Radiographic analysis of PEEK cage and FRA in adult spinal deformity fused to sacrum.

STUDY DESIGN: Retrospective radiographic study. OBJECTIVE: To radiographically evaluate sagittal plane profile and fusion rates of polyetheretherketone (PEEK) cages versus femoral ring allografts (FRAs) in patients with adult spinal deformity fused to the sacrum. SUMMARY OF BACKGROUND DATA: FRAs have been widely used in various degenerative lumbar spine disorders and in adult deformity to achieve interbody fusions with promising results. PEEK cages have gained increasing popularity of late; however, there is little documentation to the radiographic comparisons between PEEK cages and FRAs used in patients with adult spine deformity treated with long fusions to the sacrum. METHODS: From March 2006 to February 2010, we analyzed 48 patients (mean age, 56.3±13.9 y) of 61 consecutive adult patients with global coronal and sagittal adult spine deformities who underwent first stage ALIF using PEEK cages or FRAs at L4-L5, L5-S1 segments followed by long (>6 levels) posterior instrumentation. PEEK cages and FRAs were used randomly according to surgeon's preference. Two independent observers retrospectively evaluated preoperative and postoperative disk height, foraminal height, segmental lordosis, and the interbody fusion rates at different postoperative intervals. RESULTS: Both PEEK cages and FRAs significantly (P<0.05) maintained disk space height at all follow-up times. PEEK cages maintained foraminal height and segmental lordosis, especially at L4-L5 better than FRAs at the final follow-up. At the final follow-up, PEEK cages achieved 94.9% of fusion rate, which was significantly (P<0.05) superior to FRA (84.2%), and PEEK cages were superior to FRAs in attaining earlier solid fusion. The Prolo functional scores of FRAs or/and PEEK cages were significantly improved at the final follow-up and did not show a significant difference between them. CONCLUSIONS: Both PEEK cages and FRAs can significantly increase disk space height and achieve similar clinical outcomes in treating adult spinal deformity fused to the sacrum. The radiographic results of PEEK cages were superior to FRAs in terms of an earlier solid fusion, and greater restoration of segmental lordosis.

A Technique for the In Vivo Study of Three-dimensional Cervical Segmental Motion Characteristics After Anterior Screw Fixation for Odontoid Process Fractures.

STUDY DESIGN: Kinematics of the cervical spine was investigated using cone beam computed tomography (CBCT) images combined with three dimensions to three dimensions (3D-3D) registration technology in patients after anterior odontoid screw fixation (AOSF) surgery. OBJECTIVE: The aim of this study was to investigate in vivo 3D cervical motion characteristics of patients who had undergone AOSF surgeries. SUMMARY OF BACKGROUND DATA: AOSF surgery is a classic surgical method for the treatment of odontoid fracture, but there are few studies that investigated its effect on in vivo biomechanics of the cervical spine. Postoperative biomechanical characters of the atlantoaxial joint (C1-C2) and the caudal adjacent segment (C2-C3) have yet to be clarified. METHODS: The study involved 14 patients subjected to a procedure of AOSF with lag screw. Subjects were matched with 14 healthy controls. All subjects underwent CBCT scanning of the cervical spine under seven functional positions. A 3D-3D registration was performed for each vertebra at each functional position to calculate the segmental motion characteristics. The ranges of motion (ROMs) of the C1-C2, C2-C3, and the overall cervical spine (C1-C7) for each of the functional positions were determined. RESULTS: The ROMs of the AOSF group were significantly (P < 0.05) smaller than the control group in flexion-extension positions for the C1-C2 (7.0°vs.11.0°), C2-C3 (3.7°vs.6.7°) and C1-C7 (43.3°vs.54.4°). The twisting ROM of the C1-C2 was 39.3° in the AOSF group and 65.7° in the control (P < 0.05), the bending ROM of the C2-C3 was 2.8° in the AOSF group and 8.9° in the control (P < 0.05). The twisting ROM of C1-C7 segment was 63.2° for the AOSF and 98.1° for the healthy control groups (P < 0.05). CONCLUSION: Although AOSF surgery reduced the flexion-extension ROMs of all investigated spinal segments, additionally, it reduced twisting ROMs of C1-C2 and C1-C7, but only lateral bending ROM of C2-C3, when compared with the control group. The data implied that the AOSF surgery would result in different biomechanics changes in the atlantoaxial segment and caudal adjacent segment. Longer-term follow-up studies of larger patient cohorts are necessary to evaluate the clinical outcomes of patients after the AOSF surgery.Level of Evidence: 3.

The effect of structural parameters of total hip arthroplasty on polyethylene liner wear behavior: A theoretical model analysis.

Using large femoral heads in total hip arthroplasty (THA) has been widely advocated to improve the function and longevity of the components. However, increasing the head size has been shown to accelerate polyethylene liner wear. Few studies have investigated the effect of other important structural parameters (such as polyethylene liner thickness, metal cup size, head-liner conformity, loading conditions, etc.) on the biomechanical functions of the THAs. In this study, an analytical model was used to evaluate the polyethylene liner wear characteristics of the THAs (defined using a biomechanical wear factor) with various structural parameters of the THAs and loading conditions. For all the THA systems examined in this study, under the same loading conditions, a larger head leads to increasing contact areas, lower contact stresses, and higher biomechanical wear factors. When the head size is fixed, a decrease in the polyethylene liner thickness or a decrease in the head-liner conformity leads to higher peak contact stresses and smaller contact areas and consequently, lower biomechanical wear factors. This study provides a parametric analysis tool for the optimal design/selection of the THA systems and for prediction of early effects of various structural parameters on the biomechanical function (such as contact stresses) and longevity (such as polyethylene liner wear) of the THA systems.

Structural stability of a polyetheretherketone femoral component-A 3D finite element simulation.

BACKGROUND: Because its mechanical properties are similar to cortical bones of the knee, polyetheretherketone (PEEK) material has been used to make total knee arthroplasty (TKA) components. This study investigated the PEEK femoral component deformation of a TKA system and compared the data with that of a cobalt-chromium (CoCr) component. METHODS: A 3D finite element knee model was constructed using CT images of a normal subject. A knee prosthesis was installed on the model to simulate a TKA knee. The material properties of the bone were assumed linear and transverse isotropic. The femoral component was modeled using a PEEK or CoCr material. A compressive load was applied to the knee at full extension. Tibiofemoral contact stresses and femoral component deformations were analyzed. FINDINGS: Under a 3 kN load, the maximal Von-Mises stresses in the femoral component were 14.39 MPa and 30.05 MPa for the PEEK and CoCr components, respectively. At the tibial polyethylene surface, the CoCr femoral component caused higher contact stresses (>2.2%) than the PEEK component. The deformation of the PEEK component was over 3 times larger than that of the CoCr component (0.65 × 10-3 mm vs 0.2 × 10-3 mm). INTERPRETATION: The PEEK femoral component could result in lower contact stresses, but larger deformations in the TKA knee compared to the CoCr component. An increased deformation of the PEEK component indicates a reduction in its structural strength. Future investigation should examine if the reduced structural strength will affect the in-vivo component-bone interface integration and affect the component fatigue life.

In vivo contact kinematics and contact forces of the knee after total knee arthroplasty during dynamic weight-bearing activities.

Analysis of polyethylene component wear and implant loosening in total knee arthroplasty (TKA) requires precise knowledge of in vivo articular motion and loading conditions. This study presents a simultaneous in vivo measurement of tibiofemoral articular contact forces and contact kinematics in three TKA patients. These measurements were accomplished via a dual fluoroscopic imaging system and instrumented tibial implants, during dynamic single leg lunge and chair rising-sitting. The measured forces and contact locations were also used to determine mediolateral distribution of axial contact forces. Contact kinematics data showed a medial pivot during flexion of the knee, for all patients in the study. Average axial forces were higher for lunge compared to chair rising-sitting (224% vs. 187% body weight). In this study, we measured peak anteroposterior and mediolateral forces averaging 13.3% BW during lunge and 18.5% BW during chair rising-sitting. Mediolateral distributions of axial contact force were both patient and activity specific. All patients showed equitable medial-lateral loading during lunge but greater loads at the lateral compartment during chair rising-sitting. The results of this study may enable more accurate reproduction of in vivo loads and articular motion patterns in wear simulators and finite element models. This in turn may help advance our understanding of factors limiting longevity of TKA implants, such as aseptic loosening and polyethylene component wear, and enable improved TKA designs.

In vivo anterior tibial post contact after posterior stabilizing total knee arthroplasty.

Anterior polyethylene post failure in posterior stabilizing total knee arthroplasty (TKA) has been reported in recent patient follow-up studies. However, no data have been reported on the biomechanic interaction between the anterior tibial post and femoral component in posterior stabilizing TKA patients under physiological conditions. The objective of this study was to measure the in vivo anterior tibial post contact area at full knee extension using a dual-orthogonal fluoroscopic imaging technique. Eleven osteoarthritic patients were investigated after posterior stabilizing TKA to measure the contact between the femoral component box and anterior aspect of the tibial post. Anterior tibial post contact, ranging between 0.5 and 80.9 mm(2), was detected in 63% of the healthy patients (seven out of the eleven patients) at weight-bearing full extension of the knee. The patients with anterior tibial post contact had significantly higher hyperextension angles (-8.4 +/- 4.3 degrees) than those without contact (1.4 +/- 7.2 degrees). A statistically significant difference was also detected in the femoral component flexion with respect to the femoral shaft between the patients with anterior post contact (2.7 +/- 2.7 degrees) and without anterior post contact (-1.3 +/- 2.2 degrees). These data indicated that anterior post contact did occur in hyperextension within posterior stabilizing TKA patients. While excessive anterior tibial post contact may cause polyethylene wear and potentially lead to post failure, the tibial post may also act as a substitute for the ACL at low flexion, thus providing stability to the joint after posterior stabilizing TKA.

Endoscopically assisted anterior release and reduction through anterolateral retropharyngeal approach for fixed atlantoaxial dislocation.

STUDY DESIGN: A prospective study. OBJECTIVE: To evaluate a novel technique involving an endoscopically assisted anterior release and reduction through an anterolateral retropharyngeal approach with minimum follow-up interval of 31 months. SUMMARY OF BACKGROUND DATA: Irreducible atlantoaxial dislocation is typically a chronic process that requires surgical treatment. However, the current literature does not agree on the single best method of treatment. Previously, the best outcomes have been reported with transoral reduction followed by anterior or posterior fixation. Despite recent innovations, numerous complications remain associated with this approach. METHODS: About 21 consecutive irreducible atlantoaxial dislocation patients with mean age of 32 years underwent endoscopically assisted anterior release and reduction through the anterolateral retropharyngeal approach followed by posterior fixation. The primary pathologies included 8 late odontoid fractures, 7 cases of os odontoideum, 5 with laxity of the transverse ligament, and 1 with atlanto-occipital assimilation with a hypoplastic odontoid. Neurologic status was evaluated using the Japanese Orthopedic Association scoring system. Radiographic parameters including the atlantodental interval (ADI) and cervicomedullary angle were also measured. Follow-up data were obtained for a minimum of 31 months. RESULTS: Anatomic reduction was achieved in 20 cases and near-anatomic reduction in 1 case. All patients had an uneventful recovery with significant improvement in neurologic function and radiographic parameters. No complications were seen. The atlantodental interval was corrected from an average 6.3 mm before surgery to 2.7 mm after surgery (P < 0.01). The cervicomedullary angle was also corrected from an average 109 degrees before surgery to 152 degrees after surgery (P < 0.01). Preoperative muscle strength was on average 3.5 (on scale from 1 to 5) and improved after surgery to 4.5 (P < 0.01). The average preoperative and postoperative Japanese Orthopedic Association scores were 9.6 and 15.5, respectively, indicating 82.8% improvement. CONCLUSION: Endoscopically assisted anterior retropharyngeal release combined with posterior fixation is a safe and effective alternative for the treatment of irreducible atlantoaxial dislocation.