or dynamic incubation with blood clots. Using pressure-dependent clot lysis model in a flow system, dual targeted pPMNP-rtPA could reduce the clot lysis time for reperfusion by 40% when compared to free rtPA at the same drug dosage. From in vivo targeted thrombolysis in a rat embolic model, pPMNP-rtPA was used at 20% of free rtPA dosage to restore the iliac blood flow in vascular thrombus that was created by injecting a blood clot to the hind limb area.

Preparation and Characterization of Surface Heat Sintered Nanohydroxyapatite and Nanowhitlockite Embedded Poly (Lactic-co-glycolic Acid) Microsphere Bone Graft Scaffolds: In Vitro and in Vivo Studies.

In the context of using bone graft materials to restore and improve the function of damaged bone tissues, macroporous biodegradable composite bone graft scaffolds have osteoinductive properties that allow them to provide a suitable environment for bone regeneration. Hydroxyapatite (HAP) and whitlockite (WLKT) are the two major components of hard tissues such as bone and teeth. Because of their biocompatibility and osteoinductivity, we synthesized HAP (nHAP) and WLKT nanoparticles (nWLKT) by using the chemical precipitation method. The nanoparticles were separately incorporated within poly (lactic-co-glycolic acid) (PLGA) microspheres. Following this, the composite microspheres were converted to macroporous bone grafts with sufficient mechanical strength in pin or screw shape through surface sintering. We characterized physico-chemical and mechanical properties of the nanoparticles and composites. The biocompatibility of the grafts was further tested through in vitro cell adhesion and proliferation studies using rabbit bone marrow stem cells. The ability to promote osteogenic differentiation was tested through alkaline phosphate activity and immunofluorescence staining of bone marker proteins. For in vivo study, the bone pins were implanted in tibia bone defects in rabbits to compare the bone regeneration ability though H&E, Masson's trichrome and immunohistochemical staining. The results revealed similar physico-chemical characteristics and cellular response of PLGA/nHAP and PLGA/nWLKT scaffolds but the latter is associated with higher osteogenic potential towards BMSCs, pointing out the possibility to use this ceramic nanoparticle to prepare a sintered composite microsphere scaffold for potential bone grafts and tissue engineered implants.

Docosahexaenoic Acid-Loaded Polylactic Acid Core-Shell Nanofiber Membranes for Regenerative Medicine after Spinal Cord Injury: In Vitro and In Vivo Study.

Spinal cord injury (SCI) is associated with disability and a drastic decrease in quality of life for affected individuals. Previous studies support the idea that docosahexaenoic acid (DHA)-based pharmacological approach is a promising therapeutic strategy for the management of acute SCI. We postulated that a nanostructured material for controlled delivery of DHA at the lesion site may be well suited for this purpose. Toward this end, we prepare drug-loaded fibrous mats made of core-shell nanofibers by electrospinning, which contained a polylactic acid (PLA) shell for encapsulation of DHA within the core, for delivery of DHA in situ. In vitro study confirmed sustained DHA release from PLA/DHA core-shell nanofiber membrane (CSNM) for up to 36 days, which could significantly increase neurite outgrowth from primary cortical neurons in 3 days. This is supported by the upregulation of brain-derived neurotropic factor (BDNF) and neurotrophin-3 (NT-3) neural marker genes from qRT-PCR analysis. Most importantly, the sustained release of DHA could significantly increase the neurite outgrowth length from cortical neuron cells in 7 days when co-cultured with PLA/DHA CSNM, compared with cells cultured with 3 µM DHA. From in vivo study with a SCI model created in rats, implantation of PLA/DHA CSNM could significantly improve neurological functions revealed by behavior assessment in comparison with the control (no treatment) and the PLA CSNM groups. According to histological analysis, PLA/DHA CSNM also effectively reduced neuron loss and increased serotonergic nerve sprouting. Taken together, the PLA/DHA CSNM may provide a nanostructured drug delivery system for DHA and contribute to neuroprotection and promoting neuroplasticity change following SCI.

Thrombolysis induced by intravenous administration of plasminogen activator in magnetoliposomes: dual targeting by magnetic and thermal manipulation.

In previously published studies, intra-arterial (i.a.), but not intravenous (i.v.) delivery of recombinant tissue-type plasminogen activator (rtPA) immobilized on the surface of magnetic nanoparticles induces thrombolysis by magnetic targeting. We asked whether i.v. delivery of protected rtPA in a thermosensitive magnetoliposome (TML@rtPA) may achieve target thrombolysis. PEGylated TML@rtPA was optimized and characterized; controlled release of rtPA was achieved by thermodynamic and magnetic manipulation in vitro. The lysis index of TML@rtPA incubated with blood at 43 °C vs. 37 °C was 53 ±â€¯11% vs. 81 ±â€¯3% in thromboelastograms, suggesting thermosensitive thrombolysis of TML@rtPA. In a rat embolic model with superfusion of 43 °C saline on a focal spot on the iliac artery with clot lodging, release of rtPA equivalent to 20% regular dose from TML@rtPA administered i.a. vs. i.v. significantly restored iliac blood flow 15 vs. 55 min after clot lodging, respectively. TML@rtPA with magnetic guiding and focal hyperthermia may be potentially amendable to target thrombolysis.

Ibuprofen-Loaded Hyaluronic Acid Nanofibrous Membranes for Prevention of Postoperative Tendon Adhesion through Reduction of Inflammation.

A desirable multi-functional nanofibrous membrane (NFM) for prevention of postoperative tendon adhesion should be endowed with abilities to prevent fibroblast attachment and penetration and exert anti-inflammation effects. To meet this need, hyaluronic acid (HA)/ibuprofen (IBU) (HAI) NFMs were prepared by electrospinning, followed by dual ionic crosslinking with FeCl3 (HAIF NFMs) and covalent crosslinking with 1,4-butanediol diglycidyl ether (BDDE) to produce HAIFB NFMs. It is expected that the multi-functional NFMs will act as a physical barrier to prevent fibroblast penetration, HA will reduce fibroblast attachment and impart a lubrication effect for tendon gliding, while IBU will function as an anti-inflammation drug. For this purpose, we successfully fabricated HAIFB NFMs containing 20% (HAI20FB), 30% (HAI30FB), and 40% (HAI40FB) IBU and characterized their physico-chemical properties by scanning electron microscopy, Fourier transformed infrared spectroscopy, thermal gravimetric analysis, and mechanical testing. In vitro cell culture studies revealed that all NFMs except HAI40FB possessed excellent effects in preventing fibroblast attachment and penetration while preserving high biocompatibility without influencing cell proliferation. Although showing significant improvement in mechanical properties over other NFMs, the HAI40FB NFM exhibited cytotoxicity towards fibroblasts due to the higher percentage and concentration of IBU released form the membrane. In vivo studies in a rabbit flexor tendon rupture model demonstrated the efficacy of IBU-loaded NFMs (HAI30FB) over Seprafilm® and NFMs without IBU (HAFB) in reducing local inflammation and preventing tendon adhesion based on gross observation, histological analyses, and biomechanical functional assays. We concluded that an HAI30FB NFM will act as a multi-functional barrier membrane to prevent peritendinous adhesion after tendon surgery.

Thermosensitive Injectable Hydrogel for Simultaneous Intraperitoneal Delivery of Doxorubicin and Prevention of Peritoneal Adhesion.

To improve intraperitoneal chemotherapy and to prevent postsurgical peritoneal adhesion, we aimed to develop a drug delivery strategy for controlled release of a chemotherapeutic drug from the intraperitoneally injected thermosensitive poly(N-isopropylacrylamide)-based hydrogel (HACPN), which is also endowed with peritoneal anti-adhesion properties. Anticancer drug doxorubicin (DOX) was loaded into the hydrogel (HACPN-DOX) to investigate the chemotherapeutic and adhesion barrier effects in vivo. A burst release followed by sustained release of DOX from HACPN-DOX was found due to gradual degradation of the hydrogel. Cell culture studies demonstrated the cytotoxicity of released DOX toward CT-26 mouse colon carcinoma cells in vitro. Using peritoneal carcinomatosis animal model in BALB/c mice with intraperitoneally injected CT-26 cells, animals treated with HACPN-DOX revealed the best antitumor efficacy judging from tumor weight and volume, survival rate, and bioluminescence signal intensity when compared with treatment with free DOX at the same drug dosage. HACPN (or HACPN-DOX) also significantly reduced the risk of postoperative peritoneal adhesion, which was generated by sidewall defect-cecum abrasion in tumor-bearing BALB/c mice, from gross and histology analyses. This study could create a paradigm to combine controlled drug release with barrier function in a single drug-loaded injectable hydrogel to enhance the intraperitoneal chemotherapeutic efficacy while simultaneously preventing postsurgical adhesion.

Soft Electrochemical Probes for Mapping the Distribution of Biomarkers and Injected Nanomaterials in Animal and Human Tissues.

Monitoring biomarkers and injected theranostic nanomaterials in tissues and organs plays a pivotal role in numerous medical applications ranging from cancer diagnostics to drug delivery. Scanning electrochemical microscopy has been demonstrated as a powerful tool to create highly resolved maps of the distributions of relevant biomolecules in cells and tissues without suffering from the optical interferences of conventional microscopy. We demonstrate for the first time the application of soft microelectrodes brushing in contact mode over large and thick tissues as well as organs that were immersed in an electrolyte solution. Amperometric currents were recorded based on the local flux of redox-active species locally and specifically generated by the biomarkers and nanomaterials to create maps of the biodistribution of graphene oxide nanoribbons in mouse livers, prognostic protein biomarkers in human melanoma and redox-active proteins in mouse heart.

Bone Tissue Engineering with Adipose-Derived Stem Cells in Polycaprolactone/Graphene Oxide/Dexamethasone 3D-Printed Scaffolds.

We fabricated three-dimensional (3D)-printed polycaprolactone (PCL) and PCL/graphene oxide (GO) (PGO) scaffolds for bone tissue engineering. An anti-inflammatory and pro-osteogenesis drug dexamethasone (DEX) was adsorbed onto GO and a 3D-printed PGO/DEX (PGOD) scaffold successfully improved drug delivery with a sustained release of DEX from the scaffold up to 1 month. The physicochemical properties of the PCL, PGO, and PGOD scaffolds were characterized by various analytical techniques. The biological response of these scaffolds was studied for adherence, proliferation, and osteogenic differentiation of seeded rabbit adipose-derived stem cells (ASCs) from DNA assays, alkaline phosphatase (ALP) production, calcium quantification, osteogenic gene expression, and immunofluorescence staining of osteogenic marker proteins. The PGOD scaffold was demonstrated to be the best scaffold for maintaining cell viability, cell proliferation, and osteogenic differentiation of ASCs in vitro. In vivo biocompatibility of PGOD was confirmed from subcutaneous implantation in nude mice where ASC-seeded PGOD can form ectopic bones, demonstrated by microcomputed tomography (micro-CT) analysis and immunofluorescence staining. Furthermore, implantation of PGOD/ASCs constructs into critical-sized cranial bone defects in rabbits form tissue-engineered bones at the defect site, observed using micro-CT and histological analysis.

Solvent-free fabrication of three dimensionally aligned polycaprolactone microfibers for engineering of anisotropic tissues.

Fabrication of aligned microfiber scaffolds is critical in successful engineering of anisotropic tissues such as tendon, ligaments and nerves. Conventionally, aligned microfiber scaffolds are two dimensional and predominantly fabricated by electrospinning which is solvent dependent. In this paper, we report a novel technique, named microfiber melt drawing, to fabricate a bundle of three dimensionally aligned polycaprolactone microfibers without using any organic solvent. This technique is simple yet effective. It has been demonstrated that polycaprolactone microfibers of 10 µm fiber diameter can be directly drawn from a 2 mm orifice. Orifice diameter, temperature and take-up speed significantly influence the final linear density and fiber diameter of the microfibers. Mechanical test suggests that mechanical properties such as stiffness and breaking force of microfiber bundles can be easily adjusted by the number of fibers. In vitro study shows that these microfibers are able to support the proliferation of human dermal fibroblasts over 7 days. In vivo result of Achilles tendon repair in a rabbit model shows that the microfibers were highly infiltrated by tendon tissue as early as in 1 month, besides, the repaired tendon have a well-aligned tissue structure under the guidance of aligned microfibers. However whether these three dimensionally aligned microfibers can induce three dimensionally aligned cells remains inconclusive.

Combination of guided osteogenesis with autologous platelet-rich fibrin glue and mesenchymal stem cell for mandibular reconstruction.

BACKGROUND: This study examined whether a combination of autologous platelet-rich fibrin glue (PRFG) with mesenchymal stem cells (MSCs) and MEDPOR as guided tissue regeneration (GTR) could act as an osteogenic substitute and whether this treatment yields faster new bone formation than MEDPOR alone or PRFG plus MSC. MATERIAL: MSCs were harvested and isolated from the bone marrow of dog ilium. Full-thickness bony defects (1.5×1.5 cm) were created in the bilateral mandible angles of the dog. Treatments for bone defect in each group were as follows: group I (n=4), MEDPOR sheet as GTR and autologous PRFG/MSCs admixtures; group II (n=4), autologous PRFG/MSCs admixtures; group III (n=4), MEDPOR sheet as GTR; and group IV (n=4), control (empty defect). The percentage of new bone regeneration in computerized tomography at 2 months and 4 months was calculated by Analyze version 7.0 software. The mandibles were harvested from all specimens at 4 months, and the grafted sites were evaluated by gross, histologic, and X-ray examination. RESULTS: By radiographic analysis at 16 weeks posttransplantation, it was shown that an average of 72.8%±8.02% new bone formation in group I, 53.34%±6.87% in group II, 26.58%±6.41% in group III, and 15.14%±2.37% in group IV. Histologic examination revealed that the defect was repaired by typical bone tissue in groups I and II, whereas only minimal bone formation with fibrous connection was observed in the groups III and IV group. Besides, muscle incarceration was found in groups II and IV without MEDPOR as GTR. CONCLUSION: Autologous PRFG plus osteoinduced MSCs have good potential for bone regeneration. In combination with MEDPOR as GTR, bone regeneration is enhanced by preventing soft tissue ingrowth hindering bone regeneration.

A bioactive multi-functional heparin-grafted aligned poly(lactide-co-glycolide)/curcumin nanofiber membrane to accelerate diabetic wound healing.

Curcumin is reported to possess excellent efficacy to treat wounds that exhibit impaired healing. Heparin shows high affinity for many growth factors that are key biological mediators during the wound healing process. In this study, we aimed to prepare wound dressing membranes, for sustained release of an exogenous factor curcumin as well as sequestering endogenous growth factors at the wound site, to promote wound healing in diabetic rats. Toward this end, we prepared aligned curcumin-loaded poly(lactide-co-glycolide) (PLGA) nanofiber membranes (PC NFMs), followed by high density surface grafting of heparin to fabricate PLGA/curcumin (PCH) NFMs. Both PC and PCH NFMs show high tensile strength, low cytotoxicity and suitable water vapor transmission rate for application as wound dressings. Nonetheless, the PCH NFM shows higher curcumin release rate than PC due to enhanced hydrophilicity, which leads to higher cell migration rate and induced oxidative stress protection of HS68 fibroblast cells in vitro. In vivo study indicated the PCH exhibits the fastest wound closure rate among all membranes with accelerated re-epithelization rate, higher angiogenesis rate and more collagen deposition at the wound site. The accelerated and better skin tissue regeneration could be suggested to correlate with the multi-functionality of nanofibers, where grafted heparin attracting and stabilizing the growth factors important for wound healing in situ, together with relieving the high oxidative stress and the inflammatory cascade from released curcumin during diabetic wound healing.

Bioactive electrospun silver nanoparticles-containing polyurethane nanofibers as wound dressings.

Nanofibrous membrane (NFM) intended as wound dressing was prepared by electrospinning polyurethane (PU) solution containing silver ion, followed by reduction of silver ion to silver nanoparticles. The electrospun PU membrane has high surface area-to-volume ratio, controlled evaporative water transmission rate, good fluid drainage ability, and excellent antimicrobial activity. With an aim to promote wound healing, collagen was grafted to fiber surface by low temperature oxygen plasma treatment, which could improve surface hydrophilicity and facilitate covalent binding of collagen molecules to the plasma-treated PU surface. A NFM with no bead formation was obtained with fiber diameters around 159 nm. The presence of embedded silver nanoparticles and surface-grafted collagen was confirmed qualitatively and quantitatively. After modification, the NFM's antimicrobial activity improved to approximately 100% inhibition of bacterial growth with concomitant increase of membrane water absorption ability, which facilitates its use as a functional wound dressing. From animal studies, the NFM was better than gauze and commercial collagen sponge wound dressing in wound healing rate.