Bioinert Control of Zwitterionic Poly(ethylene terephtalate) Fibrous Membranes.

Poly(ethylene terephtalate) (PET)-based materials face general biofouling issues that we addressed by grafting a copolymer of glycidyl methacrylate and sulfobetaine methacrylate, poly(GMA- r-SBMA). The grafting procedure involved a dip-coating step followed by UV-exposure and led to successful grafting of the copolymer as evidenced by X-ray photoelectron spectroscopy and zeta potential measurements. It did not modify the pore size nor the porosity of the PET membranes. In addition, their surface hydrophilicity was considerably improved, with a water contact angle falling to 30° in less than 20 s and 0° in less than 1 min. The effect of copolymer concentration in the coating bath (dip-coating procedure) and UV exposure time (UV step) were scrutinized during biofouling studies involving several bacteria such as Escherichia coli and Stenotrophomonas maltophilia, but also whole blood and HT1080 fibroblasts cells. The results indicate that if all conditions led to improved biofouling mitigation, due to the efficiency of the zwitterionic copolymer and grafting procedure, a higher concentration (15 mg/mL) and longer UV exposure time (at least 10 min) enhanced the grafting density which reflected on the biofouling results and permitted a better general biofouling control regardless of the nature of the biofoulant (bacteria, blood cells, fibroblasts).

Leveraging the Dielectric Barrier Discharge Plasma Process to Create Regenerative Biocidal ePTFE Membranes.

The utilization of dielectric barrier discharge (DBD) plasma treatment for modifying substrate surfaces constitutes an easy and simple approach with a potential for diverse applications. This technique was used to modify the surface of a commercial porous expanded poly(tetrafluoroethylene) (ePTFE) film with either dimethylaminoethyl methacrylate (DMAEMA) or (trimethylamino)ethyl methacrylate chloride (TMAEMA) monomers, aiming to obtain antibacterial ePTFE. Physicochemical analyses of the membranes revealed that DBD successfully enhanced the surface energy and surface charge of the membranes while maintaining high porosity (>75%) and large pore size (>1.0 µm). Evaluation of the bacteria killing-releasing (K-R) function revealed that both DMAEMA and TMAEMA endowed ePTFE with the ability to kill Escherichia coli bacteria. However, only TMAEMA-grafted ePTFE allowed for the release of dead bacteria from the surface upon washing with sodium hexametaphosphate (SHMP) saline solution, owing to its cationic charge derived from the quaternary amine. Washing with SHMP disturbed the electrostatic force between the polymer brushes and dead bacteria, which caused the release of the dead bacteria. Lastly, dead-end bacteria filtration showed that the TMAEMA-grafted ePTFE was able to kill 99.78% of the bacteria, while approximately 61.55% of bacteria were killed upon contact. The present findings support the feasibility of using DBD plasma treatment for designing surfaces that target bacteria and aid in the containment of disease-causing pathogens.

Self-Assembly Anchored Cationic Copolymer Interfaces for Applying the Control of Counterion-Induced Bacteria Killing/Release Procedure.

In recent years, daily hygiene and disease control issues have received increasing attention, especially the raging epidemics caused by the spread of deadly viruses. The construction of the interface of new polymer materials is focused on, which can provide a cyclic operation process for the killing and releasing of bacteria, and perform repeated regeneration, which is of great significance for the development of advanced medical biomaterials. In order to explore the basic physical phenomena of bacterial attachment and detachment on the polymer material interface by different amine groups, this study plans to synthesize four different butyl methacrylate (BMA)-based cationic copolymers with primary, ternary, and quaternary amine groups, and compare their effects on bactericidal efficiency. Since BMA can generate strong hydrophobic interactions with the benzene ring structure, this study used a polystyrene substrate to realize a self-assembled cationic copolymer interface for controlling the counterion-induced bacterial killing/release process. Furthermore, negatively charged ions are introduced to induce changes in the hydration capability of water molecules and control the subsequent bacterial detachment function. In this study, possible directions to answer and clarify the above concepts are proposed, and there is a basic reference principle that can lead to research work in macromolecular bioscience fields.