Grit blasting of medical stainless steel: implications on its corrosion behavior, ion release and biocompatibility.

This study reports on the biocompatibility of 316 LVM steel blasted with small and rounded ZrO(2) particles or larger and angular shaped Al(2)O(3) particles. The effect of blasting on the in vitro corrosion behavior and the associated ion release is also considered. Surface of Al(2)O(3) blasted samples was rougher than that of ZrO(2) blasted samples, which was also manifested by a higher surface area. Compared to the polished alloy, blasted steels exhibited a lower corrosion resistance at the earlier stages of immersion, particularly when using Al(2)O(3) particles. With increasing immersion time, blasted samples experienced an improvement of the corrosion resistance, achieving impedance values typical of passive alloys. Blasting of the alloy led to an increase in Fe release and the leaching of Ni, Mn, Cr and Mo. On all surfaces, ion release is higher during the first 24 h exposure and tends to decrease during the subsequent exposure time. Despite the lower corrosion resistance and higher amount of ions released, blasted alloys exhibit a good biocompatibility, as demonstrated by culturing osteoblastic cells that attached and grew on the surfaces.

Corrosion behaviour and biocompatibility of a novel Ni-free intermetallic coating growth on austenitic steel by hot dipping in an Al-12.6%Si alloy.

Commercial 316 LVM austenitic stainless steel samples have been coated by immersion in a bath of molten Al-12.6%Si alloy for 120 s. The coating consists of the Al(12)(Fe,Cr)(3)Si(2) intermetallic. In vitro corrosion behaviour has been evaluated in the Ringer's solution by means of potentiodynamic curves and electrochemical impedance spectroscopy. The results reveal that the coated specimens exhibit lower susceptibility to localised corrosion with respect to the substrate. XPS analysis suggests that the ennoblement of the pitting potential is due to the formation of a chromium oxyhydroxide containing passive layer. The intermetallic coating shows a good biocompatibility, as demonstrated by culturing human mesenchymal stem cells isolated from bone marrow which attached, grew and differentiated to the osteoblastic lineage to a similar extent on coated and bare steels. In summary, this study proposes a method that generates Ni-free coatings of the stainless steel with useful properties for biomedical applications.

Development of biocompatible and fully bioabsorbable PLA/Mg films for tissue regeneration applications.

During recent years, Mg reinforced polylactic acid (PLA) composites have emerged as potential biocompatible and bioabsorbable materials for biomedical applications. It has been shown that Mg particles added to a matrix based on a biodegradable polymer can address the lack of bioactivity and the low mechanical properties of the polymers and, furthermore, it can counteract the detrimental effects associated to the high degradation rate of Mg, as alkalinization and elevated H2 release. Additionally, the polymer can protect the Mg particles, by tailoring their degradation rate. Former processing of these composites performed by extrusion, compression and injection molding employed Mg contents up to 10 wt%. Higher amounts of Mg resulted in heterogeneous materials and thermally degraded matrices, with the corresponding higher degradation rate. In the present work, Mg reinforced PLA films with Mg content as high as 50 wt% were obtained without compromising the thermal stability of the polymer. Firstly, a successful dispersion of Mg microparticles was achieved by a breakthrough in processing introducing a colloidal step where organic additives were added to modify the Mg particle surface and promote a chemically stable suspension. The resulting colloidal suspension was then used as feedstock to obtain composite films by tape casting. The films show advantageous in vitro behaviour in terms of degradation, hydrogen release and oxygen permeability. In addition, the viability with fibroblast cells (MEF) opens a window of opportunity for these composite films as bioabsorbable material for tissue engineering and wound dressing applications. STATEMENT OF SIGNIFICANCE: Magnesium materials have extraordinary biodegradable properties and bioactive behavior due to release of Mg2+ ions, which offer a promising opportunity for their applicability as biomaterials for tissue regeneration. However, Mg is one of the most reactive metals with a high degradation rate. In contact with water produces H2, associated with a risk of failure of the implant. One alternative to minimize this drawback is the use of Mg particles surrounded by a biodegradable biocompatible polymer such as polylactic acid (PLA) to obtain PLA/Mg composites. In this work we processed Mg reinforced PLA in the shape of films that would be suitable for tissue regeneration. In vitro behavior of PLA/Mg films demonstrated that Mg2+ ions increase the fibroblast cells growth.

Effect of UV irradiation on the surface Gibbs energy of Ti6Al4V and thermally oxidized Ti6Al4V.

Thermal oxidation of Ti6Al4V increases the thickness, modifies the structure, and changes the amount of alloying elements of the surface titanium dioxide layer with respect to the spontaneous passive layer of Ti6Al4V. The effects on the surface properties of Ti6Al4V and thermally oxidized Ti6Al4V after different periods of UV irradiation have been studied by measurement of water, formamide, and diiodomethane contact angles. The rate of modification of the water contact angle with the irradiation time is dependent on the surface treatment, but the water adhesion work, after an initial energetic step, follows a similar trend for both. Application of the Young equation together with the van Oss approach allowed evaluation of the surface Gibbs energy of the alloys. Similar to the water adhesion work, the surface Gibbs energy dependence on the irradiation time follows a similar trend for both samples and it is due to the change of the electron-donor parameter of the acid-base component. Also, a linear relationship common for both samples has been obtained between the cosines of the water contact angle and the formamide or diiodomethane contact angle. These facts indicate that the surface modification continuously produced by the UV irradiation is similar all along the process and similar for both samples after an energetic threshold for the thermally oxidized sample. It has been also tested that the hydrophilic-hydrophobic conversion is reversible for Ti6Al4V and Ti6Al4V thermally treated.

Thermal oxidation enhances early interactions between human osteoblasts and alumina blasted Ti6Al4V alloy.

Oxidation of Ti6Al4V at 500 degrees C for 1 h in air results in the formation of an outer ceramic layer that improves osteoblast behavior and decreases Ti and Al ion release. In this work, alumina blasted Ti6Al4V alloy has been thermally treated and its in vitro biocompatibility has been assessed. Roughness of the blasted alloy was not found significantly altered after heat treatment while chemical surface analysis indicated an increase in stable TiO(2) and Al(2)O(3) oxides. Cell attachment, spreading, cytoskeleton organization as well as cell proliferation, viability, and procollagen I peptide secretion of human primary osteoblasts, impaired on alumina blasted Ti6Al4V, were found to be greatly enhanced on the thermally oxidized blasted alloy. Other informative markers of the osteoblastic phenotype such as alkaline phosphatase, osteocalcin, osteoprotegerin, and mineralized nodule formation were evaluated and indicated that osteoblasts responded at the same extent on untreated and thermally treated blasted alloys. Taken together, our in vitro results indicate that thermal oxidation of alumina blasted Ti6Al4V may favor successful osseointegration by promoting early interactions of osteoblastic cells and the modified surface alloy.

Potential of FeAlCr intermetallics reinforced with nanoparticles as new biomaterials for medical devices.

Novel FeAlCr oxide dispersion strengthened intermetallics that are processed by powder metallurgy have been developed as potential biomaterials. The alloys exhibit a small grain size and a fine dispersion of yttria provides the material with a high yield strength and depending on the alloy composition good ductility (up to 5%). The biocompatibility of the alloy was assessed in comparison with commercial alumina. Saos-2 osteoblast-like cells were either challenged with mechanically alloyed particles, or seeded onto solid samples. Viability and proliferation of cells were substantially unaffected by the presence of a high concentration of particles (1 mg/mL). Solid samples of novel FeAlCr intermetallic have shown a good biocompatibility in vitro, often approaching the behavior of materials well known for their biological acceptance (e.g. alumina). It has been found that osteoblasts are able to produce ALP, a specific marker of cells with bone-forming activity. In this respect, ALUSI alloys hold the promise to be suitable substrate for bone integration. The finding of no cytotoxic effect in the presence of the alloy particles is a reliable proof of the absence of acute toxicity of the material.

Effect of Mg content on the thermal stability and mechanical behaviour of PLLA/Mg composites processed by hot extrusion.

In the field of bioabsorbable composites for biomedical applications, extrusion has been employed as a method to prepare homogeneous blends of polymeric matrices with bioactive ceramic fillers. In this work, the suitability of processing poly-l-lactic acid/Magnesium (PLLA/Mg) composites by hot extrusion has been assessed by a systematic characterization of PLLA/Mg composites containing different amounts of Mg particles up to 7wt%. The results show that extrusion causes a reduction of almost 20% in the viscosity average molecular weight of PLLA, which further decreases with increasing Mg content. Extrusion gave always rise to a homogeneous distribution of Mg particles within the PLLA matrix. This composite processing was not compromised by the degradation of the polymeric matrix because the processing temperature was always below the onset degradation temperature. In the processing conditions employed in the present work, degradation of the composite slightly increases as more Mg is added up to 5wt%, but is very high at 7wt%. This was also evident from the mechanical behaviour, so that Mg particles improved the stiffness and compression strength of neat PLLA until 5wt% of Mg content, which dropped drastically when the material had 7wt% of Mg. The filler strengthening factor decreases with the increment in Mg content. In order to obtain an optimised contribution of Mg particles, a balance between thermal degradation and mechanical resistance of PLLA must be achieved.

Assessment of mechanical behavior of PLA composites reinforced with Mg micro-particles through depth-sensing indentations analysis.

This work deals with the mechanical characterization by depth-sensing indentation (DSI) of PLLA and PLDA composites reinforced with micro-particles of Mg (up to 15wt%), which is a challenging task since the indented volume must provide information of the bulk composite, i.e. contain enough reinforcement particles. The composites were fabricated by combining hot extrusion and compression moulding. Physico-chemical characterization by TGA and DSC indicates that Mg anticipates the thermal degradation of the polymers but does not compromise their stability during processing. Especial emphasis is devoted to determine the effect of strain rate and Mg content on mechanical behavior, thus important information about the visco-elastic behavior and time-dependent response of the composites is obtained. Relevant for the intended application is that Mg addition increases the elastic modulus and hardness of the polymeric matrices and induces a higher resistance to flow. The elastic modulus obtained by DSI experiments shows good agreement with that obtained by uniaxial compression tests. The results indicate that DSI experiments are a reliable method to calculate the modulus of polymeric composites reinforced with micro-particles. Taking into consideration the mechanical properties results, PLA/Mg composite could be used as substitute for biodegradable monolithic polymeric implants already in the market for orthopedics (freeform meshes, mini plates, screws, pins, …), craniomaxillofacial, or spine.

Antibacterial effect of novel biodegradable and bioresorbable PLDA/Mg composites.

Polylactic acid/Mg composites have been recently proposed for biodegradable osteosynthesis devices because, with regards to the neat polymer, they combine an enhanced biocompatibility and bioactivity with better mechanical properties, particularly creep strength. A question still arises about their bacterial behavior. For this purpose, composites of poly-L-D-lactic acid (PLDA) loaded with 1 and 10 wt.% of Mg microparticles were evaluated using Staphylococcus epidermidis, with special emphasis on the study of bacterial adhesion and biofilm formation. During biofilm formation the bacteria viability of the composites decreased up to 65.3% with respect to PLDA. These antibacterial properties do not compromise the cytocompatibility of the material as the composites enhanced the viability of mesenchymal stem cells and their osteogenic commitment. These findings provide an important added value to the biodegradable and biocompatible PLDA/Mg composites for the manufacture of osteosynthesis devices.

Osteoblast response to plasma-spray porous Ti6Al4V coating on substrates of identical alloy.

We have evaluated the in-vitro biocompatibility of Ti6Al4V alloy coated by plasma spraying with an identical alloy. These surfaces are widely used in cementless prosthetic components, although osteoblasts behavior on this treated alloy has not been evaluated to date. Cross sectional examination revealed a thick and rough coating of identical composition without sign of delamination. Within the coating, small discontinuities and nonconnected pores were observed. Osteoblast response was evaluated by assessing cell adhesion, proliferation, and differentiation of primary cultures of human osteoblastic cells. Compared to the polished alloy, osteoblast adhesion measured as cell attachment and actin network reorganization was delayed on the plasma-sprayed surface. Cell proliferation and viability were also impaired on the rough surface. Several informative markers of osteoblastic differentiation such as procollagen I peptide, alkaline phosphatase, osteocalcin, osteoprotegerin, and mineralized nodule formation were evaluated and indicated that the plasma-sprayed alloy favored a more differentiated phenotype than polished alloy. Taken together, our in vitro results indicate that successful osseointegration of plasma spraying of Ti6Al4V with an identical alloy is mediated by modulation of osteoblastic differentiation and mineralization.

Looking at the micro-topography of polished and blasted Ti-based biomaterials using atomic force microscopy and contact angle goniometry.

Surface topography of polished and blasted samples of a Ti6Al4V biomaterial has been studied using an atomic force microscope. Surface RMS roughness and surface area have been measured at different scales, from 1 to 50 microm, while at distances below 10 microm the surface RMS roughness in both kinds of samples is not very different, this difference becomes significant at larger scanning sizes. This means that the surface roughness scale that could have a main role in cell adhesion varies depending on the size, shape and flexibility of participating cells. This consideration suggests that in cell-material interaction studies, surface roughness should not be considered as an absolute and independent property of the material, but should be measured at scales in the order of the cell sizes, at least if a microscopic interpretation of the influence of roughness on the adhesion is intended. The microscopic information is contrasted with that coming from a macroscopic approach obtained by contact angle measurements for polar and non-polar liquids whose surface tension is comprised in a broad range. Despite the very large differences of contact angles among liquids for each surface condition, a similar increase for the blasted surface with respect to the polished has been found. Interpretation of these results are in accordance with the microscopic analysis done through the use of a functional roughness parameter, namely the valley fluid retention index, evaluated from the AFM images, which has been shown not to correlate with the RMS roughness, one of the most commonly used roughness parameter.

Nanomechanical characterization of alumina coatings grown on FeCrAl alloy by thermal oxidation.

This work studies the feasibility of using repetitive-nano-impact tests with a cube-corner tip and low loads for obtaining quantitative fracture toughness values in thin and brittle coatings. For this purpose, it will be assumed that the impacts are able to produce a cracking, similar to the pattern developed for the classical fracture toughness tests in bulk materials, and therefore, from the crack developed in the repetitive impacts it will be possible to evaluate the suitability of the classical indentation models (Anstins and Laugier) for measuring fracture toughness. However, the length of this crack has to be lower than 10% of the total coating thickness to avoid substrate contributions. For this reason, and in order to ensure a small plastic region localized at the origin of the crack tip, low load values (or small distance between the indenter tip and the surface) have to be used. In order to demonstrate the validity of this technique, repetitive-nano-impact will be done in a fine and dense oxide layer (α-Al2O3), which has been developed on the top of oxide dispersion strengthened (ODS) FeCrAl alloys (PM 2000) by thermal oxidation at elevated temperatures. Moreover, it will be shown how it is possible to know with each new impact the crack geometry evolution from Palmqvist crack to half-penny crack, being able to study the proper evolution of the different values of fracture toughness in terms of both indentation models and as a function of the strain rate, ε̇, decreasing. Thereby, fracture toughness values for α-Al2O3 layer decrease from ~4.40MPam , for high ϵ̇ value (10(3)s(-1)), to ~3.21MPam, for quasi-static ϵ̇ value (10(-3)s(-1)). On the other hand, ϵ̇ a new process to obtain fracture toughness values will be analysed, when the classical indentation models are not met. These values are typically found in the literature for bulk α-Al2O3, demonstrating the use of repetitive-nano-impact tests which not only provide qualitative information about fracture resistance of the materials but it also can be used to obtain quantitative information as fracture toughness values in the case of brittle materials.

Thermal oxidation of medical Ti6Al4V blasted with ceramic particles: Effects on the microstructure, residual stresses and mechanical properties.

Roughening of Ti6Al4V by blasting with alumina or zirconia particles improves the mechanical fixation of implants by increasing the surface area available for bone/implant apposition. Additional thermal oxidation treatments of the blasted alloy have already shown to be a complementary low-cost solution to enhancing the in vitro biocompatibility and corrosion resistance of the alloy. In this work, the effects of oxidation treatment on a grit blasted Ti6Al4V biomedical alloy have been analysed in order to understand the net effect of the combined treatments on the alloy fatigue properties. Synchrotron radiation diffraction experiments have been performed to measure residual stresses before and after the treatments and microstructural and hardness changes have been determined. Although blasting of Ti6Al4V with small spherical zirconia particles increases the alloy fatigue resistance with respect to unblasted specimens, fatigue strength after oxidation decreases below the unblasted value, irrespective of the type of particle used for blasting. Moreover, at 700°C the as-blasted compressive residual stresses (700MPa) are not only fully relaxed but even moderate tensile residual stresses, of about 120MPa, are found beneath the blasted surfaces. Contrary to expectations, a moderate increase in hardness occurs towards the blasted surface after oxidation treatments. This can be attributed to the fact that grit blasting modifies the crystallographic texture of the Ti6Al4V shifting it to a random texture, which affects the hardness values as shown by additional experiments on cold rolled samples. The results indicate that the oxidation treatment performed to improve biocompatibility and corrosion resistance of grit blasted Ti6Al4V should be carried out with caution since the alloy fatigue strength can be critically diminished below the value required for high load-bearing components.

In vitro degradation of biodegradable polylactic acid/magnesium composites: Relevance of Mg particle shape.

Absorbable medical devices must be developed in order to have an appropriate degradation rate in agreement with the healing rate of bone in the implantation site. In this work, biodegradable composites formed by a polylactic acid matrix reinforced with 10%wt. magnesium microparticles were processed and their in vitro degradation investigated during 28 days. A joint analysis of the amount of H2 released, the changes in pH in buffered (PBS) and non-buffered media (distilled water), the variations in mass, microstructure and the mechanical performance of the specimens was developed. The main aim was to elucidate the relevance of Mg particles shape on tailoring the degradation kinetics of these novel composites. The results show that the shape of the Mg reinforcing particles plays a crucial role in the degradation rate of PLA/Mg composites, with spherical particles promoting a lower degradation rate than irregular particles. This fact is only partially due to the smaller surface area to volume ratio of the spherical particles. Irregular particles promote a faster formation of cracks and, therefore, an increasingly faster degradation of the polymeric matrix. In every case, the amount of H2 released by the composites was well below that released by monolithic Mg. The pH of PBS during degradation remained always within 7.2 and 7.4. PLA/Mg reinforced with spherical particles retains more than 90% of its mechanical properties after 7 days of immersion and more than 60% after 28 days. STATEMENT OF SIGNIFICANCE: The increasing demand for temporary orthopaedic implants is the driving force to seek new strategies to decrease costs and simultaneously improve patients comfort as well as simplify surgical procedures. Resorbable medical devices must be developed in order to have an appropriate degradation rate in agreement with the healing rate of bone. We are presenting for the first time results of the degradation kinetics of a new material based on polylactic acid reinforced with 10%wt. Mg microparticles. This work analyzes the relevance of Mg particle shape (irregular and spherical) on tailoring the degradation behaviour of these composites. Conclusions withdrawn from this study help to customize bioabsorbable materials in order to meet the requirements for a specific application and patient.

On the fatigue behavior of medical Ti6Al4V roughened by grit blasting and abrasiveless waterjet peening.

Flat fatigue specimens of biomedical Ti6Al4V ELI alloy were surface-processed by high pressure waterjet peening (WJP) without abrasive particles using moderate to severe conditions that yield roughness values in the range of those obtained by commercial grit blasting (BL) with alumina particles. Fatigue behavior of WJP and BL specimens was characterized under cyclical uniaxial tension tests (R=0.1). The emphasis was put on a comparative analysis of the surface and subsurface induced effects and in their relevance on fatigue behavior. Within the experimental setup of this investigation it resulted that blasting with alumina particles was less harmful for fatigue resistance than abrasiveless WJP. BL specimens resulted in higher subsurface hardening and compressive residual stresses. Specimens treated with more severe WJP parameters presented much higher mass loss and lower compressive residual stresses. From the analysis performed in this work, it follows that, in addition to roughness, waviness emerges as another important topographic parameter to be taken into account to try to predict fatigue behavior. It is envisaged that optimization of WJP parameters with the aim of reducing waviness and mass loss should lead to an improvement of fatigue resistance.

Quantitative assessment of the response of osteoblast- and macrophage-like cells to particles of Ni-free Fe-base alloys.

In the present study, the effect of mechanically alloyed particles of new FeAlCr alloys developed for potential applications as surgical implants has been tested on osteoblast- and macrophage-like cells and compared to particles of the Ti6Al4V alloy, for which there is a good clinical experience. After microstructural characterisation of the particles, cells were cultured with particles for 24-48 h using three different concentrations of particles, and the response of cells was quantified by assessment of viability, proliferation, and morphology. Mineralisation by osteoblasts was verified after 21 days. The amount of aluminium and chromium ions in the culture medium of macrophages was measured by graphite furnace atomic absorption and phagocytosis of particles assessed by light microscopy. Viability and proliferation of osteoblast- and macrophage-like cells were substantially unaffected by the presence of particles of the new alloys, which were phagocytosed according to their size. Aluminium and chromium ions were released in the culture medium, but no direct correlation with the cell behaviour was found. In vitro mineralisation was achieved by osteoblasts in due time. The new alloys are well tolerated in in vitro systems, and, due to their chemical and mechanical characteristics, they are under development for surgical implants.

Evaluation of mechanical properties and biological response of an alumina-forming Ni-free ferritic alloy.

PM 2000 is a Ni-free oxide dispersion strengthened Fe-20Cr-5Al alloy able to develop a fine, dense and tightly adherent alpha-alumina scale during high-temperature oxidation. Despite the high temperature involved during thermal oxidation (1100 degrees C), microstructural changes in the candidate material, a hot rolled product, hardly occurs. Consequently, the good mechanical properties of the as-received material are not significantly affected. Moreover, due to the high compressive residual stresses at the alumina scale, an increase in the fatigue limit from 500 to 530 MPa is observed. Such stresses also account for the high capability of the coating/metal system to withstand more than 1% tensile deformation without cracking. The biocompatibility of the alloy was assessed in comparison to commercial alumina. Saos-2 osteoblast-like cells were either challenged with PM 2000 particles, or seeded onto PM 2000 (with and without scale) solid samples. Viability, growth, and ALP release from cells were assessed after 3 or 7 days, while mineralization was checked at 18 days. This study has demonstrated that PM 2000 with and without scale are capable of supporting in vitro growth and function of osteoblast-like cells over a period of 18 days. Results from this study suggest that the resulting alumina/alloy system combines the good mechanical properties of the alloy with the superior biocompatibility of the alpha-alumina, for which there is very good clinical experience.

Dynamic nanomechanical properties of novel Si-rich intermetallic coatings growth on a medical 316 LVM steel by hot dipping in a hypereutectic Al-25Si alloy.

This aim of this study is to determine the elastoplastic properties of Ni-free Al3FeSi2 intermetallic coatings grown on medical stainless steel under different experimental conditions. Elastoplastic properties are defined by the plasticity index (PI), which correlates the hardness and the Young's modulus. Special emphasis is devoted to correlate the PI with the wear resistance under sliding contact, determined by scratch testing, and fracture toughness, determined by using a novel method based on successive impacts with small loads. With regard to the substrate, the developed coatings are harder and exhibit a lower Young's reduced modulus, irrespective of the experimental conditions. It has been shown that preheating of the samples prior to hot dipping and immersion influences the type and volume fraction of precipitates, which in turn also affect the nanomechanical properties. The higher the preheating temperature is, the greater the Young's reduced modulus is. For a given preheating condition, an increase of the immersion time yields a decrease in hardness. Although apparent friction coefficients of coated specimens are smaller than those obtained on AISI 316 LVM, they increase when using preheating or higher immersion times during processing, which correlates with the PI. The presence of precipitates produces an increase in fracture toughness, with values greater than those presented by samples processed on melted AlSi alloys with lower Si content (12 wt%). Therefore, these intermetallic coatings could be considered "hard but tough", suitable to enhance the wear resistance, especially when using short periods of immersion.

In vitro corrosion behaviour of MA 956 superalloy.

The need for appropriated metallic materials for long-term implants is nowadays the driving force for the development of alternative materials with improved corrosion resistance in body fluids. In this work the in vitro corrosion behaviour of MA 956 is evaluated by means of electrochemical techniques during long-term tests in simulated human body media. This alloy, after an isothermal treatment at 1100 degrees C, develops on the surface a fine, dense and adherent alpha-alumina scale which considerably enhances the good corrosion resistance of the non-treated alloy.

Electrochemical impedance spectroscopy of preoxidized MA 956 superalloy during in vitro experiments.

Preoxidation treatment of MA 956 superalloy at 1100 degrees C produces a fine and tightly adherent alpha-alumina layer at the surface, which provides the alloy with an excellent barrier against a great variety of aggressive environments. In this work the protective capacity of the alumina/alloy system is evaluated in a physiological medium by means of electrochemical impedance spectroscopy. The electrochemical response of the material is modelled by equivalent circuits which provide the most relevant corrosion and protection parameters applicable to MA 956 in both preoxidized and as-received conditions (passivated state). The high protective capacity of preoxidized MA 956 superalloy holds for long-term tests, which indicates that the corrosion phenomena, if any, would be characterized by very slow kinetics. The corrosion resistance of the preoxidized material is at least two orders of magnitude higher than that of the non-treated alloy.