RESUMEN
Crospovidone is a commonly used tablet disintegrant. However, the synthetic disintegrant has been known to be hygroscopic and high moisture content in crospovidone used could exert deleterious effects on tablets formulated with it. The objective of this study was to elicit a better understanding between crospovidone-water interaction and its effect on disintegrant performance. Moisture sorption and desorption isotherms were obtained together with the enthalpy of immersion. Crospovidone samples stored at four relative humidities were used to formulate tablets and the resultant tablets were evaluated for their mechanical, dimensional and disintegratability attributes. Analyses of the moisture sorption isotherms indicated that externally adsorbed moisture accounted for the bulk of the total moisture content in crospovidone, with minimal amount of moisture absorbed intramolecularly. Enthalpy of immersion became less exothermic with crospovidone samples stored at increasing storage humidity. Correspondingly, improvement in disintegration time became less pronounced. This was postulated to be a consequence of premature wetting of the particle surfaces by externally adsorbed moisture. High humidity was also detrimental to tablet hardness and thickness. In conclusion, the impact of moisture sorption during storage by excipients such as crospovidone could be better understood by the appreciation of crospovidone-water interaction and its consequence on tablet quality.
Asunto(s)
Povidona/química , Agua/química , Adsorción , Química Farmacéutica/métodos , Excipientes/química , Dureza , Humedad , Comprimidos/químicaRESUMEN
Respiratory infections represent a major global health problem. They are often treated by parenteral administrations of antimicrobials. Unfortunately, systemic therapies of high-dose antimicrobials can lead to severe adverse effects and this calls for a need to develop inhaled formulations that enable targeted drug delivery to the airways with minimal systemic drug exposure. Recent technological advances facilitate the development of inhaled anti-microbial therapies. The newer mesh nebulisers have achieved minimal drug residue, higher aerosolisation efficiencies and rapid administration compared to traditional jet nebulisers. Novel particle engineering and intelligent device design also make dry powder inhalers appealing for the delivery of high-dose antibiotics. In view of the fact that no new antibiotic entities against multi-drug resistant bacteria have come close to commercialisation, advanced formulation strategies are in high demand for combating respiratory 'super bugs'.
Asunto(s)
Antibacterianos/administración & dosificación , Antifúngicos/administración & dosificación , Antivirales/administración & dosificación , Sistemas de Liberación de Medicamentos/métodos , Infecciones del Sistema Respiratorio/tratamiento farmacológico , Administración por Inhalación , Aerosoles , Antibacterianos/química , Antibacterianos/uso terapéutico , Antifúngicos/química , Antifúngicos/uso terapéutico , Antivirales/química , Antivirales/uso terapéutico , Sistemas de Liberación de Medicamentos/instrumentación , Estabilidad de Medicamentos , Inhaladores de Polvo Seco , Humanos , Liposomas , Nanopartículas , Tamaño de la Partícula , Propiedades de SuperficieRESUMEN
Binder distribution in the powder mass during high shear granulation is especially critical with the use of viscous liquid binders and with short processing times. A viscous liquid binder was delivered into the powder mass at two flow rates using three methods: pouring, pumping and spraying from a pressure pot. Binder content analyses at the scale of individual granules were conducted to investigate the impact of different delivery conditions on the homogeneity of binder distribution. There was clear evidence of non-uniformity of binder content among individual granules across all delivery conditions, particularly for the fast rates of delivery. Poorer reproducibility values of tablet thickness and disintegration time were observed when binder was poured but this may be overcome by pumping or spraying from the pressure pot. Greater homogeneity of binder distribution occurred with the slow rates of delivery and led to the earlier onset of granule growth and a consequent increase in granule size. Larger granule size and lower proportion of fines were in turn associated with increased granule bulk density and improvement of granule flow. In conclusion, delivery of a viscous binder at a slow rate either by pumping or via a pressure pot was most desirable during granulation.