Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 3 de 3
Filtrar
Más filtros

Banco de datos
Tipo del documento
Asunto de la revista
Intervalo de año de publicación
1.
J Mech Behav Biomed Mater ; 150: 106313, 2024 02.
Artículo en Inglés | MEDLINE | ID: mdl-38109815

RESUMEN

The aim is to investigate the impact of phase contents on mechanical properties, translucency, and aging stability of additively manufactured yttria partially stabilized zirconia ceramics. For that purpose, we evaluated two PSZ materials. The first type was prepared utilizing commercially available 5 mol% yttria-stabilized zirconia(5Y-PSZ), while the second type, denoted as 3Y+8Y-PSZ ceramics, was fabricated by blending 3 mol% and 8 mol% yttria-stabilized zirconia powders. Compared to 5Y-PSZ (39.90 wt% tetragonal phases and c/a2 = 1.0141), 3Y+8Y-PSZ is characterized by a greater abundance of tetragonal phases (47.68 wt%), which display higher tetragonality (c/a2 = 1.0165) and lower yttrium oxide content (2.25mol%). As a result, the 3Y+8Y-PSZ demonstrates elevated strength (816.52 MPa) and toughness (4.32 MPa m1/2), accompanied by reduced translucency(CR:0.47) and it exhibits greater susceptibility to aging. The phase contents, yttrium oxide content, and lattice parameters in the tetragonal phase play a crucial role in determining the mechanical properties, translucency, and aging stability of PSZ ceramics.


Asunto(s)
Estereolitografía , Itrio , Ensayo de Materiales , Circonio , Cerámica , Materiales Dentales , Propiedades de Superficie
2.
J Mech Behav Biomed Mater ; 144: 105952, 2023 08.
Artículo en Inglés | MEDLINE | ID: mdl-37311296

RESUMEN

A study was conducted to explore the potential of 5 mol% yttria-partially stabilized zirconia (5Y-PSZ) ceramics for dental restorations, using stereolithography (SLA) printing technique. Four different solid loadings were established in the ceramic paste systems to study their effects on microstructure, mechanical properties, and translucency. The study examined the rheological behavior and photopolymerization performance of the ceramic pastes with varying solid loadings. Results showed that, an increase in powder concentration resulted in a decrease in cure depth (Cd) and penetration depth (Dp). A narrower pore size distribution was observed in the green bodies with a high solid loading, facilitating the achievement of final densification. The green and sintered densities were highest at 52 vol%, with values of 3.46 ± 0.01 g/cm3 and 6.01 ± 0.02 g/cm3, respectively. Additionally, all of the green strengths exceeded 30 MPa, with a maximum of 35.09 ± 2.02 MPa obtained at 44 vol%. The maximum flexural strength and minimum contrast ratio (CR) value of 746 ± 75 MPa and 0.40 ± 0.01 were achieved at 52 vol% after sintering. No significant differences were observed in the phase composition and hardness of the as-sintered ceramics. Though significant differences were observed in photopolymerization performance, four materials showed similar structural reliability considering Weibull modulus and characteristic strength.


Asunto(s)
Estereolitografía , Circonio , Ensayo de Materiales , Reproducibilidad de los Resultados , Circonio/química , Cerámica/química , Itrio/química , Propiedades de Superficie , Materiales Dentales
3.
J Mech Behav Biomed Mater ; 148: 106211, 2023 12.
Artículo en Inglés | MEDLINE | ID: mdl-37935083

RESUMEN

The purpose of this study was to obtain dental ceramic materials with excellent mechanical properties and high resistance to low temperature degradation (LTD) via stereolithography (SLA) in combination with microwave sintering (MWS). The results have shown that the unaged MWS-1425 °C 3Y-TZP ceramics with uniform microstructure have high density up to 99.04% and excellent mechanical properties (Vickers hardness 14.07 GPa, fracture toughness 4.32 MPa m1/2, flexural strength 947.87 MPa). After 50 h of LTD, the m-phase content of MWS 3Y-TZP ceramics accounts for only 10.3%. In addition, the surface roughness increases by only 1.3 nm, the degraded depth is less than 5 µm, and the flexural strength exceeds 900 MPa. This exhibits the high resistance to LTD and excellent mechanical properties of dental 3Y-TZP ceramics can be obtained.


Asunto(s)
Microondas , Estereolitografía , Temperatura , Ensayo de Materiales , Circonio/química , Cerámica/química , Propiedades de Superficie , Itrio , Materiales Dentales
SELECCIÓN DE REFERENCIAS
DETALLE DE LA BÚSQUEDA