RESUMEN
Mature elastin synthesis is a key challenge in arterial tissue engineering. Most engineered vessels lack elastic fibers in the medial layer and those present are poorly organized. The objective of this study is to increase mature elastin synthesis in small-diameter arterial constructs. Adult primary baboon smooth muscle cells (SMCs) were seeded in the lumen of porous tubular scaffolds fabricated from a biodegradable elastomer, poly(glycerol sebacate) (PGS) and cultured in a pulsatile flow bioreactor for 3 wk. We tested the effect of pore sizes on construct properties by histological, biochemical, and mechanical evaluations. Histological analysis revealed circumferentially organized extracellular matrix proteins including elastin and the presence of multilayered SMCs expressing calponin and α-smooth muscle actin. Biochemical analysis demonstrated that the constructs contained mature elastin equivalent to 19% of the native arteries. Mechanical tests indicated that the constructs could withstand up to 200 mmHg burst pressure and exhibited compliance comparable to native arteries. These results show that nontransfected cells in PGS scaffolds in unsupplemented medium produced a substantial amount of mature elastin within 3 wk and the elastic fibers had similar orientation as those in native arteries. The 25-32 µm pore size supported cell organization and elastin synthesis more than larger pore sizes. To our knowledge, there was no prior report of the synthesis of mature and organized elastin in arterial constructs without exogenous factors or viral transduction.
Asunto(s)
Arterias/anatomía & histología , Reactores Biológicos , Elastina/biosíntesis , Miocitos del Músculo Liso/metabolismo , Ingeniería de Tejidos/métodos , Animales , Arterias/metabolismo , Decanoatos , Elastina/metabolismo , Técnica del Anticuerpo Fluorescente , Glicerol/análogos & derivados , Ensayo de Materiales , Microscopía Electrónica de Rastreo , Papio , Polímeros , Medicina Regenerativa/métodos , Microtomografía por Rayos XRESUMEN
Zn-based biomaterials have emerged as promising new types of bioresorbable metallics applicable to orthopedic devices, cardiovascular stents, and other medical applications recently. Compared to other degradable metallic biomaterials (i.e., Mg- or Fe-based), Zn biomaterials have a more appropriate corrosion rate without hydrogen gas evolution. Here, we evaluated the potential of Zn-based metallics as medical implants, both in vitro and in vivo, alongside a standard benchmark Mg alloy, AZ31. The mechanical properties of the pure Zn were not strong enough but were significantly enhanced (microhardness > 70 kg/mm2, strength > 220 MPa, elongation > 15%) after alloying with Sr or Mg (1.5 at. %), surpassing the minimal design criteria for load-bearing device applications. The corrosion rate of Zn-based biomaterials was about 0.4 mm/year, significantly slower than that of AZ31. The measured cell viability and proliferation of three different human primary cells fared better for Zn-based biomaterials than AZ31 using both direct and indirect culture methods. Platelet adhesion and activation on Zn-based materials were minimal, significantly less than on AZ31. The hemolysis ratio of red cells (<0.5%) after incubation with Zn-based materials was also well below the ISO standard of 5%. Moreover, Zn-based biomaterials promoted stem cell differentiation to induce the extracellular matrix mineralization process. In addition, in vivo animal testing using subcutaneous, bone, and vascular implantations revealed that the acute toxicity and immune response of Zn-based biomaterials were minimal/moderate, comparable to that of AZ31. No extensive cell death and foreign body reactions were observed. Taken together, Zn-based biomaterials may have a great potential as promising candidates for medical implants.
Asunto(s)
Aleaciones , Materiales Biocompatibles , Proliferación Celular/efectos de los fármacos , Ensayo de Materiales , Zinc , Aleaciones/química , Aleaciones/farmacocinética , Aleaciones/farmacología , Animales , Materiales Biocompatibles/química , Materiales Biocompatibles/farmacocinética , Materiales Biocompatibles/farmacología , Línea Celular , Supervivencia Celular/efectos de los fármacos , Corrosión , Humanos , Ratones , Zinc/química , Zinc/farmacocinética , Zinc/farmacologíaRESUMEN
A series of crosslinkable nanocomposites has been developed using hydroxyapatite (HA) nanoparticles and poly(propylene fumarate) (PPF). PPF/HA nanocomposites with four different weight fractions of HA nanoparticles have been characterized in terms of thermal and mechanical properties. To assess surface chemistry of crosslinked PPF/HA nanocomposites, their hydrophilicity and capability of adsorbing proteins have been determined using static contact angle measurement and MicroBCA protein assay kit after incubation with 10% fetal bovine serum (FBS), respectively. In vitro cell studies have been performed using MC3T3-E1 mouse pre-osteoblast cells to investigate the ability of PPF/HA nanocomposites to support cell attachment, spreading, and proliferation after 1, 4, and 7 days. By adding HA nanoparticles to PPF, the mechanical properties of crosslinked PPF/HA nanocomposites have not been increased due to the initially high modulus of crosslinked PPF. However, hydrophilicity and serum protein adsorption on the surface of nanocomposites have been significantly increased, resulting in enhanced cell attachment, spreading, and proliferation after 4 days of cell seeding. These results indicate that crosslinkable PPF/HA nanocomposites are useful for hard tissue replacement because of excellent mechanical strength and osteoconductivity.
Asunto(s)
Reactivos de Enlaces Cruzados/química , Durapatita/química , Fumaratos/química , Nanocompuestos , Polipropilenos/química , Células 3T3 , Animales , Adhesión Celular , Proliferación Celular , Ratones , Microscopía Electrónica de Rastreo , Microscopía Electrónica de TransmisiónRESUMEN
Novel biodegradable poly(ethylene glycol) (PEG) based hydrogels, namely, PEG sebacate diacrylate (PEGSDA) were synthesized, and their properties were evaluated. Chemical structures of these polymers were confirmed by Fourier transform infrared and proton nuclear magnetic resonance (1H NMR) spectroscopy. After photopolymerization, the dynamic shear modulus of the hydrogels was up to 0.2 MPa for 50% PEGSDA hydrogel, significantly higher than conventional hydrogels such as PEG diacrylate (PEGDA). The swelling ratios of these macromers were significantly lower than PEGDA. The in vitro degradation study demonstrated that these hydrogels were biodegradable with weight losses about 66% and 32% for 25% and 50% PEGSDA after 8 weeks of incubation in phosphate-buffered saline at 37 degrees C. In vitro biocompatibility was assessed using cultured rat bone marrow stromal cells (MSCs) in the presence of unreacted monomers or degradation products. Unlike conventional PEGDA hydrogels, PEGSDA hydrogel without RGD peptide modification induced MSC cell adhesion similar to tissue culture polystyrene. Finally, complex three-dimensional structures of PEGSDA hydrogels using solid free form technique were fabricated and their structure integrity was better maintained than PEGDA hydrogels. These hydrogels may find use as scaffolds for tissue engineering applications.
Asunto(s)
Ácidos Decanoicos/química , Ácidos Dicarboxílicos/química , Hidrogeles/química , Hidrogeles/síntesis química , Polietilenglicoles/química , Ingeniería de Tejidos , Animales , Células Cultivadas , Espectroscopía de Resonancia Magnética , Masculino , Estructura Molecular , Ratas , Ratas Sprague-Dawley , Espectroscopía Infrarroja por Transformada de FourierRESUMEN
The biodegradable elastomeric polyester poly(glycerol sebacate) (PGS) was developed for soft-tissue engineering. It has been used in various research applications such as wound healing, cartilage tissue engineering, and vascular grafting due to its biocompatibility and elastomeric properties. However conventional PGS manufacture is generally limited by the laborious reaction conditions needed for curing which requires elevated reaction temperatures, high vacuum and multi-day reaction times. In this study, we developed a microwave irradiation methodology to fabricate PGS scaffolds under milder conditions with curing times that are 8 times faster than conventional methods. In particular, we determined microwave reaction temperatures and times for maximum crosslinking of PGS elastomers, demonstrating that PGS is fully crosslinked using gradual heating up to 160 °C for 3 h. Porosity and mechanical properties of these microwave-cured PGS elastomers were shown to be similar to PGS elastomers fabricated by the conventional polycondensation method (150 °C under 30 Torr for 24 h). To move one step closer to clinical application, we also examined the biocompatibility of microwave-cured PGS using in vitro cell viability assays with primary baboon arterial smooth muscle cells (SMCs). These combined results show microwave curing of PGS is a viable alternative to conventional curing.
Asunto(s)
Decanoatos/farmacología , Glicerol/análogos & derivados , Microondas , Polímeros/farmacología , Animales , Supervivencia Celular/efectos de los fármacos , Decanoatos/química , Glicerol/química , Glicerol/farmacología , Masculino , Ensayo de Materiales , Fenómenos Mecánicos , Músculo Liso Vascular/citología , Papio , Polímeros/química , Porosidad , Andamios del Tejido/química , Injerto VascularRESUMEN
Autologous veins are the most widely used grafts for bypassing small arteries in coronary and peripheral arterial occlusive diseases. However, they have limited availability and cause donor-site morbidity. Here, we report a direct comparison of acellular biodegradable synthetic grafts and autologous veins as interposition grafts of rat carotid arteries, which is a good model for clinically relevant small arteries. Notably, extensive but transient infiltration of circulating monocytes at day 14 in synthetic grafts leads to a quickly-resolved inflammation and arterial-like tissue remodeling. The vein graft exhibits a similar inflammation phase except the prolonged presence of inflammatory monocytes. The walls of the remodeled synthetic graft contain many circumferentially aligned contractile non-proliferative smooth muscle cells (SMCs), collagen and elastin. In contrast, the walls of the vein grafts contain disorganized proliferating SMCs and thicken over time, suggesting the onset of stenosis. At 3 months, both grafts have a similar patency, extracellular matrix composition, and mechanical properties. Furthermore, synthetic grafts exhibit recruitment and re-orientation of newly synthesized collagen fibers upon mechanical loading. To our knowledge, this is the first demonstration of a biodegradable synthetic vascular graft with a performance similar to an autologous vein in small artery grafting.
Asunto(s)
Prótesis Vascular , Arterias Carótidas/cirugía , Decanoatos/química , Glicerol/análogos & derivados , Polímeros/química , Animales , Colágeno/química , Matriz Extracelular/química , Glicerol/química , Masculino , Músculo Liso Vascular/citología , Miocitos del Músculo Liso/citología , Ratas , Ingeniería de Tejidos/métodosRESUMEN
Poly(propylene fumarate) (PPF) is an injectable, biodegradable polymer that has been used for fabricating preformed scaffolds in tissue engineering applications because of in situ crosslinking characteristics. Aiming for understanding the effects of pore structure parameters on bone tissue ingrowth, 3-dimensional (3D) PPF scaffolds with controlled pore architecture have been produced in this study from computer-aided design (CAD) models. We have created original scaffold models with 3 pore sizes (300, 600, and 900 microm) and randomly closed 0%, 10%, 20%, or 30% of total pores from the original models in 3 planes. PPF scaffolds were fabricated by a series steps involving 3D printing of support/build constructs, dissolving build materials, injecting PPF, and dissolving support materials. To investigate the effects of controlled pore size and interconnectivity on scaffolds, we compared the porosities between the models and PPF scaffolds fabricated thereby, examined pore morphologies in surface and cross-section using scanning electron microscopy, and measured permeability using the falling head conductivity test. The thermal properties of the resulting scaffolds as well as uncrosslinked PPF were determined by differential scanning calorimetry and thermogravimetric analysis. Average pore sizes and pore shapes of PPF scaffolds with 600- and 900-microm pores were similar to those of CAD models, but they depended on directions in those with 300-microm pores. Porosity and permeability of PPF scaffolds decreased as the number of closed pores in original models increased, particularly when the pore size was 300 microm as the result of low porosity and pore occlusion. These results show that 3D printing and injection molding technique can be applied to crosslinkable polymers to fabricate 3D porous scaffolds with controlled pore structures, porosity, and permeability using their CAD models.
Asunto(s)
Materiales Biocompatibles/síntesis química , Diseño Asistido por Computadora , Fumaratos/síntesis química , Modelos Químicos , Polipropilenos/síntesis química , Ingeniería de Tejidos/métodos , Simulación por Computador , Ensayo de Materiales , Porosidad , Propiedades de Superficie , Ingeniería de Tejidos/instrumentaciónRESUMEN
The selection criteria for potential bone engineering scaffolds are based chiefly on their relative mechanical comparability to mature bone. In this study, we challenge this notion by obtaining full regeneration of a rabbit ulna critical size defect by employing the elastomeric polymer, poly(glycerol sebacate) (PGS). We tested the regeneration facilitated by PGS alone, PGS in combination with hydroxyapatite particles, or PGS seeded with bone marrow stromal cells. We investigated the quantity and quality of the regenerated bone histologically, by microcomputed tomography and by four-point bending flexural mechanical testing at 8 weeks postimplantation. We conclude that the relatively lower stiffness of this biocompatible elastomer allows a load-transducing milieu in which osteogenesis, matrix deposition, and eventual bone maturation can take place. This study's results suggest that PGS elastomer is an auspicious osteoconductive material for the regeneration of bony defects. These results call for an innovative reassessment of the current art of selection for novel bone scaffold materials.
Asunto(s)
Materiales Biocompatibles , Regeneración Ósea , Decanoatos , Elastómeros , Glicerol/análogos & derivados , Ensayo de Materiales , Polímeros , Andamios del Tejido/química , Animales , Huesos/diagnóstico por imagen , Huesos/efectos de los fármacos , Huesos/fisiología , Conejos , Microtomografía por Rayos XRESUMEN
Host cell recruitment is crucial for vascular graft remodeling and integration into the native blood vessel; it is especially important for cell-free strategies which rely on host remodeling. Controlled release of growth factors from vascular grafts may enhance host cell recruitment. Stromal cell-derived factor (SDF)-1α has been shown to induce host progenitor cell migration and recruitment; however, its potential in regenerative therapies is often limited due to its short half-life in vivo. This report describes a coacervate drug delivery system for enhancing progenitor cell recruitment into an elastomeric vascular graft by conferring protection of SDF-1α. Heparin and a synthetic polycation are used to form a coacervate, which is incorporated into poly(glycerol sebacate) (PGS) scaffolds. In addition to protecting SDF-1α, the coacervate facilitates uniform scaffold coating. Coacervate-laden scaffolds have high SDF-1α loading efficiency and provide sustained release under static and physiologically-relevant flow conditions with minimal initial burst release. In vitro assays showed that coacervate-laden scaffolds enhance migration and infiltration of human endothelial and mesenchymal progenitor cells by maintaining a stable SDF-1α gradient. These results suggest that SDF-1α coacervate-laden scaffolds show great promise for in situ vascular regeneration.
Asunto(s)
Quimiocina CXCL12/metabolismo , Células Madre/citología , Células Madre/metabolismo , Movimiento Celular/fisiología , Células Cultivadas , Quimiocina CXCL12/genética , Decanoatos/química , Glicerol/análogos & derivados , Glicerol/química , Humanos , Células Madre Mesenquimatosas/citología , Células Madre Mesenquimatosas/metabolismo , Polímeros/química , Ingeniería de Tejidos/métodos , Andamios del Tejido/químicaRESUMEN
The evaluation of candidate materials and designs for soft tissue scaffolds would benefit from the ability to monitor the mechanical remodeling of the implant site without the need for periodic animal sacrifice and explant analysis. Toward this end, the ability of non-invasive ultrasound elasticity imaging (UEI) to assess temporal mechanical property changes in three different types of porous, biodegradable polyurethane scaffolds was evaluated in a rat abdominal wall repair model. The polymers utilized were salt-leached scaffolds of poly(carbonate urethane) urea, poly(ester urethane) urea and poly(ether ester urethane) urea at 85% porosity. A total of 60 scaffolds (20 each type) were implanted in a full thickness muscle wall replacement in the abdomens of 30 rats. The constructs were ultrasonically scanned every 2 weeks and harvested at weeks 4, 8 and 12 for compression testing or histological analysis. UEI demonstrated different temporal stiffness trends among the different scaffold types, while the stiffness of the surrounding native tissue remained unchanged. The changes in average normalized strains developed in the constructs from UEI compared well with the changes of mean compliance from compression tests and histology. The average normalized strains and the compliance for the same sample exhibited a strong linear relationship. The ability of UEI to identify herniation and to characterize the distribution of local tissue in-growth with high resolution was also investigated. In summary, the reported data indicate that UEI may allow tissue engineers to sequentially evaluate the progress of tissue construct mechanical behavior in vivo and in some cases may reduce the need for interim time point animal sacrifice.
Asunto(s)
Procesamiento de Imagen Asistido por Computador/instrumentación , Poliésteres/química , Poliuretanos/química , Ingeniería de Tejidos/métodos , Ultrasonido/instrumentación , Animales , Materiales Biocompatibles/química , Colágeno/química , Elasticidad , Femenino , Procesamiento de Imagen Asistido por Computador/métodos , Modelos Animales , Porosidad , Ratas , Ratas Endogámicas Lew , Andamios del Tejido/química , Ultrasonido/métodosRESUMEN
Cardiovascular disease is one of the leading cause of mortality in the US and especially, coronary artery disease increases with an aging population and increasing obesity. Currently, bypass surgery using autologous vessels, allografts, and synthetic grafts are known as a commonly used for arterial substitutes. However, these grafts have limited applications when an inner diameter of arteries is less than 6 mm due to low availability, thrombotic complications, compliance mismatch, and late intimal hyperplasia. To overcome these limitations, tissue engineering has been successfully applied as a promising alternative to develop small-diameter arterial constructs that are nonthrombogenic, robust, and compliant. Several previous studies have developed small-diameter arterial constructs with tri-lamellar structure, excellent mechanical properties and burst pressure comparable to native arteries. While high tensile strength and burst pressure by increasing collagen production from a rigid material or cell sheet scaffold, these constructs still had low elastin production and compliance, which is a major problem to cause graft failure after implantation. Considering these issues, we hypothesized that an elastometric biomaterial combined with mechanical conditioning would provide elasticity and conduct mechanical signals more efficiently to vascular cells, which increase extracellular matrix production and support cellular orientation. The objective of this report is to introduce a fabrication technique of porous tubular scaffolds and a dynamic mechanical conditioning for applying them to arterial tissue engineering. We used a biodegradable elastomer, poly (glycerol sebacate) (PGS) for fabricating porous tubular scaffolds from the salt fusion method. Adult primary baboon smooth muscle cells (SMCs) were seeded on the lumen of scaffolds, which cultured in our designed pulsatile flow bioreactor for 3 weeks. PGS scaffolds had consistent thickness and randomly distributed macro- and micro-pores. Mechanical conditioning from pulsatile flow bioreactor supported SMC orientation and enhanced ECM production in scaffolds. These results suggest that elastomeric scaffolds and mechanical conditioning of bioreactor culture may be a promising method for arterial tissue engineering.
Asunto(s)
Arterias/crecimiento & desarrollo , Decanoatos , Elastómeros , Glicerol/análogos & derivados , Músculo Liso Vascular/crecimiento & desarrollo , Polímeros , Ingeniería de Tejidos/instrumentación , Ingeniería de Tejidos/métodos , Andamios del Tejido , Animales , Arterias/citología , Reactores Biológicos , Prótesis Vascular , Masculino , Músculo Liso Vascular/citología , PapioRESUMEN
Stereolithography using photo-cross-linkable polymeric biomaterials is an effective technique for fabricating highly complex three-dimensional (3D) scaffolds with controlled microstructures for tissue engineering applications. In this study, we have optimized the UV curable polymer solution composition and laser parameters for the stereolithography machine. Poly(propylene fumarate) (PPF) was used as the biomaterial, diethyl fumarate (DEF) was used as the solvent, and bisacrylphosphrine oxide (BAPO) was used as the photoinitiator. Three different weight ratios of PPF/DEF and BAPO contents were characterized by measuring the viscosities and thermal properties of the un-cross-linked solutions and the mechanical properties of the formed scaffolds. After optimizing the resin composition by satisfying both the viscosity limitation and the mechanical requirement, laser parameters such as critical exposure (Ec) and penetration depth (Dp) were determined from the working curve and the relationship between laser speed and energy by measuring the thickness of predesigned windows fabricated in stereolithography with different ranges of Ec and Dp. Three-dimensional scaffolds with various pore sizes, pore shapes, and porosities were designed in computer-aided design (CAD) software and were fabricated in stereolithography. The fabricated scaffolds were characterized by measuring external dimensions, porosities, mean pore sizes, and compressive moduli and were compared to the CAD models. Feature accuracy in the xy-plane was achieved and overcuring of the resin in z-axis was minimized. The stereolithographically fabricated scaffolds with controlled microstructures can be useful in diverse tissue engineering applications.