Three-dimensional finite element analysis on stress distribution after different palatoplasty and levator veli palatini muscle reconstruction.

OBJECTIVES: To establish a three-dimensional finite element model of the upper palate, pharyngeal cavity, and levator veli palatini muscle in patients with unilateral complete cleft palate, simulate two surgical procedures that the two-flap method and Furlow reverse double Z method, observe the stress distribution of the upper palate soft tissue and changes in pharyngeal cavity area after different surgical methods, and verify the accuracy of the model by reconstructing and measuring the levator veli palatini muscle. MATERIALS AND METHODS: Mimics, Geomagic, Ansys, and Hypermesh were applied to establish three-dimensional finite element models of the pharyngeal cavity, upper palate, and levator veli palatini muscle in patients with unilateral complete cleft palate. The parameters including length, angle, and cross-sectional area of the levator veli palatini muscle etc. were measured in Mimics, and two surgical procedures that two-flap method and Furlow reverse double Z method were simulated in Ansys, and the area of pharyngeal cavity was measured by hypermesh. RESULTS: A three-dimensional finite element model of the upper palate, pharyngeal cavity, and bilateral levator veli palatini muscle was established in patients with unilateral complete cleft palate ; The concept of horizontal projection characteristics of the palatal dome was applied to the finite element simulation of cleft palate surgery, vividly simulating the displacement and elastic stretching of the two flap method and Furlow reverse double Z method during the surgical process; The areas with the highest stress in the two-flap method and Furlow reverse double Z method both occur in the hard soft palate junction area; In resting state, as measured, the two flap method can narrow the pharyngeal cavity area by 50.9%, while the Furlow reverse double Z method can narrow the pharyngeal cavity area by 65.4%; The measurement results of the levator veli palatini muscle showed no significant difference compared to previous studies, confirming the accuracy of the model. CONCLUSIONS: The finite element method was used to establish a model to simulate the surgical procedure, which is effective and reliable. The area with the highest postoperative stress for both methods is the hard soft palate junction area, and the stress of the Furlow reverse double Z method is lower than that of the two-flap method. The anatomical conditions of pharyngeal cavity of Furlow reverse double Z method are better than that of two-flap method in the resting state. CLINICAL RELEVANCE: This article uses three-dimensional finite element method to simulate the commonly used two-flap method and Furlow reverse double Z method in clinical cleft palate surgery, and analyzes the stress distribution characteristics and changes in pharyngeal cavity area of the two surgical methods, in order to provide a theoretical basis for the surgeon to choose the surgical method and reduce the occurrence of complications.

The NG2-glia is a potential target to maintain the integrity of neurovascular unit after acute ischemic stroke.

The neurovascular unit (NVU) plays a critical role in health and disease. In the current review, we discuss the critical role of a class of neural/glial antigen 2 (NG2)-expressing glial cells (NG2-glia) in regulating NVU after acute ischemic stroke (AIS). We first introduce the role of NG2-glia in the formation of NVU during development as well as aging-induced damage to NVU and accompanying NG2-glia change. We then discuss the reciprocal interactions between NG2-glia and the other component cells of NVU, emphasizing the factors that could influence NG2-glia. Damage to the NVU integrity is the pathological basis of edema and hemorrhagic transformation, the most dreaded complication after AIS. The role of NG2-glia in AIS-induced NVU damage and the effect of NG2-glia transplantation on AIS-induced NVU damage are summarized. We next discuss the role of NG2-glia and the effect of NG2-glia transplantation in oligodendrogenesis and white matter repair as well as angiogenesis which is associated with the outcome of the patients after AIS. Finally, we review the current strategies to promote NG2-glia proliferation and differentiation and propose to use the dental pulp stem cells (DPSC)-derived exosome as a promising strategy to reduce AIS-induced injury and promote repair through maintaining the integrity of NVU by regulating endogenous NG2-glia proliferation and differentiation.

High-Temperature Polymer Dielectrics Designed Using an Invertible Molecular Graph Generative Model.

Generating new molecules with the desired physical or chemical properties is the key challenge of computational material design. Deep learning techniques are being actively applied in the field of data-driven material informatics and provide a promising way to accelerate the discovery of innovative materials. In this work, we utilize an invertible graph generative model to generate hypothetical promising high-temperature polymer dielectrics. A molecular graph generative model based on the invertible normalizing flow is trained on a data set containing 250k polymer molecular graphs (mostly generated by an RNN-based generative model) to learn the invertible transformations between latent distributions and molecular graph structures. When generating molecular graphs, a sample vector is drawn from the latent space, and then an adjacency tensor and node attribute matrix are generated through two invertible flows in two steps and assembled into a molecular graph. The model has the merits of exact likelihood training and an efficient one-shot generation process. The learned latent space is used to generate polymers with a high glass-transition temperature (Tg) and a wide band gap (Eg) for the application of high-temperature energy storage film capacitors. This work contributes to the efficient design of high-temperature polymer dielectrics by using deep generative models.

Simultaneous Recognition of Dopamine and Uric Acid in the Presence of Ascorbic Acid via an Intercalated MXene/PPy Nanocomposite.

Two-dimensional (2D) MXenes have shown a great potential for chemical sensing due to their electric properties. In this work, a Ti3C2Tx/polypyrrole (MXene/PPy) nanocomposite has been synthesized and immobilized into a glassy carbon electrode to enable the simultaneous recognition of dopamine (DA) and uric acid (UA) under the interference of ascorbic acid (AA). The multilayer Ti3C2Tx MXene was prepared via the aqueous acid etching method and delaminated to a single layer nanosheet, benefiting the in-situ growth of PPy nanowires. The controllable preparation strategy and the compounding of PPy material remain great challenges for further practical application. A facile chemical oxidation method was proposed to regulate magnitude and density during the forming process of PPy nanowire, which promotes the conductivity and the electrochemical active site of this as-prepared nanomaterial. The MXene/PPy nanocomposite-modified electrode exhibited the selective determination of DA and UA in the presence of a high concentration of AA, as well as a wide linear range (DA: 12.5-125 µM, UA: 50-500 µM) and a low detection limit (DA: 0.37 µM, UA: 0.15 µM). More importantly, the simultaneous sensing for the co-existence of DA and UA was successfully achieved via the as-prepared sensor.

OsHK3 is a crucial regulator of abscisic acid signaling involved in antioxidant defense in rice.

In this study, the role of the rice (Oryza sativa L.) histidine kinase OsHK3 in abscisic acid (ABA)-induced antioxidant defense was investigated. Treatments with ABA, H2 O2 , and polyethylene glycol (PEG) induced the expression of OsHK3 in rice leaves, and H2 O2 is required for ABA-induced increase in the expression of OsHK3 under water stress. Subcellular localization analysis showed that OsHK3 is located in the cytoplasm and the plasma membrane. The transient expression analysis and the transient RNA interference test in rice protoplasts showed that OsHK3 is required for ABA-induced upregulation in the expression of antioxidant enzymes genes and the activities of antioxidant enzymes. Further analysis showed that OsHK3 functions upstream of the calcium/calmodulin-dependent protein kinase OsDMI3 and the mitogen-activated protein kinase OsMPK1 to regulate the activities of antioxidant enzymes in ABA signaling. Moreover, OsHK3 was also shown to regulate the expression of nicotinamide adenine dinucleotide phosphate oxidase genes, OsrbohB and OsrbohE, and the production of H2 O2 in ABA signaling. Our data indicate that OsHK3 play an important role in the regulation of ABA-induced antioxidant defense and in the feedback regulation of H2 O2 production in ABA signaling.

Three novel lanthanide metal-organic frameworks (Ln-MOFs) constructed by unsymmetrical aromatic dicarboxylatic tectonics: synthesis, crystal structures and luminescent properties.

Three novel Ln(III)-based coordination polymers, {[Ln2 (2,4-bpda)3 (H2O)x]·yH2O}n (Ln = La (III) (1), x = 2, y = 0, Ce (III) (2), Pr (III) (3), x = 4, y = 1) (2,4-H2bpda = benzophenone-2,4-dicarboxylic acid) have been prepared via a solvothermal method and characterized by elemental analysis, IR, and single-crystal X-ray diffraction techniques. Complex 1 exhibits a 3D complicated framework with a new 2-nodal (3,7)-connected (42·5) (44·51·66·8) topology. Complexes 2 and 3 are isomorphous, and feature a 3D 4-connected (65·8)-CdSO4 network. Moreover, solid-state properties such as thermal stabilities and luminescent properties of 1 and 2 were also investigated. Complex 1 crystallized in a monoclinic space group P21/c with a = 14.800 (3), b = 14.500 (3), c = 18.800 (4) Å, ß = 91.00 (3), V = 4033.9 (14) Å3 and Z = 4. Complex 2 crystallized in a monoclinic space group Cc with a = 13.5432 (4), b = 12.9981 (4), c = 25.7567 (11) Å, ß = 104.028 (4), V = 1374.16 (7) Å3 and Z = 4.

Proteomic profile of tissue-derived extracellular vesicles from benign odontogenic lesions.

BACKGROUND: Benign odontogenic lesions (BOLs) can cause severe jaw bone defects and compromise the quality of life of patients. Extracellular vesicles (EVs) are well-established and versatile players in mediating pathophysiological events. EVs in the interstitial space (tissue-derived EVs or Ti-EVs) possess higher specificity and sensitivity in disease-related biomarker discovery. However, the role of Ti-EV-loaded proteins in mediating the development of BOLs has remained untapped. Herein, we aim to explore the contribution of Ti-EV-loaded proteins to the development of BOLs. METHODS: Samples were obtained from 3 with dental follicle, 3 with dentigerous cyst (DC), 7 with odontogenic keratocyst (OKC), and 3 patients with ameloblastoma (AM). Tissue-derived EVs were then extracted, purified, and validated using ultracentrifugation, transmission electron microscopy, and western blotting. Proteins from Ti-EVs were analyzed using LC-ESI tandem mass spectroscopy and differentially expressed proteins were screened, which was then validated by immunohistochemistry and immunofluorescence assays. RESULTS: The protein profile of Ti-EVs in each group was mapped by LC-MS analysis. The top 10 abundant proteins in BOL-derived Ti-EVs were COL6A3, COL6A1, ALB, HIST1H4A, HBB, ACTB, HIST1H2BD, ANXA2, COL6A2 and FBN1. Additionally, unique proteins in the Ti-EVs from various lesions were identified. Moreover, focal adhesion kinase (FAK) and myeloid differentiation primary response 88 (MyD88) showed higher expressions in Ti-EVs derived from OKC and AM, which were confirmed by immunohistochemistry and immunofluorescence staining. CONCLUSIONS: Ti-EVs containing FAK and MyD88 might be related to the development of OKC and AM, which can be potential therapeutic targets.

Engineering marine phospholipid nanoliposomes via glycerol-infused proliposomes: Mechanisms, strategies, and versatile applications in scalable food-grade nanoliposome production.

This study presents a novel approach using polyol-based proliposome to produce marine phospholipids nanoliposomes. Proliposomes were formulated by blending glycerol with phospholipids across varying mass ratios (2:1 to 1:10) at room temperature. Analysis employing polarized light microscopy, FTIR, and DSC revealed that glycerol disrupted the stacked acyl groups within phospholipids, lowering the phase transition temperature (Tm). Krill oil phospholipids (KOP) proliposomes exhibited superior performance in nanoliposomes formation, with a mean diameter of 125.60 ± 3.97 nm, attributed to the decreased Tm (-7.64 and 7.00 °C) compared to soybean phospholipids, along with a correspondingly higher absolute zeta potential (-39.77 ± 1.18 mV). The resulting KOP proliposomes demonstrated liposomes formation stability over six months and under various environmental stresses (dilution, thermal, ionic strength, pH), coupled with in vitro absorption exceeding 90 %. This investigation elucidates the mechanism behind glycerol-formulated proliposomes and proposes innovative strategies for scalable, solvent-free nanoliposome production with implications for functional foods and pharmaceutical applications.

TiO2 nanoparticle thin film-coated optical fiber Fabry-Perot sensor.

In this paper, a novel TiO(2) nanoparticle thin film coated optical fiber Fabry-Perot (F-P) sensor had been developed for refractive index (RI) sensing by monitoring the shifts of the fringe contrast in the reflectance spectra. Using in situ liquid phase deposition approach, the TiO(2) nanoparticle thin film could be formed on the fiber surface in a controlled fashion. The optical properties of as-prepared F-P sensors were investigated both theoretically and experimentally. The results indicated that the RI sensitivity of F-P sensors could be effectively improved after the deposition of nanoparticle thin-films. It was about 69.38 dB/RIU, which was 2.6 times higher than that of uncoated one. The linear RI measurement range was also extended from 1.333~1.457 to 1.333~1.8423. More importantly, its optical properties exhibited the unique temperature-independent performance. Therefore, owing to these special optical properties, the TiO(2) nanoparticle thin film coated F-P sensors have great potentials in medical diagnostics, food quality testing, environmental monitoring, biohazard detection and homeland security, even at elevated temperature.

Ultrasound-modulated shape memory and payload release effects in a biodegradable cylindrical rod made of chitosan-functionalized PLGA microspheres.

Minimally invasive implants and/or scaffolds integrated with multiple functionalities are of interest in the clinical settings. In this paper, chitosan (CTS) functionalized poly(lactic-co-glycolic acid) (PLGA) microspheres containing a model payload, lysozyme (Lyz), were prepared by a water-in-oil-in-water emulsion method, from which cylindrical shaped rod (5 mm in diameter) was fabricated by sintering the composite microspheres in a mold. High-intensity focused ultrasound (HIFU) was then employed as a unique technique to enable shape memory and payload release effects of the three-dimensional (3-D) structure. It was found that incorporation of CTS into PLGA microspheres could regulate the transition temperature Ttrans of the microsphere from 45 to 50 °C and affect shape memory ratio of the fabricated cylindrical rod to some extent. Shape memory test and drug release assay proved that HIFU could modulate the shape recovery process and synchronize the release kinetics of the encapsulated Lyz in the rod in a switchable manner. Moreover, the two processes could be manipulated by varying the acoustic power and insonation duration. Mechanical tests of the microspheres-based rod before and after ultrasound irradiation revealed its compressive properties in the range of trabecular bone. Examination of the degradation behavior indicated that the introduction of CTS into the PLGA microspheres also alleviated acidic degradation characteristic of the PLGA-dominant cylindrical rod. With HIFU, this study thus demonstrated the desired capabilities of shape recovery and payload release effects integrated in one microspheres-based biodegradable cylindrical structure.

Structural and enzymatic characterization of the sialidase SiaPG from Porphyromonas gingivalis.

The sialidases, which catalyze the hydrolysis of sialic acid from extracellular glycoconjugates, are a group of major virulence factors in various pathogenic bacteria. In Porphyromonas gingivalis, which causes human periodontal disease, sialidase contributes to bacterial pathogenesis via promoting the formation of biofilms and capsules, reducing the ability for macrophage clearance, and providing nutrients for bacterial colonization. Here, the crystal structure of the P. gingivalis sialidase SiaPG is reported at 2.1 Šresolution, revealing an N-terminal carbohydrate-binding domain followed by a canonical C-terminal catalytic domain. Simulation of the product sialic acid in the active-site pocket together with functional analysis enables clear identification of the key residues that are required for substrate binding and catalysis. Moreover, structural comparison with other sialidases reveals distinct features of the active-site pocket which might confer substrate specificity. These findings provide the structural basis for the further design and optimization of effective inhibitors to target SiaPG to fight against P. gingivalis-derived oral diseases.

Effects of molecular weights on the absorption, distribution and urinary excretion of intraperitoneally administrated carboxymethyl chitosan in rats.

Carboxymethyl chitosan (CM-chitosan) is one of water-soluble derivatives of chitosan. Numerous studies have been focused on its applications as pharmaceutical excipient, bioactive reagent and nontoxic drug carrier. Like other polysaccharides, CM-chitosan is inhomogenous in molecular weight. Originations and preparation procedures considerably influence its molecular weight and molecular weight distributions. Understanding the molecular weight related biological behaviour of this inhomogenous glycopolymer in vivo were crucial for the quality control and clinical applications of chitosan and chitosan based medical devices. In this study, we investigated the effects of molecular weights on the absorption, distribution, degradation and urinary excretion of the fluorescein isothiocyanate-labeled CM-chitosan in rats. The results indicated that molecular weight significantly influenced the uptake of CM-chitosan from the lumen of abdomen and blood vessels to peripheral tissues, the distribution of this chemical and urinary excretion after intraperitoneal administration. These findings provided an important reference for the clinical applications of this versatile derivative of chitosan as postsurgical and other biomedical materials and important clues for the exploitation of CM-chitosan based drug targeting and delivery systems.

Conversion of cellulose into levulinic acid under the catalysis of Brønsted acidic ionic liquid and erbium chloride in water.

We propose a new approach for the synergistically catalytic conversion of cellulose to levulinic acid (LA) in water by SO3H-functionalized ionic liquid (SFIL) and lanthanide chloride (LnCl3). Compared with using 1-methyl-3-(3-sulfopropyl)imidazolium chloride ([MIMPS]Cl) only, the LA yield using [MIMPS]Cl and ErCl3 increased by 14.4% and 13.6% at 50 mol% of IL and 30 mol% of IL, respectively. Moreover, the combined [MIMPS]Cl and ErCl3 system can tolerate high concentrations of substrates and maintain high activity at eleven runs. We also investigated the effects of the cation structure of ionic liquids (alkyl chain length, hydroxyl groups on the side chains, and aromatic properties) on LA production. The observations can provide useful information for designing efficient ionic liquid catalysts for biomass utilization.

A Biodegradable and Recyclable Piezoelectric Sensor Based on a Molecular Ferroelectric Embedded in a Bacterial Cellulose Hydrogel.

Currently, various electronic devices make our life more and more safe, healthy, and comfortable, but at the same time, they produce a large amount of nondegradable and nonrecyclable electronic waste that threatens our environment. In this work, we explore an environmentally friendly and flexible mechanical sensor that is biodegradable and recyclable. The sensor consists of a bacterial cellulose (BC) hydrogel as the matrix and imidazolium perchlorate (ImClO4) molecular ferroelectric as the functional element, the hybrid of which possesses a high sensitivity of 4 mV kPa-1 and a wide operational range from 0.2 to 31.25 kPa, outperforming those of most devices based on conventional functional biomaterials. Moreover, the BC hydrogel can be fully degraded into glucose and oligosaccharides, while ImClO4 can be recyclable and reused for the same devices, leaving no environmentally hazardous electronic waste.

Effects of carboxymethyl chitosan on the blood system of rats.

Carboxymethyl chitosan (CM-chitosan), a derivative of chitosan, was extensively studied in the biomedical materials field for its beneficial biological properties of hemostasis and stimulation of healing. However, studies examining the safety of CM-chitosan in the blood system are lacking. In this study CM-chitosan was implanted into the abdominal cavity of rats to determine blood indexes at different times and to evaluate the effects of CM-chitosan on the blood system of rats. Coagulation function was reflected by thrombin time (TT), prothrombin time (PT), activated partial thromboplatin time (APTT), fibrinogen (FIB) and platelet factor 4 (PF4) indexes; anti-coagulation performance was assessed by the index of antithrombinIII (ATIII); fibrinolytic function was reflected by plasminogen (PLG) and fibrin degradation product (FDP) indexes; and blood viscosity (BV) and plasma viscosity (PV) indexes reflected hemorheology. Results showed that CM-chitosan has no significant effects on the blood system of rats, and provides experimental basis for CM-chitosan to be applied in the field of biomedical materials.

Disturbed tooth germ development in the absence of MINT in the cultured mouse mandibular explants.

The Msx2-interacting nuclear target protein (MINT) is a nuclear matrix protein that regulates the development of many tissues. However, little is known regarding the role of MINT in tooth development. In this study, we prepared polyclonal antibodies against MINT, and found that that MINT was expressed in different cells at each stage of tooth germ development by immunohistochemistry. The role of MINT in tooth development was further illustrated by the misshapen and severely hypoplastic tooth organ in the cultured mandibular explants of MINT deficient mice. From the initiation to cap stage, the differences between mutants and wild-type molars were more and more distinguished histologically. In the MINT-deficient mandibular explants, the tooth germ was reduced in the overall size and lacked enamel knot, with abnormal dental lamina and collapsed stellate reticulum. Furthermore, the BrdU incorporation experiment showed that the proliferation activity was significantly reduced in MINT-deficient dental epithelium. Our results suggest that MINT plays an important role in tooth development, in particular, epithelial morphogenesis.

Riboflavin-based carbon dots with high singlet oxygen generation for photodynamic therapy.

Photodynamic therapy, as an effective treatment for superficial tumors, has attracted more and more attention. The development of safe, biocompatible and in vivo photosensitive materials is helpful to promote photodynamic therapy. Here we report green fluorescent carbon quantum dots prepared from a natural vitamin, riboflavin (VB2), as a photosensitizer. The VB2-based carbon dots have excellent water solubility and biocompatibility, and their singlet oxygen generation ability is much stronger than that of riboflavin itself. Through endocytosis, the carbon dots can easily enter the cells and show bright green fluorescence. In vivo experiments show that after photodynamic therapy the carbon dots can significantly inhibit the growth of tumors, and will not have toxic and side effects on other organs.

Pharmacokinetics and biodegradation mechanisms of a versatile carboxymethyl derivative of chitosan in rats: in vivo and in vitro evaluation.

Carboxymethyl chitosan (CM-chitosan), which is a water-soluble derivative of chitosan, has attracted much attention as a new biomedical material. The safety study of this material was persuasive for its potential application. The present study was conducted to assess the tissue distribution, pharmacokinetics, biodegradation mechanism, and excretion of CM-chitosan in rats. After the rats were intraperitoneally injected at the dose of 50 mg/kg, the fluorescein isothiocyanate (FITC)-labeled CM-chitosan was absorbed rapidly and distributed to different organs, including liver, spleen, and kidney. The highest level of CM-chitosan was found in liver. It was at the level of 1.6 +/- 0.6 mg/liver and made up approximately 10-22% of the total injected FTC-CM-chitosan. Urinary excretion was the predominant way of excretion of FITC-labeled CM-chitosan, and 85% of the dose was excreted in urine over the period of 11 days. The molecular weights of body distributed FTC-CM-chitosan and urinary excreted FTC-CM-chitosan were analyzed by gel chromatography. The results indicated that the FTC-CM-chitosan was degraded in abdominal dropsy. The absorbed CM-chitosan forms were found with a relatively high molecular weight (approximately 300 kDa), whereas the molecular weight of the urinary excreted FTC-CM-chitosan was less than 45 kDa. In vitro research revealed that the CM-Chi was also degradable in plasma and homogenate of liver. The CM-chitosan with a molecular weight of approximately 800k was thoroughly degraded to a small molecule after it was incubated in homogenate of liver at 37 degrees C for 24 h. The results suggested that the liver plays a central role in biodegradation of CM-chitosan. The excellent biodegradability of CM-chitosan could potentially contribute to the clinical applications. The results also provide important clues for further modification of CM-chitosan as the postsurgical and other biomedical materials.

Performance of polyvinyl pyrrolidone-isatis root antibacterial wound dressings produced in situ by handheld electrospinner.

Antibacterial dressings are an increasingly important tool for the prevention and management of wound infections, particularly in light of concerns surrounding conventional drug-resistant antibiotics. Handheld electrospinning devices provide opportunities for the rapid application of antibacterial dressing materials to wounds, but spinning formulations need to be compatible with live biological surfaces. We report the development of a new antibacterial formulation compatible with handheld electrospinning, and its manufacture directly on a wound site. Nanofibrous dressing mats were produced from polyvinyl pyrrolidone (PVP) containing isatis root (Indigowoad root or Ban-Lan-Gen), a traditional Chinese medicine, commonly used for the treatment of infectious disease. The resulting wound dressing mats of PVP/isatis root exhibited well-defined fibrous structures and excellent surface wetting, and permeability characteristics. The presence of isatis root conferred antibacterial activity against gram negative and gram positive strains. Moreover, in a Kunming mouse skin injury model, direct electrospinning of PVP/isatis root formulations on to wound sites produced near complete wound closure after 11 days and epidermal repair in histological studies.

Monodispersed polymeric nanocapsules: spontaneous evolution and morphology transition from reducible hetero-PEG PICmicelles by controlled degradation.

In this communication, a novel "self-templating" strategy was used to prepare uniform and biocompatible nanocapsules by the addition of a reduction agent (i.e., DTT) into a solution of highly monodispersed PICmicelles bearing a heterodetachable PEG corona. PEG chains were released from PICmicelle shells following disulfide reduction which leads a spontaneous and drastic morphology evolution from micelles to vesicles induced by the decrease of the PEG weight fraction. Formation of uniform nanocapsules with controllable capsule size was achieved by careful control of the micelle composition and molecular weight of homo-P[Asp(DET)].