RESUMEN
It remains challenging to build up a multifunctional coating onto biodegradable magnesium (Mg) for biomedical use. In this study, a small amount of titanium dioxide (TiO2) has been incorporated in situ into phytic acid (PA) coating when it was chemically deposited on Mg substrate targeted to biodegradable implant applications. Ultraviolet (UV) irradiation was utilized in the liquid phase deposition of TiO2 to improve the quality of coating (PA&TiO2-UV). This PA&TiO2-UV coating was compact, thicker and more hydrophilic compared with sole PA or TiO2 coating. The PA&TiO2-UV coated Mg presented a seven times lower electrochemical corrosion current density as well as significantly slower in vitro degradation rate up to 500 h in phosphate buffer saline as compared to the direct PA coated Mg. In addition, the UV irradiation showed remarkably to promote the MC3T3-E1 pre-osteoblast cells adhesion and proliferation especially after 7 days of culture. Further, the PA&TiO2-UV coating adhered more firmly on Mg substrate after 90° bending than the other coatings, indicating a better mechanical compliance on Mg substrate. These results make this PA&TiO2-UV complex coating bodes well for biodegradation slowing-down, osteo-compatible as well as mechanical compliant modification of Mg for orthopedic implants applications.
Asunto(s)
Materiales Biocompatibles Revestidos/química , Magnesio/química , Osteoblastos/efectos de los fármacos , Ácido Fítico/química , Titanio/química , Implantes Absorbibles , Animales , Biodegradación Ambiental , Adhesión Celular , Línea Celular , Proliferación Celular , Corrosión , Cinética , Ensayo de Materiales , Ratones , Ortopedia , Osteoblastos/citología , Presión , Propiedades de Superficie , Rayos UltravioletaRESUMEN
PURPOSE: To analyze the biomechanical healing process on rigid fixation of sagittal fracture of the mandibular condyle (SFMC), and to provide guidelines for surgical treatment. METHODS: Three-dimensional finite element model (3D-FEAM) of mandible and condyle was established. The right condyle was simulated as SFMC with 0.1 mm space across the condyle length ways. The 3D-FEAM of rigid fixation was established. The biomechanical factors such as stress distribution of condylar surface, displacement around fracture, stress on the plate and stress shielding were calculated during 0, 4, 8 and 12-week after rigid fixation. RESULTS: The maximum equivalent stress of normal condyle was located at the area of middle 1/3 of condylar neck. The maximum equivalent stress at 0-week after fixation was 23 times than that on normal condyle. They were located at the condylar stump and the plate near inferior punctual areas of fracture line. There were little stress on the other areas. The maximum equivalent stress at 4, 8 and 12-week was approximately 6 times than that on normal condyle. They were located at the areas same as the area at 0-week. There were little stress on the other areas at the condyle. The maximum total displacement and maximum total corner were increased 0.57-0.75 mm and 0.01-0.09° respectively during healing process. The maximum equivalent stress at 0-week on the condylar trump was 5-6 times compared with that at 4, 8, and 12-week. The maximum equivalent stress, maximum total displacement and maximum total corner on the fractured fragment were not changed significantly during healing process. The maximum equivalent stress at 0-week on the plate was 7-9 times compared with that at 4, 8, 12-week. CONCLUSIONS: The stress of the condyle and stress shielding of the plate may be the reasons of absorbing and rebuilding on the condyle in healing process of SFMC. The biomechanical parameters increase obviously at 4-week after fixation. Elastic intermaxillary traction is necessary to decrease total displacement and total corner of the condyle, and liquid diet is necessary to decrease equivalent stress within 4 weeks. Rehabilitation training should be used to recover TMJ functions after 4 weeks because the condyle and mandible have the ability to carry out normal functions.