Liposomes coated with N-trimethyl chitosan to improve the absorption of harmine in vivo and in vitro.

In this study, harmine liposomes (HM-lip) were prepared through the thin-film hydration-pH-gradient method and then coated with N-trimethyl chitosan (TMC). Particle size, zeta potential, entrapment efficiency, and in vitro release of HM-lip and TMC-coated harmine liposomes (TMC-HM-lip) were also determined. Sprague Dawley rats were further used to investigate the pharmacokinetics in vivo. Retention behavior in mouse gastrointestinal tract (GIT) was studied through high-performance liquid chromatography and near-infrared imaging. Degradation was further evaluated through incubation with Caco-2 cell homogenates, and a Caco-2 monolayer cell model was used to investigate the uptake and transport of drugs. HM-lip and TMC-HM-lip with particle size of 150-170 nm, an entrapment efficiency of about 81%, and a zeta potential of negative and positive, respectively, were prepared. The release of HM from HM-lip and TMC-HM-lip was slower than that from HM solution and was sensitive to pH. TMC-HM-lip exhibited higher oral bioavailability and had prolonged retention time in GIT. HM-lip and TMC-HM-lip could also protect HM against degradation in Caco-2 cell homogenates. The uptake amount of TMC-HM-lip was higher than that of HM and HM-lip. TMC-HM-lip further demonstrated higher apparent permeability coefficient (P(app)) from the apical to the basolateral side than HM and HM-lip because of its higher uptake and capability to open tight junctions in the cell monolayers. TMC-HM-lip can prolong the retention time in the GIT, protect HM against enzyme degradation, and improve transport across Caco-2 cell monolayers, thus enhancing the oral bioavailability of HM.

Chitin/PLGA blend microspheres as a biodegradable drug-delivery system: phase-separation, degradation and release behavior.

A novel chitin-based microsphere was developed for anti-cancer drug-delivery purpose in the present study. These biodegradable microspheres were prepared by directly blending chitin with different contents of poly(D,L-lactide-co-glycolide 50:50) (PLGA 50/50) in dimethylacetamide-lithium chloride solution, and following it by coagulating in water via wet phase inversion. Scanning electron microscopy (SEM) micrography of the blend microsphere showed that there are numerous PLGA particulates homogeneously dispersed in chitin matrix, suggesting the occurrence of obvious phase separation from the blended chitin and PLGA 50/50 phase due to their thermodynamic incompatibility. Degradation of the chitin/PLGA 50/50 blend microsphere depends on the surface erosion of chitin phase and bulk hydrolysis of PLGA phase, according to the examinations of SEM and differential scanning calorimetry studies. Weight loss of the chitin/PLGA 50/50 blend microsphere increases with the increase of chitin content in the microsphere. A two-phase drug-release model is observed from the release of chlorambucil from chitin/PLGA 50/50 blend microspheres. The initial stage of drug-release rate increases with the increased chitin content due to the hydration and surface erosion of hydrophilic chitin phase; however, the following stage of slow release is sustained for several days, mainly contributed by the bulk hydrolysis of hydrophobic PLGA phase. In conclusion, such a chitin/PLGA 50/50 blend microsphere is novel and interesting, and may be used as a special drug-delivery system.

Chitin/PLGA blend microspheres as a biodegradable drug delivery system: a new delivery system for protein.

Novel chitin/PLGAs and chitin/PLA based microspheres were developed for the delivery of protein. These biodegradable microspheres were prepared by polymers blending and wet phase-inversion methods. The parameters such as selected non-solvents, temperature of water and ratio of polylactide to polyglycolide were adjusted to improve thermodynamic compatibility of individual polymer (chitin and PLGAs or chitin/PLA), which affects the hydration and degradation properties of the blend microspheres. Triphasic pattern of drug release model is observed from the release of protein from the chitin/PLGAs and chitin/PLA microspheres: the initially fast release (the first phase), the following slow release (the second phase) and the second burst release (the third phase). Formulations of the blends, which are based on the balance among the hydration rate of the chitin phase and degradation of chitin/PLA and PLGA phase, can lead to a controllable release of bovine serum albumin (BSA). In conclusion, such a chitin/PLGA 50/50 microsphere is novel and interesting, and may be used as a protein delivery system.