[Preparation of hybrid exosomes based on bovine milk exosomes and liposomes and pharmacodynamic study of sinomenine loaded exosomes in treatment of rheumatoid arthritis].

This study investigates the therapeutic effect of hybrid exosomes loaded with sinomenine(SIN) obtained by membrane fusion of milk exosomes with liposomes in collagen-induced arthritis(CIA) rats. Exosomes were isolated from fresh bovine milk by sucrose density gradient centrifugation, while liposomes were prepared using the emulsion solvent evaporation-low temperature curing method. Hybrid exosomes were characterized after membrane fusion through co-incubation: The morphology was detected by transmission electron microscopy, the particle size and potential by nanoparticle size potentiostat, and the expressions of surface characteristic proteins CD63 and TSG101 before and after fusion by Western blot(WB). The drug loading capacity and encapsulation rate of sinomenine were measured after the loading of sinomenine on exosomes by ultrasonic method. The CIA rat model was induced by collagen antibody. The efficacy experiment consisted of the control group, model group, SIN group, SIN-liposome group, SIN-milk exosome group, SIN-hybrid exosome group and positive drug(dexamethasone) group. The changes in body mass of rats during administration were recorded. Besides, the foot swelling, immune organ index, arthritis index, microcirculation index, synovial histopathology, and serum inflammatory factor levels detected by enzyme-linked immunosorbent assay were observed for pharmacodynamical study. Under transmission electron microscopy, both hybrid exosomes and milk exosomes showed saucer-like appearance. After co-incubation, the exosome particle size increased from(97.92±3.42)nm to(132.70±4.07)nm, and the Zeta potential changed from(-2.01±0.33)mV to(-17.90±2.13)mV. WB assay showed that CD63 and TSG101 proteins were normally expressed in milk exosomes and hybrid exosomes. The encapsulation rate of milk exosomes was 31.64%±2.48%, with a drug loading of 2.35%±0.52%, while the hybrid exosomes exhibited an encapsulation rate of 48.21%±3.12% and drug loading of 3.17%±0.36%, as determined by the microplate reader. Pharmacodynamic results showed that compared with the model group, the general condition, swelling degree of foot, arthritis index and immune organ index of all drug administration groups were significantly improved(P<0.05, P<0.01); microvascular comprehensive score and vascular resistance were significantly decreased(P<0.05, P<0.01); serum levels of TNF-α, IL-1ß and IL-6 inflammatory factors were significantly decreased(P<0.01); and the lesions of synovial tissue were improved to some extent. Meanwhile, compared with the SIN group, SIN-liposome group and SIN-milk exosome group, the SIN-hybrid exosome group had a more stable and durable drug effect. The hybrid exosomes obtained by co-incubation of milk-derived exosomes with liposomes successfully improved the drug carrying capacity of exosomes and biocompatibility of liposomes. The hybrid exosomes loaded with sinomenine have good efficacy on CIA model rats, and can effectively solve the problems of TCM such as sinomenine, which have good efficacy but short biological half-life. The study provides new insights for the development of TCM and the treatment of diseases such as rheumatoid arthritis.

Highly Stable, Protein-Resistant Surfaces via the Layer-by-Layer Assembly of Poly(sulfobetaine methacrylate) and Tannic Acid.

Zwitterionic materials have received great attention because of the non-fouling property. As a result of the electric neutrality of zwitterionic polymers, their layer-by-layer (LBL) assembly is generally conducted under specific conditions, such as very low pH values or ionic strength. The formed multilayers are unstable at high pH or in a high ionic strength environment. Therefore, the formation of highly stable multilayers of zwitterionic polymers via the LBL assembly process is still challenging. Here, we report the LBL assembly of poly(sulfobetaine methacrylate) (PSBMA) with a polyphenol, tannic acid (TA), for protein-resistant surfaces. The assembly process was monitored by a quartz crystal microbalance (QCM) and variable-angle spectroscopic ellipsometry (VASE), which confirms the formation of thin multilayer films. We found that the (TA/PSBMA)n multilayers are stable over a wide pH range of 4-10 and in saline, such as 1 M NaCl or urea solution. The surface morphology and chemical composition were characterized by specular reflectance Fourier transform infrared spectroscopy (FTIR/SR), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). Furthermore, (TA/PSBMA)n multilayers show high hydrophilicity, with a water contact angle lower than 15°. A QCM was used to record the dynamic protein adsorption process. Adsorption amounts of bovine serum albumin (BSA), lysozyme (Lys), and hemoglobin (Hgb) on (TA/PSBMA)20 multilayers decreased to 0.42, 52.9, and 37.9 ng/cm(2) from 328, 357, and 509 ng/cm(2) on a bare gold chip surface, respectively. In addition, the protein-resistance property depends upon the outmost layer. This work provides new insights into the LBL assembly of zwitterionic polymers.

Glycosylation of the polypropylene membrane surface via thiol-yne click chemistry for lectin adsorption.

Glycosylated membrane, as one of the most important affinity membranes, permits affinity separation/purification of proteins based on carbohydrate-protein interactions. It is an important scientific issue to screen facile method for fabricating the glycosylated membrane surface with high glycosyl density. Such a surface can be fabricated by the direct covalent immobilization of carbohydrate ligands on the surfaces of microporous polypropylene membrane (MPPM). First, alkyne-functionalized membrane surface was fabricated by plasma pretreatment combined with UV-induced graft polymerization of 3-(trimethylsilyl) propargyl methacrylate. Then, the glycosylated membrane surface was directly fabricated with the thiol-yne click reaction to ensure rapid process, improved efficiency, and high glycosyl density. Chemical and physical properties of the membrane surface were characterized by ATR/FT-IR, XPS, FESEM and water contact angle measurement. Static lectin adsorption indicates that the glycosylated membrane can specifically adsorb lectin concanavalin A (Con A) other than peanut agglutinin (PNA). Break through curves from dynamic Con A adsorption show the membrane has unique properties such as strong specificity, high adsorption capacity, and reversible binding capability. We suggest that the prepared glycosylated membrane is of great potentials in affinity membrane chromatography for rapid and high-resolution separation/purification of lectins.

Surface glycosylation of polymer membrane by thiol-yne click chemistry for affinity adsorption of lectin.

We present a novel approach to constructing glycosylated surface for microporous membrane. Carbohydrate derivative can be facilely bound onto the alkyne-modified membrane surface via thiol-yne click chemistry. The glycosylated membrane surface shows an excellent affinity adsorption to lectin on the basis of carbohydrate-protein recognition.