Effect of Viscosity on the Formation of Porous Polydimethylsiloxane for Wearable Device Applications.

Medical devices, which enhance the quality of life, have experienced a gradual increase in demand. Various research groups have attempted to incorporate soft materials such as skin into wearable devices. We developed a stretchable substrate with high elasticity by forming a porous structure on polydimethylsiloxane (PDMS). To optimize the porous structure, we propose a manufacturing process that utilizes a high-pressure steam with different viscosities (400, 800, 2100, and 3000 cP) of an uncured PDMS solution. The proposed method simplifies the manufacturing of porous structures and is cost-effective compared to other technologies. Porous structures of various viscosities were formed, and their electrical and mechanical properties evaluated. Porous PDMS (3000 cP) was formed in a sponge-like three-dimensional porous structure, compared to PDMS formed by other viscosities. The elongation of porous PDMS (3000 cP) was increased by up to 30%, and the relative resistance changed to less than 1000 times with the maximum strain test. The relative resistance increased the initial resistance (R0) by approximately 10 times during the 1500-times repeated cycling tests with 30% strain. As a result, patch-type wearable devices based on soft materials can provide an innovative platform that can connect with the human skin for robotics applications and for continuous health monitoring.

Postoperative Three-Dimensional Evaluation of Mandibular Contouring Surgery Using Computer-Assisted Simulation Planning and a Three-Dimensional-Printed Surgical Guide.

Mandibular contouring surgery was performed using computer-assisted simulation planning (CASP) and 3-dimensional printed surgical guide. The outcome of the surgery was evaluated by overlapping preoperative image. The patient underwent mandibular contouring surgery according to CASP for his residual facial asymmetry of the mandibular angle and mental area. The overall facial aesthetic of the patient was improved. In the overlapping image, the left mandibular border area was slightly overcorrected. However, the other portion was operated as planned. The overcorrection was due to the improper adaptation of the surgical guide adjacent to the mental foramen. In conclusion, usage of CASP and a surgical guide could reduce operation time and increase the accuracy of the operation. However, the design of the stent should be improved around the mental foramen to avoid nerve damage and improper adaptation.

Pedicled buccal fat pad flap as a reliable surgical strategy for the treatment of medication-related osteonecrosis of the jaw.

PURPOSE: The purpose of this study was to evaluate the coverage of the pedicled buccal fat pad flap (PBFP) and the long-term results of this treatment in patients with medication-related osteonecrosis of the jaw (MRONJ). PATIENTS AND METHODS: Ten patients (2 men and 8 women; average age, 72.9 yr old) diagnosed with MRONJ were selected. Patients were treated with a PBFP. Data from patients regarding MRONJ stage, defect size, bone exposure after surgery, operation time, admission period, duration of antibiotic therapy, recurrence of disease, and postoperative complications were analyzed retrospectively. RESULTS: Six patients were diagnosed with MRONJ stage 2, and 4 patients were diagnosed with MRONJ stage 3. The maximum defect in the study was 62 × 18 mm. Among the 10 patients, there was only 1 bony exposure, which occurred on postoperative day 2 after receiving the PBFP. This exposure might have been due to an incomplete resection of the affected bone. There were no severe donor site morbidities, and all patients showed satisfactory healing without incident. CONCLUSIONS: According to this evaluation, the PBFP effectively covered a relatively large surgical defect. Complications were minimal, and there was no recurrence of bony exposure during follow-up. In conclusion, using the PBFP was a reliable treatment option for the management of denuded bone in patients with MRONJ.

Investigating the accuracy of mandibulectomy and reconstructive surgery using 3D customized implants and surgical guides in a rabbit model.

BACKGROUND: This study aimed to analyze the accuracy of the output of three-dimensional (3D) customized surgical guides and titanium implants in a rabbit model, and of mandibulectomy, reconstructive surgery, and surgical outcome; additionally, the correlation between surgical accuracy and surgical outcomes, including the differences in surgical outcome according to surgical accuracy, was analyzed. RESULTS: The output of implants was accurately implemented within the error range (- 0.03-0.03 mm), and the surgical accuracy varied depending on the measured area (range - 0.4-1.1 mm). Regarding surgical outcomes, angle between the mandibular lower borders showed the most sensitive results and distance between the lingual cusps of the first molars represented the most accurate outcomes. A significant correlation was noted between surgical accuracy in the anteroposterior length of the upper borders pre- and postoperatively and the angle between the mandibular lower borders (regression coefficient = 0.491, p = 0.028). In the group wherein surgery was performed more accurately, the angle between the mandibular lower borders was reproduced more accurately (p = 0.021). A selective laser melting machine accurately printed the implants as designed. Considering the positive correlation among surgical accuracy in the mandibular upper borders, angle between the mandibular lower borders, and more accurately reproduced angle between the mandibular lower borders, the angle between the mandibular lower borders is considered a good indicator for evaluating the outcomes of reconstructive surgery. CONCLUSION: To reduce errors in surgical outcomes, it is necessary to devise a positioner for the surgical guide and design a 3D surgical guide to constantly maintain the direction of bone resection. A fixed area considering the concept of three-point fixation should be selected for stable positioning of the implant; in some cases, bilateral cortical bone fixation should be considered. The angle between the mandibular lower borders is a sensitive indicator for evaluating the outcomes of reconstructive surgery.

Surgery-first approach reduces the overall treatment time without damaging long-term stability in the skeletal class III correction: a preliminary study.

BACKGROUND: Compared to the conventional approach, including preoperative orthodontic preparation, the so-called surgery-first approach (SFA) seems to reduce the overall treatment time in the correction of skeletal class III dentofacial deformity. However, there have been controversies about postoperative skeletal stability with SFA. Therefore, we investigated the long-term stability and the overall treatment time after maxillomandibular surgery for skeletal class III correction with or without preoperative orthodontic preparation. METHODS: This retrospective study included eight patients who underwent maxillomandibular surgery for class III correction with the SFA (SFA group) and 20 patients who underwent the conventional approach (CA group). A comparative study of the change in the maxillary and mandibular position on preoperative (T1), 1-day (T2), 6-month (T3), and 2-year (T4) postoperative lateral cephalograms. We calculated the overall treatment time for each group. RESULTS: At the presurgical stage (T1), there was no bias in the skeletal features between the two groups. In the surgical change from T1 to T2, the mandible (point B) of the CA group was significantly moved superiorly. Short-term changes from T2 to T3 revealed that the mandible moved forward in both groups, whereas the maxillary position showed no significant changes. Long-term changes from T3 to T4 demonstrated that none of the measured parameters showed any significant differences. Finally, the average of overall treatment time was 15.1 months in the SFA group and 26.0 months in the CA group. CONCLUSIONS: These findings suggest that SFA in bimaxillary orthognathic surgery for skeletal class III correction leads to predictable long-term skeletal stability, similar to surgery with CA. Furthermore, SFA reduced the overall treatment time compared to CA.

Comparative study of the prognosis of an extracorporeal reduction and a closed treatment in mandibular condyle head and/or neck fractures.

PURPOSE: The objective of this study was a comparison of the prognosis between an extracorporeal reduction technique and closed treatment of a mandibular condyle fracture. The relationship between condylar resorption and several clinical variables was also studied. PATIENTS AND METHODS: Seventy-one patients who had a mandibular condyle fracture took part in this study. Thirty-five patients (female: 7, male: 28, age: 30.46 ± 14.27 years) were treated by extracorporeal reduction, and 36 patients (male: 24, female: 12, age: 24.28 ± 9.99 years) were treated using a closed treatment. The presence of complications such as condylar resorption, malocclusion, nerve disorder, and disc displacement was evaluated with panoramic radiographs and clinical examinations 12 months after treatment. The relationships between the complications and other clinical variables were evaluated statistically. RESULTS: The anatomic site and fracture type were closely related to condyle resorption in the bivariate analysis. Condylar head fractures showed significantly higher condyle resorption than condylar neck fractures (P = .023). A complex or compound fracture showed significantly higher condyle resorption compared with a simple fracture (P = .006). Patients who had a complex/compound fracture were 34.366 times more likely to have condyle resorption compared with those who had a simple fracture (P = .002). The patient's age and treatment method were also significant predictors for condyle resorption. CONCLUSION: Fracture type was the strongest predictor of condylar resorption. Because treatment method and patient age were also related to the prognosis, the optimal treatment for mandibular condylar head and/or neck fractures should be individualized according to the patient's condition.

Hydrophobic nanopatterning on a flexible gas barrier film by using a poly(dimethylsiloxane) elastomer.

In this work, we fabricated a hydrophobic and transparent gas barrier film via a nanopatterned poly(dimethylsiloxane) elastomer imprinting on an ultraviolet-curable polymer resin. A Ca degradation method (water permeation rate) and surface energy measurements were used to determine the level of modification of the surface characteristics. As a result, the decreased surface energy from 25.8 to 7.29 mN m(-1) led to a lower water vapor transmission rate from 3.06 x 10(-1) to 6.24 x 10(-2) g m(-2) day(-1) according to the degree of decreased Ca height from 100 nm. A tunable wettability is beneficial for application where controlling the direction of moisture flow is important, such as in flexible organic electronics.

Temporomandibular joint ankylosis caused by chondroid hyperplasia from the callus of condylar neck fracture.

A patient who complained of difficulty in opening his mouth after condylar neck fracture 1 year ago presented typical features of temporomandibular joint ankylosis in clinical and radiologic examinations. To demonstrate a possible pathogenesis of temporomandibular joint ankylosis after condylar neck fracture, the fractured condylar portion removed was examined by histologic and immunohistochemical stainings. Interpositional gap arthroplasty was performed by removing the inferomesially displaced fractured condyle, and reconstruction with subcutaneous dermis to the previous vertical height was performed immediately. The fractured condylar portion was almost intact with slight erosion of the condylar cartilage. In the hematoxylin and eosin and Masson trichrome stainings, an extensive chondroid hyperplasia with abundant hyaline cartilage was shown in the removed condylar portion. There were also hyperplastic features of the synovial membrane, which were abnormally distributed throughout the chondroid tissues. In the immunohistochemical stainings of proliferating cell nuclear antigen (PCNA) and bone morphogenetic protein (BMP)-2 and BMP-4, the chondroid tissues were conspicuously hyperplastic and strongly positive for BMP-4 but sparse for BMP-2. From these results, we think that the hyperplastic chondroid tissue was derived from the callus of the primary fractured site of the condylar neck and propose that the chondroid tissue could proliferate continuously because of synovial tissue support from around the temporomandibular joint, resulting in temporomandibular joint ankylosis. This pathogenesis is quite different from those of other diaphyseal fracture of long bones.

Comparative study on long-term stability in mandibular sagittal split ramus osteotomy: hydroxyapatite/poly-l-lactide mesh versus titanium miniplate.

BACKGROUND: Resorbable devices have recently been adopted in the field of orthognathic surgery with controversies about their postoperative skeletal stability. Hence, we determined the long-term skeletal stability of unsintered hydroxyapatite/poly-l-lactic acid (HA/PLLA) mesh for osteofixation of mandibular sagittal split ramus osteotomy (SSRO), and compared it with that of titanium miniplate. METHODS: Patients were divided into resorbable mesh and titanium miniplate fixation groups. A comparative study of the change in the mandibular position was performed with preoperative, 1-day, 6-month, and 2-year postoperative lateral cephalograms. RESULTS: At postoperative 6 months-compared with postoperative 1 day, point B (supra-mentale) was significantly displaced anteriorly in the titanium-fixation group. Moreover, at postoperative 2 years-compared with postoperative 6 months, point B was significantly displaced inferiorly in the titanium-fixation. However, the HA/PLLA mesh-fixation group did not show any significant change with respect to point B postoperatively. CONCLUSIONS: The HA/PLLA mesh-fixation group demonstrated superior long-term skeletal stability with respect to the position of mandible, when compared with the titanium-fixation group.

The effect of fixation plate use on bone healing during the reconstruction of mandibular defects.

OBJECTIVES: This study sought to compare efficiency results between the use of a customized implant (CI) and a reconstruction plate (RP) in mandibular defect reconstruction in an animal model. MATERIALS AND METHODS: Fifteen rabbits underwent surgery to create a defect in the right side of the mandible and were randomly divided into two groups. For reconstruction of the mandibular defect, the RP group (n=5) received five-hole mini-plates without bone grafting and the CI group (n=10) received fabricated CIs based on the cone-beam computed tomography (CBCT) data taken preoperatively. The CI group was further divided into two subgroups depending on the time of CBCT performance preoperatively, as follows: a six-week CI (6WCI) group (n=5) and a one-week CI (1WCI) group (n=5). Daily food intake amount (DFIA) was measured to assess the recovery rate. Radiographic images were acquired to evaluate screw quantity. CBCT and histological examination were performed in the CI subgroup after sacrifice. RESULTS: The 1WCI group showed the highest value in peak average recovery rate and the fastest average recovery rate. In terms of reaching a 50% recovery rate, the 1WCI group required the least number of days as compared with the other groups (2.6±1.3 days), while the RP group required the least number of days to reach an 80% recovery rate (7.8±2.2 days). The 1WCI group showed the highest percentage of intact screws (94.3%). New bone formation was observed in the CI group during histological examination. CONCLUSION: Rabbits with mandibular defects treated with CI showed higher and faster recovery rates and more favorable screw status as compared with those treated with a five-hole mini-plate without bone graft.

Evaluation of gas permeation barrier properties using electrical measurements of calcium degradation.

In this work, we developed a thin calcium degradation method introducing sensitive electrical resistance monitoring. We have demonstrated structural models of the inorganic/organic thin films to evaluate barrier properties against water and oxygen permeation. The time-dependent transmission curve of a multibarrier coated on both sides of the polyethersulfone substrate had a linear slope which was measured as 5.17 x 10(-3) gm(2) day at 20 degrees C and 60% relative humidity. This system can measure an accurate permeation rate with a high sensitivity in the measurable range of 10(1)-10(-6) gm(2) day. In addition, the test structure devised is applicable to various fabrication techniques for passivation layers with durability and ultralow permeability for flexible organic light emitting diodes.

Use of mandibular chin bone for alveolar bone grafting in cleft patients.

BACKGROUND: We evaluated and compared the outcomes of different ossification processes in patients with alveolar cleft in whom correction was performed using endochondral bone graft or intramembranous bone graft. METHODS: The patients were divided into two groups: the endochondral bone (iliac bone or rib bone) graft group and the intramembranous bone (mandibular bone) graft group. Medical records and radiologic images of patients who underwent alveolar bone grafting due to alveolar cleft were analyzed retrospectively. Through postoperative and follow-up radiologic images, the height of the interdental bone septum was classified into four types based on the highest point of alveolar ridge. Then, the height of the interdental bone septum and the area of the bone graft were evaluated according to the type of bone graft. In addition, the occurrence of complications and the need for an additional bone graft, the result of postoperative orthodontic treatment, and the eruption of impacted teeth were investigated. RESULTS: Thirty patients were included in this study. There was no significant difference in the change of the interdental bone height and the area of the bone graft according to the type of bone. There was no significant difference in the success rate of the surgery according to the type of bone. One patient underwent an additional bone graft surgery during the follow-up period. CONCLUSIONS: The outcomes of alveolar bone grafting were not significantly different according to the type of bone graft. If appropriate to the size of the recipient site, the chin bone is a useful graft material in alveolar cleft, as is the iliac bone.

Long-term follow-up of early cleft maxillary distraction.

BACKGROUND: Most of cleft lip and palate patients have the esthetic and functional problems of midfacial deficiencies due to innate developmental tendency and scar tissues from repeated operations. In these cases, maxillary protraction is required for the harmonious facial esthetics and functional occlusion. CASE PRESENTATION: A 7-year old boy had been diagnosed as severe maxillary constriction due to unilateral complete cleft lip and palate. The author tried to correct the secondary deformity by early distraction osteogenesis with the aim of avoiding marked psychological impact from peers of elementary school. From 1999 to 2006, repeated treatments, which consisted of Le Fort I osteotomy and face mask distraction, and complementary maxillary protraction using miniplates were performed including orthodontics. But, final facial profile was not satisfactory, which needs compromising surgery. CONCLUSIONS: The result of this study suggests that if early distraction treatment is performed before facial skeletal growth is completed, an orthognathic surgery or additional distraction may be needed later. Maxillofacial plastic and reconstructive surgeons should notify this point when they plan early distraction treatment for cleft maxillary deformity.

Change of the airway space in mandibular prognathism after bimaxillary surgery involving maxillary posterior impaction.

BACKGROUND: The purpose of this retrospective study was to develop a two- and three-dimensional analysis of the airway using cone-beam computed tomography (CBCT) and to determine whether the airway space would be changed in mandibular prognathism after bimaxillary surgery involving maxillary posterior impaction. METHODS: Patients requiring orthognathic surgery from 2012 to 2014 were recruited for this study. CBCT scans were obtained at three points: preoperatively (T0), immediate postoperatively (T1), and after 6 months postoperatively (T2). The nasopharynx, oropharynx, and hypopharynx were measured on the CBCT scan for each patient in a repeatable manner. With the midsagittal plane, linear measurements in the middle of each were obtained. For the CBCT, volumetric measurements of each and total airway were obtained. RESULTS: A total of 22 consecutive patients (11 men and 11 women) were included in the present study. The total volume was significantly reduced (p < .001). However, the change of the diameter and volume of the nasopharynx was not statistically significant (p = .160, p = .137, respectively). In the oropharynx, the change of both the diameter and volume showed statistical significance between preoperatively and immediate postoperatively (p < .001, p = .001, respectively) and also preoperatively and after 6 months postoperatively (p = .001, p = .010, respectively). In the hypopharynx, the change of both the diameter and volume showed statistical significance between preoperatively and immediate postoperatively (p = .001, p < .001, respectively) and also preoperatively and after 6 months postoperatively (p = .001, p < .001, respectively). CONCLUSIONS: The bimaxillary surgery involving maxillary posterior impaction can reduce the volume of airway in the patients of mandibular prognathism. Although total airway volume was reduced significantly, the changes in the volume and diameter of the nasopharynx were not statistically significant. The maxillary posterior impaction affects on the nasopharyngeal airway minimally.

Bimaxillary orthognathic surgery and condylectomy for mandibular condyle osteochondroma: a case report.

Osteochondroma is rarely reported in the maxillofacial region; however, it is prevalent in the mandibular condyle. This slowly growing tumor may lead to malocclusion and facial asymmetry. A 39-year-old woman complained of gradual development of anterior and posterior unilateral crossbite, which resulted in facial asymmetry. A radiological study disclosed a large tumor mass on the top of the left mandibular condyle. This bony tumor was surgically removed through condylectomy and the remaining condyle head was secured. Subsequently, bimaxillary orthognathic surgery was performed to correct facial asymmetry and malocclusion. Pathological diagnosis was osteochondroma; immunohistochemistry showed that the tumor exhibited a conspicuous expression of BMP-4 and BMP-2 but rarely expression of PCNA. There was no recurrence at least for 1 year after the operation. Patient's functional and esthetic rehabilitation was uneventful.

Novel composite layer based on electrospun polymer nanofibers for efficient light scattering.

We fabricated a PAN (polyacrylonitrile) NF (nanofiber)-embedded composite layer to adjust the light-control layer in light-emitting-diode (LED) and organic-light-emitting-diode (OLED) lighting systems with unique optical characteristics, for effective light scattering. The newly designed light-control composite layers with a composition of PAN NF/SU-8 exhibited a change in the optical properties, which was identified by the diameter control of the NF using a simple process. The change in the optical properties was largely dependent on the embedded NF's features. Therefore, the NF can be applied in different types of lighting systems, depending on each lighting device's purpose.

Positional stability following intentional posterior ostectomy of the distal segment in bilateral sagittal split ramus osteotomy for correction of mandibular prognathism.

PURPOSE: In order to minimize post-operative relapse after mandibular setback using bilateral sagittal split ramus osteotomy, we have recently tried a technique, i.e. intentional ostectomy of the posterior part of the distal segment. The aim of this study was to evaluate the effects of this technique on the frequencies and extent of post-operative relapse. PATIENTS: This study was based on 61 cases of mandibular prognathism. The traditional sagittal split was performed in 24 cases (average age: 22.0+/-3.8) as a control group and the technique of additional distal ostectomy was used in the other 37 cases (average age: 23.2+/-3.2) as a test group. METHODS: Horizontal and vertical changes in the position of the body of the mandible were measured to determine the amount of long-term post-operative relapse. The amount of relapse was compared between groups and the statistical significance of the differences was evaluated. RESULTS: The relapse index of the test group was significantly lower than that of the control group in the 6- and 12-month post-operative periods (p>0.005). The horizontal relapse index and facial length relapse index of the test group were lower than those of the control group 12 months post-operatively (p<0.05). CONCLUSION: This method should be considered as a useful method to maximise long-term post-operative stability.

Positional change of the condyle after orthodontic-orthognathic surgical treatment: is there a relationship to skeletal relapse?

OBJECTIVES: The purpose of this study was to evaluate the condylar position in relation to the glenoid fossa before and after orthodontic-orthognathic surgical treatment and to investigate the relationship with skeletal relapse. MATERIALS AND METHODS: Lateral cephalograms and temporomandibular joint tomograms from 19 patients with mandibular prognathism who received orthodontic-orthognathic surgery were included in this study. Samples were divided into two groups based on skeletal change during the retention period. The relapse group consisted of 7 patients (3 females and 4 males; mean age, 21.9 years) whose pogonion or menton displaced more than 1 mm during the retention period and the stable group consisted of 12 patients (5 females and 7 males; mean age, 21.7 years). Anterior joint space, posterior joint space, superior joint space, and anteroposterior index were measured on tomograms at pretreatment and posttreatment timepoints. Condyle position and frequency of the positional change were compared between both groups. RESULTS: In the relapse group and stable group, 42.9% and 45.8% of the condyles, respectively, showed forward or backward displacement at posttreatment. However, the changes were small and the mean anterior, posterior, superior joint spaces and frequencies of the positional changes did not differ statistically between both groups. CONCLUSION: Our results suggest that small positional changes of the condyle, which may occur after orthodontic-orthognathic surgery treatment, may not be related to skeletal relapse after removal of the orthodontic appliances.

Defatting Vestibuloplasty for Functional and Esthetic Reconstruction of Tongue.

The radial forearm free flap (RFFF) is a thin and pliable tissue with many advantages for tongue reconstruction. However, tongues reconstructed with RFFF occasionally need revision surgery because inadequate defect measurement at primary surgery can lead to bulkiness and limited movement of reconstructed tongue. In this case, the patient underwent partial glossectomy and RFFF reconstruction for treatment of tongue cancer five years prior. We could not make a lower denture for the patient, because the alveolo-lingual sulcus of tongue was almost lost. So we performed vestibuloplasty with a modified Kazanjian method on the lingual vestibule of the mandibular right posterior area, and defatting surgery to debulk the flap. After surgery, we observed that the color and texture of the revised tongue changed to become similar with adjacent tissue. The patient obtained a more functional and esthetic outcome. Accordingly, we present a case report with a review of relevant literature.

Correction of post-traumatic anterior open bite by injection of botulinum toxin type A into the anterior belly of the digastric muscle: case report.

Post-traumatic anterior open bite can occur as a result of broken balance among the masticatory muscles. The superior hyoid muscle group retracts the mandible downward and contributes to the anterior open bite. Denervation of the digastric muscle by injection of botulinum toxin type A (BTX-A) can reduce the power of the digastric muscle and help to resolve the post-traumatic anterior open bite. A patient with a bilateral angle fracture had an anterior open bite even after undergoing three operations under general anesthesia and rubber traction. Although the open bite showed some improvement by the repeated operation, the occlusion was still unstable six weeks after the initial treatment. To eliminate the residual anterior open bite, BTX-A was injected into the anterior belly of the digastric muscle. Following injection of BTX-A, the anterior open bite showed immediate improvement. Complication and relapse were not observed during follow-up. Long-standing post-traumatic open bite could be successfully corrected by injection of BTX-A into the anterior belly of the digastric muscle without complication.