A Novel Scaffold of Icariin/Porous Magnesium Alloy-Repaired Knee Cartilage Defect in Rat by Wnt/ß-Catenin Signaling Pathway.

Cartilage defects caused by joint diseases are difficult to treat clinically. Tissue engineering materials provide a new means to promote the repair of cartilage defects. The purpose of this study is to design a novel scaffold of porous magnesium alloy loaded with icariin and sustained release in order to explore the effect and possible mechanism of this scaffold in repairing SD rat knee articular cartilage defect. We constructed a novel type of icariin/porous magnesium alloy scaffold, observed the structure of the scaffold by electron microscope, detected the drug release of icariin in the scaffold and the biological safety, and established an animal model of cartilage defect in the femoral intercondylar fossa of the knee joint in rats; the scaffold was placed in the defect. After 12 weeks of repair, the rat knee articular cartilage repair was evaluated by gross specimens and micro-CT, HE, safranin O-fast green, and toluidine blue staining combined with the modified Mankin's score. The protein expressions of the Wnt/ß-catenin signaling pathway-related factors (ß-catenin, Wnt5a, Wnt1, sFRP1) and chondrogenic differentiation-related factors (Sox9, Aggrecan, Col2α1) were detected by immunohistochemical staining. We found that the novel scaffold of icariin/porous magnesium alloy can release icariin slowly and has biosafety in rats. Compared with other groups, icariin/porous magnesium alloy can significantly promote the repair of cartilage defects and the expressions of ß-catenin, Wnt5a, Wnt1, Sox9, Aggrecan, and Col2α1 (P < 0.05). This novel scaffold can promote the repair of rat knee cartilage defects, and this process may be achieved by activating the Wnt/ß-catenin signaling pathway.

Biomimetic Porous Magnesium Alloy Scaffolds Promote the Repair of Osteoporotic Bone Defects in Rats through Activating the Wnt/ß-Catenin Signaling Pathway.

In this study, biomimetic porous magnesium alloy scaffolds were prepared to repair femoral bone defects in ovariectomized osteoporotic rats. The purpose of the study was to investigate the effect of biomimetic porous magnesium alloy scaffolds on repairing osteoporotic bone defects and possible mechanisms. The animal model of osteoporosis was established in female SD rats. Three months later, a bone defect of 3 mm in diameter and 3 mm in depth was created in the lateral condyle of the right femur. The rats were then randomly divided into two groups: an experimental group and a control group. Four weeks after surgery, gross specimens were observed and micro-CT scans were performed. The repair of osteoporotic femoral defects in rats was studied histologically using HE staining, Masson staining, and Goldner staining. The expression of Wnt5a, ß-catenin, and BMP-2 was measured between groups by immunohistochemical staining. The bone defect was repaired better after the application of biomimetic porous magnesium alloy scaffolds. Immunohistochemical results showed significantly higher expression of Wnt5a, ß-catenin, and BMP-2. To conclude, the biomimetic porous magnesium alloy scaffolds proposed in this paper might promote the repair of osteoporotic femoral bone defects in rats possibly through activating the Wnt/ß-catenin signaling pathway.

Fatigue and dynamic biodegradation behavior of additively manufactured Mg scaffolds.

Additive manufacturing (AM) has enabled the fabrication of biodegradable porous metals to satisfy the desired characteristics for orthopedic applications. The geometrical design on AM biodegradable metallic scaffolds has been found to offer a favorable opportunity to regulate their mechanical and degradation performance in previous studies, however mostly confined to static responses. In this study, we presented the effect of the geometrical design on the dynamic responses of AM Mg scaffolds for the first time. Three different types of porous structures, based on various unit cells (i.e., biomimetic, diamond, and sheet-based gyroid), were established and then subjected to selective laser melting (SLM) process using group-developed Mg-Nd-Zn-Zr alloy (JDBM) powders. The topology after dynamic electropolishing, dynamic compressive properties, and dynamic biodegradation behavior of the AM Mg scaffolds were comprehensively evaluated. It was found that dynamic electropolishing effectively removed the excessive adhered powders on the surfaces and resulted in similar geometrical deviations amongst the AM Mg scaffolds, independent of their porous structures. The geometrical design significantly affected the compressive fatigue properties of the AM Mg scaffolds, of which the sheeted-based gyroid structure demonstrated a superior fatigue endurance limit of 0.85 at 106 cycles. Furthermore, in vitro dynamic immersion behaviors of the AM Mg scaffolds revealed a decent dependence on local architectures, where the sheeted-based gyroid scaffold experienced the lowest structural loss with a relatively uniform degradation mode. The obtained results indicate that the geometrical design could provide a promising strategy to develop desirable bone substitutes for the treatment of critical-size load-bearing defects. STATEMENT OF SIGNIFICANCE: Additive manufacturing (AM) has provided unprecedented opportunities to fabricate geometrically complex biodegradable scaffolds where the topological design becomes a key determinant on comprehensive performance. In this paper, we fabricate 3 AM biodegradable Mg scaffolds (i.e., biomimetic, diamond, and sheet-based gyroid) and report the effect of the geometrical design on the dynamic responses of AM Mg scaffolds for the first time. The results revealed that the sheeted-based gyroid scaffold exhibited the best combination of superior compressive fatigue properties and relatively uniform dynamic biodegradation mode, suggesting that the regulation of the porous structures could be an effective approach for the optimization of AM Mg scaffolds as to satisfy clinical requirements in orthopedic applications.

A Biomimetic Zinc Alloy Scaffold Coated with Brushite for Enhanced Cranial Bone Regeneration.

Bone tissue engineering is considered as a promising pathway for bone regeneration and defect reconstruction, in which scaffolds play an important role. Zn alloy, which is a biodegradable metal material that has advantages of metallic and biodegradable characteristics, has its special features, especially the ideal degradation rate and acceptable biocompatibility, which make it worthy to be further investigated for medical applications. In this study, new biodegradable porous Zn alloy scaffolds with Ca-P coating were attempted to repair cranial bone defect, and in vitro and in vivo assays were conducted to evaluate its biocompatibility, osteo-inductivity, and osteo-conductivity. The results indicated that coated Zn alloy possessed good biocompatibility, with no cytotoxicity. It could also promote osteogenic differentiation and calcium deposition of rabbit BMSCs in vitro, and new bone formation around the scaffold in vivo. The biodegradable porous Zn alloy scaffold with Ca-P coating is considered to be promising in cranial bone defect repair.

Simultaneous enhancement of anti-corrosion, biocompatibility, and antimicrobial activities by hierarchically-structured brushite/Ag3PO4-coated Mg-based scaffolds.

Development of bone graft substitutes with appropriate integration of mechanical, biodegradable, and biofunctional properties, which promote bone formation while simultaneously preventing implant-associated infections, remains a great challenge. Herein we designed and synthesized a brushite/Ag3PO4-coated Mg-Nd-Zn-Zr scaffolds through chemical solution deposition of a composite coating onto the fluorinated Mg-based scaffolds generated with template replication method. The coated Mg-based open-porous scaffolds exhibit hierarchically-structured surface with cube-shaped Ag3PO4 nanoparticles uniformly distributed on top of microsized brushite grains. Immersion test reveals that the initial degradation rate of the coated scaffolds could be reduced by ~81% compared to the original scaffolds. The mean corrosion rate in 4 weeks falls into 0.10-0.15 mm/year to meet clinical requirements. The compatibility and ALP activity of cells grown in the extracts from the coated Mg-based scaffolds were increased compared with Ti control and original scaffolds, mainly due to the favorable microenvironment generated by Mg biodegradation. Besides, the coated Mg-based scaffold demonstrated potent antimicrobial activity via the synergistic actions of alkaline degradation products of Mg and the Ag species in the coating, achieving >99.5% antibacterial rate against both gram-positive and gram-negative bacteria with relatively low silver content. Taken together, this study presents a new candidate of brushite/Ag3PO4-coated Mg-based scaffold with appropriate degradation characteristics, cytocompatibility, and antimicrobial activities for bone tissue engineering applications.

The bioeffects of degradable products derived from a biodegradable Mg-based alloy in macrophages via heterophagy.

Biodegradable magnesium alloys are promising candidates for use in biomedical applications. However, degradable particles (DPs) derived from Mg-based alloys have been observed in tissue in proximity to sites of implantation, which might result in unexpected effects. Although previous in vitro studies have found that macrophages can take up DPs, little is known about the potential phagocytic pathway and the mechanism that processes DPs in cells. Additionally, it is necessary to estimate the potential bioeffects of DPs on macrophages. Thus, in this study, DPs were generated from a Mg-2.1Nd-0.2Zn-0.5Zr alloy (JDBM) by an electrochemical method, and then macrophages were incubated with the DPs to reveal the potential impact. The results showed that the cell viability of macrophages decreased in a concentration-dependent manner in the presence of DPs due to effects of an apoptotic pathway. However, the DPs were phagocytosed into the cytoplasm of macrophages and further degraded in phagolysosomes, which comprised lysosomes and phagosomes, by heterophagy instead of autophagy. Furthermore, several pro-inflammatory cytokines in macrophages were upregulated by DPs through the induction of reactive oxygen species (ROS) production. To the best of our knowledge, this is the first study to show that DPs derived from a Mg-based alloy are consistently degraded in phagolysosomes after phagocytosis by macrophages via heterophagy, which results in an inflammatory response owing to ROS overproduction. Thus, our research has increased the knowledge of the metabolism of biodegradable Mg metal, which will contribute to an understanding of the health effects of biodegradable magnesium metal implants used for tissue repair. STATEMENT OF SIGNIFICANCE: Biomedical degradable Mg-based alloys have great promise in applied medicine. Although previous studies have found that macrophages can uptake degradable particles (DPs) in vitro and observed in the sites of implantation in vivoin vivo, few studies have been carried out on the potential bioeffects relationship between DPs and macrophages. In this study, we analyzed the bioeffects of DPs derived from a Mg-based alloy on the macrophages. We illustrated that the DPs were size-dependently engulfed by macrophages via heterophagy and further degraded in the phagolysosome rather than autophagosome. Furthermore, DPs were able to induce a slight inflammatory response in macrophages by inducing ROS production. Thus, our research enhances the knowledge of the interaction between DPs of Mg-based alloy and cells, and offers a new perspective regarding the use of biodegradable alloys.

Effects of extrusion temperature on microstructure, mechanical properties and in vitro degradation behavior of biodegradable Zn-3Cu-0.5Fe alloy.

Zn-based alloys as biodegradable materials for cardiovascular stents have drawn more and more attention in recent years. However, the hot plastic deformation of Zn-based alloys does not get enough attention. In this study, Zn-3Cu-0.5Fe alloy was prepared and then hot extruded at 140, 180, 220 and 260 °C. Effects of extrusion temperature on the microstructure, mechanical properties and degradation behavior were investigated. Nano-scaled particles precipitated during extrusion and the quantity decreased with the increasing of extrusion temperature. As the extrusion temperature increased from 140 to 260 °C, the grain size increased from 1.15 to 4.38 µm, the yield strength and ultimate tensile strength increased from 203 ±â€¯3.23 and 221 ±â€¯1.56 MPa to 269 ±â€¯2.65 and 302 ±â€¯8.01 MPa, increased by 32.5% and 45%, while the degradation rate was decreased gradually from 62.8 ±â€¯0.72 µm/year to 49.9 ±â€¯3.35 µm/year, decreased by 20.5%. In addition, the degradation behavior changes from a relatively uniform degradation mode to a localized degradation mode with the increase of the grain size. Dislocation gliding is replaced by grain-boundary movement and dynamic recrystallization (DRX) in the room temperature tensile deformation process. Lower extrusion temperature is beneficial for higher elongation and degradation rate as well as relatively uniform degradation mode, which is better suitable for the clinical application of cardiovascular stents.

Macrophage phagocytosis of biomedical Mg alloy degradation products prepared by electrochemical method.

Biomedical Mg alloy is promising for its widespread use clinically. In vitro and in vivo studies showed that the degradation products of biomedical Mg alloy were composed of O, P, Ca, Mg and other alloying elements. However, little is known about the metabolism of the degradation products. In this study, the in vitro macrophage phagocytosis of the degradation products of a biomedical Mg-Nd-Zn-Zr alloy was directly observed. This result affirms the necessity to investigate the long-term fate of Mg alloy degradation products in physiological environments. Besides, an electrochemical method was proposed to prepare enough amount of degradation products in vitro efficiently.

Effect of macrophages on in vitro corrosion behavior of magnesium alloy.

The influence of cells on the corrosion behavior of biomedical magnesium alloy is an important but less studied topic, which is helpful for understanding the inconsistent corrosion rates between in vitro and in vivo experiments. In this work, macrophages were directly cultured on Mg-2.1Nd-0.2Zn-0.5Zr (wt %, abbreviated as JDBM) alloy surface for 72 or 168 hours. Macrophages retained good viability and the generation of reactive oxygen species (ROS) was greatly promoted on the alloy. Weight loss, Mg(2+) concentration, and cross-section observation results demonstrated that macrophages accelerated the in vitro corrosion of JDBM. The coverage of cell body did not affect the local thickness of corrosion product layer. The corrosion product layer had a porous inner Mg(OH)2 layer and a dense outer layer mainly composed of O, P, Mg, and Ca. The uniform acceleration of JDBM corrosion was attributed to the omnidirection diffusion of ROS from macrophages. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2476-2487, 2016.